Microstructure and properties of porous SiC ceramics by LPCVI technique regulation

A new gradient pore structure in porous SiC ceramics was fabricated by low pressure chemical vapor infiltration (LPCVI). Effects of deposition duration on the mechanical properties and permeability of porous SiC ceramics were investigated. Results demonstrated that pore diameter and shapes decreased from the surface to the interior along with LPCVI duration. Porous SiC ceramics with deposition duration of 160 h exhibited flexural strength of 48.05 MPa and fracture toughness of 1.30 MPa m^1/2, where 221% and 189% improvements were obtained compared to porous SiC ceramics without LPCVI, due to CVI-SiC layer strengthening effect. Additionally, at the same gas velocity, pressure drop increase rate was faster due to apparent porosity and pore size change.     

An advanced method to manufacture hierarchically structured carbide-derived carbon monoliths

The preparation of carbide-derived carbon (CDC) monoliths with a hierarchically structure in the nm and μm range is presented. Basis is the manufacturing of porous cellular SiC ceramics based on a biomorphous approach with μm porosity and subsequent conformal conversion to CDC by reactive extraction with chlorine. The SiC ceramics can be sintered at low temperatures and short times (1500 °C, 2 h) compared to classical preparation methods. The SiC ceramics show a macro pore volume (1–10 μm channel size) of 0.56 ml g⁻¹, which corresponds to 1.5 ml g⁻¹ in the resulting CDC. The final carbon material exhibits an additional nano pore volume of 0.525 ml g⁻¹ with a mean slit pore size of 0.86 nm. Mechanical stabilities of the highly porous CDC are excellent (bending strength 2.1 ± 0.2 MPa, corrected Weibull modulus 8.7, characteristic strength 2.2 MPa and Youngs modulus 10.0 ± 0.5 GPa). The reactive extraction of the carbide monoliths shows very high reaction rates, approx. two dimensions faster (95×) compared to non-porous samples. Thus the manufacturing of the structured carbide and CDC can be performed at lower costs.     

Preparation and characterization of lotus ceramics with different pore sizes and their implication for the generation of microbubbles for CO2 sequestration applications

Four kinds of porous mullite ceramics, named lotus ceramics because of the similarity of their microstructure with lotus roots, were prepared by an extrusion method using rayon fibers of four different diameters (8.1, 9.6, 16.8 and 37.6 μm) as the pore formers. The physicochemical properties of these samples were characterized to test their applicability for the generation of microbubbles. The lotus ceramic samples contained pores of 9.4, 10, 15.6 and 30 μm size and porosities of 45–48%. SEM micrographs confirmed that the cylindrical pores were oriented unidirectionally along the extrusion direction and the degree of alignment was greater with larger fiber diameter. The permeability for gaseous CO₂ increased with increasing pore size from 3×10^?13 to 8×10^?13 m². The four lotus ceramic samples, a commercial air stone (72 μm) and two simple tubes (1000 and 3500 μm) were used to generate microbubbles in water under ambient conditions from a gas mixture of CO₂ and air. It was found that the bubble size could be decreased with bubblers of smaller pore size. In the bubble size measurements for pure CO₂ and air, the air bubbles were larger than the CO₂ bubbles due to partial dissolution of CO₂ into the water during bubbling. In order to generate smaller size bubbles using porous ceramic bubblers, the liquid must penetrate through the pores of the lotus ceramics before the gas is introduced into the system.     

Processing and properties of cordierite-silica bonded porous SiC ceramics

Cordierite-silica bonded porous SiC ceramics were fabricated by infiltrating a porous powder compact of SiC with cordierite sol followed by sintering at 1300–1400 °C in air. The porosity, average pore diameter and flexural strength of the ceramics varied 30–36 vol%, ~ 4–22 µm and ~ 13–38 MPa respectively with variation of sintering temperature and SiC particle sizes. In the final ceramics SiC particles were bonded by the oxidation-derived SiO₂ and sol-gel derived cordierite. The corrosion behaviour of sintered SiC ceramics was studied in acidic and alkaline medium. The porous SiC ceramics were observed to exhibit better corrosion resistance in acid solution.     

