h-BN加入量对低水泥刚玉质浇注料性能的影响

为了提高低水泥刚玉质浇注料中温处理后的强度和抗热震性,在其配料中引入不同量的h-BN粉(其质量分数分别为0、0.5%、1%、1.5%和2%),经成型、养护、脱模、烘干、750℃热处理后,检测试样的体积密度、显气孔率、常温抗折强度、常温耐压强度、抗热震性,并进行XRD分析。结果表明:随着h-BN加入量的增加,750℃处理后试样的显气孔率有所减小,体积密度逐渐减小,常温耐压强度逐渐增大,常温抗折强度也呈增大趋势,抗热震性逐渐改善。可见,加入h-BN有助于提高低水泥刚玉质浇注料中温处理后强度和抗热震性。     

骨料浸渍硅溶胶对矾土基耐火材料性能的影响

为了改善矾土基耐火材料的力学性能和抗热震性能,分别以SiO2含量(w)为15%和30%的硅溶胶对3~1 mm的矾土熟料粗颗粒进行浸渍处理,再与≤1 mm的矾土熟料颗粒、≤0.074 mm的矾土熟料细粉、α-Al2O3微粉、≤0.074 mm的红柱石细粉、≤0.074 mm的广西白泥、纸浆废液等经配料、成型、干燥、烧成(1400、1450和1500℃保温3 h),制得矾土基耐火材料,同时制备了使用未浸渍3~1 mm矾土熟料的空白试样。结果表明:1)随着烧成温度的升高,试样的常温抗折强度和常温耐压强度呈先升高后降低的变化趋势,其最佳烧成温度为1450℃。2)随着浸渍用硅溶胶浓度的提高,试样的烧后线变化增大,体积密度、常温抗折强度和常温耐压强度降低,高温抗折强度、荷重软化温度和抗热震性能提高,这是由骨料表面硅溶胶层中的SiO2与骨料及周围基质中的Al2O3反应生成了莫来石所致。3)当浸渍用硅溶胶中SiO2含量(w)为15%时,材料的综合性能最优。     

Mechanical Properties of Mullite–Corundum Composites Prepared from Bauxite

Mullite–corundum composites have been prepared by reaction sintering of Indian bauxite having considerable amount of impurities and silica sol. The effect of changing mullite phase proportion on the mechanical properties (i.e., flexural strength, elastic modulus, hot modulus of rupture, thermal shock resistance) of prepared composites has been studied. Flexural strength and elastic modulus increase with increasing free corundum phase content in the composites. Hot modulus of rupture for the sample containing only mullite phase increases with increasing test temperature over entire temperature range. Theoretical thermal shock resistance parameters R and R? are well supported by experimental thermal shock data.     

Development of Andalusite Bricks for Hot Blast Stove

Low-creep andalusite bricks are characterized by high refractoriness under load, good anti-creep property, high mechanical strength, low porosity, good thermal shock resistance, etc. In this study, low-creep andalusite brick specimens were investigated in the lab using mullite, bauxite and andalusite. Andalusite with the different panicle sizes were used in the experiment and the specimen with the best property was selected as the production standard. In addition, the industrial produced low-creep andalusite bricks were compared with other low-creep bricks. The results show that the developed low-creep andalusite bricks is an excellent material for hot blast stove.     

刚玉-莫来石推板的研制与应用

研究了颗粒组成、结合剂种类及含量对刚玉 -莫来石质推板热震稳定性的影响。结果表明 :当颗粒料中莫来石与刚玉的质量比为 3∶1时 ,试样的抗折强度保持率最高 ,与颗粒料全部采用莫来石颗粒或刚玉颗粒相比 ,110 0℃ 水冷 3次后的抗折强度保持率分别提高了 2 5 %和 35 %。另外 ,用硅铝凝胶替代粘土作结合剂 ,也可提高刚玉 -莫来石质推板的热震后抗折强度保持率。研制出的刚玉 -莫来石推板的高温强度高 ,110 0℃ 水冷循环的热震次数超过 4 5次。经国内某厂家试用 ,其寿命可达 12 0次。     

Effect of microsilica addition on the properties of colloidal silica bonded bauxite-andalusite based castables

Colloidal silica bonded bauxite-andalusite based castables were prepared using homogenized bauxite and andalusite as aggregates, andalusite fines, corundum fines, ultrafine Al₂O₃ as matrixes and colloidal silica as binders. Effects of microsilica addition on the green strength, physical properties, hot strength and thermal shock resistance of castables were investigated. Moreover, phase composition and morphological evolution of specimens were characterized by XRD and SEM analysis. Green strength after demoulding, cold strength and hot strength as well as thermal shock resistance of the castables are enhanced with microsilica addition, which attribute to generating more chemical bond (–Si–O–Si–) after demoulding and heating at intermediate temperature (up to 1100 °C), and creating a stronger mullite bonding at higher temperature (1400 °C) compare to the specimens without microsilica.     

