A green catalyst for biodiesel production from jatropha oil: Optimization study

In this study, a simple and solvent-free method was used to prepare sulfated zirconia-alumina (SZA) catalyst. Its catalytic activity was subsequently investigated for the transesterification of Jatropha curcas L. oil to fatty acid methyl ester (FAME). The effects of catalyst preparation parameters on the yield of FAME were investigated using Design of Experiment (DOE). Results revealed that calcination temperature has a quadratic effect while calcination duration has a linear effect on the yield of FAME. Apart from that, interaction between both variables was also found to significantly affect the yield of FAME. At optimum condition; calcination temperature and calcination duration at 490 °C and 4 h, respectively, an optimum FAME yield of 78.2 wt% was obtained. Characterization with XRD, IR and BET were then used to verify the characteristic of SZA catalyst with those prepared using well established method and also to describe the catalyst characteristic with its activity.     

Biodiesel production from mixed soybean oil and rapeseed oil

The biodiesel (fatty acid methyl esters, FAME) was prepared by transesterification of the mixed oil (soybean oil and rapeseed oil) with sodium hydroxide (NaOH) as catalyst. The effects of mole ratio of methanol to oil, reaction temperature, catalyst amount and reaction time on the yield were studied. In order to decrease the operational temperature, a co-solvent (hexane) was added into the reactants and the conversion efficiency of the reaction was improved. The optimal reaction conditions were obtained by this experiment: methanol/oil mole ratio 5.0:1, reaction temperature 55 °C, catalyst amount 0.8 wt.% and reaction time 2.0 h. Under the optimum conditions, a 94% yield of methyl esters was reached ∼94%. The structure of the biodiesel was characterized by FT-IR spectroscopy. The sulfur content of biodiesel was determined by Inductively Coupled Plasma emission spectrometer (ICP), and the satisfied result was obtained. The properties of obtained biodiesel from mixed oil are close to commercial diesel fuel and is rated as a realistic fuel as an alternative to diesel. Production of biodiesel has positive impact on the utilization of agricultural and forestry products.     

Characterization and transesterification of Iranian bitter almond oil for biodiesel production

In the present work the production of biodiesel using bitter almond oil (BAO) in a potassium hydroxide catalyzed transesterification reaction was investigated. The BAO was obtained from resources available in Iran and its physical and chemical properties including iodine value, acid value, density, kinematic viscosity, fatty acid composition and mean molecular weight were specified. The low acid value of BAO (0.24 mg KOH/g) indicated that the pretreatment of raw oil with acid was not required. The fatty acid content analysis confirmed that the contribution of unsaturated fatty acids in the BAO is high (84.7 wt.%). Effect of different parameters including methanol to oil molar ratio (3–11 mol/mol), potassium hydroxide concentration (0.1–1.7% w/w) and reaction temperature (30–70 °C) on the production of biodiesel were investigated. The results indicated that these parameters were important factors affecting the tranesterification reaction. The fuel properties of biodiesel including iodine value, acid value, density, kinematic viscosity, saponification value, cetane number, flash point, cloud point, pour point and distillation characteristics were measured. The properties were compared with those of petroleum diesel, EN 14214 and ASTM 6751 biodiesel standards and an acceptable agreement was observed.     

Preparation, characterization and application of heterogeneous solid base catalyst for biodiesel production from soybean oil

A solid base catalyst was prepared by neodymium oxide loaded with potassium hydroxide and investigated for transesterification of soybean oil with methanol to biodiesel. After loading KOH of 30 wt.% on neodymium oxide followed by calcination at 600 °C, the catalyst gave the highest basicity and the best catalytic activity for this reaction. The obtained catalyst was characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), Thermogravimetric analysis (TGA), N₂ adsorption-desorption measurements and the Hammett indicator method. The catalyst has longer lifetime and maintained sustained activity after being used for five times, and were noncorrosive and environmentally benign. The separate effects of the molar ratio of methanol to oil, reaction temperature, mass ratio of catalyst to oil and reaction time were investigated. The experimental results showed that a 14:1 M ratio of methanol to oil, addition of 6.0% catalyst, 60 °C reaction temperature and 1.5 h reaction time gave the best results and the biodiesel yield of 92.41% was achieved. The properties of obtained biodiesel are close to commercial diesel fuel and is rated as a realistic fuel as an alternative to diesel.     

