XANES and EXAFS analysis of copper ion-exchanged ZSM-5 zeolite catalyst used for nitrogen monoxide decomposition

XANES and EXAFS analysis of Cu ion-exchanged ZSM-5 zeolite, a highly active catalyst for NO decomposition, is performed. The copper species in the zeolite are Cu(II) ions in the zeolite cages. The contribution of Cu-Cu local structure is suggested for high loading samples. The Cu atoms in the zeolite are more ionic than CuO. The analysis of the catalyst deactivated by SOx treatment suggests the presence of Cu atoms surrounded by SO₄ ions which blocks the adsorption of NO molecules.     

ZSM-5沸石分子筛吸附模拟含铬废水的研究

本论文以正硅酸乙酯为硅源、偏铝酸钠为铝源、四丙基氢氧化铵为模板剂,利用水热合成法制备ZSM-5沸石分子筛并将其应用到吸附水中六价铬的研究,考察了吸附时间、铬酸钾溶液pH值、吸附剂用量、吸附温度对吸附效果的影响。结果表明,最佳吸附条件是:吸附剂的使用量为0.5g,铬酸钾溶液pH值为5,吸附时间为60 min,吸附温度为30℃,此时,六价铬的去除率最高,达到了93.46%。     

水在ZSM-5型分子筛中吸附的Monte Carlo模拟

构建了ZSM-5型分子筛物理模型,采用Connoly表面方法和Solvent表面方法对ZSM-5型分子筛的几何结构和性质进行了模拟分析。通过巨正则系综蒙特卡罗方法(GCMC)模拟研究了水蒸气在ZSM-5型分子筛上的吸附特性。通过模拟方法看到了实验难以表征的水蒸气在分子筛中具体吸附位,研究了压力、温度和硅铝比对ZSM-5型分子筛吸附性能的影响及其吸附热的变化规律。     

Differences between ZSM-5 and ZSM-11 zeolite catalysts in 1-hexene aromatization and isomerization

ZSM-5 and ZSM-11 zeolites with high crystallinity are synthesized and tested in the aromatization and isomerization reactions of 1-hexene at 370 °C in a continuous flow fixed bed. The results indicate that ZSM-5 and ZSM-11 zeolites possess similar acid site amount and strength, and most of the acid sites belong to Brønsted acid. When the ZSM-5 and ZSM-11 zeolites were used as catalysts, the aromatics selectivity over ZSM-11 catalyst was higher than that over ZSM-5 catalyst in contrast to i-paraffins selectivity, maybe attributed to that the C₇ and C₈ aromatics have an easier exit from the ZSM-11 zeolite. Moreover, the decrease of particle size can present superior aromatics selectivity and less i-paraffins selectivity in the aromatization and isomerization of 1-hexene over the ZSM-11 catalyst.     

ZSM-5沸石分子筛吸附模拟废水中对苯二酚的研究

以正硅酸乙酯为硅源、偏铝酸钠为铝源、四丙基氢氧化铵为模板剂,利用水热合成法制备ZSM-5沸石分子筛并将其应用到吸附水中对苯二酚的研究,考察了吸附时间、对苯二酚溶液pH值、吸附温度、吸附剂用量对吸附效果的影响。结果表明,最佳吸附条件是:吸附温度为35℃,吸附时间为60 min,对苯二酚溶液pH值为6,吸附剂用量为0.4 g。此时,对苯二酚的去除率最高,达到了68.28%。     

Phenylhydrazine rearrangement revisited over modified ZSM-5 catalysts

The rearrangement of phenylhydrazine too- andp-phenylenediamines was carried out over ZSM-5 and its modified catalysts. Sm and V showed the promoting effect. In presence of ammonia flow Ga and Cr modified ZSM-5 catalysts gave good yields ofo- andp-phenylenediamines. The better temperature and WHSV for this reaction are found to be 400°C and 0.25 h^–1 respectively. The SiO₂/Al₂O₃ catalyst showed very low ortho-para selectivity when compared with zeolite catalysts.IICT Communication No. 3372.     

