Deposition and ablation resistance of HfC-based coatings prepared on SiC-coated C/C composites by supersonic atmospheric plasma spraying

In order to improve the ablation properties of C/C composites, HfC-based coatings with different mass ratios of SiC were deposited on the surface of SiC-coated carbon/carbon composites by supersonic atmospheric plasma spraying. The morphologies and microstructures of the HfC-based coatings were characterised. The ablation resistance test was carried out by oxyacetylene torch. The results show that the as-prepared coatings are multiphase coatings consisting of HfC, HfO₂, SiC and SiO₂. The structure of different coatings is dense. After ablation for 60?s, the ablation centre region of coating is smooth without obvious microcrack and pinhole, and no interlaminar crack can be observed at the cross-section. An Hf–Si–O compound oxide layer is generated on the surface of coating, which is beneficial for protecting the C/C composites from being ablated. Meanwhile, the further generated HfSiO₄ can play a pinning effect, which can prevent crack extension.     

Bimodal microstructure ZrB2-MoSi2 coating prepared by atmospheric plasma spraying for carbon/carbon composites against long-term ablation

To protect carbon/carbon composites against long-term ablation, a bimodal microstructure ZrB₂-MoSi₂ coating, consisting of an outer ZrB₂-MoSi₂ layer modified by Y₂O₃ and an inner basal ZrB₂-MoSi₂ layer, was prepared by atmospheric plasma spraying. The microstructure, phase composition and ablation resistance of the proposed coating were investigated in detail. Results showed that the bimodal coating maintained integrity in structure except for phase composition. There was no visible interlayer between the inner ZrB₂-MiSi₂ layer and the outer modified one. Mass ablation rate of the bimodal microstructure ZrB₂-MoSi₂ coated C/C composites was −2.02 × 10⁻³ g/s under an oxyacetylene flame ablation at 1873 K for 600 s, which exhibited better ablation resistance than a single ZrB₂-MoSi₂ coating. The excellent ablation resistance was ascribed to the positive effect of Y₂O₃, which not only pined in the glassy phase and alleviated the volatilization of SiO₂ glass phase by reacting with SiO₂ to form high viscosity of Y₂SiO₅, but also stabilized ZrO₂ and promoted its recrystallization and growth.     

A mullite/SiC oxidation protective coating for carbon/carbon composites

To protect carbon/carbon (C/C) composites against oxidation, a mullite coating was prepared on SiC precoated C/C composites by a hydrothermal electrophoretic deposition process. The phase composition, microstructure and oxidation resistance of the prepared mullite/SiC coatings were investigated. Results show that hydrothermal electrophoretic deposition is an effective route to achieve crack-free mullite coatings. The mullite/SiC coating displays excellent oxidation resistance and can protect C/C composites from oxidation at 1773 K for 322 h with a weight loss rate of only 4.89 × 10^?4 g/cm² h. The failure of the multi-layer coatings is considered to be caused by the volatilization of silicate glass layer, the formation of microholes and microcracks on the coating surface and the formation of penetrative holes between the SiC bonding layer and the C/C matrix at 1773 K. The corresponding high temperature oxidation activation energy of the coated C/C composites at 1573–1773 K is calculated to be 111.11 kJ/mol.     

Preparation and high-temperature oxidation resistance of multilayer MoSi2/MoB coating by spent MoSi2-based materials

Spent MoSi₂ and MoB were used as raw materials to prepare multilayer MoSi₂/MoB coating on molybdenum by the two-step method of slurry deposition and spark plasma sintering. The results showed dense MoSi₂/MoB coating after sintering while penetrated cracks appeared in MoSi₂ coating due to coefficient of thermal expansion mismatch between the Mo substrate and coating. After the sintering of MoSi₂/MoB coatings, MoB and Mo₂B diffusion layers were formed between MoB transition layer and Mo substrate without defects, exhibiting good metallurgical bonding. The high-temperature oxidation behavior of coatings (1500°C) was also explored. After oxidation of 50 h at 1500°C, lowest mass gain (0.035 mg/cm²) was obtained for MoSi₂/MoB coating, and the oxide scale was dense and complete without voids, making the oxygen diffusion at elevated temperature inhibited. Compared with MoSi₂ coating under the same oxidation conditions, relatively thinner silica oxide scale was acquired by MoSi₂/MoB coating because of the reduction of cracks, and the multilayer coating exhibits better anti-oxidation properties at high temperature.     