Alkaline catalyzed biodiesel production from moringa oleifera oil with optimized production parameters

The utilization of non-edible feedstock such as moringa oleifera for biodiesel production attracts much attention owing to the issue with regards to avoiding a threat to food supplies. In this study, the optimization of biodiesel production parameters for moringa oleifera oil was carried out. The free fatty acid value of moringa oil was found to be 0.6%, rendering the one step alkaline transesterification method for converting moringa fatty acids to their methyl esters possible. The optimum production parameters: catalyst amount, alcohol amount, temperature, agitation speed and reaction time were determined experimentally and found to be: 1.0 wt% catalyst amount, 30 wt% methanol amount, 60 °C reaction temperature, 400 rpm agitation rate and 60 min reaction time. With these optimal conditions the conversion efficiency was 82%. The properties of the moringa biodiesel that was produced were observed to fall within the recommended international biodiesel standards. However, moringa biodiesel showed high values of cloud and pour points of 10 °C and 3 °C respectively, which present a problem as regards use in cold temperatures.     

Manufacturing of zeolite based catalyst from zeolite tuft for biodiesel production from waste sunflower oil

In the present work, zeolite based catalyst was prepared from zeolite tuft by impregnation methods. The zeolite tuft was initially treated with hydrochloric acid (16%) and then several KOH/zeolite catalysts were prepared by impregnation in KOH solutions. Various solutions of KOH with different molarities (1–6 M) were used. Further modification for the catalyst was performed by a 2nd step impregnation treatment by heating and stirring the KOH/zeolite to 80 °C for 4 h. The zeolite tuft and the prepared catalysts were characterized by several analytical techniques in order to explore their physicochemical properties. These tests include: X-Ray Fluorescence (XRF), Scanning Electron Microscopy (SEM), Zero point of Charge (PHzpc), Fourier Transform Infrared (FT-IR), Energy-dispersive X-Ray analysis (EDX) and X-Ray Diffraction (XRD). The catalysts were then used for transesterification of waste sunflower vegetable oil in order to produce biodiesel. Among the different catalysts prepared, the 1–4M KOH/TZT catalyst provided the maximum biodiesel yield of 96.7% at 50 °C reaction temperature, methanol to oil molar ratio of 11.5:1, agitation speed of 800 rpm, 335 μm catalyst particle size and 2 h reaction time. The physicochemical properties of the produced biodiesel comply with the EN and ASTM standard specifications.     

Optimization of biodiesel production from camelina oil using orthogonal experiment

Camelina oil is a low-cost feedstock for biodiesel production that has received a great deal of attention in recent years. This paper describes an optimization study on the production of biodiesel from camelina seed oil using alkaline transesterification. The optimization was based on sixteen well-planned orthogonal experiments (OA₁₆ matrix). Four main process conditions in the transesterification reaction for obtaining the maximum biodiesel production yield (i.e. methanol quantity, reaction time, reaction temperature and catalyst concentration) were investigated. It was found that the order of significant factors for biodiesel production is catalyst concentration > reaction time > reaction temperature > methanol to oil ratio. Based on the results of the range analysis and analysis of variance (ANOVA), the maximum biodiesel yield was found at a molar ratio of methanol to oil of 8:1, a reaction time of 70 min, a reaction temperature of 50 °C, and a catalyst concentration of 1 wt.%. The product and FAME yields of biodiesel under optimal conditions reached 95.8% and 98.4%, respectively. The properties of the optimized biodiesel, including density, kinematic viscosity, acid value, etc., were determined and compared with those produced from other oil feedstocks. The optimized biodiesel from camelina oil meets the relevant ASTM D6571 and EN 14214 biodiesel standards and can be used as a qualified fuel for diesel engines.     

