Enhanced photocatalytic activity of highly transparent superhydrophilic doped TiO2 thin films for improving the self-cleaning property of solar panel covers

Undoped and metal doped nanocrystalline TiO₂ transparent thin films were synthesized on glass substrates via sol-gel/dip-coating method. TiO₂ thin film coatings can be applied to the surfaces of solar panels to impart self-cleaning properties to them. The structural and optical properties of few nanometer-thick films were characterized by XRD, SEM, CA, AFM, XPS, and UV–Vis spectrophotometry techniques. The stoichiometric TiO₂ films crystallized in anatase phase, with a particle size of ～100 nm, which were uniformly distributed on the surface. The prepared films with a roughness of ～1–5 nm, increased the hydrophilicity of the glass surface. Reducing the amount of Ti precursor (X) favored the improvement of film quality. To improve the photocatalytic activity of the TiO₂ thin film, it was doped with Ni, Cd, Mo, Bi and Sr metal ions. The effect of metal doping on the photocatalytic activity of the films was investigated using the degradation process of methylene blue (MB) dye as the model contaminant. Among the prepared coatings, the Sr–TiO₂ film showed the highest efficiency for MB degradation. It increased the dye degradation efficiency of the films under both UV and Vis lights. The kinetic investigations also showed that the degradation of MB by TiO₂ and M ? TiO₂ films obeyed the pseudo-first order kinetics.     

Two-Functional Direct Current Sputtered Silver-Containing Titanium Dioxide Thin Films

The article reports on structure, mechanical, optical, photocatalytic and biocidal properties of Ti–Ag–O films. The Ti–Ag–O films were reactively sputter-deposited from a composed Ti/Ag target at different partial pressures of oxygen on unheated glass substrate held on floating potential U _fl. It was found that addition of ~2 at.% of Ag into TiO₂ film has no negative influence on UV-induced hydrophilicity of TiO₂ film. Thick (~1,500 nm) TiO₂/Ag films containing (200) anatase phase exhibit the best hydrophilicity with water droplet contact angle (WDCA) lower than 10° after UV irradiation for 20 min. Thick (~1,500 nm) TiO₂/Ag films exhibited a better UV-induced hydrophilicity compared to that of thinner (~700 nm) TiO2/Ag films. Further it was found that hydrophilic TiO₂/Ag films exhibit a strong biocidal effect under both the visible light and the UV irradiation with 100% killing efficiency of Escherichia coli ATCC 10536 after UV irradiation for 20 min. Reported results show that single layer of TiO₂ with Ag distributed in its whole volume exhibits, after UV irradiation, simultaneously two functions: (1) excellent hydrophilicity with WDCA < 10° and (2) strong power to kill E. coli even under visible light due to direct toxicity of Ag.     

Photocatalytic decomposition of NO on titanium oxide thin film photocatalysts prepared by an ionized cluster beam technique

Transparent TiO₂ thin film photocatalysts were prepared on transparent porous Vycor glass (PVG) by an ionized cluster beam (ICB) method. The UV‐VIS absorption spectra of these films show specific interference fringes, indicating that uniform and transparent TiO₂ thin films are formed. The results of XRD measurements indicate that these TiO₂ thin films consist of both anatase and rutile structures. UV light (λ > 270 nm) irradiation of these TiO₂ thin films in the presence of NO led to the photocatalytic decomposition of NO into N₂, O₂ and N₂O. The reactivity of these TiO₂ thin films for the photocatalytic decomposition of NO is strongly dependent on the film thickness, i.e., the thinner the TiO₂ thin films, the higher the reactivity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Enhanced photocatalytic activity of Au-buffered TiO2 thin films prepared by radio frequency magnetron sputtering

Au-buffered TiO₂ thin films have been prepared by radio frequency magnetron sputtering method. The structural and morphological properties of the thin films were characterized by X-ray diffraction, scanning electron microscopy, and atomic force microscopy. The photocatalytic activity of the samples was evaluated by the photodecomposition of methylene blue. The Au-buffer thin layer placed between the TiO₂ thin films significantly enhanced photocatalytic activity by 50%. Annealing the Au-buffered TiO₂ thin film at 600 °C decreased the film roughness, but it increased the surface area and anatase crystalline size, enhancing the photocatalytic activity.     

