Hydrothermal liquefaction of spent coffee grounds in water medium for bio-oil production

Spent coffee grounds (SCG) were liquefied in hot-compressed water to produce crude bio-oil via hydrothermal liquefaction (HTL) in a 100 cm³ stainless-steel autoclave reactor in N₂ atmosphere. We investigated the effects of operating parameters such as retention times (5 min, 10 min, 15 min, 20 min and 25 min), reaction temperatures (200 °C, 225 °C, 250 °C, 275 °C and 300 °C), and water/feedstock mass ratios (5:1, 10:1, 15:1 and 20:1) and initial pressure of process gas (2.0 MPa and 0.5 MPa) on the yield and properties of the resulting crude bio-oil. The highest yield of the crude bio-oil (47.3% mass fraction) was obtained at conditions of 275 °C, 10 min retention time and water/feedstock mass ratio of 20:1 with an initial pressure of 2.0 MPa. The elemental analysis of the produced crude bio-oil revealed that the oil product had a higher heating value (HHV) of 31.0 MJ kg⁻¹, much higher than that of the raw material (20.2 MJ kg⁻¹). GC–MS and FT-IR measurements showed that the main volatile compounds in the crude bio-oil were long chain aliphatic acids and esters.     

Optimization study of sub/supercritical water liquefication of lignite: Fast liquefaction for high bio-oil yield

Sub/supercritical water liquefication (SCWL) is a water-based thermochemical technology as well as an environmentally friendly treatment by converting wet feedstock into bioenergy. In the present study, a systematic investigation of SCWL of lignite was carried out covering a temperature range between 320 and 440 °C when residence time increased from 5 min to 40 min. The highest bio-oil oil yield of 34.3% with solid residue of 52.7% was obtained at 440 °C for 5 min. Phenol derivatives, carboxylic acids, long chain hydrocarbons, ketones, and naphthalene were the main bio-oil composition through FTIR and GC-MS analysis. Gas yields and their exact compositions were also determined and CO₂ was the dominate gas product but the percentage of CH₄ became significant at severe SCWL conditions. A conclusion was drawn that fast liquefaction (e.g. 5 min) at relative higher temperature (e.g. 400 °C) which avoid excessive gasification and repolymerization reactions was an optimization strategy for high yield bio-oil production from SCWL of lignite.     

Hydrothermal liquefaction of macroalgae: Influence of zeolites based catalyst on products

Hydrothermal liquefaction (HTL) of Ulva prolifera macroalgae (UP) was carried out in the presence of three zeolites based catalysts (ZSM-5, Y-Zeolite and Mordenite) with the different weight percentage (10–20 wt%) at 260–300 °C for 15–45 min. A comparison between non-catalytic and catalytic behavior of ZSM-5, Y-Zeolite, and Mordenite in the conversion of Ulva prolifera showed that is affected by properties of zeolites. Maximum bio-oil yield for non-catalytic liquefaction was 16.6 wt% at 280 °C for 15 min. The bio-oil yield increased to 29.3 wt% with ZSM-5 catalyst (15.0 wt%) at 280 °C. The chemical components and functional groups present in the bio-oils are identified by GC-MS, FT-IR, ¹H-NMR, and elemental analysis techniques. Higher heating value (HHV) of bio-oil (32.2–34.8 MJ/kg) obtained when catalyst was used compared to the non-catalytic reaction (21.2 MJ/kg). The higher de-oxygenation occurred in the case of ZSM-5 catalytic liquefaction reaction compared to the other catalyst such as Y-zeolite and mordenite. The maximum percentage of the aromatic proton was observed in bio-oil of ZSM-5 (29.7%) catalyzed reaction and minimum (1.4%) was observed in the non-catalyst reaction bio-oil. The use of zeolites catalyst during the liquefaction, the oxygen content in the bio-oil reduced to 17.7%. Aqueous phase analysis exposed that presence of valuables nutrients.     