Effect of incompletely converted soybean oil on biodiesel quality

Presence of fully converted monoalkyl esters is the major requirement in quality biodiesel. Due to high associated costs with testing and widespread production of biodiesel not only in commercial scale but also in small scale, there is a high propensity of substandard biodiesel entering the market and being used in compression ignition engines. Due to this reason, it is important to understand how low grade biodiesel with a lower methyl ester conversion affects the parameters of quality standards and as a result, engine performance and durability. In this paper, the performance of fatty acid methyl esters with different proportions of unconverted triglycerides has been evaluated. The study has comprehensively evaluated the effect of unconverted triglycerides on flash point, water and sediment, kinematic viscosity, sulfur content, sulfated ash, copper strip corrosion, cetane number, cloud point, carbon residue, acid number, free glycerin, total glycerin, phosphorus content and distillation temperature.     

Combustion and performance evaluation of a diesel engine fueled with biodiesel produced from soybean crude oil

In this study, the biodiesel produced from soybean crude oil was prepared by a method of alkaline-catalyzed transesterification. The important properties of biodiesel were compared with those of diesel. Diesel and biodiesel were used as fuels in the compression ignition engine, and its performance, emissions and combustion characteristics of the engine were analyzed. The results showed that biodiesel exhibited the similar combustion stages to that of diesel, however, biodiesel showed an earlier start of combustion. At lower engine loads, the peak cylinder pressure, the peak rate of pressure rise and the peak of heat release rate during premixed combustion phase were higher for biodiesel than for diesel. At higher engine loads, the peak cylinder pressure of biodiesel was almost similar to that of diesel, but the peak rate of pressure rise and the peak of heat release rate were lower for biodiesel. The power output of biodiesel was almost identical with that of diesel. The brake specific fuel consumption was higher for biodiesel due to its lower heating value. Biodiesel provided significant reduction in CO, HC, NO_x and smoke under speed characteristic at full engine load. Based on this study, biodiesel can be used as a substitute for diesel in diesel engine.     

Castor oil transesterification reaction: A kinetic study and optimization of parameters

In this paper, parameters affecting castor oil transesterification reaction were investigated. Applying four basic catalysts including NaOCH₃, NaOH, KOCH₃ and KOH the best one with maximum biodiesel yield was identified. Using Taguchi method consisting four parameters and three levels, the best experimental conditions were determined. Reaction temperature (25, 65 and 80 °C), mixing intensity (250, 400 and 600 rpm), alcohol/oil ratio (4:1, 6:1 and 8:1) and catalyst concentration (0.25, 0.35 and 0.5%) were selected as experimental parameters. It was concluded that reaction temperature and mixing intensity can be optimized. Using the optimum results, we proposed a kinetic model which resulted in establishing an equation for the beginning rate of transesterification reaction. Furthermore, applying ASTM D 976 correlation, minimum cetane number of produced biodiesel was determined as 37.1.     

Microbial oil production from thermophile cyanobacteria for biodiesel production

Compared to lipid extraction from algae, little work has been performed for cyanobacteria. In this article it is aimed to show high lipid accumulation potential of Synechococcus sp., Cyanobacterium aponinum and Phormidium sp. cells in BG-11 medium. Four different pH values (6–9) and NaNO₃ (0.25, 0.5, 1.0, 1.5 g/L) concentrations were examined at different incubation days to discover the highest lipid accumulation. The maximum lipid content could be achieved in the medium containing 0.25 g/L NaNO₃ at pH 7 for Synechococcus sp., pH 8 for C. aponinum and pH 9 for Phormidium sp. after 15 days. The maximum lipid contents and C16 and C18 methyl ester yields were measured as 42.8% and 46.9% for Synechococcus sp., 45.0% and 67.7% for C. aponinum, 38.2% and 90.6% for Phormidium sp. The saturated compounds were 74.5%, 77.9%, 84.7% for Synechococcus sp., C. aponinum and Phormidium sp., respectively. These crude lipids could be promising feedstock for biodiesel production.     

