Microwave-assisted sintering of Al2O3-MWCNT nanocomposites

Alumina-MWCNT composite was densified by microwave sintering. CNTs were coated with boehmite nanoparticles to enhance their distribution in composite samples. Calcination temperature of composite powder was determined by TGA analysis (5 °C/min). Samples containing 0 and 1vol%CNT were produced by cold isostatic pressing at 180 MPa. Microwave sintering (1520 °C for 45 min) was conducted under the flow of argon. Phase analysis of the calcined composite powder showed complete transformation of boehmite into gamma-alumina. The relative densities were 99.3% and 98.1% for monolithic alumina and composite, respectively. CNT addition improved the fracture toughness of alumina by ~37%. SEM images showed that microwave sintering was successful. Also, coating CNTs improved their distribution in the alumina matrix.     

Carbon nanotube/boehmite-derived alumina ceramics obtained by hydrothermal synthesis and spark plasma sintering (SPS)

Preparation, structure and properties of hydrothermally treated carbon nanotube/boehmite (CNT/γ-AlOOH) and densification with spark plasma sintering of Al₂O₃ and CNT/Al₂O₃ nanocomposites were investigated. Hydrothermal synthesis was employed to produce CNT/boehmite from an aluminum acetate (Al(OH)(C₂H₃O₂)₂) and multiwall-CNTs mixture (200 °C/2 h.). TEM observations revealed that the size of the cubic shape boehmite particles lies around 40 nm and the presence of the interaction between surface functionalized CNTs and boehmite particles acts to form ‘nanocomposite particles’. Al₂O₃ and CNT/Al₂O₃ compact bodies were formed by means of spark plasma sintering (SPS) at 1600 °C for 5 min using an applied pressure of 50MPa resulting in the formation of stable α-Al₂O₃ phase and CNT–alumina compacts with nearly full density. It was also found that CNTs tend to locate along the alumina grain boundaries and therefore inhibit the grain coarsening and cause inter-granular fracture mode. The DC conductivity measurements reveal that the DC conductivity of CNT/Al₂O₃ is 10^?4 S/m which indicate that there is a 4 orders of magnitude increase in conductivity compared to monolithic Al₂O₃. The results of the microhardness tests indicate a slight increase in hardness for CNT/Al₂O₃ (28.35 GPa for Al₂O₃ and 28.57 GPa for CNT/Al₂O₃).     

Processing and properties of sol gel derived alumina–carbon nano tube composites

High purity alumina–carbon nano tube (CNT) composites were prepared by an aqueous sol–gel processing route. CNTs were dispersed in alumina sol containing appropriate amount of MgO precursor. Aqueous slurry of alumina was seeded into the sol followed by gelation, drying and calcination at 1000 °C for 1 h. The calcined powder consisting of alumina-coated CNTs and alumina was milled, sieved, dried, pressed and pressureless sintered at 1400–1600 °C for 1 h in nitrogen atmosphere. Sintered samples were further isostatically hot pressed at 1300 °C and the properties were compared with the pressureless sintered samples. Phase formation was followed by XRD study, CNT retention was confirmed by Raman studies and the samples were further characterized for mechanical and microstructural properties.     

Effect of particle size,heating rate and CNT addition on densification,microstructure and mechanical properties of B4C ceramics

Monolithic B₄C ceramics and B₄C–CNT composites were prepared by spark plasma sintering (SPS). The influence of particle size, heating rate, and CNT addition on sintering behavior, microstructure and mechanical properties were studied. Two different B₄C powders were used to examine the effect of particle size. The effect of heating rate on monolithic B₄C was investigated by applying three different heating rates (75, 150 and 225 °C/min). Moreover, in order to evaluate the effect of CNT addition, B₄C–CNT (0.5–3 mass%) composites were also produced. Fully dense monolithic B₄C ceramics were obtained by using heating rate of 75 °C/min. Vickers hardness value increased with increasing CNT content, and B₄C–CNT composite with 3 mass% CNTs had the highest hardness value of 32.8 GPa. Addition of CNTs and increase in heating rate had a positive effect on the fracture toughness and the highest fracture toughness value, 5.9 MPa m^1/2, was achieved in composite with 3 mass% CNTs.     