Effects of CeO2 addition on the properties of cordierite-bonded porous SiC ceramics

Cordierite-bonded porous SiC ceramics were fabricated with and without CeO₂ addition in air by an in situ reaction bonding technique. The effects of CeO₂ addition on the phase composition, microstructure and properties of porous SiC ceramics were investigated. It was found that the CeO₂ addition strongly promotes the phase transformation towards cordierite while inhibits the formation of spinel. With CeO₂ addition, the neck growth was enhanced, and the mechanical properties of porous SiC ceramics were improved. When 2.0 wt.% CeO₂ was added, a flexural strength of 35.3 MPa was achieved at an open porosity of 42.1%. Pore size distribution characterization by mercury porosimetry indicated that 2.0 wt.% CeO₂ addition enlarged the average pore size of porous SiC ceramics and introduced a bigger homogeneity in pore size. In addition, it was found that higher permeability was obtained after adding 2.0 wt.% CeO₂. Moreover, the thermal shock resistance of cordierite-bonded porous SiC ceramics was also improved by the addition of CeO₂.     

Microstructure and mechanical properties of ZrB2–SiC porous ceramic by camphene-based freeze casting

Camphene-based freeze casting technique was adopted to fabricate ZrB₂–SiC porous ceramic with 3-dimensional (3D) pore network. ZrB₂–SiC/camphene slurries (initial solid loading: 20 vol%, 25 vol% and 30 vol%) were prepared for freeze casting. Regardless of initial solid loading, the fabricated sample had dense/porous dual microstructure. The thickness of dense layer was about 200–300 μm. The microstructures of ZrB₂–SiC porous ceramics were significantly influenced by the initial solid loading, which determines the pore size, porosity and mechanical properties of the final products.     

Characteristics of microbubbles generated by porous mullite ceramics prepared by an extrusion method using organic fibers as the pore former

Porous mullite ceramics with unidirectionally oriented pores were prepared by an extrusion method using rayon fibers as the pore formers and the characteristics of microbubbles generated by these porous ceramics were investigated. The 1200 mm long ceramics were tubular and of thick or thin types of 20–30 mm inner diameter and 30–50 mm outer diameter, respectively. The thin and thick samples had porosities of 47 and 49% and average pore radii of 7.8 μm. The gas permeabilities of the thick and thin samples were 4.1 × 10^?14 and 5.4 × 10^?14 m², respectively. Microbubbles were generated by introducing N₂ gas through the ceramic tube by immersing it into water. The minimum pressure (bubble point pressure) for generation of microbubbles was 20 kPa, much lower than for other bubble-forming methods. The average microbubble radii ranged from about 70 to 105 μm at flow rates of 0.15–0.25 L/min in the thin sample and 0.3–0.7 L/min in the thick sample. These bubble sizes are much smaller than calculated for a Fritz-type bubble such as generally formed by bubbling from pores and/or orifices. However, the present bubble sizes agree well with the calculated value based on nanobubbles, indicating that bubble formation occurs by mixing the gas with water in small pores. Since microbubbles enhance the dissolution rate of a gas phase in water, they are potentially useful for improving water environments, especially oxygen-deficient water. The effectiveness of gas dissolution in water was confirmed by determining the dissolution behavior of CO₂ gas using these porous ceramics.     

Fabrication and properties of ultra highly porous silicon carbide by the gelation–freezing method

Silicon carbide (SiC) with ultra high porosity and unidirectionally oriented micrometer-sized cylindrical pores was prepared using a novel gelation–freezing (GF) method. Gelatin, water and silicon carbide powder were mixed and cooled at 7 °C. The obtained gels were frozen from ?10 to ?70 °C, dried using a vacuum freeze drier, degreased at 600 °C and then sintered at 1800 °C for 2 h. The gels could be easily formed into various shapes, such as cylinders, large pipes and honeycombs using molds. Scanning electron microscopy (SEM) observations of the sintered bodies showed a microstructure composed of ordered micrometer-sized cylindrical cells with unidirectional orientation. The cell size ranging from 34 to 147 μm could be modulated by changing the freezing temperatures. The numbers of cells for the samples frozen at ?10 and ?70 °C were 47 and 900 cells/mm², respectively, as determined from cross-sections of the sintered bodies. The resulting porous SiC with a total porosity of 86%, exhibited air permeability from 2.3 × 10^?11 to 1.0 × 10^?10 m², which was the same as the calculated ideal permeability, and high compressive strength of 16.6 MPa. The porosity, number of cells, air permeability and strength of the present porous SiC were significantly higher than that reported for other porous SiC ceramics.     

