Latexes of starch-based graft polymers containing polymerized acrylonitrile

The scope of graft reactions to produce starch-based latexes was extended by graft polymerization of acrylonitrile (AN) onto gelatinized cationic starch possessing quaternary amine functionality and by graft terpolymerization of AN and t-butylaminoethyl methacrylate (TBAEM) onto gelatinized starch by cerium (IV) initiation at 25°C. Grafting onto starches containing highly basic quaternary amines gave polyacrylonitrile [poly(AN)] grafts having about one fourth the number-average molecular weight (M?_n) (178,000–232,000) of those produced by grafting AN onto starches containing the less basic tertiary amine groups. Sonification at 20 KHz of graft polymerization reaction mixtures having up to 8% solids reduced viscosities from 400–3000 cP to 10–40 cP. Diameters of dried particles measured about 300–1500 Å. Shaker-type agitation during grafting onto starch having quaternary amine groups produced poly(AN) chains with lower M?_n values than those produced during blade stirrer-type agitation. M?_n values of grafted poly(AN) decreased with increasing reaction time, degree of substitution of amine in the starch, gelation time of cationic starch at 95°C, and cerium (IV) concentration. AN was copolymerized with TBAEM at molar ratios of 14–85:1 in grafting onto gelatinized starch to yield copolymer side-chain grafts analyzing 8–52:1 of polymerized AN to TBAEM moieties.     

Swelling and rheology of saponified starch–g–polyacrylonitrile copolymers. Effect of starch granule pretreatment and grafted chain length

A series of well-characterized starch–g–polyacrylonitrile (PAN) graft copolymers was prepared from corn starch which had been heated in water at temperatures up to 94°C to vary the extent of starch granule swelling and disruption. Graft polymerization onto gelatinized starch gave less frequent grafting of higher molecular weight PAN than comparable graft polymerizations onto ungelatinized starch. A graft copolymer was also prepared from gelatinized starch under high dilution conditions to give lower molecular weight grafted PAN and more frequent grafting. Graft copolymers were then saponified with sodium hydroxide to convert nitrile substituents to a mixture of carboxamide and sodium carboxylate. Saponified graft copolymers were only partially water soluble and consisted largely of highly swollen, insoluble gel, which was separated from solubles for the study of physical properties. Saponification mixtures were also dried to yield highly absorbent polymer films. With the exception of the graft copolymer prepared under high dilution conditions, the physical properties of saponified graft copolymers depended on whether or not the granules of starch were gelatinized before graft polymerization. Compared with saponified graft copolymers derived from ungelatinized starch, those prepared from gelatinized starch gave films that absorbed larger amounts of aqueous fluids. Also, the gel fractions from these saponified gelatinized polymers exhibited higher water swelling, lower shear modulus, and a lower reduced viscosity function (η/cQ). The saponified graft copolymer prepared from gelatinized starch under high dilution conditions more closely resembled those prepared from ungelatinized starch, suggesting that molecular weight of grafted PAN and the grafting frequency rather than starch granule pretreatment might be the most important factor which influences properties.     

Graft copolymers of starch–polyacrylonitrile prepared by ferrous ion–hydrogen peroxide initiation

The effect of concentration, reactant ratios, temperature, and starch pretreatment on grafting of acrylonitrile onto starch were studied. Grafting was efficient at high concentrations (8–12% starch) when granular starch was used. The molecular weights for grafted polyacrylonitrile (PAN) were higher when gelatinized starch was used, but grafting efficiencies (grafted PAN/total PAN) were much lower. The molecular weight of the grafted side chain increased with increased concentration of reactants. The grafting frequency was highest when the reaction mixture was kept at 5°C and decreased with increased swelling of the starch. The starch–polyacrylonitrile graft copolymers were saponified and dried to give products which absorbed 75–440 ml H₂O per gram and 20–70 ml synthetic urine per gram.     