The growth of carbon nanotubes in aluminum powders by the catalytic pyrolysis of polyethylene glycol

A simple approach based on the catalytic pyrolysis of polyethylene glycol (PEG) was developed to grow a uniform dispersion of carbon nanotubes (CNTs) in Al powders and thus supply raw material for the powder metallurgy fabrication of CNT/Al composites. Al nanoflake powders with quite a large surface area were used to adsorb a homogeneous PEG and citric acid film, and then were impregnated with a cobalt nitrate solution to anchor Co(II) by complexation with citric acid. Then the Al nanoflake powders were heated to 230 °C to form Co oxide nanoparticles, and then to 570 °C to induce the thermal decomposition of PEG. The pyrolytic products of PEG not only served as the reducing agent to reduce Co oxide to Co nanoparticle catalyst, but also as the carbon source for CNT growth. As a result, 2.13 wt.% graphitic CNTs, with diameters of 10–20 nm and length ranging from sub-micron to a few micrometers, were homogeneously grown in 500 nm thick Al nanoflakes. And the as-obtained CNT/Al composites fabricated by hot-pressing exhibited enhanced strength, which was almost two times that of the matrix.     

Hot pressing of bimodal alumina powders with magnesium aluminosilicate (MAS) addition

High quality alumina ceramics were fabricated by hot-pressed sintering using bimodal alumina with superfine component as raw material and magnesium aluminosilicate (MAS) glass as sintering aid. Densification behavior, microstructure evolution and mechanical properties of alumina were investigated from 1300 °C to 1450 °C. The bimodal alumina powders were sintered to 99.8% of the theoretical value at 1400 °C and a comparative dense microstructure with a few plate-like abnormal grains was observed. With increase of sintering temperature up to 1450 °C, many fine matrix grains were consumed and quite a few abnormal grains impinged upon each other. For the alumina ceramics hot-pressed from bimodal alumina with 30 wt.% superfine component, optimal mechanical properties were obtained at 1400 °C. The bending strength and fracture toughness were 522 MPa and 5.0 MPa m^1/2, respectively.     

Fabrication of submicron alumina ceramics by pulse electric current sintering using M2+ (M = Mg,Ca, Ni)-doped alumina nanopowders

Dense submicron-grained alumina ceramics were fabricated by pulse electric current sintering (PECS) using M²⁺(M: Mg, Ca, Ni)-doped alumina nanopowders at 1250 °C under a uniaxial pressure of 80 MPa. The M²⁺-doped alumina nanopowders (0–0.10 mass%) were prepared through a new sol–gel route using high-purity polyhydroxoaluminum (PHA) and MCl₂ solutions as starting materials. The composite gels obtained were calcined at 900 °C and ground by planetary ball milling. The powders were re-calcined at 900 °C to increase the content of α-alumina particles, which act as seeding for low-temperature densification. Densification and microstructural development depend on the M²⁺ dopant species. Dense alumina ceramics (relative density ≥99.0%) thus obtained had a uniform microstructure composed of fine grains, where the average grain size developed for non-doped, Ni-doped, Mg-doped and Ca-doped samples was 0.67, 0.67, 0.47 and 0.30 μm, respectively, showing that Ca-doping is the most promising method for tailoring of nanocrystalline alumina ceramics.     

Microstructure and mechanical properties of Al2O3–20 wt%Al2TiO5 composite prepared from alumina and titania nanopowders

In the present work, Al₂O₃–20 wt%Al₂TiO₅ composite was prepared from reaction sintering of alumina and titania nanopowders. The nano-sized raw powders were reconstituted into nanostructured particles by ball milling. Then, the nanostructured reconstituted powders were pressed and pressureless-sintered into bulk ceramics at 1300, 1400, 1500 °C for 2 h. The phase composition and microstructures of reconstituted powders and as-prepared ceramic composites were characterized by using X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope and energy-dispersive spectrometer (EDS). The microstructural analysis of the ceramic showed that the average grain size of the alumina–aluminium titanate composite increases with increasing the temperature. Also, SEM proved the existence of a proper interface between Al₂TiO₅ and Al₂O₃ grains and preferential distribution of aluminium titanate particles in the grain boundaries. XRD analysis indicated the absence of rutile titania in the sintered composite ensuring complete formation of aluminium titanate. The hardness of the samples sintered at 1300, 1400, 1500 °C were 4.8, 6.2 and 8.5 GPa, respectively.     