超微ZSM-5分子筛的合成

将原料硫酸铝、硅酸钠以及模板剂按不同配比,在实验室采用常规加热温度和压力合成超微ZSM-5分子筛,采用静态苯吸附、XRD、SEM和IR等表征方法对所得样品进行表征,结果表明,合成的产品从晶体结构符合ZSM-5分子筛的典型结构,颗粒大小达到超微分子范围。     

基于沸石ZSM-5的CH4/N2/CO2二元体系吸附平衡

采用Rubotherm磁悬浮天平测量CH₄、N₂和CO₂在沸石ZSM-5上的单组分吸附平衡等温线,温度273～353 K,压力0～500 kPa。采用Sips模型、Toth模型和MSL模型对单组分吸附平衡实验数据进行拟合,拟合结果良好,非线性回归得到相应的模型参数。测量双组分CO₂/N₂、CO₂/CH₄和CH₄/N₂在沸石ZSM-5上的竞争吸附平衡等温线,实验温度为293 K,实验压力为0～500 kPa。采用基于Sips模型的理想吸附溶液理论和双组分MSL模型预测双组分气体在沸石ZSM-5上的竞争吸附平衡等温线,并与实验结果进行比较,预测结果良好。比较CO₂/N₂、CO₂/CH₄以及CH₄/N₂体系在沸石ZSM-5上的竞争吸附选择性系数,探究沸石ZSM-5吸附分离烟道气（CO₂/N₂体系）、垃圾填埋气（CO₂/CH₄体系）或煤层气（CH₄/N₂体系）的可行性,为将来进行工艺设计提供基础数据。     

ZSM-5沸石对水溶液中铅离子的吸附性能

研究了ZSM-5沸石对水溶液中铅离子（Pb^2＋）的吸附性能,考察了Pb^2＋初始浓度、吸附剂用量、pH值和吸附时间等因素对吸附的影响。结果表明：ESM-5沸石对水溶液中铅离子有较好的去除效果,当其用量为40g／L时,水溶液中铅离子的吸附去除率达到96．09％;吸附过程在180min时达到吸附平衡;溶液pH值和初始浓度对水溶液中铅离子的去除也有显著的影响,中性和碱性条件下的去除率大于酸性时的去除率;平衡吸附量与吸附平衡浓度之间的关系较好符合Freundlich和Langmuir等温吸附方程所描述的规律。     

Phosphorus poisoning of ZSM-5 and Pt/ZSM-5 zeolite catalysts in diesel exhaust gas conditions

Powdered ZSM-5 and Pt/ZSM-5 catalysts were studied as fresh and after two treatments: hydrothermal ageing and phosphorus poisoning in hydrothermal conditions. The results showed that the deactivating effect of phosphorus was stronger than the effect of the hydrothermal treatment alone. Phosphorus had accumulated in the samples during the ageing. The decrease in specific surface area and increase in Pt particle size indicated the possible reasons for deactivation.     

Unique properties of Ir/ZSM-5 catalyst for NO reduction with CO in the presence of excess oxygen

The reduction of NO with CO in the presence of excess oxygen was investigated over different noble metal catalysts for probing the relationship between catalytic properties and adsorption behaviors. Among the four precious metal catalysts investigated, Ir/ZSM-5 was found to be the only active one for NO reduction with CO under lean conditions. With the decreasing of the Ir content, higher NO conversion and CO selectivity was obtained. Temperature-programmed reaction (TPR) studies of NO/H₂/O₂ and NO/CO/O₂ showed that the Pt/ZSM-5 was active when H₂ was used as the reductant, whereas, the Ir/ZSM-5 was active when CO was the reducing agent. This difference is due to the different mechanisms of the two reactions. Temperature-programmed desorption (TPD) of NO, CO and O₂ showed that NO could dissociate more easily over the Ir/ZSM-5 than on the Pt/ZSM-5, while the oxidation of CO by O₂ proceeded more rapidly on the Pt/ZSM-5 than on the Ir/ZSM-5. The presence of excess O₂ inhibited drastically the dissociation of NO, which is considered as the key step for the NO–CO reaction. The high dissociation rate of NO over the Ir/ZSM-5 is visualized as the key factor for its superior high activity in NO reduction with CO under lean conditions.     