Comparison of pyrolysis and hydrothermal liquefaction of Chlamydomonas reinhardtii. Growth studies on the recovered hydrothermal aqueous phase

The production of bio-oil by pyrolysis with a high heating rate (500 K s⁻¹) and hydrothermal liquefaction (HTL) of Chlamydomonas reinhardtii was compared. HTL led to bio-oil yield decreasing from 67% mass fraction at 220 °C to 59% mass fraction at 310 °C whereas the bio-oil yield increased from 53% mass fraction at 400 °C to 60% mass fraction at 550 °C for pyrolysis. Energy ratios (energy produced in the form of bio-oil divided by the energy content of the initial microalgae) between 66% at 220 °C and 90% at 310 °C in HTL were obtained whereas it was in the range 73–83% at 400–550 °C for pyrolysis. The Higher Heating Value of the HTL bio-oil was increasing with the temperature while it was constant for pyrolysis. Microalgae cultivation in aqueous phase produced by HTL was also investigated and showed promising results.     

Optimisation of bio-oil production by hydrothermal liquefaction of agro-industrial residues: Blackcurrant pomace (Ribes nigrum L.) as an example

This work reports bio-oil production by hydrothermal liquefaction of blackcurrant pomace (Ribes nigrum L.), a fruit residue obtained after berry pressing. The bio-oil has a higher heating value of 35.9 MJ kg⁻¹ and low ash content, which makes it suitable for energy applications. We report the influence of process parameters on yields and carbon distribution between products: temperature (563–608 K), holding time (0–240 min), mass fraction of dry biomass in the slurry (0.05–0.29), and initial pH (3.1–12.8) by adding sodium hydroxide (NaOH). Depending on the experiments, the bio-oil accounts for at least 24% mass fraction of the initial dry biomass, while char yields ranges from 24 to 40%. A temperature of 583 K enhances the bio-oil yield, up to 30%, while holding time does not have a significant influence on the results. Increasing biomass concentrations decreases bio-oil yields from 29% to 24%. Adding sodium hydroxide decreases the char yield from 35% at pH = 3.1 (without NaOH) to 24% at pH = 12.8. It also increases the bio-oil yield and carbon transfer to the aqueous phase. Thermogravimetric analysis shows that a 43% mass fraction of the bio-oil boils in the medium naphtha petroleum fraction range. The bio-oil is highly acidic and unsaturated, and its dynamic viscosity is high (1.7 Pa s at 298 K), underlining the need for further upgrading before any use for fuel applications.     

Effect of aluminium sulphate-catalysed hydrolysis process on furfural yield and cellulose degradation of Cannabis sativa L. shives

Commercially, furfural is produced from pentosan-rich biomass using mineral acids as homogeneous catalysts. This study investigated a novel hydrolysis method that allows to obtain furfural from hemp shives with high yield and also to preserve the cellulose in the remaining biomass for other bioconversion processes. To date, hemp shives have not been investigated for furfural production. Cannabis sativa L. (“Bialobrzeskie” variety) shives were used as a feedstock due to the high content of pentosan (17.6% of oven-dried biomass). It means that the theoretically possible amount of furfural was 12.8% of oven-dried hemp shives. The effect of temperature (140–180 °C), the amount of catalyst (3–7% of oven-dried biomass) and the treatment time (10–90 min) on the furfural formation were studied. Whereas, the effect of the same temperature and the amount of catalyst on the changes of lignocellulose were studied after 90 min treatment time. Al₂(SO₄)₃*18H₂O was used as a catalyst for the conversion of C5-sugars to furfural. To show the catalytic properties of Al₂(SO₄)₃*18H₂O, autocatalysis was performed as a reference process using the same parameters. The highest yield of furfural, 73.7% of the theoretical yield, was obtained at 180 °C, 5% Al₂(SO₄)₃*18H₂O of oven-dried mass and 90 min. From the biorefinery perspective, the optimal hydrolysis parameters were 160 °C, 5% Al₂(SO₄)₃*18H₂O of oven-dried mass and 90 min. With these parameters, the yield of furfural was 62.7% of the theoretical yield, 99.2% of hemicelluloses were removed and 95.8% of cellulose was preserved and slightly depolymerized.     

Bio-oil fractionation by temperature-swing extraction: Principle and application

Bio-oils produced by direct thermal liquefaction often contain heavy components that hinder their utilization as a liquefaction medium. This paper reports a new approach to fractionate the liquefaction bio-oil into a light and a heavy fraction based on solvent extraction and temperature-swing regeneration. This approach is based on hot extraction (T ∼ 70 °C) of the light fraction of the oil with a suitable extraction solvent followed by cold (T ∼ 25 °C) de-mixing of the light fraction and the extraction solvent. In this paper, we (i) illustrate the selection of the extraction solvent and define the solvent properties required, (ii) demonstrate the potential of multistage extraction/regeneration for the bio-oil produced by direct thermal liquefaction, (iii) extend the concept to fractionate a petroleum crude oil, (iv) discuss the theoretical basis of the fractionation using polymer solution theory and, finally, (v) show a low energy requirement of the extraction process by means of process simulation, i.e., an equivalent of ∼1% of the biomass intake.     

