Well-ordered polymer nano-fibers with self-cleaning property by disturbing crystallization process

Bionic self-cleaning surfaces with well-ordered polymer nano-fibers are firstly fabricated by disturbing crystallization during one-step coating-curing process. Orderly thin (100 nm) and long (5–10 μm) polymer nano-fibers with a certain direction are fabricated by external macroscopic force (F_blow) interference introduced by H₂ gas flow, leading to superior superhydrophobicity with a water contact angle (WCA) of 170° and a water sliding angle (WSA) of 0-1°. In contrast, nano-wires and nano-bridges (1–8 μm in length/10-80 nm in width) are generated by “spinning/stretching” under internal microscopic force (F_T) interference due to significant temperature difference in the non-uniform cooling medium. The findings provide a novel theoretical basis for controllable polymer “bionic lotus” surface and will further promote practical application in many engineering fields such as drag-reduction and anti-icing.     

Effect of annealing temperature on wettability of TiO2 nanotube array films

Highly ordered TiO₂ nanotube array (TN) films were prepared by anodization of titanium foil in a mixed electrolyte solution of glycerin and NH₄F and then annealed at 200°C, 400°C, 600°C, and 800°C, respectively. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), water contact angle (WCA), and photoluminescence (PL). It was found that low temperature (below 600°C) has no significant influence on surface morphology, but the diameter of the nanotube increases from 40 to 50 nm with increasing temperature. At 800°C, the nanotube arrays are completely destroyed and only dense rutile film is observed. Samples unannealed and annealed at 200°C are amorphous. At 400°C, anatase phase appears. At 600°C, rutile phase appears. At 800°C, anatase phase changes into rutile phase completely. The wettability of the TN films shows that the WCAs for all samples freshly annealed at different temperatures are about 0°. After the annealed samples have been stored in air for 1 month, the WCAs increase to 130°, 133°, 135°, 141°, and 77°, respectively. Upon ultraviolet (UV) irradiation, they exhibit a significant transition from hydrophobicity to hydrophilicity. Especially, samples unannealed and annealed at 400°C show high photoinduced hydrophilicity.     

Preparation of HMDS-modified silica/polyacrylate hydrophobic hard coatings on PMMA substrates

Colloidal silica nanoparticles synthesized from tetraethoxysiliane via a sol–gel process were surface modified by 3-(trimethoxysilyl)propyl methacrylate (MSMA) and 1,1,1,3,3,3-hexamethyldisilazane (HMDS). MSMA acted both as a C=C provider and a coupling agent, whereas HMDS was used to prevent particle aggregation and engender hydrophobicity. The modified silica particles (HMSiO₂) were UV-cured together with the crosslinking agent, dipentaerythritol hexa-acrylate (DPHA) to form coatings on poly(methyl methacrylate) (PMMA) substrates. Dynamic light scattering of the synthesized sols indicated that the average size of HMSiO₂ was ca. 10 nm, consistent with that obtained from TEM imaging. FTIR spectroscopic analyses demonstrated chemical attachment of HMDS to the silica particles. The cured coatings were characterized in terms of water contact angle, light transmittance, hardness, abrasion resistance, and surface morphology. It was found that hydrophobicity of the coatings increased while light transmittance and hardness decreased with increasing HMDS content. DPHA played the role of providing mechanical strength and adherence; however, the coatings became lightly hazy when the weight ratio of DPHA/silica fell in the range 0.3–0.7. In the optimal case, a hard coating (4H) with water contact angle of 108° and transmittance of ~100% (vs PMMA) had been obtained at the DPHA content of 10 wt%.     