不同载体成型的ZSM-5催化剂上甲醇芳构化反应性能

以ZSM-5分子筛为活性组分,采用不同的氧化物载体挤条制备催化剂,并对催化剂的甲醇芳构化反应性能进行评价。采用X射线衍射、氨程序升温脱附和N₂低温吸附-脱附等方法对催化剂进行表征。结果表明,添加氧化物载体后,催化剂的芳构化反应性能明显提高,催化剂芳构化反应性能与其酸性质有着密切联系,Zn/La-ZSM-5(Al₂O₃)催化剂的芳构化反应性能较好,主要归因于催化剂具有适宜的酸分布和孔结构。在反应压力0.1 MPa、空速0.8 h^-1、反应温度437 ℃和反应时间240 min条件下,轻质芳烃收率为42.36%.     

Estimation of crystalline phase in ZSM-5 zeolites by infrared spectroscopy

A fast and accurate method for identification and determination of purity of Zeolite Socony Mobil 5 (ZSM-5) zeolite was developed using the IR optical density ratio of the bands at 550 and 450 cm^?1 in the mid-IR region of the structure spectra. The optical density values obtained from the proposed method, for ZSM-5 zeolite synthesized, are compared with those of the Bayer ZSM-5 zeolite used as reference material. For well-crystallized calcined ZSM-5 zeolite, this ratio is circa 0.8. This ratio is found to be less, if amorphous silicate is present in zeolite. The presence of a band at 550 cmSUP>?1 in addition to the one at 450 cm^?1 shows that ZSM-5 zeolite has been formed even if the material is X-ray amorphous. The absence of the structure-sensitive band at 550 cm^?1 unambiguously indicates that such a zeolite has not been formed.     

Adsorption of alcohols from aqueous solution by ZSM-5

Isotherms have been measured for the adsorption from aqueous solution of water soluble alcohols onto the zeolite ZSM-5. For methanol and ethanol the amount of alcohol adsorbed increases with increasing percentage of Al₂O₃, whereas for n-butanol the amount adsorbed decreases as the amount of Al₂O₃ increases. Adsorption of alcohols is also dependent on the cation form. For the alkali metal ion forms, the amount of alcohol adsorbed decreases as the ionic size increases, the effect being particularly pronounced for Cs⁺. Subsequent alcohol desorption was studied by thermogravimetry and mass spectrometry which showed that the zeolite retained a portion of the alcohol to temperatures (ca 250°C) sufficiently high that catalytic breakdown occurred. This reduces its likely potential for commercial alcohol concentration.     

Co-adsorption of nitrogen monoxide and nitrogen dioxide in zeolitic de-NOx catalysts

Room temperature adsorption and temperature programmed desorption (TPD) of NO, NO with O₂, and NO after NO₂ saturation were investigated for Na/Y, Na/ZSM5, Cu/ZSM5 and SiO₂ gel. The adsorbates were characterized by TPD, using mass spectrometry to identify the desorbed molecules. In the presence of O₂, the adsorption of NO and NO₂ is non-additive; co-desorption of nearly equal amounts of NO and NO₂ takes place suggesting the formation of a complex with an overall composition N₂O₃ within the zeolite. Since SiO₂ gel does not adsorb NO nor NO₂, the adsorption capacity of the zeolites is a function of their specific structure. The oxidation of NO to NO₂ is catalyzed by Na/Y and Na/ZSM5.     