Graft copolymerization of methyl methacrylate onto starch using a Ce(IV)–glucose initiator system

Graft copolymerization of methyl methacrylate onto starch was carried out in aqueous medium using Ce(IV)–glucose initiator in the temperature range 40–60°C. Effects of concentration of Ce(IV), glucose, H₂SO₄, monomer, and starch on grafting were investigated. Percentages of grafting were evaluated and compared. The overall energy of activation was calculated from the effects of time and temperature of polymerization. The reaction mechanism was also discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 981–990, 2004     

Synthesis and properties of poly(acrylonitrile‐co‐p‐trimethylsilylstyrene) and poly(acrylonitrile‐co‐p‐trimethylsilylstyrene‐co‐styrene)

Copolymerization of acrylonitrile (AN) with p‐trimethylsilylstyrene (TMSS) was carried out at 60°C in bulk and in solution in the presence of 2,2′‐azobisisobutyronitrile (AIBN). The reactivity ratios of AN (M₁) and TMSS (M₂) were determined to be r₁ = 0.068 and r₂ = 0.309. The effects of the AIBN concentration and that of the chain transfer agent CCl₄ on the molecular weights (MWs) of the copolymers were investigated. An increase in the concentrations of AIBN or CCl₄ in solution led to a decrease in MW. Poly(AN‐co‐TMSS‐co‐St) was synthesized in solution using AIBN as the initiator. The molar fraction of AN was 0.415, while the molar ratio of TMSS/St varied from 1 : 1 to 1 : 9. The transition temperatures and thermal and thermooxidative stabilities of poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) were investigated. The differential scanning calorimeter technique was used to determine the compatibility of the poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) with commercial poly(AN‐co‐St). All the blends show a single glass transition temperature, which indicates the compatibility of the blend components. The surface film morphology of the blends mentioned above was examined by X‐ray photoelectron spectroscopy. The data obtained indicate that the silicon‐containing copolymer is concentrated in the surface layer. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1920–1928, 2000     

Starch‐g‐polycaprolactone copolymerization using diisocyanate intermediates and thermal characteristics of the copolymers

Starch‐g‐polycaprolactone copolymers were prepared by two‐step reactions. The diisocyanate‐terminated polycaprolactone (NCO–PCL) was prepared by introducing NCO on both hydroxyl ends of PCL using diisocyanates (DI) at a molar ratio between PCL and DI of 2:3. Then, the NCO–PCL was grafted onto corn starch at a weight ratio between starch and NCO–PCL of 2:1. The chemical structure of NCO–PCL and the starch‐g‐PCL copolymers were confirmed by using FTIR and ¹³C‐NMR spectrometers, and then the thermal characteristics of the copolymers were investigated by DSC and TGA. By introducing NCO to PCL (M_n : 1250), the melting temperature (T_m ) was reduced from 58 to 45°C. In addition, by grafting the NCO–PCL (35–38%) prepared with 2,4‐tolylene diisocyanate (TDI) or 4,4‐diphenylmethane diisocyanate (MDI) onto starch, the glass transition temperatures (T_g 's) of the copolymers were both 238°C. With hexamethylene diisocyanate (HDI), however, T_g was found to be 195°C. The initial thermal degradation temperature of the starch‐g‐PCL copolymers were higher than that of unreacted starch (320 versus 290°C) when MDI was used, whereas the copolymers prepared with TDI or HDI underwent little change. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 986–993, 2000     

Graft copolymerization onto starch. III. Grafting of acrylonitrile to gelatinized potato starch by manganic pyrophosphate initiation