Fabrication and characterization of cordierite-bonded porous SiC ceramics

A reaction bonding technique was used for the preparation of cordierite-bonded porous SiC ceramics in air from α-SiC, α-Al₂O₃ and MgO, using graphite as the pore-forming agent. Graphite was burned out to produce pores and the surface of SiC was oxidized to SiO₂ at high temperature. With further increasing the temperature, SiO₂ reacted with α-Al₂O₃ and MgO to form cordierite. SiC particles were bonded by the cordierite and oxidation-derived SiO₂. The reaction bonding characteristics, phase composition, open porosity, pore size distribution and mechanical strength as well as microstructure of porous SiC ceramics were investigated. The pore size and porosity were strongly dependent, respectively, on graphite particle size and volume fraction. The porous SiC ceramics sintered at 1350 °C for 2 h exhibited excellent combination properties, the flexural strength of 26.0 MPa was achieved at an open porosity of 44.51%.     

Graphite and PMMA as pore formers for thermoplastic extrusion of porous 3Y-TZP oxygen transport membrane supports

A gas permeable porous support is a crucial part of an asymmetric oxygen transport membrane (OTM). Here, we develop feedstocks for thermoplastic extrusion of tubular, porous 3Y-TZP (partially stabilized zirconia polycrystals, (Y₂O₃)_0.03(ZrO₂)_0.97)) ceramics, using graphite and/or polymethyl methacrylate (PMMA) as pore formers. The influence of pore former content and type, 3Y-TZP particle size and support sintering temperature on the microstructure, porosity and gas permeability were studied. Using at least 40 vol% pore former, consisting of graphite and PMMA in the volume ratio 2:1, tubes with gas permeability exceeding the target of 10⁻¹⁴ m² are obtained. In the temperature range 1250–1400 °C the support gas permeability is insensitive to the sintering temperature, and the feedstocks shrink more than 15% during sintering, making them ideal for co-sintering with functional OTM layers. This demonstrates the suitability of thermoplastic extrusion for fabrication of porous 3Y-TZP OTM supports, or for other technologies requiring porous ceramics.     

Electrical resistivity of α-SiC ceramics sintered with Al2O3 or AlN additives

Highly resistive SiC ceramics were prepared by hot pressing α-SiC powders with Al₂O₃-Y₂O₃ additives with a 4:1 molar ratio. X-ray diffraction patterns, Raman spectra, electron probe microanalysis (EMPA), and scanning electron microscopy (SEM) images revealed that the bulk SiC ceramics consisted mostly of micron-sized 6H-SiC grains along with Y₂O₃ and Si clusters. As the additive content increased from 1 to 10 vol%, the electrical resistivity of the ceramics increased from 3.0 × 10⁶ to 1.3 × 10⁸ Ω cm at room temperature. Such high resistivity is ascribed to Al₂O₃ in which Al impurities substituting Si site act as deep acceptors for trapping carriers. More resistive α-SiC ceramics were produced by adding AlN instead of Al₂O₃. The highest resistivity (1.3 × 10¹⁰ Ω cm) was achieved by employing 3 vol% AlN-Y₃Al₅O₁₂ (yttrium aluminum garnet, YAG) as an additive.     

Preparation and characterization of porous,biomorphic SiC ceramic with hybrid pore structure

Bio-carbon template (charcoal) was prepared by carbonizing pine wood at 1200 °C under vacuum, and was impregnated with phenolic resin/SiO₂ sol mixture by vacuum/pressure processing. Porous SiC ceramics with hybrid pore structure, a combination of tubular pores and network SiC struts in the tubular pores, were fabricated via sol–gel conversion, carbonization and carbothermal reduction reaction at elevated temperatures in Ar atmosphere. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM) were employed to characterize the phase identification and microstructural changes during the C/SiO₂ composites-to-porous SiC ceramic conversion. Experimental results show that the density of C/SiO₂ composite increases with the number of impregnation procedure, and increases from 0.32 g cm⁻³ of pine-derived charcoal to 1.5 g cm⁻³ of C/SiO₂ composite after the sixth impregnation. The conversion degree of charcoal to porous SiC ceramic increases as reaction time is lengthened. The resulting SiC ceramic consists of β-SiC with a small amount of α-SiC. The conversion from pine charcoal to porous SiC ceramic with hybrid pore structure improves bending strength from 16.4 to 42.2 MPa, and decreases porosity from 76.1% to 48.3%.     

