Nexuses Between the Chemical Design and Performance of Small Molecule Dopant-Free Hole Transporting Materials in Perovskite Solar Cells

Perovskite solar cells (PSCs) have grabbed much attention of researchers owing to their quick rise in power conversion efficiency (PCE). However, long-term stability remains a hurdle in commercialization, partly due to the inclusion of necessary hygroscopic dopants in hole transporting materials, enhancing the complexity and total cost. Generally, the efforts in designing dopant-free hole transporting materials (HTMs) are devoted toward small molecule and polymeric HTMs, where small molecule based HTMs (SM-HTMs) are dominant due to their reproducibility, facile synthesis, and low cost. Still, the state-of-art dopant-free SM-HTM has not been achieved yet, mainly because of the knowledge gap between device engineering and molecular designs. From a molecular engineering perspective, this article reviews dopant-free SM-HTMs for PSCs, outlining analyses of chemical structures with promising properties toward achieving effective, low-cost, and scalable materials for devices with higher stability. Finally, an outlook of dopant-free SM-HTMs toward commercial application and insight into the development of long-term stability PSCs devices is provided.     

High‐Performance Inverted Planar Perovskite Solar Cells Enhanced by Thickness Tuning of New Dopant‐Free Hole Transporting Layer

A new hole transporting material (HTM) named DMZ is synthesized and employed as a dopant‐free HTM in inverted planar perovskite solar cells (PSCs). Systematic studies demonstrate that the thickness of the hole transporting layer can effectively enhance the morphology and crystallinity of the perovskite layer, leading to low series resistance and less defects in the crystal. As a result, the champion power conversion efficiency (PCE) of 18.61% with J_SC = 22.62 mA cm^?2, V_OC = 1.02 V, and FF = 81.05% (an average one is 17.62%) is achieved with a thickness of ≈13 nm of DMZ (2 mg mL^?1) under standard global AM 1.5 illumination, which is ≈1.5 times higher than that of devices based on poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonic acid) (PEDOT:PSS). More importantly, the devices based on DMZ exhibit a much better stability (90% of maximum PCE retained after more than 556 h in air (relative humidity ≈ 45%–50%) without any encapsulation) than that of devices based on PEDOT:PSS (only 36% of initial PCE retained after 77 h in same conditions). Therefore, the cost‐effective and facile material named DMZ offers an appealing alternative to PEDOT:PSS or polytriarylamine for highly efficient and stable inverted planar PSCs.     

Highly π-extended copolymer as additive-free hole-transport material for perovskite solar cells

Organolead halide perovskite solar cells have achieved a certified power-conversion efficiency (PCE) of 22.1% and are thus among the most promising candidates for next-generation photovoltaic devices. To date, most high-efficiency perovskite solar cells have employed arylamine-based hole-transport materials (HTMs), which are expensive and have a low mobility. The complicated doping procedures and the potentially stability-adverse dopants used in these HTMs are among the major bottlenecks for the commercialization of perovskite solar cells (PSCs). Herein, we present a polythiophene-based copolymer (PDVT-10) with a hole mobility up to 8.2 cm²·V^?1·s^?1 and a highest occupied molecular orbital level of ?5.28 eV as a hole-transport layer (HTL) for a PSC. A device based on this new HTM exhibited a high PCE of 13.4% under 100 mW·cm^?2 illumination, which is one of the highest PCEs reported for the dopant-free polymer-based HTLs. Moreover, PDVT-10 exhibited good solution processability, decent air stability, and thermal stability, making it a promising candidate as an HTM for PSCs.

