Experimental investigation of a multi-function heat pump under various operating modes

Heat pumps have been spotlighted as efficient building energy systems because they have great potentials for energy reduction in building air conditioning and reducing CO₂ emission. In this study, a multi-function heat pump which has the functions of heating, cooling, and hot water supply was designed and its performance was investigated according to operating modes. In the cooling-hot water mode, the capacity and COP were enhanced as compared to other modes because the waste heat from the outdoor heat exchanger was utilized as useful heat in the indoor heat exchanger. In the heating and hot water supply mode, the compressor speed should be increased to get appropriate heating and hot water capacities. For all operating modes, the system could be optimized by adjusting the superheat.     

基于圆柱源理论模型的U型埋管换热器的模拟研究

分析了圆柱热源(热汇)理论模型,运用圆柱源理论对太阳能-土壤源联合运行热泵系统进行连续20d运行的状况进行模拟,得出联合运行模式较单独土壤源运行模式节能8%~10%,可为圆柱源理论模型应用和太阳能-土壤源热泵运行模式的选择提供参考。引入“负荷集合”思想对圆柱热源(热汇)理论模型进行改进,使其适合于对土壤源热泵的全年运行进行模拟,模拟过程更为快捷。     

Performance investigation of the heat pump and power generation integration system

A novel heat pump and power generation integration system (HPPGIS) using solar energy as a low temperature heat source was presented in this study. This system could be operated in both an organic Rankine cycle power generation (ORC‐PG) mode and a reverse Carnot cycle heat pump (RCC‐HP) mode. Compared with a single heat pump and power generation system, this system improved the utilization efficiency of solar energy, thus showing potential for the generation of economic benefits. Contrastive analyses of different working fluids using ORC‐PG and RCC‐HP systems were conducted first, leading to the selection of R142b and R245fa as optimal fluids. Then, an experimental investigation of the system was carried out under different conditions. A heat pump and ORC system model was proposed and validated by comparing experimental and simulated values. The experimental results indicated that the HPPGIS had good feasibility and stability in both modes. In the ORC‐PG mode, HPPGIS had a power output of 1.29 kW and a thermal efficiency of 4.71% when the water inlet temperature of the evaporator was 90.03°C. In the RCC‐HP mode, HPPGIS had a COP of 3.16 and a heat capacity of 33.24 kW when the water outlet temperature of the condenser was 106.23°C.     

分液热泵空调系统的制热性能研究

随着热泵空调的普及,热泵空调的能耗占比不断增大,其节能问题成为了关注焦点。换热器对系统性能有着重要的影响,如何通过改进换热器来提升系统性能则成为了研究的热点。其中分液冷凝器作为一种新型的换热设备,能对系统制冷性能产生积极影响。但热泵空调系统在制热工况下,分液冷凝器变成气液分离式蒸发器,其系统制热性能尚未可知。通过实验研究,调整毛细管长度和制冷剂充注量,发现在国家标准工况下分液热泵空调系统的最大制热量比原系统高4.50%,C OP比原系统高7.93%,所对应的毛细管长度为700 mm,制冷剂充注量为700 g。且制冷剂过充注的情况下,分液热泵空调系统的制热性能比较稳定。     

Cooling performance of a vertical ground-coupled heat pump system installed in a school building

This paper presents the cooling performance of a water-to-refrigerant type ground heat source heat pump system (GSHP) installed in a school building in Korea. The evaluation of the cooling performance has been conducted under the actual operation of GSHP system in the summer of year 2007. Ten heat pump units with the capacity of 10 HP each were installed in the building. Also, a closed vertical typed-ground heat exchanger with 24 boreholes of 175 m in depth was constructed for the GSHP system. To analyze the cooling performance of the GSHP system, we monitored various operating conditions, including the outdoor temperature, the ground temperature, and the water temperature of inlet and outlet of the ground heat exchanger. Simultaneously, the cooling capacity and the input power were evaluated to determine the cooling performance of the GSHP system. The average cooling coefficient of performance (COP) and overall COP of the GSHP system were found to be ～8.3 and ～5.9 at 65% partial load condition, respectively. While the air source heat pump (ASHP) system, which has the same capacity with the GSHP system, was found to have the average COP of ～3.9 and overall COP of ～3.4, implying that the GSHP system is more efficient than the ASHP system due to its lower temperature of condenser.     