A Novel Method for Preparing V-doped Titanium Dioxide Thin Film Photocatalysts with High Photocatalytic Activity Under Visible Light Irradiation

The liquid phase deposition (LPD) method was successfully used for preparing V-doped TiO₂ thin film photocatalysts. In this simple and easily-controlled process, V-doped anatase TiO₂ thin films were directly deposited on a soda lime glass substrate placed in an aqueous solution containing Ti- and V-fluoro complex ions, followed by annealing. The thin films were analyzed by XRD, XPS, UV-vis. V⁴⁺ ions were introduced into the lattice of TiO₂ through in-situ substituting Ti⁴⁺. The absorption edge of V-doped TiO₂ films shifted to visible light region. The highly efficient photocatalytic activity was verified by the decomposition of methylene blue under visible light irradiation.     

Effect of rapid thermal annealing on the structural and electrical properties of TiO2 thin films prepared by plasma enhanced CVD

Titanium oxide thin films were deposited on p-type Si(100), SiO₂/Si, and Pt/Si substrates by plasma enhanced chemical vapor deposition using high purity Ti(O-i-C₃H₇)₄ and oxygen. As-deposited amorphous TiO₂ thin films were treated by rapid thermal annealing (RTA) in oxygen ambient, and the effects of RTA conditions on the structural and electrical properties of TiO₂ films were studied in terms of crystallinity, microstructure, current leakage, and dielectric constant. The dominant crystalline structures after 600 and 800 ‡C annealing were an anatase phase for the TiO₂ film on SiO₂/Si and a rutile phase for the film on a Pt/Si substrate. The dielectric constant of the as-grown and annealed TiO₂ thin films increased depending on the substrate in the order of Si, SiO₂/Si, and Pt/ Si. The SiO₂ thin layer was effective in preventing the formation of titanium silicide at the interface and current leakage of the film. TEM photographs showed an additional growth of SiO_x from oxygen supplied from both SiO₂ and TiO₂ films when the films were annealed at 1000 ‡C in an oxygen ambient. Intensity analysis of Raman peaks also indicated that optimizing the oxygen concentration and the annealing time is critical for growing a TiO₂ film having high dielectric and low current leakage characteristics.     

Photocatalytic treatments on dental mirror surfaces using hydrolysis of titanium alkoxide

Anatase titanium dioxide (TiO₂) photocatalytic thin films were directly formed on glass slide and commercial dental mirror substrate surfaces by a hydrolysis of titanium alkoxide, and the hydrophilicity, the degree of oxidizing power and the transparency of the anatase TiO₂-coated substrate surfaces. The contact angles of water and the decomposition rates of methylene blue on the anatase TiO₂ photocatalytic thin films improved with the increasing duration of a tetraethyl orthotitanate (TEOT) hydrolysis, but they hardly changed for the longer duration. The reflectance of anatase TiO₂ photocatalytic thin films coated on glass slide substrate surfaces was higher as the duration of a TEOT hydrolysis increased. Similar tendencies concerning hydrophilicity and transparency were recognized in cases of commercial dental mirror substrate surfaces. A hydrolysis of titanium alkoxide obtained superhydrophilic and antibacterial treatments with excellent transparency on commercial dental mirror substrate surfaces.     

Photocatalytic Decomposition of Formic Acid Under Visible Light Irradiation Over V-ion-implanted TiO2 Thin Film Photocatalysts Prepared on Quartz Substrate by Ionized Cluster Beam (ICB) Deposition Method

Unique visible-light-responsive TiO₂ photocatalysts (λ>450 nm) were successfully developed by implantation of V ions into the TiO₂ thin films prepared on a quartz substrate by an ionized cluster beam (ICB) deposition method. After V ions implantation into TiO₂ thin film, the photocatalytic activity of the thin films for the decomposition of formic acid into CO₂ and H₂O was found to proceed efficiently under visible light irradiation longer than 450 nm. The TiO₂ thin film photocatalysts were characterized by XRD, UV-vis, XPS, FE-SEM and AFM.     