Formation of multi-walled carbon nanotubes by Ni-catalyzed decomposition of methane at 600–750 °C

Ni-catalyzed decomposition of methane at high temperatures was examined by using a thermogravimetric apparatus. The catalyst (10 wt.% Ni supported on spherical alumina) gave quite a high carbon nanotube (CNT) yield at the temperatures below 680 °C. At > 700 °C, however, carbon formation rate decreased with increasing the reaction temperature. Temperature-programmed reaction also showed the maximum CNT growth rate at ~ 690 °C. This result ruled out the possibility that the apparent negative activation energy is caused by sintering of Ni particles. Detailed examination on the kinetic expression led us to a conclusion that the dissolution of carbon atoms formed by dissociation of methane into bulk of the nickel particles is the rate-determining step at high temperatures, while methane adsorption is the rate-determining step at lower temperatures. This idea also explains the fact that the carbon yield drastically decreased at high temperatures. The CNTs formed at these temperatures had thinner walls than those formed at lower temperatures. The latter fact also supports the idea that the solubility of carbon in the nickel particles decreases at high temperatures.     

Sol–gel derived alumina–hydroxyapatite–tricalcium phosphate porous composite powders

In this study, alumina–hydroxyapatite–tricalcium phosphate (α-Al₂O₃–HA–TCP) porous composite powders were produced and characterized. At first, boehmite sol (AlOOH) was obtained via sol–gel process by using aluminium isopropoxide (Al(OC₃H₇)₃) as the starting material. Bovine hydroxyapatite (BHA) powders derived from deproteinized bovine bones were added as 10, 20, 30 and 50% weight of the starting material to each boehmite sol. Also Na-alginate was added to the boehmite sol as the dispersive agent. Subsequently, gelation for 3 h at 110 °C was applied to each sol mixture. Finally, gelated samples were heat treated for 2 h at 500, 800, 1000 and 1300 °C. DTA–TGA, XRD, FTIR and SEM-EDS analyses were used to characterize the obtained composite powders composed of α-Al₂O₃–HA–TCP phases. In order to investigate porosity properties, powders were pressed with hydraulic manual press and formed into pellets. Later these pellets were sintered for 2 h at 1300 °C. Apparent porosity and bulk density tests were applied to the pellets. The evaluation of these tests results indicate that a novel α-Al₂O₃–HA–TCP composite material with ～38–44% apparent porosity has been produced.     

Preparation-microstructure-property relationships in double-walled carbon nanotubes/alumina composites

Double-walled carbon nanotube/alumina composite powders with low carbon contents (2–3 wt.%) are prepared using three different methods and densified by spark plasma sintering. The mechanical properties and electrical conductivity are investigated and correlated with the microstructure of the dense materials. Samples prepared by in situ synthesis of carbon nanotubes (CNTs) in impregnated submicronic alumina are highly homogeneous and present the higher electrical conductivity (2.2–3.5 S cm⁻¹) but carbon films at grain boundaries induce a poor cohesion of the materials. Composites prepared by mixing using moderate sonication of as-prepared double-walled CNTs and lyophilisation, with little damage to the CNTs, have a fracture strength higher (+30%) and a fracture toughness similar (5.6 vs 5.4   MPa m^1/2) to alumina with a similar submicronic grain size. This is correlated with crack-bridging by CNTs on a large scale, despite a lack of homogeneity of the CNT distribution.     

Pressureless sintering of carbon nanotube–Al2O3 composites

Alumina ceramics reinforced with 1, 3, or 5 vol.% multi-walled carbon nanotubes (CNTs) were densified by pressureless sintering. Commercial CNTs were purified by acid treatment and then dispersed in water at pH 12. The dispersed CNTs were mixed with Al₂O₃ powder, which was also dispersed in water at pH 12. The mixture was freeze dried to prevent segregation by differential sedimentation during solvent evaporation. Cylindrical pellets were formed by uniaxial pressing and then densified by heating in flowing argon. The resulting pellets had relative densities as high as ～99% after sintering at 1500 °C for 2 h. Higher temperatures or longer times resulted in lower densities and weight loss due to degradation of the CNTs by reaction with the Al₂O₃. A CNT/Al₂O₃ composite containing 1 vol.% CNT had a higher flexure strength (～540 MPa) than pure Al₂O₃ densified under similar conditions (～400 MPa). Improved fracture toughness of CNT–Al₂O₃ composites was attributed to CNT pullout. This study has shown, for the first time, that CNT/Al₂O₃ composites can be densified by pressureless sintering without damage to the CNTs.     