Oxidation behavior of Al2O3 reinforced MoSi2 composite coatings fabricated by vacuum plasma spraying

MoSi₂, MoSi₂–10 vol.% Al₂O₃, MoSi₂–30 vol.% Al₂O₃ (denoted as MA0, MA1, MA3, respectively) coatings were fabricated by vacuum plasma spraying (VPS), and their oxidation behavior was examined at low temperature (500 °C) and high temperature (1500 °C). The test at 500 °C showed that the addition of Al₂O₃ effectively restrained the pest oxidation of MoSi₂. The MA1 coating had satisfactory fluid surface and presented good oxidation resistance at 1500 °C. However, the MA3 coating showed worse oxidation resistant behavior compared with the MA0 coating because of mullite formation.     

Mullite-Al2O3-SiC oxidation protective coating for carbon/carbon composites

In order to exploit the unique high temperature mechanical properties of carbon/carbon (C/C) composites, a new type of oxidation protective coating has been produced by a two-step pack cementation technique in an argon atmosphere. XRD analysis showed that the internal coating obtained from the first step was a gradient SiC layer that acts as a buffer layer, and the multi-layer coating formed in the second step was an Al₂O₃-mullite layer. It was found that the as-received coating characterized by excellent thermal shock resistance on the surface of C/C composites during exposure to an oxidizing atmosphere at 1873 K, could effectively protect the C/C composites from oxidation for 45 h. The failure of the coating is due to the formation of bubble holes on the coating surface.     

SiC/MoSi2 based coatings for Cf/C composites by two step pack cementation

In order to improve the oxidation resistance of C_f/Cs produced by chemical vapour infiltration, a multilayer coating based on silicon carbide and molybdenum disilicide was produced by two-step pack cementation technique. The inner SiC layer with a thickness up to 25 μm was obtained without promoted reaction additives by varying the composition, and thermal treatment conditions. The SiC/SiC-MoSi₂ coating was produced with a thickness up to 80 μm by two step pack cementation, considering the effect of the inner layer characteristic. The enhancement of the oxidation resistance, observed in SiC/SiC-MoSi₂ coated C_f/Cs by means of thermal analysis in flowing air up to 1500 °C, was due to the formation of SiO₂ promoted by the passive oxidation of silicon carbide and molybdenum disilicide.     

Thermal shock resistance of thermal barrier coatings for nickel-based superalloy by supersonic plasma spraying

Double-layer thermal barrier coatings (TBCs), including a top ZrO₂ layer and an inner CoNiCrAlY layer, were deposited on nickel-based superalloy using supersonic atmospheric plasma spraying (SAPS). Thermal shock resistance of the TBCs between 1200 °C and room temperature was investigated. After thermal shock test, the adhesive strength of the coatings was evaluated through scratch test. The SAPS–TBCs present good thermal shock resistance, exhibiting only 0.26% mass gain up to 150-time thermal cycling. Before thermal cyclic treatment, SAPS–TBCs exhibited a strong adhesion with the absence of the thermally grown oxide (TGO) between out and inner layer. With the increasing of thermal cycles, the TGO layer was formed and its thickness firstly increased and then dropped down. The critical load fell down by about 32% for topcoat–bondcoat adhesion (up to 50 cycles) and 35% or so for TBCs–substrate adhesion (up to 150 cycles) compared to the counterpart of as-sprayed specimens. The strain introduced by the existence of TGO and mixed oxides resulted in a varied adhesion for TBCs on nickel-based alloy during thermal cycling.     

Erosion protective coatings for low density, highly porous carbon/carbon composites

A simple and low cost method based on slurry coating was used to produce silicon carbide, titanium carbide and glass-ceramic coatings on low density carbon/carbon composites in order to improve their erosion resistance. Microstructural analyses were performed for substrate and coatings by optical microscopy, and scanning and transmission electron microscopy. As-received and coated composites were submitted to erosion tests using a sandblasting machine according to ASTM G76-95. The best results were obtained with a silica-alumina-yttria based glass-ceramic coating.     

SiCn/SiC oxidation protective coating for carbon/carbon composites

Nano-SiC (SiC_n) coating was deposited on SiC pre-coated C/C composites by a hydrothermal electrophoretic deposition. The phase compositions, surface and cross-section microstructures, and anti-oxidation properties of the multilayer coatings were investigated. Results show that hydrothermal electrophoretic deposition is an effective route to prepare smooth and homogeneous SiC_n coating on SiC-C/C composites. The as-prepared SiC_n/SiC multilayer coatings can effectively protect C/C composites from oxidation in air at 1773 K for 202 h with a weight loss of 0.79% and at 1873 K for 64 h with a weight loss of 1.3%.     