Comparative studies of thermochemical liquefaction characteristics of microalgae using different organic solvents

The effect of different organic solvents, such as methanol, ethanol and 1,4-dioxane, on thermochemical liquefaction characteristics of Spirulina (a kind of high-protein microalgae) was systematically studied. The liquefaction experiments were conducted in a 1000 mL autoclave at different temperatures from 573 to 653 K with a fixed solid/liquid ratio. Liquefaction of Spirulina processed in methanol and ethanol favored the conversion rate and bio-oil yield compared with that in 1,4-dioxane solvent. The bio-oil generated in methanol contained higher C and H concentrations but a lower O content, resulting in a higher caloric value (39.83 MJ/kg). The results of FT-IR (Fourier Transform Infrared Spectroscopy) and GC-MS (Gas Chromatography-Mass Spectroscopy) analyses indicated that the compositions of bio-oil products were greatly affected by the type of solvent used for the liquefaction process. The major component of bio-oil produced with methanol was hexadecanoic acid methyl ester (C₁₇H₃₄O₂, 35.53%). However, ethanol favored the formation of hexadecanoic acid ethyl ester (C₁₈H₃₆O₂, 26.27%). When Spirulina were operated with 1,4-dioxane, the bio-oil was dominated by hexadecanenitrile (C₁₆H₃₁N, 22.7%). The presence of methanol and ethanol might promote the formation of esters. Low-boiling-points compounds with phenol ring structure or heterocyclics can be generated when 1,4-dioxane was employed as solvent.     

Bio-oil catalytic reforming without steam addition: Application to hydrogen production and studies on its mechanism

A novel process for hydrogen production via bio-oil catalytic reforming without steam addition was proposed. The liquid feedstock was a distillation fraction from crude bio-oil molecular distillation. The fraction obtained was enriched with the low-molecular-weight organics (acids, aldehydes, and ketones), and contained nearly all of the water from crude bio-oil. The highest catalytic performance, with a carbon conversion of 95% and a H₂ yield of 135 mg g⁻¹ organics, was obtained by processing the distillate over Ni/Al₂O₃ catalyst at 700 °C. The steam involved in the reforming reaction was derived entirely from the water in the crude bio-oil. The fresh and spent catalysts were characterized by N₂-physisorption, thermogravimetric analysis, and high-resolution transmission electron microscopy. To further understand the reaction mechanisms, symmetric density functional theory calculations for decomposition were performed on four model compounds in bio-oil (acetic acid, hydroxyacetone, furfural, and phenol) over the Ni(111) surface. In addition, the decomposition of H₂O∗ to OH∗ and O∗ and their subsequent steam reforming reactions with carbon precursors (CH∗ and CH₃C∗) were also examined.     

Characterization of bio-oil and its sub-fractions from pyrolysis of Scenedesmus dimorphus

In the present study, microalgae Scenedesmus dimorphus was reported for pyrolysis in a fixed-bed reactor to determine the effects of temperature on products yield and the chemical compositions of the liquid and solid products. Experiments were carried out at a temperature range of 300–600 °C with heating rate of 40 °C/min and nitrogen flow rate of 100 ml/min. The yield of bio-oil was found to be maximum (39.6%) at the temperature of 500 °C and was further fractionated into n-hexane, toluene, ethyl acetate and methanol sub-fractions by using liquid column chromatography. Various characteristics of bio-oil and its sub-fractions were determined by ¹H NMR, FTIR and GC–MS. The biochar produced as a co-product can be a potential soil amendment with multiple benefits including soil fertility and C-sequestration. The present investigation suggests the suitability of Scenedesmus dimorphus as a potential feedstock for exploitation of energy and biomaterials through pyrolytic conversion.     