Investigation of the structural and mechanical properties of micro-/nano-sized Al2O3 and cBN composites prepared by spark plasma sintering

Alumina-cubic boron nitride (cBN) composites were prepared using the spark plasma sintering (SPS) technique. Alpha-alumina powders with particle sizes of ∼15 µm and ∼150 nm were used as the matrix while cBN particles with and without nickel coating were used as reinforcement agents. The amount of both coated and uncoated cBN reinforcements for each type of matrix was varied between 10 to 30 wt%. The powder materials were sintered at a temperature of 1400 °C under a constant uniaxial pressure of 50 MPa. We studied the effect of the size of the starting alumina powder particles, as well as the effect of the nickel coating, on the phase transformation from cBN to hBN (hexagonal boron nitride) and on the thermo-mechanical properties of the composites. In contrast to micro-sized alumina, utilization of nano-sized alumina as the starting powder was observed to have played a pivotal role in preventing the cBN-to-hBN transformation. The composites prepared using nano-sized alumina reinforced with nickel-coated 30 wt% cBN showed the highest relative density of 99% along with the highest Vickers hardness (H_v2) value of 29 GPa. Because the compositions made with micro-sized alumina underwent the phase transformation from cBN to hBN, their relative densification as well as hardness values were relatively low (20.9–22.8 GPa). However, the nickel coating on the cBN reinforcement particles hindered the cBN-to-hBN transformation in the micro-sized alumina matrix, resulting in improved hardness values of up to 24.64 GPa.     

Improving the surface hardness of zirconia toughened alumina (ZTA) composites by surface treatment with a boehmite sol

This paper reports a novel way of enhancing the hardness of a zirconia-toughened alumina (ZTA) composite with a zirconia content of 20 vol% by surface treatments with a boehmite sol. More specifically, a ZTA composite was first prepared by heat-treating a mixture of alumina and zirconia powders containing Cr₂O₃ and SrAl₁₁CrO₁₉, as a reinforcement at 1400 °C for 1 h, and then infiltrating them with the boehmite sol, followed by heat-treatment at 1650 °C for 1 h to densify them. This treatment led to a significant increase in the surface hardness of the ZTA composite, which was attributed mainly to an increase in the volume fraction of an alumina phase with greater hardness, whereas the flexural strength and fracture toughness decreased slightly. The Vickers hardness, flexural strength and fracture toughness were 17.1 ± 2.5 GPa, 738 ± 88 MPa and 4.2 ± 0.11 MPa m^1/2, respectively.     

CVD growth and field electron emission of aligned carbon nanotubes on oxidized Inconel plates without addition of catalyst

Direct growth of carbon nanotubes (CNTs) on Inconel 600 sheets was investigated using plasma enhanced hot filament chemical vapor deposition in a gas mixture of methane and hydrogen. The Inconel 600 sheets were oxidized at different temperatures (800 °C, 900 °C, 1000 °C, and 1100 °C) before CNT deposition. The structure and surface morphology of the pre-treated substrate sheets and the deposited CNTs were studied by scanning electron microscopy (SEM) and X-ray diffraction. The field electron emission (FEE) properties of the CNTs were also tested. The SEM results show that well aligned CNTs have been grown on the pre-treated Inconel sheets without addition of any catalysts and the higher treatment temperature resulted in CNTs with better uniformity, indicating that the oxidation pre-treatment of the substrate is effective to enhance the CNT growth. FEE testing shows that CNTs with better height uniformity exhibit better FEE characteristics.     

Synthesis and characterization of boehmitic alumina coated graphite by sol–gel method

Non-wettability property makes graphite a good protecting material against the molten metal and/or slag. Properties like high oxidation potential between 600 and 1200 °C and non-wettability with water at room temperatures limits the usage of graphite in castable refractory applications. In this study, sol–gel method, which is a relatively cheaper process, was used. Boehmitic sol was obtained by hydrolyzing and peptiziting the alkoxide AIP (aluminum isopropoxide) used as alumina source. Then natural flake graphite was mixed with the boehmitic solution for coating of graphite. At 120 °C boehmitic sol coated graphite was dried and gelled. Then heat threaded at 550 °C for γ-Al₂O₃ transformation of boehmite. Products that obtained from the studies were characterized with FTIR and XRD tests. Alumina coated graphite samples were made by repeating the same steps and TG analysis were made to investigate the oxidation behaviour of the samples. Finally, SEM–EDS analyses were carried out to investigate the microscopic properties of the alumina coated graphite powders.     