Utilization of waste freshwater mussel shell as an economic catalyst for biodiesel production

An economic and environmentally friendly catalyst derived from waste freshwater mussel shell (FMS) was prepared by a calcination-impregnation-activation method, and it was applied in transesterification of Chinese tallow oil. The as-prepared catalyst exhibits a “honeycomb” -like structure with a specific surface area of 23.2 m² g⁻¹. The newly formed CaO crystals are major active phase of the catalyst. The optimal calcination and activity temperature are 900 °C and 600 °C, respectively. When the reaction is carried out at 70 °C with a methanol/oil molar ratio of 12:1, a catalyst concentration of 5% and a reaction time of 1.5 h, the FMS-catalyst is active for 7 reaction cycles, with the biodiesel yield above 90%. The experimental results indicate that the FMS can be used as an economic catalyst for the biodiesel production.     

Catalytic production of biodiesel from soy-bean oil, used frying oil and tallow

Three fatty materials, soy-bean oil, used frying oil and tallow, were transformed into two different types of biodiesel, by transesterification and amidation reactions with methanol and diethylamine respectively. The ignition properties of these types of biodiesel were evaluated calculating the cetane index of the transesterification products, and the blending cetane number of the amide biodiesel blended with conventional diesel. Amide biodiesel enhances the ignition properties of the petrochemical diesel fuel, and it could account for the 5% market share that should be secured to biofuels by 2005.     

Production of biodiesel from high free fatty acid Karanja (Pongamia pinnata) oil

Non-edible oil contains several unsaponifiable and toxic components, which make them unsuitable for human consumption. Karanja (Pongamia pinnata) is an underutilized plant which is grown in many parts of India. Sometimes the oil is contaminated with high free fatty acids (FFAs) depending upon the moisture content in the seed during collection as well as oil expression. The present study deals with production of biodiesel from high FFA Karanja oil because the conventional alkali-catalyzed route is not the feasible route. This paper discusses the mechanism of a dual process adopted for the production of biodiesel from Karanja oil containing FFA up to 20%. The first step is acid-catalyzed esterification by using 0.5% H₂SO₄, alcohol 6:1 molar ratio with respect to the high FFA Karanja oil to produce methyl ester by lowering the acid value, and the next step is alkali-catalyzed transesterification. The yield of biodiesel from high FFA Karanja oil by dual step process has been observed to be 96.6–97%.     

Optimization of conversion of waste rapeseed oil with high FFA to biodiesel using response surface methodology

In the present study, waste rapeseed oil with high free fatty acids (FFA) was used as feedstock for producing biodiesel. In the pretreatment step, FFA was reduced by distillation refining method. Then, biodiesel was produced by alkaline-catalyzed transesterification process, which was designed according to the 2⁴ full-factorial central composite design. The response surface methodology (RSM) was used to optimize the conditions for the maximum conversion to biodiesel and understand the significance and interaction of the factors affecting the biodiesel production. The results showed that catalyst concentration and reaction time were the limiting conditions and little variation in their value would alter the conversion. At the same time, there was a significant mutual interaction between catalyst concentration and reaction time.The biodiesel produced in the present experiment was analyzed by gas chromatography/mass spectrometry (GC/MS), which showed that it mainly contained six fatty acid methyl esters. In addition, the diesel indexes analysis showed that most of the fuel properties were in reasonable agreement with the 0# diesel standard of China (GB252-2000) and the biodiesel standard of America (ASTM D6751).     