Cytotoxicity Study of UV-Laser-Irradiated PLLA Surfaces Subjected to Bio-Ceramisation: A New Way towards Implant Surface Modification

In this research we subjected samples of poly(L-lactide) (PLLA) extruded film to ultraviolet (193 nm ArF excimer laser) radiation below the ablation threshold. The modified film was immersed in Simulated Body Fluid (SBF) at 37 °C for 1 day or 7 days to obtain a layer of apatite ceramic (CaP) coating on the modified PLLA surface. The samples were characterized by means of optical profilometry, which indicated an increase in average roughness (Ra) from 25 nm for the unmodified PLLA to over 580 nm for irradiated PLLA incubated in SBF for 1 day. At the same time, the water contact angle decreased from 78° for neat PLLA to 35° for irradiated PLLA incubated in SBF, which suggests its higher hydrophilicity. The obtained materials were investigated by means of cell response fibroblasts (3T3) and macrophage-like cells (RAW 264.7). Properties of the obtained composites were compared to the unmodified PLLA film as well as to the UV-laser irradiated PLLA. The activation of the PLLA surface by laser irradiation led to a distinct increase in cytotoxicity, while the treatment with SBF and the deposition of apatite ceramic had only a limited preventive effect on this harmful impact and depended on the cell type. Fibroblasts were found to have good tolerance for the irradiated and ceramic-covered PLLA, but macrophages seem to interact with the substrate leading to the release of cytotoxic products.     

Stable superhydrophobic surface of hierarchical carbon nanotubes on Si micropillar arrays

It is of great importance to construct a stable superhydrophobic surface with low sliding angle (SA) for various applications. We used hydrophobic carbon nanotubes (CNTs) to construct the superhydrophobic hierarchical architecture of CNTs on silicon micropillar array (CNTs/Si-μp), which have a large contact angle of 153° to 155° and an ultralow SA of 3° to 5°. Small water droplets with a volume larger than 0.3 μL can slide on the CNTs/Si-μp with a tilted angle of approximately 5°. The CNTs growing on planar Si wafer lose their superhydrophobic properties after exposing to tiny water droplets. However, the CNTs/Si-μp still show superhydrophobic properties even after wetting using tiny water droplets. The CNTs/Si-μp still have a hierarchical structure after wetting, resulting in a stable superhydrophobic surface.     

A Novel Strategy for Creating an Antibacterial Surface Using a Highly Efficient Electrospray-Based Method for Silica Deposition

Adhesion of bacteria on biomedical implant surfaces is a prerequisite for biofilm formation, which may increase the chances of infection and chronic inflammation. In this study, we employed a novel electrospray-based technique to develop an antibacterial surface by efficiently depositing silica homogeneously onto polyethylene terephthalate (PET) film to achieve hydrophobic and anti-adhesive properties. We evaluated its potential application in inhibiting bacterial adhesion using both Gram-negative Escherichia coli (E. coli) and Gram-positive Staphylococcus aureus (S. aureus) bacteria. These silica-deposited PET surfaces could provide hydrophobic surfaces with a water contact angle greater than 120° as well as increased surface roughness (root mean square roughness value of 82.50 ± 16.22 nm and average roughness value of 65.15 ± 15.26 nm) that could significantly reduce bacterial adhesion by approximately 66.30% and 64.09% for E. coli and S. aureus, respectively, compared with those on plain PET surfaces. Furthermore, we observed that silica-deposited PET surfaces showed no detrimental effects on cell viability in human dermal fibroblasts, as confirmed by MTT (3-(4,5-dimethylthiazol-2-yl)-2,5 diphenyl tetrazolium bromide and live/dead assays. Taken together, such approaches that are easy to synthesize, cost effective, and efficient, and could provide innovative strategies for preventing bacterial adhesion on biomedical implant surfaces in the clinical setting.     

Robust super-hydrophobic ceramic coating on alumina with water and dirt repelling properties

Artificial super-hydrophobic surfaces are required for various applications. The super-hydrophobic surfaces are usually made by applying a low surface-energy organic coating on a highly textured substrate. A major problem with the as-created surfaces is their poor durability. This problem is even severer for the surfaces created by applying the organic coating on inorganic substrates. The present study reports for the first time the all-inorganic super-hydrophobic surface created by modifying the inorganic substrates with polymer-derived inorganic coating. A polydimethylsiloxane (PDMS) film was applied to an alumina substrate having flower-like hierarchal micro-nano surface texture, and then subjected to pyrolysis at 400°C in a nonoxidizing atmosphere. As a result, a Si_xC_yO_z ceramic coating with low-surface energy methyl groups was formed on the alumina substrate. The as-modified alumina exhibited super-hydrophobicity with a water contact angle of 170° and a sliding angle of 5°. The super-hydrophobicity was well retained after abrasion with sandpaper and exposure to boiling water and acidic solution. The super-hydrophobic alumina demonstrated desired water repelling and self-cleaning function. The method explored in this study could also be used for super-hydrophobic surface modification of other inorganic materials such as glass and metals.     