Effects of Tabular Corundum Types on Properties of Corundum-spinel Castables

The corundum-spinel castables were prepared by six kinds of tabular corundum as aggregates,respectively,and their linear change rate on heating,apparent porosity,bulk density,cold modulus of rupture,cold crushing strength,hot modulus of rupture and thermal shock resistance were compared and studied. The results show that: 1) the six tabular corundum materials have similar main chemical composition but their physical properties vary for the different technical procedures which result in different properties of castables; 2) the optimal properties of corundum-spinel castables correspond to different tabular corundum types,so the corundum type shall be selected according to the application of the castables.     

硅溶胶结合刚玉和刚玉-莫来石浇注料的性能研究

以电熔白刚玉、电熔莫来石、氧化铝微粉、二氧化硅微粉和硅溶胶为主要原料,制备了硅溶胶、二氧化硅微粉结合刚玉浇注料以及硅溶胶结合刚玉-莫来石浇注料,研究了不同温度处理后浇注料的常温性能、冷态和热态抗折强度以及弹性模量等性能,并进行了差热、X射线衍射和显微结构分析。研究结果表明:1)与二氧化硅微粉相比,硅溶胶能够显著提高浇注料800℃以下的抗折强度;硅溶胶结合和二氧化硅微粉结合的机制以及随温度变化的规律基本一致。2)高温下刚玉骨料中β-Al2O3分解产生的Na2O大部分进入液相,使液相中Na2O含量增加,不利于浇注料中原位生成莫来石,并降低材料的高温强度。3)莫来石加入到硅溶胶结合刚玉浇注料中,能显著降低浇注料的弹性模量,借助于高温下液相的传质作用,莫来石彼此连接形成网络,从而增加了浇注料的强度。     

不同粒度红柱石对矾土基喷涂料性能的影响

以矾土为主要原料,铝酸钙水泥、硅微粉为结合系统,分别研究了不同粒度的红柱石对矾土基喷涂料性能的影响。试样自然干燥24h脱模,再经110℃烘干24h,分别于1000℃、1300℃和1500℃热处理3h。检测各温度热处理后试样的线变化率、体积密度、常温抗折强度、常温耐压强度以及试样的热膨胀系数、耐磨性能和抗热震性能。结果表明,添加粗粒度的红柱石并不能有效弥补矾土基喷涂料经高温热处理产生的收缩。矾土基喷涂料的体积密度随着红柱石粒度的增大而增大。不同粒度的红柱石未对矾土基喷涂料的中温强度产生明显影响,粗粒度的红柱石可以提高矾土基喷涂料的高温强度。矾土基喷涂料的耐磨性能随着红柱石粒度的增大而提高。细粒度的红柱石有利于改善矾土基喷涂料的抗热震性能。     

不同碳含量对镁碳砖性能的影响

研究了碳含量的变化对镁碳砖抗渣侵蚀性、抗氧化性能、高温抗折强度和热震稳定性的影响。研究结果表明：随碳含量增加,镁碳砖的体积密度、耐压强度降低;碳含量在6%~8%时,镁碳砖的高温抗折强度、热震稳定性、抗渣侵蚀性及抗氧化性能好;碳含量低,镁碳砖的抗渣侵蚀性降低;碳含量为14%时,镁碳砖的抗氧化性能最差。     

红柱石及其引入方式对铝硅质浇注料性能的影响

为充分发挥红柱石在铝硅质浇注料中的优异性能,分别以特级矾土、棕刚玉为主要原料配以红柱石制备铝硅质浇注料.检测试样在不同温度下的抗折强度及体积密度、显气孔率及线膨胀率,并对烧后试样的物相组成及显微结构进行表征,以研究红柱石及其引入方式对不同配置的铝硅质浇注料性能的影响.研究结果表明:红柱石以细粉形式引入的铝硅质浇注料,在高温下莫来石反应及二次莫来石化较为充分,试样体积密度、高温抗折强度相对较高,线膨胀率相对较低;相比棕刚玉配置的浇注料,红柱石对矾土配置浇注料性能的改善更为明显,红柱石分解及二次莫来石化相对较为容易,产生的莫来石将矾土熟料紧密连接,有效改善试样的物理性能.     