A review on solid oxide derived from waste shells as catalyst for biodiesel production

The waste eggs and mollusk shells are found to be the richest sources of calcium carbonate and have been utilized for various purposes after proper treatments. When calcined at a proper temperature calcium carbonate converts into CaO, which is a metal oxide. Researchers have found that the CaO prepared from the waste shells can be used as catalyst in biodiesel production process. Utilization of waste shells as a source of CaO not only gives an opportunity to use it as catalyst but also adds value to the waste generated. In this paper a brief discussion with recent development on biodiesel production using waste shell derived solid oxide as catalyst is presented.     

Comparison of biodiesel production from crude Jatropha oil and Krating oil by supercritical methanol transesterification

This work compared the production of biodiesel from two different non-edible oils with relatively high acid values (Jatropha oil and Krating oil). Using non-catalytic supercritical methanol transesterification, high methyl ester yield (85–90%) can be obtained in a very short time (5–10 min). However, the dependence of fatty acid methyl ester yield on reaction conditions (i.e., temperature and pressure) and the optimum conditions were different by the source of oils and were correlated to the amount of free fatty acids (FFAs) and unsaturated fatty acid content in oils. Krating oil, which has higher FFAs and unsaturated fatty acid content, gave higher fatty acid methyl ester yield of 90.4% at 260 °C, 16 MPa, and 10 min whereas biodiesel from Jatropha oil gave fatty acid methyl ester yield of 84.6% at 320 °C, 15 MPa and 5 min using the same molar ratio of methanol to oil 40:1. The product quality from crude Krating oil met the biodiesel standard. Pre-processing steps such as degumming or oil purification are not necessary.     

Improved transesterification of waste cooking oil into biodiesel using calcined goat bone as a catalyst

In this study, potassium hydroxide-treated animal bones were employed? as a solid heterogeneous catalyst in transesterification of waste cooking oil. This catalyst was characterized by the Fourier-transform infrared spectroscopy (FTIR), and it displayed high-catalytic activity for biodiesel production. Optimum conditions for biodiesel production were catalyst loading 6.0% (w/w) of oil, methanol/oil molar ratio 9:1, calcination temperature 800°C, reaction temperature 65°C, and reaction time of 5 h, which gave maximum biodiesel yield of 84%. Reusability of the catalyst was also confirmed by repeated use of the same catalyst three times without losing much of its activity. Hence, calcined goat bones were found to be a potentially applicable catalyst for biodiesel production at industrial scale.     

A bone-based catalyst for biodiesel production from waste cooking oil

Biodiesel production via transesterification of waste cooking oil (WCO) with methanol using waste chicken bone-derived catalyst was investigated. The calcium carbonate content in the waste chicken bone was converted to calcium oxide (CaO) at a calcinations temperature of 800°C. The catalysts were prepared by calcination at 300–800°C for 5 h and catalyst characterization was carried out by X-ray diffraction (XRD) and Brunauer–Emmett–Teller (BET) surface area measurement. CaO was used as catalyst for biodiesel production. The results of the optimization imply that the catalyst concentration of 3.0 wt%, methanol to oil ratio of 3:1, and reaction temperature of 80°C for 3 h provide the maximum values of yield in methyl ester production. Reusability of the catalyst from calcined waste chicken bone was studied for four times, with a good yield.     

Tetramethylguanidine as an efficient catalyst for transesterification of waste frying oils

New catalysts and environmentally benign processes may lead to methyl ester production with improved properties at competitive costs. In this study, transesterification of waste frying oil to biodiesel using tetramethylguanidine as a strong base catalyst was conducted. The influence of catalyst concentration and of certain physicochemical properties of waste frying oil was investigated. Experiments were also performed on a semi-refined cottonseed oil for comparison purposes. Experimental results showed that methyl ester conversion was dependent on the type of oil, catalyst concentration and reaction time.