Characterization and application of electrospun alumina nanofibers

Alumina nanofibers were prepared by a technique that combined the sol–gel and electrospinning methods. The solution to be electrospun was prepared by mixing aluminum isopropoxide (AIP) in ethanol, which was then refluxed in the presence of an acid catalyst and polyvinylpyrolidone (PVP) in ethanol. The characterization results showed that alumina nanofibers with diameters in the range of 102 to 378 nm were successfully prepared. On the basis of the results of the XRD and FT-IR, the alumina nanofibers calcined at 1,100°C were identified as comprising the α-alumina phase, and a series of phase transitions such as boehmite → γ-alumina → α-alumina were observed from 500°C to 1,200°C. The pore size of the obtained γ-alumina nanofibers is approximately 8 nm, and it means that they are mesoporous materials. The kinetic study demonstrated that MO adsorption on alumina nanofibers can be seen that the pseudo-second-order kinetic model fits better than the pseudo-first-order kinetic model.     

Vascular Polyurethane Prostheses Modified with a Bioactive Coating—Physicochemical,Mechanical and Biological Properties

This study describes a method for the modification of polyurethane small-diameter (5 mm) vascular prostheses obtained with the phase inversion method. The modification process involves two steps: the introduction of a linker (acrylic acid) and a peptide (REDV and YIGSR). FTIR and XPS analysis confirmed the process of chemical modification. The obtained prostheses had a porosity of approx. 60%, Young’s Modulus in the range of 9–11 MPa, and a water contact angle around 40°. Endothelial (EC) and smooth muscle (SMC) cell co-culture showed that the surfaces modified with peptides increase the adhesion of ECs. At the same time, SMCs adhesion was low both on unmodified and peptide-modified surfaces. Analysis of blood-materials interaction showed high hemocompatibility of obtained materials. The whole blood clotting time assay showed differences in the amount of free hemoglobin present in blood contacted with different materials. It can be concluded that the peptide coating increased the hemocompatibility of the surface by increasing ECs adhesion and, at the same time, decreasing platelet adhesion. When comparing both types of peptide coatings, more promising results were obtained for the surfaces coated with the YISGR than REDV-coated prostheses.     

Moisture absorption into ultrathin hydrophilic polymer films on different substrate surfaces

Moisture absorption into ultrathin poly(vinyl pyrrolidone) (PVP) films with varying thickness was examined using X-ray reflectivity (XR) and quartz crystal microbalance (QCM) measurements. Two different surfaces were used for the substrate: a hydrophilic silicon oxide (SiO_x) and a hydrophobic hexamethyldisilazane (HMDS) treated silicon oxide surface. The total equilibrium moisture absorption (solubility) was insensitive to the surface treatment in the thickest films (≈150 nm). However, strong reductions in the equilibrium uptake with decreasing PVP film thickness were observed on the HMDS surfaces, while the SiO_x surface exhibited thickness independent equilibrium absorption. The decreased absorption with decreasing film thickness is attributed a depletion layer of water near the polymer/HMDS interface, arising from hydrophobic interactions between the surface and water. The diffusivity of water decreased when the film thickness was less than 60 nm, independent of the surface treatment. Changes in the properties of ultrathin polymer films occur even in plasticized films containing nearly 50% water.     