Exergetic performance evaluation of heat pump systems having various heat sources

In this study heat pump systems having different heat sources were investigated experimentally. Solar‐assisted heat pump (SAHP), ground source heat pump (GSHP) and air source heat pump (ASHP) systems for domestic heating were tested. Additionally, their combination systems, such as solar‐assisted‐ground source heat pump (SAGSHP), solar‐assisted‐air source heat pump (SAASHP) and ground–air source heat pump (GSASHP) were tested. All the heat pump systems were designed and constructed in a test room with 60 m² floor area in Firat University, Elazig (38.41°N, 39.14°E), Turkey. In evaluating the efficiency of heat pump systems, the most commonly used measure is the energy or the first law efficiency, which is modified to a coefficient of performance for heat pump systems. However, for indicating the possibilities for thermodynamic improvement, inadequate energy analysis and exergy analysis are needed. This study presents an exergetic evaluation of SAHP, GSHP and ASHP and their combination systems. The exergy losses in each of the components of the heat pump systems are determined for average values of experimentally measured parameters. Exergy efficiency in each of the components of the heat pump systems is also determined to assess their performances. The coefficient of performance (COP) of the SAHP, GSHP and ASHP were obtained as 2.95, 2.44 and 2.33, whereas the exergy losses of the refrigerant subsystems were found to be 1.342, 1.705 and 1.942 kW, respectively. The COP of SAGSHP, SAASHP and GSASHP as multiple source heat pump systems were also determined to be 3.36, 2.90 and 2.14, whereas the exergy losses of the refrigerant subsystems were approximately 2.13, 2.996 and 3.113 kW, respectively. In addition, multiple source heat pump systems were compared with single source heat pump systems on the basis of the COP. Exergetic performance coefficient (EPC) is introduced and is applied to the heat pump systems having various heat sources. The results imply that the functional forms of the EPC and first law efficiency are different. Results show that Ex_loss,total becomes a minimum value when EPC has a maximum value. Copyright © 2008 John Wiley & Sons, Ltd.     

Solar-assisted absorption heat pumps feasibility

An absorption system can be used for space cooling as well as for space heating. This dual purpose may be achieved by using the system as heat pump in wintertime. Absorption heat pump heating may be an interesting alternative, particularly for countries where there is a shortage of electric power.When an absorption unit is used as heat pump, its mode of operation is not modified: the internal temperatures of the cycle are only raised. Commercially available LiBr units were tested as heat pumps. COP and heating capacity were considered as a function of cold source temperature for different temperatures of the useful heat. The COP arrived at 1.7, which must be considered a high value for a thermally driven heat pump.Simulations were carried out in order to compare the performance of “conventional” solar, solar assisted heat pump and the combined series system under two different climate conditions. The series system showed performance 25–75 per cent better than “conventional” solar alone.     

A study on the performance enhancement of heat pump using electric heater under the frosting condition: Heat pump under frosting condition

The purpose of the present study is to enhance the heating capacity and increase COP under the frosting condition during heating operation of small capacity air-to-air heat pump. We applied an electric heater in front of outdoor unit of heat pump instead of indoor unit as usual. When the outdoor temperature is 2 °C/1 °C (DB/WB), the present heat pump turns on the electric heater in outdoor unit. The heating capacity increases 38.0% and COP increases 57.0% in comparison with those of conventional heat pump. When the outdoor temperature is 4 °C/2 °C (DB/WB), the electric heater is in ON/OFF mode according to the temperature of the evaporator. The heating capacity increases 9.1% and COP increases 71.1% in comparison with those of conventional heat pump.     