金属铝结合镁-尖晶石-碳滑板的研制

研究了不同添加物(电熔刚玉、镁铝尖晶石、碳化硅和阿隆)对镁碳材料物理性能和抗热震性的影响,炭素种类对镁碳材料物理性能和抗氧化性的影响以及抗氧化剂种类和加入方式对镁碳材料常温抗折强度和抗氧化性的影响,根据确定的最佳添加物研制连铸钢包用滑板材料。结果表明:加入镁铝尖晶石有利于提高材料的抗热震性;与炭黑相比,添加597微细石墨可显著提高材料的常温抗折强度、致密度以及抗氧化性;以碳化硼和硅粉作为复合添加剂,有利于提高材料中、高温处理后的常温抗折强度,同时也提高了材料的抗氧化性;研制的镁-尖晶石-碳滑板材料在实际使用中的抗拉毛性优于重烧铝锆碳滑板,达到了钢厂的使用要求。     

Preparation and thermal shock resistance of corundum-mullite composite ceramics from andalusite

Corundum-mullite composite ceramics have high hardness, small plastic deformation and other excellent performances at high temperature. Corundum-mullite composite ceramics were fabricated from andalusite and α-Al₂O₃ by in-situ synthesis technology. Effects of mullite/corundum ratio and sintering temperatures on the water absorption, apparent porosity, bulk density, bending strength, thermal shock resistance, phase composition and microstructure of the sample were investigated. Results indicated that the in-situ synthesized mullite from andalusite combined with corundum satisfactorily, which significantly improved the thermal shock resistance as no crack formed after 30 cycles of thermal shock (1100 °C-room temperature, air cooling). Formula A4 (andalusite: 37.31 wt%, α-Al₂O₃: 62.69 wt%, TiO₂ in addition: 1 wt%, mullite: corundum=6:4 in wt%) achieved the optimum properties when sintering at 1650 °C, which were listed as follows: water absorption of 0.15%, apparent porosity of 0.42%, and bulk density of 3.21 g⋅cm⁻³, bending strength of 117.32 MPa. The phase composition of the sintered samples before and after thermal shock tests were mullite and corundum constantly. The fracture modes of the crystals were transgranular and intergranular fractures, which could endow the samples with high thermal shock resistance.     

Properties of New Mullite-SiC Bricks for CDQ Shafts

Currently the service life of CDQ shafts in China is mainly restricted by the properties of the inclined flue bricks.In this work,based on the systematic analysis of the damage mechanism of inclined flue refractories,high performance mullite-SiC bricks were developed.The bricks were produced by corundum,andalusite,SiC and other high purity raw materials.Metal silicon and alumina ultra micropowder were added to form dispersion multi-phase structure,fortifying the matrix and improving the microstructure.The products have excellent properties such as low porosity,high density,good wear resistance,high refractoriness under load,and good thermal shock resistance.The products can replace the ordinary mullite-SiC bricks and obtain a good service life.     

Al2O3-SiC-C质湿式喷射浇注料的研究和应用

以高纯莫来石、碳化硅、SiO2微粉、Al2O3微粉、纯铝酸钙水泥、白刚玉细粉和球沥青等为原料,研究了q值为0.23、0.25、0.27、0.29和0.31时湿式喷射浇注料的流变性能;进一步研究了q值为0.27时,SiC加入量(质量分数分别为12%、15%、18%、21%)对其流变性能、常温物理性能和高温抗折强度、抗热震性能、抗渣侵蚀性能的影响。结果表明:根据Andreassen方程,当q=0.27时,配制的浇注料具有较好的流变性能;加水量为6.5%(w)时,研制浇注料的流变性能类似于宾汉姆流体,适于管道输送;SiC加入质量分数为18%时,浇注料具有较高的高温抗折强度、抗渣侵蚀性能和抗热震性能;经对鱼雷罐和出铁沟的喷补使用证明,研制的湿式喷射浇注料施工性能好,使用性能优异。     