Recent development of synthesis and applications in grafting of acrylonitrile (AN) to gelatinized starch by Ce⁴⁺ initiation have been briefly reviewed. Using the Mn³⁺ method, the effects of starch pretreatment temperature on grafting parameters in grafting of AN onto starch have been studied. Total conversion of AN to PAN and % add-on were almost constant and showed only slight variation with increasing starch pretreatment temperature. Average molecular weight of grafts showed, however, an increase by a factor of nearly 10 (i.e., from 0.4 X 10⁵ to 4 X 10⁵) after swelling and gelatinization of the starch, and the grafting frequency (anhydroglucose units per grafted chain) increased in proportion. In grafting of AN onto gelatinized starch, increasing Mn³⁺ concentration increased the conversion of monomer and % add-on, whereas the average molecular weight of grafts and the grafting frequency (AGU/chain) decreased. An increase in the amount of starch also increased the conversion of monomer and the grafting frequency (AGU/chain) but decreased the % add-on and the average molecular weight of the grafts. Selective solution of PAN homopolymer by dimethylformamide indicated that grafting efficiencies were high in all cases. The results are interpreted in terms of slow termination rates due to high viscosity of gelatinized starch.     

Grafting of a styrene–acrylonitrile binary monomer mixture onto cellulose extracted from pine needles

In an attempt to develop new reactive membrane materials, we graft‐copolymerized styrene (Sty) and acrylonitrile (AN) onto cellulose extracted from pine needles by a chemical initiation method. The optimum grafting reaction conditions for Sty onto cellulose were earlier evaluated as [Sty] = 656.25 mmol/L and [potassium persulfate–ferrous ammonium sulfate] = 146.3:12.75mmol/L in 20 mL of H₂O with a reaction time of 3 h and a reaction temperature of 60°C for 1 g of cellulose. Under these conditions, Sty was graft‐copolymerized with AN at five different concentrations of the latter. Grafting parameters and different rates of concentration were evaluated. The effects of additives such as ZnCl₂, LiNO₃, and Cu(NO)₃ were studied at the best comonomer concentration of Sty–AN. In the presence of ZnCl₂, Sty–AN graft‐copolymerized in an alternate way, thus, making it evident that ZnCl₂ coordinated to form a “complexomer,” or complex of monomers [Sty^?AN⁺…ZnCl₂], of two monomers. Evidence of the structural characteristics of grafted chains were provided by characterization with elemental analysis, thermal analysis, and Fourier transform infrared spectroscopy. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2000–2007, 2002     

Synthesis and characterization of biodegradable polyethylene by graft copolymerization of starch using glucose–Ce(IV) redox system

Graft copolymerization of low‐density polyethylene (LDPE) onto starch was carried out with glucose–cerium(IV) redox initiator in an aqueous sulfuric acid medium under nitrogen atmosphere. The graft yield was influenced by various parameters like reaction time, temperature, and concentrations of acid, glucose, polyethylene (PE), starch, and initiator. A maximum graft yield of 85.66% was obtained at a temperature of 50°C and at higher concentration of starch. Effect of grafting on crystallinity, morphology, and thermal properties of modified PE has been evaluated using X‐ray diffraction, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA/DTA). Biodegradability of starch‐grafted PE has been tested applying soil‐burial test. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3229–3239, 2006     

Graft copolymers of starch with mixtures of acrylamide and the nitric acid salt of dimethylaminoethyl methacrylate

Mixtures of acrylamide and the nitric acid salt of dimethylaminoethyl methacrylate (DMAEMA·HNO₃) have been graft polymerized onto unmodified wheat starch with ferrous ammonium sulfate–hydrogen peroxide initiation. Graft polymerizations were carried out with both unswollen starch granules and granules that had been swollen by heating in water to 60°C. Ungrafted synthetic polymers were removed from graft copolymers by cold-water extraction and were characterized by their M?_n and DMAEMA·HNO₃ content. Graft copolymers were characterized with respect to per cent add-on, M?_n and DMAEMA·HNO₃ content of grafted polymer, and grafting frequency. Ungrafted synthetic polymers contained a mole percentage of DMAEMA·HNO₃ equal to or greater than that present in the initial monomer mixtures; whereas in most grafted polymers the mole-% DMAEMA·HNO₃ in the grafted branches was less than that in the starting monomers. At all monomer ratios examined, polymer grafted to swollen starch granules contained a higher percentage of DMAEMA·HNO₃ then polymer grafted to unswollen starch. The influence of starch granule swelling on the molecular weight and frequency of grafted branches was correlated with the composition of the initial monomer mixture. It was determined that the effect of granule swelling on graft copolymer structure would be minimal when 25–30 mole-% DMAEMA·HNO₃ was used. In an acetonitrile–water solvent system, reactions with 20 and 50 mole-% DMAEMA·HNO₃ produced graft copolymers with less DMAEMA·HNO₃ in grafted branches than corresponding graft polymerizations run in water. The flocculation of 3% aqueous suspensions of diatomaceous silica was examined with selected starch graft copolymers.     