Laser Direct Writing via Two-Photon Polymerization of 3D Hierarchical Structures with Cells-Antiadhesive Properties

We report the design and fabrication by laser direct writing via two photons polymerization of innovative hierarchical structures with cell-repellency capability. The structures were designed in the shape of “mushrooms”, consisting of an underside (mushroom’s leg) acting as a support structure and a top side (mushroom’s hat) decorated with micro- and nanostructures. A ripple-like pattern was created on top of the mushrooms, over length scales ranging from several µm (microstructured mushroom-like pillars, MMP) to tens of nm (nanostructured mushroom-like pillars, NMP). The MMP and NMP structures were hydrophobic, with contact angles of (127 ± 2)° and (128 ± 4)°, respectively, whereas flat polymer surfaces were hydrophilic, with a contact angle of (43 ± 1)°. The cell attachment on NMP structures was reduced by 55% as compared to the controls, whereas for the MMP, a reduction of only 21% was observed. Moreover, the MMP structures preserved the native spindle-like with phyllopodia cellular shape, whereas the cells from NMP structures showed a round shape and absence of phyllopodia. Overall, the NMP structures were more effective in impeding the cellular attachment and affected the cell shape to a greater extent than the MMP structures. The influence of the wettability on cell adhesion and shape was less important, the cellular behavior being mainly governed by structures’ topography.     

Surfaces with Adjustable Features—Effective and Durable Materials for Water Desalination

Materials based on PVDF with desirable and controllable features were successfully developed. The chemistry and roughness were adjusted to produce membranes with improved transport and separation properties. Membranes were activated using the novel piranha approach to generate OH-rich surfaces, and finally furnished with epoxy and long-alkyl moieties via stable covalent attachment. The comprehensive materials characterization provided a broad spectrum of data, including morphology, textural, thermal properties, and wettability features. The defined materials were tested in the air-gap membrane distillation process for desalination, and improvement compared with pristine PVDF was observed. An outstanding behavior was found for the PVDF sample equipped with long-alkyl chains. The generated membrane showed an enhancement in the transport of 58–62% compared to pristine. A relatively high contact angle of 148° was achieved with a 560 nm roughness, producing a highly hydrophobic material. On the other hand, it was possible to tone the hydrophobicity and significantly reduce adhesion work. All materials were highly stable during the long-lasting separation process and were characterized by excellent effectiveness in water desalination.     

Unpatterned Bioactive Poly(Butylene 1,4-Cyclohexanedicarboxylate)-Based Film Fast Induced Neuronal-Like Differentiation of Human Bone Marrow-Mesenchymal Stem Cells

Herein, we present poly(butylene 1,4-cyclohexanedicarboxylate) (PBCE) films characterized by an unpatterned microstructure and a specific hydrophobicity, capable of boosting a drastic cytoskeleton architecture remodeling, culminating with the neuronal-like differentiation of human bone marrow-mesenchymal stem cells (hBM-MSCs). We have used two different filming procedures to prepare the films, solvent casting (PBCE) and compression-moulding (PBCE*). PBCE film had a rough and porous surface with spherulite-like aggregations (Ø = 10–20 μm) and was characterized by a water contact angle = 100°. PBCE* showed a smooth and continuous surface without voids and visible spherulite-like aggregations and was more hydrophobic (WCA = 110°). Both surface characteristics were modulated through the copolymerization of different amounts of ether-oxygen-containing co-units into PBCE chemical structure. We showed that only the surface characteristics of PBCE-solvent-casted films steered hBM-MSCs toward a neuronal-like differentiation. hBM-MSCs lost their canonical mesenchymal morphology, acquired a neuronal polarized shape with a long cell protrusion (≥150 μm), expressed neuron-specific class III β-tubulin and microtubule-associated protein 2 neuronal markers, while nestin, a marker of uncommitted stem cells, was drastically silenced. These events were observed as early as 2-days after cell seeding. Of note, the phenomenon was totally absent on PBCE* film, as hBM-MSCs maintained the mesenchymal shape and behavior and did not express neuronal/glial markers.     