Open image in new window

     

Highly Efficient p‐i‐n Perovskite Solar Cells Utilizing Novel Low‐Temperature Solution‐Processed Hole Transport Materials with Linear π‐Conjugated Structure

Alternative low‐temperature solution‐processed hole‐transporting materials (HTMs) without dopant are critical for highly efficient perovskite solar cells (PSCs). Here, two novel small molecule HTMs with linear π‐conjugated structure, 4,4′‐bis(4‐(di‐p‐toyl)aminostyryl)biphenyl (TPASBP) and 1,4′‐bis(4‐(di‐p‐toyl)aminostyryl)benzene (TPASB), are applied as hole‐transporting layer (HTL) by low‐temperature (sub‐100 °C) solution‐processed method in p‐i‐n PSCs. Compared with standard poly(3,4‐ethylenedioxythiophene): poly(styrenesulfonic acid) (PEDOT:PSS) HTL, both TPASBP and TPASB HTLs can promote the growth of perovskite (CH₃NH₃PbI₃) film consisting of large grains and less grain boundaries. Furthermore, the hole extraction at HTL/CH₃NH₃PbI₃ interface and the hole transport in HTL are also more efficient under the conditions of using TPASBP or TPASB as HTL. Hence, the photovoltaic performance of the PSCs is dramatically enhanced, leading to the high efficiencies of 17.4% and 17.6% for the PSCs using TPASBP and TPASB as HTL, respectively, which are ≈40% higher than that of the standard PSC using PEDOT:PSS HTL.     

Extrinsic Ion Distribution Induced Field Effect in CsPbIBr2 Perovskite Solar Cells

Excellent power conversion efficiency (PCE) and stability are the primary forces that propel the all‐inorganic cesium‐based halide perovskite solar cells (PSCs) toward commercialization. However, the intrinsic high density of trap state and internal nonradiative recombination of CsPbIBr₂ perovskite film are the barriers that limit its development. In the present study, a facile additive strategy is introduced to fabricate highly efficient CsPbIBr₂ PSCs by incorporating sulfamic acid sodium salt (SAS) into the perovskite layer. The additive can control the crystallization behaviors and optimize morphology, as well as effectively passivate defects in the bulk perovskite film, thereby resulting in a high‐quality perovskite. In addition, SAS in perovskite has possibly introduced an additional internal electric field effect that favors electron transport and injection due to inhomogeneous ion distribution. A champion PCE of 10.57% (steady‐output efficiency is 9.99%) is achieved under 1 Sun illumination, which surpasses that of the contrast sample by 16.84%. The modified perovskite film also exhibits improved moisture stability. The unencapsulated device maintains over 80% initial PCE after aging for 198 h in air. The results provide a suitable additive for inorganic perovskite and introduce a new conjecture to explain the function of additives in PSCs more rationally.     

Highly Efficient and Stable GABr-Modified Ideal-Bandgap (1.35 eV) Sn/Pb Perovskite Solar Cells Achieve 20.63% Efficiency with a Record Small Voc Deficit of 0.33 V

1.5–1.6 eV bandgap Pb-based perovskite solar cells (PSCs) with 30–31% theoretical efficiency limit by the Shockley–Queisser model achieve 21–24% power conversion efficiencies (PCEs). However, the best PCEs of reported ideal-bandgap (1.3–1.4 eV) Sn–Pb PSCs with a higher 33% theoretical efficiency limit are <18%, mainly because of their large open-circuit voltage (V_oc) deficits (>0.4 V). Herein, it is found that the addition of guanidinium bromide (GABr) can significantly improve the structural and photoelectric characteristics of ideal-bandgap (≈1.34 eV) Sn–Pb perovskite films. GABr introduced in the perovskite films can efficiently reduce the high defect density caused by Sn²⁺ oxidation in the perovskite, which is favorable for facilitating hole transport, decreasing charge-carrier recombination, and reducing the V_oc deficit. Therefore, the best PCE of 20.63% with a certificated efficiency of 19.8% is achieved in 1.35 eV PSCs, along with a record small V_oc deficit of 0.33 V, which is the highest PCE among all values reported to date for ideal-bandgap Sn–Pb PSCs. Moreover, the GABr-modified PSCs exhibit significantly improved environmental and thermal stability. This work represents a noteworthy step toward the fabrication of efficient and stable ideal-bandgap PSCs.     