Characterization of composite titanium nitride coatings prepared by reactive plasma spraying

Reactive plasma spraying (RPS) technology has been used to produce high thickness (>100 μm) films of composite Ti-TiN-Ti_xN_y coatings. Reactively sprayed coatings obtained from SP700 (Ti-4.5Al-3V-2Mo-2Fe) and Ti6242 (Ti-6Al-2Sn-4Zr-2Mo) powders, deposited onto flat substrates of Ti-6Al-4V, have been investigated. X-ray diffraction (XRD) and micro-hardness measurements have been used to characterize the crystallographic features and differences between the hardness of cross-section and surface. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) techniques have been used to determine the morphology and surface chemical composition of the coatings. Back-scattered electron imaging has revealed the distribution of Ti and TiN in the composite material. Obtained results evidenced a sharp interface between the coating and substrate in terms of the profile of chemical composition. The presence of unmelted Ti particles as well as the formation of nitrides was observed.     

Effect of co-deposited SiC nanowires and carbon nanotubes on oxidation resistance for SiC-coated C/C composites

To protect carbon/carbon composites (C/Cs) against oxidation, SiC coating toughened by SiC nanowires (SiCNWs) and carbon nanotubes (CNTs) hybrid nano-reinforcements was prepared on C/Cs by a two-step technique involving electrophoretic co-deposition and reactive melt infiltration. Co-deposited SiCNWs and CNTs with different shapes including straight-line, fusiform, curved and bamboo dispersed uniformly on the surface of C/Cs forming three-dimensional networks, which efficiently refined the SiC grains and meanwhile suppressed the cracking deflection of the coating during the fabrication process. The presence of SiCNWs and CNTs contributed to the formation of continuous glass layer during oxidation, while toughed the coating by introducing toughing methods such as bridging effect, crack deflection and nanowire pull out. Results showed that after oxidation for 45 h at 1773 K, the weight loss percentage of SiC coated specimen was 1.35%, while the weight gain percentage of the SiCNWs/CNTs reinforced SiC coating was 0.03052% due to the formation of continuous glass layer. After being exposed for 100 h, the weight loss percentage of the SiCNWs/CNTs reinforced SiC coating was 1.08%, which is relatively low.     

High-temperature performances of Si-HfO2-based environmental barrier coatings via atmospheric plasma spraying

To improve high-temperature bearing capability of coatings, novel agglomerated Si-HfO₂ powders were prepared by adding HfO₂ powders into original Si powders by spray drying method. Three-layer environmental barrier coatings (EBCs) with Si-HfO₂ bond layer, Yb₂Si₂O₇ intermediate layer and Yb₂SiO₅ surface layer were prepared on SiC ceramic substrates by atmospheric plasma spraying (APS). The high temperature properties of coatings were systematically investigated. The results indicated that the coatings had good high temperature oxidation resistance, and remained intact after being oxidized or steam corrosion at 1400 °C for 500 h, so the addition of HfO₂ improved the thermal cycling performances of the coating. The HfO₂ in Si bond coating could effectively inhibit the growth of thermal grown oxide at high temperatures. This work indicates that the high temperature properties of the coatings are improved by this novel EBCs using the novel agglomerated Si-HfO₂ powders.     

Microstructure and properties of niobium carbide composite coatings prepared by plasma spraying

Niobium carbide composite coatings were prepared on titanium alloy surface by plasma spraying NbC–Al₂O₃, Nb–SiC and Nb–SiC–Al composite powders, respectively. The phase composition, microstructure and formation mechanism of the three composite coatings were analyzed and their microhardness, toughness and scratch resistance were compared. The phases of the NbC–Al₂O₃ system did not change during the plasma spraying process, and new phases (Nb₂C, NbC and Nb₃Si) were formed in the Nb–SiC and Nb–SiC–Al systems. TEM results of the Nb–SiC composite coating indicate that the new phases nanocrystalline Nb₂C, submicron NbC and nanocrystalline Nb₃Si were formed during the plasma spraying process. Compared with the NbC–Al₂O₃ composite coating, the microstructure of the Nb–SiC and the Nb–SiC–Al composite coatings were uniform, and the porosity were relatively low, and the hardness was higher. The Nb–SiC–Al composite coating was denser than the Nb–SiC composite coating, the lamellar structure was obvious and the number of pores in the coating was the least, which is attributed to the better molten state of the composite powder by the addition of the Al to the Nb–SiC system. The Nb–SiC–Al composite coating had better toughness and scratch resistance.