Fabrication of high-efficiency anatase TiO2 photocatalysts using electrospinning with ultra-violet treatment

In metal oxide nanofiber fabrication using the electrospinning method, heat treatment is performed at temperatures of 500°C or higher for crystallization and polymer desorption. Therefore, it is difficult to fabricate low-temperature phase metal oxides that crystallize at low temperatures. TiO₂, a representative metal oxide often used as photocatalysts, is known to have higher photocatalytic activity in the low-temperature phase (anatase structure) than in the high-temperature phase (rutile structure). Studies on the fabrication of TiO₂ anatase nanofibers using conventional electrospinning have reported disadvantages such as the partial expression of rutile structures and low crystallinity. This study developed an anatase TiO₂ nanofiber as a high-efficiency catalyst based on the electrospinning method and a residual organic matter cleaning method that employs ultra-violet (UV) light. We fabricated nanofibers using the electrospinning method and implemented TiO₂ nanofibers with the anatase structure through heat treatment at 260°C. Residual organics remaining after heat treatment of the fabricated crystalized TiO₂ nanofibers were removed by exposing them to UV light, thereby improving photocatalytic efficiency. The photocatalytic efficiency of the fabricated TiO₂ nanofibers was confirmed through a methylene blue (MB) decomposition experiment under visible light irradiation. The photocatalytic efficiency (time taken for the concentration of the MB solution to reach 50%) of the UV-treated TiO₂ nanofibers was approximately six times higher than of P25 and the heat-treated nanofibers.     

Role of phase content on the photocatalytic performance of TiO2 coatings deposited by suspension plasma spray

In this work, suspension plasma spraying (SPS) with different hydrogen (H₂) flow rates was employed to produce TiO₂ coatings with various phase contents, oxygen contents, and roughnesses. To eliminate the role of the morphology and oxygen content on the photocatalytic activity, all coatings were polished to reach the same roughness followed by heat-treatment at 550 °C in air for 48 h. Then coatings were analyzed by X-ray diffractometer (XRD), confocal laser microscope, scanning electron microscope (SEM), UV–visible spectrometer, Raman microscope, and thermogravimetric analyzer. The XRD data indicated that the percentage of anatase decreased as function of H₂ flow rates, and almost 46% of anatase transformed to rutile during SPS process at the highest H₂ flow rate. Moreover, the photocatalytic performance was evaluated by monitoring the degradation of methylene blue under visible light irradiation, and the results indicated that anatase phase positively enhances the photocatalytic activity of TiO₂ coatings.     

Wetting angles and photocatalytic activities of illuminated TiO2 thin films

TiO₂ thin films have been prepared by physical vapour deposition (PVD) and plasma enhanced chemical vapour deposition (PECVD) to study the UV-induced photo-activity of this material. Wetting angle variations and photo-catalytic activity for the degradation of dyes upon UV illumination have been compared for thin films with different crystalline structure (amorphous, rutile and anatase), microstructure (columnar, compact, etc.) and porosities as estimated from the values of their refraction indices and their direct assessment with a quartz crystal monitor. The surface of the thin films became superhydrophilic upon UV light irradiation and then it recovered its original state by keeping the samples in the dark. Wetting angle decays follow very similar kinetics for amorphous and crystalline films, independently of their actual porosities. By contrast the photo-catalytic activity was very dependent on the crystalline structure of the films (anatase > rutile > amorphous) and on their porosities. The different behaviour depicted by the films with regard to these two properties suggests that they respond to different though related mechanisms and that they cannot be considered as equivalent when trying to prove the photo-activity of TiO₂.     

Photocatalytic Water Splitting on Visible Light-responsive TiO2 Thin Films Prepared by a RF Magnetron Sputtering Deposition Method

The development of visible light-responsive TiO₂ (Vis-TiO₂) thin films has been achieved by applying a radio-frequency magnetron sputtering deposition (RF-MS) method. Pt-loaded Vis-TiO₂ thin films act as photocatalysts to decompose water involving sacrificial reagent such as methanol or silver nitrate even under visible light (λ ≧ 420 nm) irradiation. It was also found that Pt-loaded Vis-TiO₂ thin films decompose pure water into H₂ and O₂ stoichiometrically under light irradiation of wavelengths longer than 390 nm. Vis-TiO₂ thin films exhibit columnar structures perpendicular to the substrate and a declined composition of the O/Ti ratio from the surface (O/Ti = 2.00) to bottom (O/Ti = 1.93). This unique structure (anisotropic structure) of Vis-TiO₂ can be considered an important factor in the modification of the electronic properties of Vis-TiO₂ thin films, enabling the absorption of visible light. Furthermore, the effect of the Pt loadings on the photocatalytic activity of the TiO₂ thin films was investigated and the optimum Pt loading was determined to be 21 μ g/cm² as Pt metal     