Thermally Stable MAPbI3 Perovskite Solar Cells with Efficiency of 19.19% and Area over 1 cm2 achieved by Additive Engineering

Solution‐processed perovskite (PSC) solar cells have achieved extremely high power conversion efficiencies (PCEs) over 20%, but practical application of this photovoltaic technology requires further advancements on both long‐term stability and large‐area device demonstration. Here, an additive‐engineering strategy is developed to realize a facile and convenient fabrication method of large‐area uniform perovskite films composed of large crystal size and low density of defects. The high crystalline quality of the perovskite is found to simultaneously enhance the PCE and the durability of PSCs. By using the simple and widely used methylammonium lead iodide (MAPbI₃), a certified PCE of 19.19% is achieved for devices with an aperture area of 1.025 cm², and the high‐performing devices can sustain over 80% of the initial PCE after 500 h of thermal aging at 85 °C, which are among the best results of MAPbI₃‐based PSCs so far.     

Record Efficiency Stable Flexible Perovskite Solar Cell Using Effective Additive Assistant Strategy

Even though the power conversion efficiency (PCE) of rigid perovskite solar cells is increased to 22.7%, the PCE of flexible perovskite solar cells (F‐PSCs) is still lower. Here, a novel dimethyl sulfide (DS) additive is developed to effectively improve the performance of the F‐PSCs. Fourier transform infrared spectroscopy reveals that the DS additive reacts with Pb²⁺ to form a chelated intermediate, which significantly slows down the crystallization rate, leading to large grain size and good crystallinity for the resultant perovskite film. In fact, the trap density of the perovskite film prepared using the DS additive is reduced by an order of magnitude compared to the one without it, demonstrating that the additive effectively retards transformation kinetics during the thin film formation process. As a result, the PCE of the flexible devices increases to 18.40%, with good mechanical tolerance, the highest reported so far for the F‐PSCs. Meanwhile, the environmental stability of the F‐PSCs significantly enhances by 1.72 times compared to the device without the additive, likely due to the large grain size that suppresses perovskite degradation at grain boundaries. The present strategy will help guide development of high efficiency F‐PSCs for practical applications.     

Intensive Exposure of Functional Rings of a Polymeric Hole‐Transporting Material Enables Efficient Perovskite Solar Cells

A variety of dopant‐free hole‐transporting materials (HTMs) is effectively applied in perovskite solar cells (PSCs); however, HTMs with the additional function of HTM/perovskite interfacial optimization that is crucial to their photovoltaic performance are really limited. In this work, the design of an HTM bearing an intensive exposure of its functional aromatic rings to perovskite layer via side‐chain engineering is attempted. With an edge‐on orientation and a short distance to perovskite, this HTM was expected to display an excellent ability to extract holes from and passivate defects in the perovskite layer. To demonstrate this strategy, an alternating copolymer was constructed with a 2,5‐di‐2‐ethylhexyloxy‐1,4‐phenylene unit and a bithiophene unit, and the PSC based on this polymer showed an ultrahigh short‐circuit current density of 25.50 mA cm^?2, which was the highest so far presented by dopant‐free organic HTMs. A comparable power conversion efficiency of 19.68% (certified: 19.5%) to that of a control 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) device (19.81%) was thus obtained, which is the highest value ever reported for mesoporous PSCs based on dopant‐free polymeric HTMs.     

Co-Solvent Engineering Contributing to Achieve High-Performance Perovskite Solar Cells and Modules Based on Anti-Solvent Free Technology

The pinhole-free and defect-less perovskite film is crucial for achieving high efficiency and stable perovskite solar cells (PSCs), which can be prepared by widely used anti-solvent crystallization strategies. However, the involvement of anti-solvent requires precise control and inevitably brings toxicity in fabrication procedures, which limits its large-scale industrial application. In this work, a facile and effective co-solvent engineering strategy is introduced to obtain high- quality perovskite film while avoiding the usage of anti-solvent. The uniform and compact perovskite polycrystalline films have been fabricated through the addition of co-solvent that owns strong coordination capacity with perovskite components , meanwhile possessing the weaker interaction with main solvent . With those strategies, a champion power conversion efficiency (PCE) of 22% has been achieved with the optimal co-solvent, N-methylpyrrolidone (NMP) and without usage of anti-solvent. Subsequently, PSCs based on NMP show high repeatability and good shelf stability (80% PCE remains after storing in ambient condition for 30 days). Finally, the perovskite solar module (5 × 5 cm) with 7 subcells connects in series yielding champion PCE of 16.54%. This strategy provides a general guidance of co-solvent selection for PSCs based on anti-solvent free technology and promotes commercial application of PSCs.     