Organic template-free synthesis of ZSM-5/ZSM-11 co-crystalline zeolite

A series of ZSM-5/ZSM-11 co-crystalline zeolites with various compositions and morphologies were successfully synthesized via an organic template-free hydrothermal route and characterized by XRD, XRF, SEM, NMR and N₂ adsorption/desorption technologies. The effects of raw materials and batch composition were investigated systematically. Various silicon sources can be employed in the organic template-free synthesis of ZSM-5/ZSM-11 co-crystalline zeolite, however only a few types of aluminum sources are available. This organic template-free system is favorable to the aluminum-rich zeolite. With the increase of initial SiO₂/Al₂O₃ ratio, the ZSM-5 percentage in the ZSM-5/ZSM-11 co-crystalline zeolite increases as well as the crystal size, and especially the morphology of ZSM-5/ZSM-11 co-crystalline zeolite prepared from the colloidal silica-NaAlO₂ solution system changes gradually from nano-rod aggregation, micro-spindle to single hexagon and then to twinned hexagon crystals. Moreover, Na⁺ and OH⁻ in the initial materials can promote the nucleation of the ZSM-5/ZSM-11 co-crystalline zeolite significantly and are beneficial to the formation of crystals with relatively low length/width ratio, while K⁺ postpones the crystallization process seriously.     

甲醇制芳烃反应中ZSM-5催化剂改性技术

芳烃是种重要的化工原料,在众多领域得到广泛应用。随着甲醇生产技术的成熟,甲醇制芳烃工艺已经成为现阶段非石油路线合成轻质芳烃的重要途径。目前,甲醇制芳烃工艺中常用的催化剂为ZSM-5分子筛,但仍需对分子筛进行合适的后处理改性操作如调变分子筛酸性、活性中心位点和孔道结构等,以提高芳烃收率及特定产品的选择性。综述了甲醇制芳烃反应中ZSM-5分子筛催化剂负载法、碱处理法、酸处理法和水热处理法等改性技术研究进展,以期达到工业化要求,最终实现甲醇制芳烃工艺的工业化发展。     

改性ZSM-5分子筛催化合成哌嗪

研究了不同金属离子改性得到的M-ZSM-5分子筛在以乙二胺(EDA)为原料合成哌嗪反应中的催化性能。通过NH3-TPD和BET法对催化剂进行表征,结果表明,经过离子交换后HZSM-5的骨架结构没有发生变化,仅仅是表面酸性发生了变化。重点考察了催化剂酸性对反应的影响,实验表明,提高弱酸和中强酸中心所占比例有利于哌嗪(PA)和三乙烯二胺(TEDA)生成。以Zn-ZSM-5和Zn/K-ZSM-5为催化剂,在常压,t=360℃,空速为0.25 g/(min.h),m(EDA)∶m(H2O)=4∶6的反应条件下,原料EDA的转化率分别为94.1%和82.6%;产物PA和TEDA的选择性分别为45.5%,42.1%和29.4%,50.1%。     

Modification of zsm-5 zeolite with trimethyl phosphite part 1. structure and acidity

In the present work we have studied the structure and the acidic properties of HZSM-5 zeolite modified with trimethyl phosphite. The modifications were carried out by using a chemical vapour deposition method as well as impregnation from n-octane solution. Both modification techniques resulted in materials with similar acidic properties. Trimethyl phosphite reacted with both Brönsted acid sites and terminal SiOH groups. The modifications resulted in the total elimination of strong Brönsted acid sites accompanied by the formation of new Brönsted type sites with decreased acid strength. However, the total acidity of the modified zeolites stayed relatively high. A possible structural transformation resulting from the phosphite modifications was proposed to be an insertion of phosphorus species between the structural aluminium- and silicon-oxygen tetrahedra. However, on the basis of ³¹P MAS NMR studies no evidence of the isomorphous substitution of structural T-atoms by phosphorus was found.     

Hydrogen back-spillover effects in the aromatization of ethylene on hybrid ZSM-5 catalysts

The involvement of hydrogen back-spillover is confirmed for the aromatization of ethylene. Using hydrogen monitoring during catalytic reactions with ethylene, it has been observed that the amount of hydrogen in the gaseous effluents is much more important on hybrid catalysts than on pure ZSM-5 zeolites. The active sites on ZnO based co-catalysts are believed to be partial reduction zinc sites created during the induction period. ZnO precipitate favors the release of hydrogen species as ethane. ZnO/Al₂O₃ co-precipitate favors hydrogen recombination.