Porous SiC/SiCN composite ceramics fabricated by foaming and reaction sintering

Porous SiC/SiCN composite ceramics with heterogeneous pore structure and rod-like SiCN grains were fabricated by foaming and reaction sintering. The mixture slurry containing SiC and silicon as raw materials, cornstarch as binder, Y₂O₃ as sintering additive and an electrosteric dispersant was stirred with foams derived from pre-foaming using foaming agent. The casted green body was sintered at 1650 °C under nitrogen atmosphere. The results demonstrated that the porous SiC/SiCN ceramics exhibited hierarchical vias ranging from 1 μm to 1 mm and the rod-like crystalline SiCN grains generated in the SiC matrix.     

Fabrication and electrochemical properties of SOFC single cells using porous yttria-stabilized zirconia ceramic support layer coated with Ni

A porous yttria-stabilized zirconia (YSZ) ceramic supported single cell with a configuration of porous YSZ support layer coated with Ni/Ni–Ce_0.8Sm_0.2O_1.9 (SDC) anode/YSZ/SDC bi-layer electrolyte/La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ cathode was fabricated. The porosity, mechanical strength, and microstructure of porous YSZ ceramics were investigated with respect to the amount of poly(methyl methacrylate) (PMMA) used as a pore former. Porous YSZ ceramics with 56 vol.% PMMA showed a mechanical strength of 24 ± 3 MPa and a porosity of 37 ± 1%. The electrochemical properties of the single cell employing the porous YSZ support layer were measured using hydrogen and methane fuels, respectively. The single cell exhibited maximum power densities of 421 mW/cm² in hydrogen and 399 mW/cm² in methane at 800 °C. Moreover, at a current density of 550 mA/cm², the cell maintained 91% of its initial voltage after operation in methane for 13 h at 700 °C.     

Synthesis of hierarchical porous silicon oxycarbide ceramics from preceramic polymer and wood biomass composites

Hierarchical porous SiOC ceramics were successfully prepared using a polysiloxane preceramic polymer mixed with wood biomass by annealing at different temperatures under Ar atmosphere. These SiOC ceramics display a trimodal pore size distribution in the micro-, meso- (micropores + mesopores, 1.7–14 nm) and macro-size scale (1–15 μm). The mesopores and micropores mainly originate from the formation of large amounts of SiC crystals and nanowires, graphite-like microcrystallites, and nm-scale pores of ray parenchyma cells and pits of the wood biomass. The SiOC sample prepared at a higher temperature processes the specific surface area up to 180.5 m²/g. The specific surface area, pore volume and average pore width of the samples can be controlled by adjusting the pyrolysis temperature.     

Effect of recoating slurry compositions on the microstructure and properties of SiC reticulated porous ceramics

Silicon carbide reticulated porous ceramics (SiC RPCs) were fabricated by polymer sponge replica technique, followed by recoating with SiC slurries of two different sintering additives of MgO–Al₂O₃–SiO₂ (Slurry 1) and polycarbosilane (Slurry 2). The sintering temperature of SiC RPCs recoated with Slurry 2 was 1100 °C, which was 200 °C lower than that for one recoated with Slurry 1. The prepared SiC RPCs exhibited homogeneous microstructure and contained pores with different sizes which was entrapped in the strut of SiC RPCs, small pores with diameter lower than 4 μm and large pores with diameter higher than 10 μm. Bending strength of SiC RPCs recoated with Slurry 1 was two times higher than that for the non-recoated samples, which was 1.88 MPa and was a little higher than that for one recoated with slurry 2. At the same time, high thermal shock resistance and high refractoriness were achieved for SiC RPCs recoated with Slurry 2.     