Highly Efficient and Stable Perovskite Solar Cells: Competitive Crystallization Strategy and Synergistic Passivation

Defects of perovskite (PVK) films are one of the main obstacles to achieving high-performance perovskite solar cells (PSCs). Here, the authors fabricated highly efficient and stable PSCs by introducing prolinamide (ProA) into the PbI₂ precursor solution, which improves the performance of PSCs by the competitive crystallization and efficient defect passivation of perovskite. The theoretical and experimental results indicate that ProA forms an adduct with PbI₂, competes with free I⁻ to coordinate with Pb²⁺, leads to the increase of the energy barrier of crystallization, and slows down the crystallization rate. Furthermore, the dual-site synergistic passivation of ProA is revealed by density functional theory (DFT) calculations and experimental results. ProA effectively reduces non-radiative recombination in the resultant films to improve the photovoltaic performance of PSCs. Notably, ProA-assisted PSCs achieve 24.61% power conversion efficiency (PCE) for the champion device and the stability of PSCs devices under ambient and thermal environments is improved.     

Stable and High-Efficiency Methylammonium-Free Perovskite Solar Cells

Organic–inorganic metal halide perovskite solar cells (PSCs) have achieved certified power conversion efficiency (PCE) of 25.2% with complex compositional and bandgap engineering. However, the thermal instability of methylammonium (MA) cation can cause the degradation of the perovskite film, remaining a risk for the long-term stability of the devices. Herein, a unique method is demonstrated to fabricate highly phase-stable perovskite film without MA by introducing cesium chloride (CsCl) in the double cation (Cs, formamidinium) perovskite precursor. Moreover, due to the suboptimal bandgap of bromide (Br⁻), the amount of Br⁻ is regulated, leading to high power conversion efficiency. As a result, MA-free perovskite solar cells achieve remarkable long-term stability and a PCE of 20.50%, which is one of the best results for MA-free PSCs. Moreover, the unencapsulated device retains about 80% of the original efficiencies after a 1000 h aging study. These results provide a feasible approach to enhance solar cell stability and performance simultaneously, paving the way for commercializing PSCs.     

Dopant-Free Polymer Hole Transport Materials for Highly Stable and Efficient CsPbI3 Perovskite Solar Cells

All-inorganic perovskite CsPbI₃ contains no volatile organic components and is a thermally stable photoactive material for wide-bandgap perovskite solar cells (PSCs); however, CsPbI₃ readily undergoes undesirable phase transitions due to the hygroscopic nature of the ionic dopants used in commonly used hole transport materials. In the current study, the popular donor material PM6 in organic solar cells is used as a hole transport layer (HTL). The benzodithiophene-based backbone-conjugated polymer requires no dopant and leads to a higher power conversion efficiency (PCE) than 2,2′,7,7′-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9′-spirobifluorene (Spiro-OMeTAD). Moreover, PM6 also shows priorities in hole mobility, hydrophobicity, cascade energy level alignment, and even defect passivation of perovskite films. With PM6 as the dopant-free HTL, the PSCs achieve a champion PCE of 18.27% with a competitive fill factor of 82.8%. Notably, the present PCE is based on the dopant-free HTL in CsPbI₃ PSCs reported thus far. The PSCs with PM6 as the HTL retain over 90% of the initial PCE stored in a glovebox filled with N₂ for 3000 h. In contrast, the PSCs with Spiro-OMeTAD as the HTL maintain ≈80% of the initial PCE under the same conditions.     