Heat-pipe enhanced solar-assisted heat pump water heater

A heat-pipe enhanced solar-assisted heat pump water heater (HPSAHP) is studied. HPSAHP is a heat pump with dual heat sources that combines the performance of conventional heat pump and solar heat pipe collector. HPSAHP operates in heat-pump mode when solar radiation is low and in heat-pipe mode without electricity consumption when solar radiation is high. HPSAHP can thus achieve high energy efficiency. A prototype was designed and built in the present study. An outdoor test for a HPSAHP in the present study has shown that COP of the hybrid-mode operation can reach 3.32, an increase of 28.7% as compared to the heat-pump mode COP (2.58).     

Performance enhancement of a subcooled cold storage air conditioning system

This article experimentally investigates the enhancement of thermal performance for an air conditioning system utilizing a cold storage unit as a subcooler. The cold storage unit is composed of an energy storage tank, liquid-side heat exchanger, suction-side heat exchanger and energy storage material (ESM), water. When the cooling load is lower than the nominal cooling capacity of the system, the cold storage unit can store extra cold energy of the system to subcool the condenser outlet refrigerant. Hence, both the cooling capacity and coefficient of performance (COP) of the system will be increased. This experiment tests the two operation modes: subcooled mode with energy storage and non-subcooled mode without energy storage. The results show that for fixed cooling loads at 3.05 kW, 3.5 kW and 3.95 kW, the COP of the subcooled mode are 16.0%, 15.6% and 14.1% higher than those of the non-subcooled mode, respectively. In the varied cooling load experiments, the COP of the subcooled cold storage air conditioning system is 15.3% higher than the conventional system.     

太阳能和空气源复合热泵的最优模式切换分析

太阳能和空气源复合热泵在不同模式下具有不同性能,如何在实际应用中以最佳的工作模式运行,对提高系统综合性能至关重要,为此提出2种用于实现系统最优模式切换的判断方法：1）基于最优模式切换的太阳能辐射强度和环境温度的复合环境参数范围表;2）流经2个蒸发器（太阳能集热/蒸发器和风冷蒸发器）的制冷剂质量流量分配比。基于此,在工程方程求解器（EES）中建立太阳能/空气双源辅助热泵热水器的仿真模型。首先,基于上海松江地区的气候条件模拟比较不同模式下的系统性能,再分析和讨论将复合环境参数范围表和质量流量分配比作为系统最优模式切换的判断方法的可行性。结果表明,在相同环境温度下,随着太阳辐射强度的增加,系统最优运行模式将由太阳能-空气模式转变为太阳能模式。此外,将流经2个蒸发器的制冷剂质量流量分配比作为模式切换的准则是可行的,对于本系统其最优运行模式由太阳能-空气模式转变为太阳能模式时的质量流量分配比临界值约为2.02。     

基于平板热管的太阳能-空气能双源集热蒸发器性能实验研究

设计一种基于平板热管的太阳能-空气能双源集热蒸发器及由其组成的新型直膨式热泵系统,并对其进行实验研究与分析。实验测试平板热管在制冷剂低温取热条件下的均温性与导热性能,热泵运行工况下集热蒸发器表面温度分布、光电光热性能,以及在不同天气条件不同运行模式下热泵系统性能。结果表明,平板热管在低温取热条件下当量导热系数可达6.8×10⁵W/(m·℃),集热蒸发器运行时纵向最大温差为3.9℃;在夏季晴朗天气条件下运行太阳能模式制热水时热泵平均COP为3.62;在低辐照阴天下运行太阳能-空气能双源模式与太阳能模式相比,单位面积集热功率提高18.8%,系统平均COP提高5.7%;在无辐照的夜晚,运行空气源模式系统COP为2.54。     