Bio-oil production from hydrothermal liquefaction of waste Cyanophyta biomass: Influence of process variables and their interactions on the product distributions

Hydrothermal liquefaction (HTL) of waste Cyanophyta biomass at different temperatures (factor A, 260–420 °C), times (factor B, 5–75 min) and algae/water (a/w) ratios (factor C, 0.02–0.3) by single reaction condition and Response Surface Method (RSM) experiments was investigated. By single reaction condition runs, maximum total bio-oil yield (29.24%) was obtained at 350 °C, 60 min and 0.25 a/w ratio. Maximum bio-oil HHV of 40.04 MJ/kg and energy recovery of 51.09% was achieved at 350 °C, 30 min, 0.1 a/w ratio and 350 °C, 60 min, 0.25 a/w ratio, respectively. RSM results indicate that effect of AB interaction was significant on light bio-oil yield. Both AC and AB had more remarkable influence than BC on heavy bio-oil yield and aqueous total organic carbon (TOC) recovery whereas BC was noticeable on ammonia nitrogen (NH₃N) recovery in aqueous products. By model-based optimization of highest bio-oil yield, the highest bio-oil yield reached 31.79%, increasing by 8.72% after RSM optimization, and light and heavy bio-oil yield was 17.44% and 14.35%, respectively. Long-chain alkanes, alkenes, ketones, fatty acids, phenols, benzenes, amides, naphthalenes were the main components in light bio-oil. Some alcohols, phenols and aromatics were primarily found in heavy bio-oil. Solid residue after HTL consisted of numerous microparticles (～5 μm) observed by Scanning Electron Microscopy (SEM). Energy Dispersive Spectrometer (EDS) analysis shows these particles primarily contained C, O, Mg, P and microelements, derived from Cyanophyta cells.     

Pyrolysis of Alternanthera philoxeroides (alligator weed): Effect of pyrolysis parameter on product yield and characterization of liquid product and bio char

In the present work, fast pyrolysis of Alternanthera philoxeroides was evaluated with a focus to study the chemical and physical characteristics of bio-oil produced and to determine its practicability as a transportation fuel. Pyrolysis of A.philoxeroides was conducted inside a semi batch quartz glass reactor to determine the effect of different operating conditions on the pyrolysis product yield. The thermal pyrolysis of A. philoxeroides were performed at a temperature range from 350 to 550 °C at a constant heating rate of 25 °C/min & under nitrogen atmosphere at a flow rate of 0.1 L/min, which yielded a total 40.10 wt.% of bio-oil at 450 °C. Later, some more sets of experiments were also performed to see the effect on pyrolysis product yield with change in operating conditions like varying heating rates (50 °C/min, 75 °C/min & 100 °C/min) and different flow rates of nitrogen (0.2, 0.3, 0.4 & 0.5 L/min). The yield of bio-oil during different heating rate (25, 50, 75 and 100 °C/min) was found to be more (43.15 wt.%) at a constant heating rate of 50 °C/min with 0.2 L/min N₂ gas flow rate and at a fixed pyrolysis temperature of 450 °C. The High Heating Value (HHV) value of bio-oil (8.88 MJ/kg) was very less due to presence of oxygen in the biomass. However, the high heating value of bio-char (20.41 MJ/kg) was more, and has the potential to be used as a solid fuel. The thermal degradation of A. philoxeroides was studied in TGA under inert atmosphere. The characterization of bio-oil was done by elemental analyser (CHNS/O analyser), FT-IR, & GC/MS. The char was characterized by elemental analyser (CHNS/O analysis), SEM, BET and FT-IR techniques. The chemical characterization showed that the bio-oil could be used as a transportation fuel if upgraded or blended with other fuels. The bio-oil can also be used as feedstock for different chemicals. The bio-char obtained from A. philoxeroides can be used for adsorption purposes because of its high surface area.     

Studies on catalytic pyrolysis of empty fruit bunch (EFB) using Taguchi's L9 Orthogonal Array

This paper investigates the effects of four reaction parameters that include type of catalyst, catalyst loading, reaction temperature and nitrogen gas flowrate on the liquid (bio-oil) yield from the catalytic pyrolysis of Empty Fruit Bunch (EFB). The experimental design is based on Taguchi's L9 Orthogonal Array in which the reaction parameters are varied at three levels. The maximum liquid yield is predicted based on systematic experimental runs, and is found to be at 5 wt-% of H-Y catalyst, 500 °C and at nitrogen flowrate of 100 ml min⁻¹. The predicted maximum liquid yield is validated with an experimental run at the corresponding predicted conditions. The bio-oil produced at the optimum reaction condition is characterized and compared with known bio-oil standards in the literature.     