Perovskite Solar Cells with Inorganic Electron‐ and Hole‐Transport Layers Exhibiting Long‐Term (≈500 h) Stability at 85 °C under Continuous 1 Sun Illumination in Ambient Air

Despite the high power conversion efficiency (PCE) of perovskite solar cells (PSCs), poor long‐term stability is one of the main obstacles preventing their commercialization. Several approaches to enhance the stability of PSCs have been proposed. However, an accelerating stability test of PSCs at high temperature under the operating conditions in ambient air remains still to be demonstrated. Herein, interface‐engineered stable PSCs with inorganic charge‐transport layers are shown. The highly conductive Al‐doped ZnO films act as efficient electron‐transporting layers as well as dense passivation layers. This layer prevents underneath perovskite from moisture contact, evaporation of components, and reaction with a metal electrode. Finally, inverted‐type PSCs with inorganic charge‐transport layers exhibit a PCE of 18.45% and retain 86.7% of the initial efficiency for 500 h under continuous 1 Sun illumination at 85 °C in ambient air with electrical biases (at maximum power point tracking).     

Boosting efficiency and stability of perovskite solar cells with nickel phthalocyanine as a low-cost hole transporting layer material

The efficiency of perovskite solar cells(PSCs) has increased from around 4% to over 22% following a few years of intensive investigation. For most PSCs, organic materials such as 2,2',7,7'-tetrakis(N,Npdimethoxyphenylamino)-9,9'-spirobifluorene(spiro-OMeTAD) are used as the hole transporting materials(HTMs), which are thermally and chemically unstable and also expensive. Here, we explored nickel phthalocyanine(NiPc) as a stable and cost-effective HTM to replace the conventionally used spiroOMeTAD. Because of its high carrier mobility and proper band alignments, we achieved a PCE of 12.1% on NiPc based planar device with short-circuit current density(Jsc) of 17.64 mAcm~(-2), open circuit voltage(Voc) of 0.94 V, and fill factor(FF) of 73%, outperforming the planar device based on copper phthalocyanine(CuPc) that is an outstanding representative of metal phthalocyanines(MPcs) reported. Moreover,the device with NiPc shows much improved stability compared to that based on the conventional spiroOMeTAD as a result of NiPc's high stability. Photoluminescence(PL) and Impedance spectroscopy analysis results show that thermally deposited NiPc has good hole-extraction ability. Our results suggest that NiPc is a promising HTM for the large area, low cost and stable PSCs.     

Collaborative Passivation for Dual Charge Transporting Layers Based on 4-(chloromethyl)benzonitrile Additive toward Efficient and Stable Inverted Perovskite Solar Cells

Poor carrier transport capacity and numerous surface defects of charge transporting layers (CTLs), coupled with misalignment of energy levels between perovskites and CTLs, impact photoelectric conversion efficiency (PCE) of inverted perovskite solar cells (PSCs) profoundly. Herein, a collaborative passivation strategy is proposed based on 4-(chloromethyl) benzonitrile (CBN) as a solution additive for fabrication of both [6,6]-phenyl-C61-butyric acid methylester (PCBM) and poly(triarylamine) (PTAA) CTLs. This additive can improve wettability of PTAA and reduce the agglomeration of PCBM particles, which enhance the PCE and device stability of the PSCs. As a result, a PCE exceeding 20% with a remarkable short circuit current of 23.9 mA cm⁻², and an improved fill factor of 81% is obtained for the CBN- modified inverted PSCs. Devices maintain 80% and 70% of the initial PCE after storage under 30% and 85% humidity ambient conditions for 1000 h without encapsulation, as well as negligible light state PCE loss. This strategy demonstrates feasibility of the additive engineering to improve interfacial contact between the CTLs and perovskites for fabrication of efficient and stable inverted PSCs.     

Metal-Organic Framework Materials in Perovskite Solar Cells: Recent Advancements and Perspectives

Organic–inorganic hybrid perovskite solar cells (PSCs) are among the most promising candidates for the next generation of photovoltaic devices because of the significant increase in their power conversion efficiency (PCE) from less than 10% to 25.7% in past decade. The metal-organic framework (MOF) materials owing to their unique properties, such as large specific surface area, abundant binding sites, adjustable nanostructures, and synergistic effects, are used as additives or functional layers to enhance the device performance and long-term stability of PSCs. This review focuses on the recent advancements in the applications of MOFs as/in different functional layers of PSCs. The photovoltaic performance, impact, and advantages of MOF materials integrated into the perovskite absorber, electron transport layer, hole transport layer, and interfacial layer are reviewed. In addition, the applicability of MOFs to mitigate leakage of Pb²⁺ from halide perovskites and corresponding devices is discussed. This review concludes with the perspectives on further research directions for employing MOFs in PSCs.     