复合热源太阳能热泵供热系统及其性能模拟

提出了一种复合热源太阳能热泵供热系统,通过阀门切换,可根据不同的天气状况改变运行模式,以空气和太阳辐射作为热源制取供暖用水。针对所设计的10kW供热系统,建立了系统的数学模型,对热泵串联集热器(SC+HP)及集热器串联热泵(H+SC)两种运行模式下的循环性能进行了计算机模拟分析,并计算了系统的全年运行状况。从模拟结果可以看出,在模拟进水温度区间内,HP+SC模式下热泵COP较高,最高比SC+HP模式高2.58%;而SC+HP模式集热器热性能较好,总热效率更高,最高比HP+SC模式高2.62%。     

Laboratory investigation on the use of thermally enhanced phase change material to improve the performance of borehole heat exchangers for ground source heat pumps

Ground source heat pumps have high efficiency and high capital cost primarily due to borehole drillings. This research investigates the inclusion of high‐conductivity phase change material (PCM) in the borehole heat exchanger of a ground source heat pump to reduce the borehole length required and improve its coefficient of performance (COP). In the laboratory model, the borehole heat exchanger was represented by a cylindrical electrical heater having a total power of 9.216 W, operating for 1 hour while resting for 3 hours. Surrounding the heater in the annular region, either soil, PCM, or high‐conductivity PCM was used as grouting material. The annular region was surrounded by a large amount of soil enclosed in a large bin as a representation of ground soil. The high‐conductivity graphite was impregnated with the commercial PCM “PureTemp29.” Results from the experiments revealed that the PCM is able to decrease the temperature fluctuations in the annular and soil regions, while graphite increases the thermal conductivity of the annular region and hence increases the rate of heat dissipation from the heater to the soil surrounding it. The maximum COP values of a ground source heat pump calculated assuming ideal reversed Carnot cycle for cooling mode showed an increase of approximately 81% with PCM and by 112% with graphite‐enhanced PCM.     

Experimental investigation of a vapor compression heat pump used for cooling and heating applications

The present work aims at evaluating the performance characteristics of a vapor compression heat pump (VCHP) for simultaneous space cooling (summer air conditioning) and hot water supply. In order to achieve this objective, a test facility was developed and experiments were performed over a wide range of evaporator water inlet temperature (14:26 °C) and condenser water inlet temperature (22:34 °C). R134a was used as a primary working fluid whereas water was adopted as a secondary heat transfer fluid at both heat source (evaporator) and heat sink (condenser) of the heat pump. Performance characteristics of the considered heat pump were characterized by outlet water temperatures, water side capacities and coefficient of performance (COP) for various operating modes namely: cooling, heating and simultaneous cooling and heating. Results showed that COP increases with the evaporator water inlet temperature while decreases as the condenser water inlet temperature increases. However, the evaporator water inlet temperature has more effect on the performance characteristics of the heat pump than that of condenser water inlet temperature. Actual COP of cooling mode between 1.9 to 3.1 and that of heating mode from 2.9 to 3.3 were obtained. Actual simultaneous COP between 3.7 and 4.9 was achieved.     

System optimization and experimental research on air source heat pump water heater

This paper deals with the system optimization of air source heat pump water heater (ASHPWH), including calculating and testing. The ASHPWH system consists of a heat pump, a water tank and connecting pipes. Air energy is absorbed at the evaporator and pumped to storage tank via a Rankine cycle. The coil pipe/condenser releases condensing heat of the refrigerant to the water side. An ASHPWH using a rotary compressor heated the water from initial temperature to the set temperature (55 °C). The capillary tube length, the filling quantity of refrigerant, the condenser coil tube length and system matching are discussed accordingly. From the testing results, it could be seen that the system performance COP could be improved obviously.     