Graft copolymerization of acrylamide–methylacrylate comonomers onto cellulose using ceric ammonium nitrate

The graft copolymerization of acrylamide–methylacrylate comonomers was carried out using ceric ammonium nitrate as initiator in the presence of nitric acid at 25 ± 1°C. The effects of feed molarity, feed composition, reaction time, and temperature on graft yield (%G) and other grafting parameters were investigated. The determination of rate of ceric (IV) ions disappearance as a function of feed molarity and reaction time was useful in the determination of the rate of ceric (IV) ions consumption during graft copolymerization. The graft yield (%G) in the presence of acrylamide increases because of the synergistic effect of acrylamide comonomer. The composition of the grafted chains (F_AAm) varies on varying the feed composition and reaction temperature but is almost constant during feed molarity variation. The Mayo and Lewis method was used to determine the reactivity ratios of acrylamide (r₁) and methylacrylate (r₂), which are 0.65 and 1.07, respectively. The product of reactivity ratio (r₁ r₂) is less then unity; hence, an alternate arrangement of comonomer blocks in the grafted copolymer chain is proposed. The rate of graft copolymerization of comonomers onto cellulose is second power to the concentration of comonomers and square root to the concentration of ceric ammonium nitrate. Suitable reaction steps for graft copolymerization of comonomers onto cellulose are proposed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2631–2642, 2002     

Influence of starch granule swelling on graft copolymer composition. A comparison of monomers

Seven monomers, which varied widely in water solubility and ionic charge, were graft polymerized onto both unswollen starch and starch that had been swollen by heating in water to 60°C. Polymerizations were initiated with ferrous ammonium sulfate hexahydrate–hydrogen peroxide and, where applicable, with ceric ammonium nitrate. Graft copolymers were freed of ungrafted homopolymer by solvent extraction and were characterized by weight percentage of synthetic polymer incorporated in the graft copolymer, molecular weight of grafted branches, and grafting frequency. The influence of starch granule swelling on graft copolymer structure varied with the monomer used and could not be predicted on the basis of water solubility of monomer or its resulting polymer. With acrylonitrile and acrylamide, swollen starch gave higher molecular weight and less frequent grafts than unswollen starch. However, methyl methacrylate, N,N-dimethylaminoethyl methacrylate · HNO₃, N-t-butylaminoethyl methacrylate. HNO₃, and 2-hydroxy-3-methacryloyloxypropyltrimethylammonium chloride produced less frequent graft of higher molecular weight when starch was unswollen. With acrylic acid, graft molecular weight was independent of starch granule swelling, although grafting was less frequent when swollen starch was used.     

Synthesis of starch‐graft‐polyacrylonitrile hydrolyzate and its characterization

The graft copolymerization of three vinyl monomer species, acrylonitrile (AN), acrylamide (AAm), and acrylic acid (AA), onto starch was carried out with ceric salt (Ce salt) as an initiator. With 3 mmol/L Ce salt, the monomer activity onto starch decreased in the following order: AN > AAm > AA. Grafting efficiency with AN as the grafting monomer was greater than 90%, but with AA and AAm, it was less than 50%. Starch‐graft‐polyacrylonitrile was hydrolyzed to introduce amide and carboxyl groups into starch. The hydrolyzates were analyzed with infrared spectroscopy. The hydrolysis reaction was accelerated with increasing alkali concentration, reaction temperature, and time. The water absorbancy of the hydrolyzate increased with an increasing carboxyl molar fraction in the polymer, and it dissolved in water above a 0.6 molar fraction. The absorbancy of water was 2 times higher than that of a NaCl aqueous solution. The copper‐ion‐exchange capacity of the sample was greater in graft copolymers with higher carboxyl group contents. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1437–1443, 2001     