Effect of glassy bonding materials on the properties of LAS/SiC porous ceramics with near zero thermal expansion

Near zero thermal expansion porous ceramics were fabricated by using SiC and LiAlSiO₄ as positive and negative thermal expansion materials, respectively, bonded by glassy material. The coefficient of thermal expansion value of a desired porous composite can be easily controlled by choosing the appropriate ratios of the different phases. It was shown that some of LiAlSiO₄ was decomposed to LiAlSi₂O₆ and LiAlO₂, some of LiAlSiO₄ reacted with SiO₂ to form LiAlSi₂O₆ during sintering. With increasing the content of glassy materials, the reaction between LiAlSiO₄ and SiO₂ was accelerated. The Young's modulus increased due to the neck growth between the SiC grains. The 52.5 vol% LiAlSiO₄ (LAS)/SiC ceramics with ∼36% porosity had a combination of near zero coefficient of thermal expansion ∼0.39 × 10⁻⁶ K⁻¹ at room temperature and relatively high Young's modulus ∼59 GPa.     

The decrease of depolarization temperature and the improvement of pyroelectric properties by doping Ta in lead-free 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 ceramics

Ta-doped lead-free 0.94NBT-0.06BT-xTa (x=0.0–1.0%) ceramics were synthesized by a conventional solid-state route. XRD shows that the compositions are at a morphotropic phase boundary where rhombohedral and tetragonal phases coexist. The depolarization temperature (T_d) shifted to lower temperature with the increase of Ta content. The pyroelectric coefficient (p) of doped ceramics greatly enhanced compared with undoped material and reached a maximum of 7.14×10⁻⁴ C m⁻² °C⁻¹ at room temperature (RT) and 146.1×10⁻⁴ C m⁻² °C⁻¹ at T_d at x=0.2%. The figure of merits, F_i and F_v, also showed a great improvement from 1.12×10⁻¹⁰ m v⁻¹ and 0.021 m² C⁻¹ at x=0.0 to 2.55×10⁻¹⁰ m v⁻¹ and 0.033 m² C⁻¹ at x=0.2% at RT. Furthermore, F_i and F_v show the huge improvement to 52.2×10⁻¹⁰ m v⁻¹ and 0.48×10⁻¹⁰ m v⁻¹ respectively at T_d at x=0.2%. F_C shows a value between 2.26 and 2.42 ×10⁻⁹ C cm⁻² °C⁻¹ at RT at x=0.2%. The improved pyroelectric properties make NBT-0.06BT-0.002Ta ceramics a promising infrared detector material.     

Permeability and corrosion resistance of porous SiOC-bonded SiC ceramics prepared by the preceramic polymer

Porous SiC ceramics have been used in high temperature flue gas filtration fields because of their excellent properties such as high strength, high temperature resistance, corrosion resistance, and long service time. This work reports the porous SiOC-bonded SiC ceramics prepared at low temperature. The properties of porous SiC ceramics were first investigated with silicone resin content from 10 to 25 wt%, and then the effects of different pore-forming agent contents on the behaviors of porous SiC ceramics were discussed by adjusting poly (methyl methacrylate) PMMA microbeads from 5 to 20 wt%. The prepared porous SiC ceramics showed apparent porosity from 17.3% to 57.7%, compressive strength from 6 to 216 MPa, and Darcy permeability k₁ ranging from 7.02 × 10⁻¹⁴ to 1.45 × 10⁻¹² m². The corrosion behavior of porous SiC ceramics was investigated in acidic and alkaline media. The porous SiC ceramics showed better corrosion resistance in acidic solutions.     

Preparation and properties of mullite-bonded porous fibrous mullite ceramics by an epoxy resin gel-casting process

Porous fibrous mullite ceramics with a narrow range of pore size distribution have been successfully prepared utilizing a near net-shape epoxy resin gel-casting process by using mullite fibers, Al₂O₃ and SiC as raw materials. The effects of sintering temperatures, different amounts of fibers and Y₂O₃ additive on the phase compositions, linear shrinkage, apparent porosity, bulk density, microstructure, compressive strength and thermal conductivity were investigated. The results indicated that mullite-bonded among fibers were formed in the porous fibrous mullite ceramics with a bird nest pore structure. After determining the sintering temperatures and the amount of fibers, the tailored porous fibrous mullite ceramics had a low linear shrinkage (1.36–3.08%), a high apparent porosity (61.1–71.7%), a relatively high compressive strength (4.4–7.6 MPa), a low thermal conductivity (0.378–0.467 W/m K) and a narrow range of pore size distribution (around 5 µm). The excellent properties will enable the porous ceramics as a promising candidate for the applications of hot gas filters, thermal insulation materials at high temperatures.