Preparation, crystal structure, and photocatalytic activity of TiO2 films by chemical vapor deposition

Photocatalytic activities of TiO₂ films were experimentally studied. TiO₂ films with different crystal structures (amorphous, anatase, rutile) were prepared by a Low Pressure Metal Organic Chemical Vapor Deposition (LPMOCVD) at different reaction temperatures and also by a Sol-Gel method using TTIP (Titanium Tetra Iso-Pro-poxyde). The Effect of CVD preparation method, CVD reaction conditions, crystal structure and wave-length of UV light on the photocatalytic decomposition rate of methylene blue in aqueous solution were studied. First, the characteristics of CVD preparation of TiO₂ films, such as the CVD film growth rate, crystal structure and morphology of the grown TiO₂ films, were experimentally studied as a function of CVD reaction temperature. Secondly, photocatalytic activities of TiO₂ films were evaluated by using two types of photo-reactors. The results indicated that TiO₂ films prepared by CVD exhibit higher photocatalytic activity than a catalyst prepared by the Sol-Gel method. Among the CVD grown TiO₂ films, anatase and rutile showed high photocatalytic activities. However, amorphous TiO₂ films showed lower activities. The activity of the photocatalysts of anatase films was excellent under all types of UV-lamps. The activity of CVD-prepared anatase films was four to seven times higher than that of photocatalyst films prepared by the Sol-Gel method.     

Large-scale preparation of nanoporous TiO2 film on titanium substrate with improved photoelectrochemical performance

Fabrication of three-dimensional TiO₂ films on Ti substrates is one important strategy to obtain efficient electrodes for energy conversion and environmental applications. In this work, we found that hierarchical porous TiO₂ film can be prepared by treating H₂O₂ pre-oxidized Ti substrate in TiCl₃ solution followed by calcinations. The formation process is a combination of the corrosion of Ti substrate and the oxidation hydrolysis of TiCl₃. According to the characterizations by scanning electron microscopy (SEM), X-ray diffraction (XRD), and diffuse reflectance spectroscopy (DRS), the anatase phase TiO₂ films show porous morphology with the smallest diameter of 20 nm and possess enhanced optical absorption properties. Using the porous film as a working electrode, we found that it displays efficient activity for photoelectrocatalytic decolorization of rhodamine B (RhB) and photocurrent generation, with a photocurrent density as high as 1.2 mA/cm². It represents a potential method to fabricate large-area nanoporous TiO₂ film on Ti substrate due to the scalability of such chemical oxidation process.     

Facile preparation of Na-free anatase TiO2 film with highly photocatalytic activity on soda-lime glass

Na-free anatase TiO₂ film was prepared on soda-lime glass (SL-glass) from a TiF₄ aqueous solution upon addition of boric acid at 60 °C. It was found that the as-prepared TiO₂ film before calcination showed a higher photocatalytic activity than the calcined sample (500 °C). This could be attributed to the fact that the calcined TiO₂ film contained decent Na⁺ ions, which was diffused from the SL-glass substrate into the TiO₂ film during calcination, resulting in the decrease of photocatalytic activity.     

Optimization of N-doped TiO2 multifunctional thin layers by low frequency PECVD process

A one-step low-frequency Plasma Enhanced Chemical Vapor Deposition (PECVD) process, operating at temperature as low as 350 °C, has been implemented to prepare single-oriented pure and N-doped anatase films. The layers have been synthesized using titanium isopropoxide as a precursor, and NH₃ as a doping agent. Optimized PECVD conditions have enabled to obtain homogeneous micro-columnar porous thin films with thicknesses close to 500 nm. Depth profiling XPS analyses have proved the nitrogen incorporation into TiO₂ lattice after ammonia introduction in the deposition chamber. As another proof of N-doping, Raman and XRD peaks shifting have been observed. Such thin films have been demonstrated as efficient photocatalytic materials which activity region can be tailored from UV to visible region by adjusting the proportion of doping agent in the plasma phase. Due to their microstructural and photocatalytic properties, the prepared thin layers should have an interest as anode materials in solar water splitting cells.     