Catalytic supercritical water gasification of aqueous phase directly derived from microalgae hydrothermal liquefaction

Microalgae (N. chlorella) hydrothermal liquefaction (HTL) was conducted at 320 °C for 30 min to directly obtain original aqueous phase with a solvent-free separation method, and then the supercritical water gasification (SCWG) experiments of the aqueous phase were performed at 450 and 500 °C for 10 min with different catalysts (i.e., Pt-Pd/C, Ru/C, Pd/C, Na₂CO₃ and NaOH). The results show that increasing temperature from 450 to 500 °C could improve H₂ yield and TGE (total gasification efficiency), CGE (carbon gasification efficiency), HGE (hydrogen gasification efficiency), TOC (total organic carbon) removal efficiency and tar removal efficiency. The catalytic activity order in improving the H₂ yield was NaOH > Na₂CO₃ > None > Pd/C > Pt-Pd/C > Ru/C. Ru/C produced the highest CH₄ mole fraction, TGE, CGE, TOC removal efficiency and tar removal efficiency, while NaOH led to the highest H₂ mole fraction, H₂ yield and HGE at 500 °C. Increasing temperature and adding proper catalyst could remarkably improve the SCWG process above, but some N-containing compounds were difficult to be gasified. This information is valuable for guiding the treatment of the aqueous phase derived from microalgae HTL.     

Supercritical water gasification of timothy grass as an energy crop in the presence of alkali carbonate and hydroxide catalysts

This study is focused on identifying the candidature of timothy grass as an energy crop for hydrogen-rich syngas production through supercritical water gasification. Timothy grass was gasified in supercritical water to investigate the impacts of temperature (450–650 °C), biomass-to-water ratio (1:4 and 1:8) and reaction time (15–45 min) in the pressure range of 23–25 MPa. The impacts of carbonate catalysts (e.g., Na₂CO₃ and K₂CO₃) and hydroxide catalysts (e.g., NaOH and KOH) at variable mass fractions (1–3%) were examined to maximize hydrogen yields. In the non-catalytic gasification of timothy grass, highest hydrogen (5.15 mol kg⁻¹) and total gas yields (17.2 mol kg⁻¹) with greater carbon gasification efficiency (33%) and lower heating value (2.21 MJ m⁻³) of the gas products were obtained at 650 °C with 1:8 biomass-to-water ratio for 45 min. However, KOH at 3% mass fraction maximized hydrogen and total gas yields up to 8.91 and 30.6 mol kg⁻¹, respectively. Nevertheless, NaOH demonstrated highest carbon gasification efficiency (61.3%) and enhanced lower heating value of the gas products (4.68 MJ m⁻³). Timothy grass biochars were characterized through Fourier transform infrared spectroscopy, Raman spectroscopy and scanning electron microscopy to understand the behavior of the feedstock to rising temperature and reaction time. The overall findings suggest that timothy grass is a promising feedstock for hydrogen production via supercritical water gasification.     

Optimization of various pretreatments condition of kenaf core (Hibiscus cannabinus) fibre for sugar production: Effect of chemical compositions of pretreated fibre on enzymatic hydrolysability

In this work, the effects of various pretreatments’ parameters on kenaf core fibre were analyzed statistically and optimized using Response Surface Methodology based on the total glucose yield. The chemical compositions of the pretreated fibres were examined to discuss the effect of pretreatment on the fibre hydrolysability comprehensively. The results showed that estimation model for each pretreatment of kenaf core fibre were polynomial equations. The optimum conditions for water, acid and alkali pretreatments were 170 °C for 45 min, 120 °C for 90 min in 2.0% H₂SO₄ solution and 140 °C for 60 min in 3.0% NaOH solution, respectively. Among the three pretreatments, water pretreatment achieved the highest total glucose yield (25.5%), followed by acid (20.0%) and alkali (18.2%) pretreatments. Based on chemical compositions analysis, both water and acid pretreatments were capable of eliminating almost 100% of hemicellulose with negligible removal of lignin while the alkali pretreatment removed both the lignin and hemicellulose more than 60%. This result revealed that the removal of hemicellulose showed greater influential in enhancing the enzymatic accessibility and hence, hydrolysability of kenaf core fibre.     

