Effect of heavy metals and water content on the strength of magnesium phosphate cements

In this paper the mechanical properties of magnesium potassium phosphate cements used for the Stabilization/Solidification (S/S) of galvanic wastes were investigated. Surrogate wastes (metal nitrate dissolutions) were employed containing Cd, Cr(III), Cu, Ni, Pb or Zn at a concentration of 25 g dm⁻³ and different water-to-solid (W/S) ratios (0.3, 0.4, 0.5 and 0.6 dm³ kg⁻¹) have been employed. Cements were prepared by mixing hard burned magnesia of about 70% purity with potassium dihydrogen phosphate. Compressive strength and tensile strength of specimens were determined. In addition the volume of permeable voids was measured. It was found that when comparing pastes that the volume of permeable voids increases and mechanical strength decreases with the increase of water-to-solid ratio (W/S). Nevertheless pastes with the same material proportions containing different metals show different mechanical strength values. The hydration products were analyzed by XRD. With the increase of water content not previously reported hydration compound was detected: bobierrite.     

Influence of key cement chemical parameters on the properties of metakaolin blended cements

The use of metakaolin (MK) as a mineral admixture for cement and concrete is a well-documented practice. The properties of cement pastes and mortars containing MK have been investigated as a function of key cement chemical parameters recognized as potential activators of the MK. Rheological behavior, initial setting time and compressive strength development have been compared by varying the total sulfate content, the nature of the added calcium sulfate and the free lime content (in the form of portlandite) in the cement. The results obtained indicate that it exists a compromise for the ratio performance/consistency in term of sulfate content and nature. Concurrently, a small addition of portlandite improves the consistency of the properties investigated.     

Influence of limestone and anhydrite on the hydration of Portland cements

The addition of CaCO₃ and CaSO₄ to Portland cement clinker influences the hydration and the strength development. An increase of the CaSO₄ content accelerates alite reaction during the first days and results in the formation of more ettringite, thus in a higher early compressive strength. The late compressive strength is decreased in Portland cements containing higher quantities of CaSO₄. The reduced late compressive strength seems to be related to an increase of the S/Si and Ca/Si content in the C–S–H.The presence of calcite leads to the formation of hemicarbonate and monocarbonate thus indirectly to more ettringite. Only a relatively small quantity of calcite reacts to form monocarbonate or hemicarbonate in Portland cement. Although hemicarbonate is thermodynamically less stable than monocarbonate, hemicarbonate formation is kinetically favored. Monocarbonate is present only after 1 week and longer independent of the quantity of calcite available and the content of sulphate in the cement.     

Effect of cement type and limestone particle size on the durability of steam cured self-consolidating concrete

This paper describes a laboratory program to investigate the influence of cement and limestone filler (LF) particle size on the hardened properties and durability performance of steam cured self-consolidating concrete. In addition, the interplay between cement type and LF particle size was investigated. CSA (Canadian Standards Association) Type GU (General Use) and HE (High Early-strength) cements were used with 5% silica fume (SF) [1]. The water-to-cement ratio was 0.34. LF with two nominal particle sizes of 17 μm and 3 μm, which correspond to Blaine fineness of 475 and 1125 m²/kg, respectively, were used. In addition to fresh concrete properties, hardened properties including compressive strength, elastic modulus, ultrasonic pulse velocity and density were measured at 12 h and 16 h, and at 3, 7 and 28 days. Indicators of durability performance including rapid chloride permeability testing (RCPT), sulfate resistance, linear shrinkage, salt scaling resistance and freeze-thaw resistance were evaluated. The results showed that LF improved the 12 and 16-h strength with no influence on later age strength (i.e., 3–28 days). The linear shrinkage and RCPT decreased with the addition of LF. This reduction was linked to the production of calcium mono-carboaluminate. LF did not impact the sulfate resistance, salt scaling resistance or freeze-thaw resistance of concrete.