Synthesis, characterization and photocatalytic properties of sol-gel TiO2 films

The application of heterogeneous photocatalysis is described as an advanced oxidation process (AOP) for the degradation of the diazo reactive dye using immobilized TiO₂ as a photocatalyst. Starting TiO₂ solutions were prepared with and without the addition of polyethylene glycol (PEG) and TiO₂ films were directly deposited on a borosilicate glass substrate using the sol-gel dip-coating method. The surface morphology and the nanoscale roughness of TiO₂ films were studied by means of atomic force microscopy (AFM). Structural properties of TiO₂ were identified by X-ray diffraction (XRD). The decomposition behaviour of organic compounds from the gels was investigated using thermal gravimetry (TG) and differential scanning calorimetry (DSC). Photocatalytic activities of TiO₂ films in the process of degradation of the commercial diazo textile dye Congo red (CR), used as a model pollutant, were monitored by means of UV/vis spectrophotometry. The kinetics of the degradation of the CR dye was described with the Langmuir-Hinshelwood (L-H) kinetic model.The addition of PEG to the TiO₂ solution resulted in the changes in the film surface morphology, and affected the ratio of anatase-rutile crystal phases and the photocatalytic activity of TiO₂. The TiO₂ film prepared with PEG is characterized by higher roughness parameters (R_a, R_max, R_q, R_z and Z_max), a lower amount of the rutile phase of TiO₂, a higher amount of the anatase phase of TiO₂ and a better photocatalytic activity compared to the TiO₂ film without the addition of PEG.     

Visible light photocatalytic activity of TiO2/heat‐treated PVC film

BACKGROUND: Semiconductor TiO₂ has been investigated extensively due to its chemical stability, nontoxicity and inexpensiveness. However, the wide band gap of anatase TiO₂ (about 3.2 eV) only allows it to absorb UV light. TiO₂ nanoparticles modified by conditional conjugated polymers show excellent photocatalytic activity under visible light. However, these conjugated polymers are not only expensive, but also difficult to process. Polyvinyl chloride (PVC) was heat‐treated at high temperature to remove HCl and a C?C conjugated chain structure was obtained. When TiO₂ nanoparticles were dispersed into the conjugated polymer film derived from PVC, this composites film exhibited high visible light photocatalytic activity. RESULTS: The photocatalytic activity of TiO₂/heat‐treated PVC (HTPVC) film was investigated by degrading Rhodamine B (RhB) under visible light irradiation. The photodegradation of RhB follows apparent first‐order kinetics. The rate constants of RhB photodegradation in the presence of the TiO₂/HTPVC films with different mass content of TiO₂ are 16–56 and 4–14 times that obtained in the presence of the pure HTPVC and TiO₂/polymethyl methacrylate (PMMA) composite film, respectively. The TiO₂/HTPVC film showed excellent photocatalytic activity and stability after 10 cycles under visible light irradiation. CONCLUSION: TiO₂/HTPVC film exhibits high visible light photocatalytic activity and stability. Copyright © 2012 Society of Chemical Industry     

Effects of V and Zn codoping on the microstructures and photocatalytic activities of nanocrystalline TiO2 films

To enhance the photocatalytic activity of TiO₂, V and Zn co-doped TiO₂ films were synthesized by the sol–gel method. The experimental results indicated that the films were composed of round-like nano-particles or aggregates. V and Zn codoping could not only obviously increase the specific surface area of TiO₂ but also result in the narrowed band gap of TiO₂ sample. The photocatalytic activities of the TiO₂ films were evaluated by the photocatalytic decomposition of organic dyes in aqueous solution. Compared with un-doped TiO₂ film or single doped TiO₂ film, V and Zn co-doped TiO₂ film exhibited excellent photocatalytic activities under both UV light and visible light. The improvement mechanism by V and Zn codoping was also discussed.     

Optical properties of TiO2 nanoceramic films as a function of N–Al co-doping

The N-doped TiO₂, Al-doped TiO₂ and N–Al co-doped TiO₂ films had the similar structure to that of the TiO₂ film and corresponded to nanocrystalline anatase. By N and/or Al doping, the TiO₂ film became more stoichiometric and the nanocrystallinity was enhanced, especially N–Al co-doping. The optical transmission of N–Al co-doped TiO₂ film was the highest because of the lowest surface roughness and the lowest porosity. The nonlinear refractive index of N–Al co-doped TiO₂ film on the glass substrate was measured by Moiré deflectometry, and was of the order of 10⁻⁸ cm² W⁻¹. By N–Al co-doping, the TiO₂ nanoceramic film exhibited highest linear refractive index, lowest stress and lowest stress-optical coefficient.