添加浮选镁砂颗粒和Al2O3细粉对方镁石-尖晶石砖性能的影响

以烧结镁砂、浮选镁砂、电熔镁铝尖晶石和煅烧Al₂O₃细粉为主要原料,以木质素磺酸钙为结合剂,经混练、成型、1 650℃烧成制备了方镁石-尖晶石砖,主要研究了以浮选镁砂颗粒替代普通烧结镁砂颗粒以及在此基础上外加不同量煅烧Al₂O₃细粉（质量分数分别为0、3%和5%）对方镁石-尖晶石砖性能的影响。结果表明：1)以浮选镁砂颗粒替代普通烧结镁砂颗粒制备的方镁石-尖晶石砖,显气孔率和常温耐压强度降低,体积密度、抗热震性、高温强度和高温韧性提高。2)在以浮选镁砂颗粒替代普通烧结镁砂颗粒制备的方镁石-尖晶石砖中,随着煅烧Al₂O₃细粉引入量的增多,显气孔率和常温耐压强度降低,体积密度、抗热震性、高温强度和高温韧性提高。     

矾土基电熔尖晶石对矾土基浇注料性能的影响

为了开发矾土基电熔尖晶石的应用,在矾土骨料、纯铝酸钙水泥、Al2O3微粉、SiO2微粉等原料加入量不变(分别为65%、4%、4%和1%)的条件下,变化矾土基电熔尖晶石的加入量(分别为0、6%、8%、10%和12%)和电熔白刚玉细粉的加入量,研究了矾土基电熔尖晶石对矾土基浇注料常温物理性能、热态抗折强度、抗热震性以及抗渣性的影响。结果表明,与不加矾土基电熔尖晶石的浇注料相比,尖晶石加入量为6%~12%时,浇注料的常温性能相差不大,但热态抗折强度及抗热震性均有所提高,抗渣性有很大改善。     

堇青石加入方式对堇青石-莫来石窑具材料性能的影响

为满足锂离子电池正极材料烧成的需要,以堇青石、莫来石、高岭土和氧化铝为原料制备堇青石-莫来石窑具材料,研究了堇青石颗粒和细粉加入量对堇青石-莫来石窑具材料的常温性能、高温抗折强度和抗热震性的影响.并用XRD和SEM分析了试样烧后的物相变化与显微结构.结果表明:随着堇青石颗粒或细粉加入量从0到30％(质量分数),试样的线变化率、显气孔率、高温抗折强度增大,体积密度下降;而对常温抗折强度的影响不大,试样的耐压强度分别呈现下降或提高的趋势,试样的抗热震性先增加后降低,当堇青石颗粒含量为20％,细粉含量为20％时,试样的抗热震性最好.     

新型结合剂SioxX-Zero对喷煤管用无水泥浇注料显微结构和性能的影响

喷煤管是水泥回转窑的关键承力部位,长期承受高温熟料粉尘和气流的剧烈冲刷,需具备优异的高温力学性能。本工作分别以新型SioxX-Zero和传统铝酸钙水泥为结合剂,采用板状刚玉、α-Al₂O₃微粉和碳化硅等为主要原料,分别在1 100 ℃和1 400 ℃热处理3 h,制备了喷煤管用无水泥和低水泥结合Al₂O₃-SiC质浇注料,并研究了新型SioxX-Zero结合剂对浇注料显微结构、常规物理性能和高温力学性能的影响。结果表明:与传统铝酸钙水泥相比,SioxX-Zero能有效提高浇注料流动值和延缓流动值衰减,改善其施工性能。同时,含SioxX-Zero的Al₂O₃-SiC质浇注料中原位生成了数量较多、尺寸较大的针状莫来石,大幅改善了材料的常温抗折/耐压强度、高温抗折强度和高温耐磨性能。     

硅溶胶结合刚玉-莫来石快干浇注料的性能与应用

对比测试了常温浇注成型及在模拟热态修补条件下浇注成型的硅溶胶结合刚玉-莫来石快干浇注料分别在815、1 100和1 400℃保温3 h热处理后的常温抗折强度、常温耐压强度、体积密度和加热永久线变化以及常温浇注成型的硅溶胶结合刚玉-莫来石浇注料和矾土水泥结合刚玉质浇注料的抗热震性,并在钢厂对硅溶胶结合刚玉-莫来石浇注料进行了现场应用试验。结果表明:硅溶胶结合刚玉-莫来石浇注料的烘干强度与普通低水泥刚玉质浇注料的相当,815和1 100℃热处理后强度比烘干强度高;硅溶胶结合刚玉-莫来石浇注料热震循坏(1 100℃,水冷)100次后基本上没有出现裂纹,其耐压强度损失率仅为18.7%;在模拟热态条件下成型的硅溶胶结合刚玉-莫来石浇注料的性能与常温浇注成型的相当。在现场应用试验中,硅溶胶结合刚玉-莫来石浇注料的脱模时间和烘炉时间大大缩短,并且可以热态浇注,具有良好的使用性能。