Graft polymerization of vinyl acetate onto starch. Saponification to starch–g–poly(vinyl alcohol)

Graft polymerizations of vinyl acetate onto granular corn starch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinylacetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. However, over half of the polymer was present as ungrafted poly-(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficiency. However, grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate-methyl methacrylate was carried out near 0°C, although conversion of monomers to polymer was low and grafted polymer contained 40-50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch–g–poly(vinyl acetate) to starch–g–poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch–g–poly(vinyl alcohol) in hot water was less than 50%; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized starch for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch–g–poly(vinyl acetate) with about 35% add-on, and a grafting efficiency of about 40% was obtained. A film cast from a starch–g–poly(vinyl alcohol) copolymer in which homopolymer was not removed exhibited a higher ultimate tensile strength than a comparable physical mixture of starch and poly(vinyl alcohol).     

Synthesis and characterization of butyl acrylate graft sodium salt of partially carboxymethylated starch

Graft copolymers were synthesized by graft copolymerization of butyl acrylate (BA) onto sodium salt of partially carboxymethylated starch (Na‐PCMS). Ceric ammonium nitrate (CAN), a redox initiator, was used for initiation of graft copolymerization reaction. All the experiments were run with Na‐PCMS having degree of substitution, DS = 0.35. The grafting reaction was characterized by parameters such as % total conversion (%Ct), % grafting (%G), % grafting efficiency (%GE), and % add‐on. Graft copolymers were characterized by infrared spectral analysis and scanning electron microscopy. Variables affecting graft copolymerization reaction such as nitric acid concentration, reaction time, reaction temperature, and ceric ion concentration were investigated. The results revealed that 0.3M CAN as initiator, 0.3M HNO₃, with reaction time 4–4.5 h at 25–30°C were found as suitable parameters for maximum yield of graft copolymerization reaction. © 2006 Wiley Periodicals, Inc. JAppl Polym Sci 102: 3334–3340, 2006     

Reactive extrusion vs. batch preparation of starch–g–polyacrylonitrile

Acrylonitrile (AN) was graft polymerized onto unmodified cornstarch by a continuous reactive extrusion process and, for comparison, by a typical batch reaction process. The effect of AN/starch weight ratios, level of ceric ammonium nitrate (CAN) initiator, starch in water concentration, reaction temperature, reaction time, and extruder screw speed in the reactive extrusion process was studied. Add-on, reaction efficiency, grafting frequency, weight average molecular weight (MW) and MW distribution of polyacrylonitrile (PAN), and water absorbency of the saponified copolymers were determined. Processing times in the twin-screw extruder (ZSK) were 2–3 min, and total reaction time was about 7 min before reaction of the extruded material was terminated, compared to a reaction time of 2 h used in the typical batch procedure. The continuous reactive extrusion process was found to be a rapid and efficient means of preparing St-g-PAN with high add-on (% PAN of the grafted product). For example, 42% add-on was achieved within the 7-min reaction period using an AN/starch weight ratio of 1.0 (3.5% CAN, starch weight basis), as compared to 38–49% for the 2-h batch process (0.75–1.5 AN/starch ratio). Percentages of homopolymer of the copolymers were low for both extrusion and batch processes. Grafting frequencies were substantially higher while MWs were significantly lower for grafts from the extrusion process. Water absorbency of the saponified St–g–PAN products was somewhat greater for the products prepared by the batch process.     