Experimental investigation of the performance of a solar‐assisted ground‐source heat pump system for greenhouse heating

The main objective of the present study is to investigate the performance characteristics of a solar‐assisted ground‐source heat pump system (SAGSHPS) for greenhouse heating with a 50 m vertical 1¼ in nominal diameter U‐bend ground heat exchanger. This system was designed and installed in the Solar Energy Institute, Ege University, Izmir (568 degree days cooling, base: 22°C, 1226 degree days heating, base: 18°C), Turkey. Based upon the measurements made in the heating mode, the heat extraction rate from the soil is found to be, on average, 54.08 Wm^?1 of bore depth, while the required borehole length in meter per kW of heating capacity is obtained as 12.57. The entering water temperature to the unit ranges from 8.2 to 16.2°C, with an average value of 9.1°C. The greenhouse air is at a maximum day temperature of 25°C and night temperature of 14°C with a relative humidity of 40%. The heating coefficient of performance of the heat pump (COP_HP) is about 2.13 at the end of a cloudy day, while it is about 2.84 at the end of sunny day and fluctuates between these values in other times. The COP values for the whole system are also obtained to be 5–15% lower than COP_HP. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical simulation of the performance of a solar-earth source heat pump system

Solar-earth source heat pump (SESHP) is a new type of energy saving air conditioner. In this paper, numerical simulation of the performance of a solar-earth source heat pump system (SESHPS) operated at alternate or combined mode is carried out respectively. The results indicate that a resuming-rate of 30–60% of the earth temperature near buried coil can be preferable when SESHPS is operated alternately at a period of 24 h, and the proportion of the operation time of solar-assisted heat pump (SAHP ) should be confined to 42–58%. When SESHPS is operated at combined modes 2, the energy-saving rate with and without heat storage water tank is 14.5% and 10.4%, respectively, compared with ground source heat pump (GSHP). As for the overall effect, the combined operation mode with water tank in which the heated water flows through the solar collector first and then through the buried coil is preferable. The results are significant for the engineering design, operation and management of SESHPS.     

Performance of a multi-functional direct-expansion solar assisted heat pump system

This paper reports on the long-term performance of a direct-expansion solar assisted heat pump (DX-SAHP) system for domestic use, which can offer space heating in winter, air conditioning in summer and hot water during the whole year. The system employs a bare flat-plate collector array with a surface area of 10.5 m², a variable speed compressor, a storage tank with a total volume of 1 m³ and radiant floor heating unit. The performance under different operation modes is presented and analyzed in detail. For space-heating-only mode, the daily-averaged heat pump COP varied from 2.6 to 3.3, while the system COP ranged from 2.1 to 2.7. For water-heating-only mode, the DX-SAHP system could supply 200 l or 1000 l hot water daily, with the final temperature of about 50 °C, under various weather conditions in Shanghai, China. For space-cooling-only mode, the compressor operates only at night to take advantage of a utility’s off-peak electrical rates by chilling water in the thermal storage tank for the daytime air-conditioning. It shows that, the multi-functional DX-SAHP system could guarantee a long-term operation under very different weather conditions and relatively low running cost for a whole year.     

Experimental study on a monovalent inverter-driven water-to-water heat pump with a desuperheater for low energy houses

In this study, a novel monovalent inverter-driven water-to-water heat pump with a desuperheater was developed. In this unique system, domestic hot water is produced at a constant temperature controlled by a variable flow rate and stored in a tank. The heat demand is constantly matched by the system through the use of an inverter-driven compressor, which eliminates the need for a buffer tank. Three heating configurations of the system were examined with respect to variable climate conditions and two space heating target temperatures: space heating (mode 1), domestic hot water production (mode 2) and a combination of both (mode 3). Mappings of the performance variables per frequency were constructed for mode 3. For the other modes, the highest COP was identified for each examined climate condition. The difference between modes 1 and 3 was less than 5% for every variable. The space heating target temperature had a strong influence on both modes, showing an average difference of 29% in the COP between 35 °C and 45 °C. Mode 2 exhibited a considerably reduced COP compared to the other modes, as well as the lowest refrigerant mass flow rate and highest compression ratio among the three modes. From the previous results and the examination of the compressor, the compression ratio presents itself as a key parameter that can help to increase the COP if maintained at low values. The results of this research could be applied to the design of a control methodology for monovalent heat pumps.