Production and detailed characterization of bio-oil from fast pyrolysis of palm kernel shell

Bio-oil has been produced from palm kernel shell in a fluidized bed reactor. The process conditions were optimized and the detailed characteristics of bio-oil were carried out. The higher feeding rate and higher gas flow rate attributed to higher bio-oil yield. The maximum mass fraction of biomass (57%) converted to bio-oil at 550 °C when 2 L min⁻¹ of gas and 10 g min⁻¹ of biomass were fed. The bio-oil produced up to 500 °C existed in two distinct phases, while it formed one homogeneous phase when it was produced above 500 °C. The higher heating value of bio-oil produced at 550 °C was found to be 23.48 MJ kg⁻¹. As GC–MS data shows, the area ratio of phenol is the maximum among the area ratio of identified compounds in 550 °C bio-oil. The UV–Fluorescence absorption, which is the indication of aromatic content, is also the highest in 550 °C bio-oil.     

Utilization possibilities of palm shell as a source of biomass energy in Malaysia by producing bio-oil in pyrolysis process

Agriculture residues such as palm shell are one of the biomass categories that can be utilized for conversion to bio-oil by using pyrolysis process. Palm shells were pyrolyzed in a fluidized-bed reactor at 400, 500, 600, 700 and 800 °C with N₂ as carrier gas at flow rate 1, 2, 3, 4 and 5 L/min. The objective of the present work is to determine the effects of temperature, flow rate of N₂, particle size and reaction time on the optimization of production of renewable bio-oil from palm shell. According to this study the maximum yield of bio-oil (47.3 wt%) can be obtained, working at the medium level for the operation temperature (500 °C) and 2 L/min of N₂ flow rate at 60 min reaction time. Temperature is the most important factor, having a significant positive effect on yield product of bio-oil. The oil was characterized by Fourier Transform infra-red (FT-IR) spectroscopy and gas chromatography/mass spectrometry (GC-MS) techniques.     

Improvement of gaseous bioenergy production from spent coffee grounds Co-digestion with pulp wastewater by physical/chemical pretreatments

Two steps of hydrolysis and anaerobic biogas production processes was investigated in this study. In the first step, subcritical water (SBW) hydrolysis and chemical (acid/alkali) pretreatments were carried out to enhance hydrolysis efficiency by obtaining and analyzing the total volatile fatty acids (TVFA), chemical oxygen demand (COD), and total sugar productions from spent coffee grounds (SCG) hydrolysate. The subcritical water (SBW) hydrolysis under the condition of temperature 150 °C for 30 min can greatly improve the organic matter breakdown and reached the COD concentration of 1010 g/L which was 30% higher than the untreated raw SCG. For chemical pretreatments, it was found that the alkaline hydrolysis of SCG resulted in the greatest total sugar concentration of 181 g/L whereas the operation conditions were 2.0 M NaOH at 60 °C for 1 h. The peak of TVFA concentration 3725 mg/L was found at the acid hydrolysis of SCG with 1.0 M H₂SO₄ acid, 60 °C for 1 h. The optimal biomethane yield of 115 mL/g COD was obtained when 1.0 M H₂SO₄ acid hydrolysate co-digestion with pulp wastewater which increase methane yield production 8 times of raw pulp wastewater. The pretreatment process was confirmed in this study can significant improve the converting of the biowastes to bioenergy efficiency.     

Optimization and characterization studies on bio-oil production from palm shell by pyrolysis using response surface methodology

In this work palm shell waste was pyrolyzed to produces bio-oil. The effects of several parameters on the pyrolysis efficiency were tested to identify the optimal bio-oil production conditions. The tested parameters include temperature, N₂ flow rate, feed-stock particle size, and reaction time. The experiments were conducted using a fix-bed reactor. The efficient response surface methodology (RSM), with a central composite design (CCD), were used for modeling and optimization the process parameters. The results showed that the second-order polynomial equation explains adequately the non-linear nature of the modeled response. An R² value of 0.9337 indicates a sufficient adjustment of the model with the experimental data. The optimal conditions found to be at the temperature of 500 °C, N₂ flow rate of 2 L/min, particle size of 2 mm and reaction time of 60 min and yield of bio-oil was approximately obtained 46.4 wt %. In addition, Fourier Transform infra-red (FT-IR) spectroscopy and gas chromatography/mass spectrometry (GC-MS) were used to characterize the gained bio-oil under the optimum condition.