具有2D-EDAPbI4薄覆盖层的环境稳定的FAPbI3基钙钛矿太阳能电池（英文）

二维(2D)卤化铅钙钛矿材料是钙钛矿太阳能电池(PSC)中最有前途的吸光材料之一,具有优异的稳定性和缺陷钝化作用.然而,这些稳定的二维PSC的转换效率仍远远落后于三维钙钛矿电池.在本文中我们通过原位生长的方法将2D EDAPbI4层成功制备在3D FAPbI3层表面。这种合理设计的2D-3D钙钛矿薄膜分层结构可以明显提高电池的效率.另外,由于EDAPbI4层的高抗湿性和抑制迁移, 2D-3D电池器件显示出明显增强的长期稳定性,在200 h内一直保持初始转换效率,甚至在500 h后仍能保持其初始转化效率的90%.     

Graphdiyne: A Brilliant Hole Accumulator for Stable and Efficient Planar Perovskite Solar Cells

Traditional carbon materials have demonstrated immense potential in perovskite solar cells (PSCs) owing to their superior electrical properties and environmental stability. Graphdiyne (GDY), as an emerging carbon allotrope, features uniformly distributed pores, endless design flexibility, and unique electronic character compared with traditional carbon materials. Herein, graphdiyne is introduced into the upper part of the perovskite (CH₃NH₃PbI₃) layer by utilizing a GDY‐containing antisolvent during the one‐step synthesis of perovskite. Intriguingly, GDY plays an essential role in hole accumulation and transportation because of its higher Fermi level than perovskite. As a result, the automatic separation of photogenerated carriers inside the perovskite film is achieved. Furthermore, the Schottky barrier formed on the interface between perovskite and GDY guarantees the unidirectional hole transport from perovskite to GDY, thereby benefiting further extraction to the hole transport layer. Consequently, GDY‐modified perovskite‐based planar PSCs exhibit a boosted J_sc of 24.21 mA cm^?2 and up to 19.6% power conversion efficiency owing to the increased efficient light utilization and charge extraction. The device with GDY modification exhibits less than 10% shrinkage after a month in ambience. Overall, this work demonstrates an easy method for the utilization of GDY to boost the charge extraction and environmental stability in PSCs.     

Dopant‐Free Small‐Molecule Hole‐Transporting Material for Inverted Perovskite Solar Cells with Efficiency Exceeding 21%

Hole‐transporting materials (HTMs) play a critical role in realizing efficient and stable perovskite solar cells (PVSCs). Considering their capability of enabling PVSCs with good device reproducibility and long‐term stability, high‐performance dopant‐free small‐molecule HTMs (SM‐HTMs) are greatly desired. However, such dopant‐free SM‐HTMs are highly elusive, limiting the current record efficiencies of inverted PVSCs to around 19%. Here, two novel donor–acceptor‐type SM‐HTMs (MPA‐BTI and MPA‐BTTI) are devised, which synergistically integrate several design principles for high‐performance HTMs, and exhibit comparable optoelectronic properties but distinct molecular configuration and film properties. Consequently, the dopant‐free MPA‐BTTI‐based inverted PVSCs achieve a remarkable efficiency of 21.17% with negligible hysteresis and superior thermal stability and long‐term stability under illumination, which breaks the long‐time standing bottleneck in the development of dopant‐free SM‐HTMs for highly efficient inverted PVSCs. Such a breakthrough is attributed to the well‐aligned energy levels, appropriate hole mobility, and most importantly, the excellent film morphology of the MPA‐BTTI. The results underscore the effectiveness of the design tactics, providing a new avenue for developing high‐performance dopant‐free SM‐HTMs in PVSCs.