Cellular Behavior of Human Adipose-Derived Stem Cells on Wettable Gradient Polyethylene Surfaces

Appropriate surface wettability and roughness of biomaterials is an important factor in cell attachment and proliferation. In this study, we investigated the correlation between surface wettability and roughness, and biological response in human adipose-derived stem cells (hADSCs). We prepared wettable and rough gradient polyethylene (PE) surfaces by increasing the power of a radio frequency corona discharge apparatus with knife-type electrodes over a moving sample bed. The PE changed gradually from hydrophobic and smooth surfaces to hydrophilic (water contact angle, 90º to ~50º) and rough (80 to ~120 nm) surfaces as the power increased. We found that hADSCs adhered better to highly hydrophilic and rough surfaces and showed broadly stretched morphology compared with that on hydrophobic and smooth surfaces. The proliferation of hADSCs on hydrophilic and rough surfaces was also higher than that on hydrophobic and smooth surfaces. Furthermore, integrin beta 1 gene expression, an indicator of attachment, and heat shock protein 70 gene expression were high on hydrophobic and smooth surfaces. These results indicate that the cellular behavior of hADSCs on gradient surface depends on surface properties, wettability and roughness.     

Antireflective silicon nanostructures with hydrophobicity by metal-assisted chemical etching for solar cell applications

We present broadband antireflective silicon (Si) nanostructures with hydrophobicity using a spin-coated Ag ink and by subsequent metal-assisted chemical etching (MaCE). Improved understanding of MaCE, by conducting parametric studies on optical properties, reveals a design guideline to achieve considerably low solar-weighted reflectance (SWR) in the desired wavelength ranges. The resulting Si nanostructures show extremely low SWR (1.96%) and angle-dependent SWR (<4.0% in the range of 0° to 60°) compared to that of bulk Si (SWR, 35.91%; angle-dependent SWR, 37.11%) in the wavelength range of 300 to 1,100 nm. Relatively large contact angle (approximately 102°) provides a self-cleaning capability on the solar cell surface.     

Reduction in thermal conductivity of Bi thin films with high-density ordered nanoscopic pores

We prepared two-dimensional Bi thin films with high-density ordered nanoscopic pores by e-beam evaporation of Bi metal. For this structure, we used polystyrene beads ranging from 200 to 750 nm in diameter as an etch mask. The typical hole and neck sizes of the Bi thin films with approximately 50 nm in thickness on SiO₂/Si substrates were in the range of 135 to 490 nm and 65 to 260 nm, respectively. By measuring the thermal characteristics through a 3ω technique, we found that the thermal conductivities of nanoporous Bi thin films are greatly suppressed compared with those of corresponding bulk materials. With a decrease in pore size to approximately 135 nm, the thermal conductivity decreased significantly to approximately 0.46 W/m·K at 300 K.     

Engineering optical properties of gold-coated nanoporous anodic alumina for biosensing

The effect in the Fabry-Pérot optical interferences of nanoporous anodic alumina films coated with gold is studied as a function of the porosity and of the gold thickness by means of reflectance spectroscopy. Samples with porosities between 14 and 70% and gold thicknesses (10 and 20 nm) were considered. The sputtering of gold on the nanoporous anodic alumina (NAA) films results in an increase of the fringe intensity of the oscillations in the spectra resulting from Fabry-Pérot interferences in the porous layer, with a reduction in the maximum reflectance in the UV-visible region. For the thicker gold layer, sharp valleys appear in the near-infrared (IR) range that can be useful for accurate spectral shift measurements in optical biosensing. A theoretical model for the optical behavior has also been proposed. The model shows a very good agreement with the experimental measurements, what makes it useful for design and optimization of devices based on this material. This material capability is enormous for using it as an accurate and sensitive optical sensor, since gold owns a well-known surface chemistry with certain molecules, most of them biomolecules.     

Study and characterization of porous copper oxide produced by electrochemical anodization for radiometric heat absorber