Synthesis and characterisation of silica–carbon nanotube hybrid microparticles and their effect on the electrical properties of poly(vinyl alcohol) composites

Hybrid silica–carbon nanotube (CNT) particles with a radial symmetry were produced by the growth of nanotubes onto spherical, mesoporous silica gel particles using the floating catalyst chemical vapour deposition (FC-CVD) method. Characterisation of the hybrid particles, using electron microscopy, Raman spectroscopy and thermogravimetry showed the geometry and porosity of the silica particles to influence the alignment and density of the CNTs produced. CNT growth initiated in the pores of the gel particles and three hours of CVD growth were required to get extensive surface coverage. In the early stages of growth, the reactants diffused inside the mesoporous silica and consequently the CNTs grew mainly within the silica gel rather than on the surface. Some indication of catalyst templating was observed within the smaller (<10 nm) pores, but this templating did not result in aligned CNTs. Composite films of hybrid silica–CNT particles in poly(vinyl alcohol) were cast and their impedance measured. An electrical percolation threshold of 0.62 wt.% was found for the hybrid particles, of which 0.20 wt.% were CNTs.     

Low temperature growth mechanisms of vertically aligned carbon nanofibers and nanotubes by radio frequency-plasma enhanced chemical vapor deposition

Using radio frequency-plasma enhanced chemical vapor deposition (RF-PECVD), carbon nanofibers (CNFs) and carbon nanotubes (CNTs) were synthesized at low temperature. Base growth vertical turbostratic CNFs were grown using a sputtered 8 nm Ni thin film catalyst on Si substrates at 140 °C. Tip growth vertical platelet nanofibers were grown using a Ni nanocatalyst in 8 nm Ni films on TiN/Si at 180 °C. Using a Ni catalyst on glass substrate at 180 °C a transformation of the structure from CNFs to CNTs was observed. By adding hydrogen, tip growth vertical multi-walled carbon nanotubes were produced at 180 °C using FeNi nanocatalyst in 8 nm FeNi films on glass substrates. Compared to the most widely used thermal CVD method, in which the synthesis temperature was 400–850 °C, RF-PECVD had a huge advantage in low temperature growth and control of other deposition parameters. Despite significant progress in CNT synthesis by PECVD, the low temperature growth mechanisms are not clearly understood. Here, low temperature growth mechanisms of CNFs and CNTs in RF-PECVD are discussed based on plasma physics and chemistry, catalyst, substrate characteristics, temperature, and type of gas.     

The microstructure,coefficient of thermal expansion and flexural strength of cordierite ceramics prepared from alumina with different particle sizes

Cordierite ceramics were produced from alumina with 5 and 0.65 μm particle sizes or AlOOH and talc, clays and feldspar, to determine the influence of the alumina particle size on the microstructure, coefficient of thermal expansion (CTE) and flexural strength (FS) of the ceramics. After sintering at 1300 °C the ceramics made from 5-μm-sized alumina consisted of cordierite, glass, quartz, mullite and alumina, and had the highest density, FS and CTE. The alumina grains act as inclusions, from which the trajectories of the cracks were deflected or terminated, which increases the FS and CTE. The ceramics from sub-micrometre-sized alumina or AlOOH contained a negligable amount and no alumina, respectively, together with other phases. This is reflected in the low CTE and FS. The cordierite ceramic with the lowest CTE of ∼2.0 × 10⁻⁶ K⁻¹ and a high FS of 100 MPa was prepared from the 0.65-μm-sized alumina particles.     

Highly transparent AlON ceramics sintered from powder synthesized by carbothermal reduction nitridation

Aluminum oxynitride (AlON) powders were synthesized by the carbothermal reduction and nitridation process using commercial γ-Al₂O₃ and carbon black powders as starting materials. And AlON transparent ceramics were fabricated by pressureless sintering under nitrogen atmosphere. The effects of ball milling time on morphology and particle size distribution of the AlON powders, as well as the microstructure and optical property of AlON transparent ceramics were investigated. It is found that single-phase AlON powder was obtained by calcining the γ-Al₂O₃/C mixture at 1550 °C for 1 h and a following heat treatment at 1750 °C for 2 h. The AlON powder ball milled for 24 h showed smaller particles and narrower particle size distribution compared with the 12 h one, which was benefit for the improvement of optical property of AlON transparent ceramics. With the sintering aids of 0.25 wt% MgO and 0.04 wt% Y₂O₃, highly transparent AlON ceramics with in-line transmittance above 80% from visible to infrared range were obtained through pressureless sintering at 1850 °C for 6 h.