Synthesis and characterization of poly(hydroxamic acid)–poly(amidoxime) chelating ligands from polymer‐grafted acacia cellulose

Graft copolymerization of methyl acrylate (MA) and acrylonitrile (AN) onto acacia cellulose was carried out using free radical initiating process in which ceric ammonium nitrate (CAN) was used as an initiator. The optimum grafting yield was determined by the certain amount of acacia cellulose (AGU), mineral acid (H₂SO₄), CAN, MA, and AN at 0.062, 0.120, 0.016, 0.397, and 0.550 mol L^?1, respectively. The poly(methyl acrylate‐co‐acrylonitrile)‐grafted acacia cellulose was obtained at 55°C after 2‐h stirring, and purified acrylic polymer‐grafted cellulose was characterized by FTIR and TG analysis. Therein, the ester and nitrile functional groups of the grafted copolymers were reacted with hydroxylamine solution for conversion into the hydroxamic acid and amidoxime ligands. The chelating behavior of the prepared ligands toward some metal ions was investigated using batch technique. The metal ions sorption capacities of the ligands were pH dependent, and the sorption capacity toward the metal ions was in the following order: Zn²⁺ > Fe³⁺ > Cr³⁺ > Cu²⁺ > Ni²⁺. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan

Poly(3‐hydroxy octanoate) (PHO), poly(3‐hydroxy butyrate‐co‐3‐hydroxyvalerate) (PHBV), and linoleic acid were grafted onto chitosan via condensation reactions between carboxylic acids and amine groups. Unreacted PHAs and linoleic acid were eliminated via chloroform extraction and for elimination of unreacted chitosan were used 2 wt % of HOAc solution. The pure chitosan graft copolymers were isolated and then characterized by FTIR, ¹³C‐NMR (in solid state), DSC, and TGA. Microbial polyester percentage grafted onto chitosan backbone was varying from 7 to 52 wt % as a function of molecular weight of PHAs, namely as a function of steric effect. Solubility tests were also performed. Graft copolymers were soluble, partially soluble or insoluble in 2 wt % of HOAc depending on the amount of free primary amine groups on chitosan backbone or degree of grafting percent. Thermal analysis of PHO‐g‐Chitosan graft copolymers indicated that the plastizer effect of PHO by means that they showed melting transitions T_ms at 80, 100, and 113°C or a broad T_ms between 60.5–124.5°C and 75–125°C while pure chitosan showed a sharp T_m at 123°C. In comparison of the solubility and thermal properties of graft copolymers, linoleic acid derivatives of chitosan were used. Thus, the grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan decrease the thermal stability of chitosan backbone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:81–89, 2007     

Generation and structure–property behavior of novel liquid crystalline foams produced via a gas supersaturation technique

Linear and star-branched polyoxybenzoate–polyoxyphenoxybenzoate copolymers (POB-co-POPB) at a 65/35 molar ratio were synthesized via melt acidolysis using AB-type monomers and branching agents. By controlling the molecular weight and topology of these polymers, both melt processability and solid-state CO₂ gas absorption behavior were enhanced. POB–POPB copolymers with a molar ratio 65/35 showed a glass transition of 143°C and completion of melting at ca. 300°C. POB–POBP copolymers with a systematically increasing branching agent content showed a systematically decreasing peak intensity in wide-angle X-ray diffraction, indicating that increasing branch-point concentration leads to a decrease in liquid-crystal ordering. Star-branched POB–POPB copolymers showed greatly enhanced carbon dioxide gas absorption behavior relative to their linear counterparts. Whereas CO₂ blown foams of linear POB-co-POPB produced by the gas supersaturation technique had a relatively high density and showed highly anisotropic bubble growth, well-defined, nearly isotropic foams of star-branched POB-co-POPB with a mean cell size from 200 to 400 μ were made using the gas supersaturation technique. Structural features were characterized via scanning electron microscopy, and mechanical properties were determined by indentation testing with a 0.25 in. ball indenter. These LCP foams exhibit relative mechanical properties similar to polystyrene and microcellular polycarbonate foams. A strong inverse relationship was noted between cell size and modulus for liquid crystalline foams with a cell size below 400 μm. © 1994 John Wiley & Sons, Inc.