The aim of this work is to optimize the different parameters for realization of an absorbing cavity to measure the incident absolute laser energy. Electrochemical oxidation is the background process that allowed the copper blackening. A study of the blackened surface quality was undertaken using atomic force microscopy (AFM) analysis and ultraviolet-visible-infrared spectrophotometry using a Shimadzu spectrophotometer. A two-dimensional and three-dimensional visualization by AFM of the formed oxide coating showed that the copper surfaces became porous after electrochemical etching with different roughness. This aspect is becoming more and more important with decreasing current density anodization. In a 2 mol L ^-1 of NaOH solution, at a temperature of 90°C, and using a 16 mA cm² constant density current, the copper oxide formed has a reflectivity of around 3% in the spectral range between 300 and 1,800 nm. Using the ‘mirage effect’ technique, the obtained Cu₂O diffusivity and thermal conductivity are respectively equal to (11.5 ± 0.5) 10 to 7 m² s^-1 and (370 ± 20) Wm^-1 K^-1. This allows us to consider that our Cu₂O coating is a good thermal conductor. The results of the optical and thermal studies dictate the choice of the cavity design. The absorbing cavity is a hollow cylinder machined to its base at an angle of 30°. If the included angle of the plane is 30° and the interior surface gives specular reflection, an incoming ray parallel to the axis will undergo five reflections before exit. So the absorption of the surface becomes closely near 0.999999.     

Engineering durable hydrophobic surfaces on porous alumina ceramics using in-situ formed inorganic-organic hybrid nanoparticles

Hydrophobic surfaces are required for a variety of applications owing to their water repellent and self-cleaning properties. In this work, we present a novel approach to prepare durable hydrophobic surfaces on porous ceramics. A polydimethylsiloxane (PDMS) film was applied to a porous alumina wafer, followed by pyrolysis at 400 °C in a non-oxidizing atmosphere (H₂:N₂ = 5:95), giving rise to nanoparticles. In these particles, Si, C and O elements formed amorphous networks to which methyl groups that had survived the pyrolysis were bonded. The as-modified porous alumina wafer was hydrophobic with a water contact angle of 136°, which is attributed to the presence of the methyl groups. The hydrophobicity was maintained after immersion in aqueous solutions in a pH range of 2–12 and acetone. The hydrophobicity was also retained after exposure to temperatures as high as 450 °C in an oxidative atmosphere (air) and after mechanical abrasion with sandpaper. The hydrophobic porous alumina ceramics developed in the present study are promising for use as membranes in various separation processes.     

Key Properties of a Bioactive Ag-SiO2/TiO2 Coating on NiTi Shape Memory Alloy as Necessary at the Development of a New Class of Biomedical Materials

Recent years have seen the dynamic development of methods for functionalizing the surface of implants using biomaterials that can mimic the physical and mechanical nature of native tissue, prevent the formation of bacterial biofilm, promote osteoconduction, and have the ability to sustain cell proliferation. One of the concepts for achieving this goal, which is presented in this work, is to functionalize the surface of NiTi shape memory alloy by an atypical glass-like nanocomposite that consists of SiO₂-TiO₂ with silver nanoparticles. However, determining the potential medical uses of bio(nano)coating prepared in this way requires an analysis of its surface roughness, tribology, or wettability, especially in the context of the commonly used reference coat-forming hydroxyapatite (HAp). According to our results, the surface roughness ranged between (112 ± 3) nm (Ag-SiO₂)—(141 ± 5) nm (HAp), the water contact angle was in the range (74.8 ± 1.6)° (Ag-SiO₂)—(70.6 ± 1.2)° (HAp), while the surface free energy was in the range of 45.4 mJ/m² (Ag-SiO₂)—46.8 mJ/m² (HAp). The adhesive force and friction coefficient were determined to be 1.04 (Ag-SiO₂)—1.14 (HAp) and 0.247 ± 0.012 (Ag-SiO₂) and 0.397 ± 0.034 (HAp), respectively. The chemical data showed that the release of the metal, mainly Ni from the covered NiTi substrate or Ag from Ag-SiO₂ coating had a negligible effect. It was revealed that the NiTi alloy that was coated with Ag-SiO₂ did not favor the formation of E. coli or S. aureus biofilm compared to the HAp-coated alloy. Moreover, both approaches to surface functionalization indicated good viability of the normal human dermal fibroblast and osteoblast cells and confirmed the high osteoconductive features of the biomaterial. The similarities of both types of coat-forming materials indicate an excellent potential of the silver-silica composite as a new material for the functionalization of the surface of a biomaterial and the development of a new type of functionalized implants.