Doping effect on sinterability of polycrystalline yttria: From the viewpoint of cation diffusivity

The sintering behavior of Y₂O₃ doped with 1 mol% of a trivalent or tetravalent cation was investigated by pressureless sintering in air. Ga³⁺ or Ge⁴⁺-doped Y₂O₃ bodies exhibited higher relative densities than the undoped Y₂O₃, while the La³⁺ or Zr⁴⁺-doping suppressed the densification of Y₂O₃. An interdiffusion experiment was performed on the diffusion couples of polycrystalline Er₂O₃ and Y₂O₃ doped with Ni²⁺ or Zr⁴⁺, which are some of the most effective and least effective dopants for the improvement of the sinterability, respectively. The lattice and grain boundary diffusion coefficients of the Er³⁺ cation in Y₂O₃ were increased by the Ni²⁺-doping, but were decreased by the Zr⁴⁺-doping. High-resolution transmission electron microscopy observations and nano-probe X-ray energy dispersive spectroscopy analyses confirmed that the dopant cations segregate along the grain boundaries without forming an amorphous phase. The doping effect on the sinterability of Y₂O₃ must result from the change in the diffusivity in Y₂O₃.     

Densification of nanocrystalline Y2O3 ceramic powder by spark plasma sintering

Nanocrystalline Y₂O₃ powders with 18 nm crystallite size were sintered using spark plasma sintering (SPS) at different conditions between 1100 and 1600 °C. Dense specimens were fabricated at 100 MPa and 1400 °C for 5 min duration. A maximum in density was observed at 1400 °C. The grain size continuously increased with the SPS temperature into the micrometer size range. The maximum in density arises from competition between densification and grain growth. Retarded densification above 1400 °C is associated with enhanced grain growth that resulted in residual pores within the grains. Analysis of the grain growth kinetics resulted in activation energy of 150 kJ mol^?1 and associated diffusion coefficients higher by 10³ than expected for Y³⁺ grain boundary diffusion. The enhanced diffusion may be explained by combined surface diffusion and particle coarsening during the heating up with grain boundary diffusion at the SPS temperature.     

Phase-transformation and grain-growth kinetics in yttria-stabilized tetragonal zirconia polycrystal doped with a small amount of alumina

Microstructure development during sintering in 3 mol% Y₂O₃-stabilized tetragonal zirconia polycrystal doped with a small amount of Al₂O₃ was investigated in the isothermal sintering conditions of 1300–1500 °C. At the low sintering temperature at 1300 °C, although the density was relatively high, the grain-growth rate was much slow. In the specimen sintered at 1300 °C for 50 h, Y³⁺ and Al³⁺ ions segregated along grain boundaries within the widths of about 10 and 6 nm, respectively. In grain interiors, the cubic-phase regions were formed by not only a grain-boundary segregation-induced phase-transformation mechanism but also by spinodal decomposition. The grain-growth behavior was kinetically analyzed using the grain-size data in 1300–1500 °C, which indicated that the grain-growth rate was enhanced by Al₂O₃-doping. These phase-transformation and grain-growth behaviors are reasonably explained by the diffusion-enhanced effect of Al₂O₃-doping.     

Sintering of Yb3+:Y2O3 transparent ceramics in hydrogen atmosphere

Highly transparent Yb³⁺:Y₂O₃ ceramics with doping concentration up to 40.0 at.% had been fabricated successfully via hydrogen atmosphere sintering, where the raw powders were synthesized by co-precipitation method. The sintering temperature is about 600 °C lower than its melting temperature. SEM investigation revealed the average grain size of Yb³⁺:Y₂O₃ ceramics sintered at 1850 °C for 9 h was about 7 μm. The highest transmittance of as-prepared 1 mm thickness samples around wavelength of 1050 nm reached 80%, which is close to the theoretical value of Y₂O₃. The optical spectroscopic properties of Yb³⁺:Y₂O₃ transparent ceramics have also been investigated, which shows that it is a very good laser material for diode laser pumping and short pulse mode-locked laser.     

High optical quality Y2O3 transparent ceramics with fine grain size fabricated by low temperature air pre-sintering and post-HIP treatment

High optical quality Y₂O₃ transparent ceramics with fine grain size were successfully fabricated by air pre-sintering at various temperature ranging from 1500 to 1600 °C combined with a post-hot-isostatic pressing (HIP) treatment using co-precipitated powders as the starting material. The fully dense Y₂O₃ transparent ceramic with highest transparency was obtained by pre-sintered at 1550 °C for 4 h in air and post-HIPed at 1600 °C for 3 h (the pressure of HIP 200 MPa), and it had fine microstructure and the average grain size was 0.96 μm. In addition, the in-line transmittance of the ceramic reached 81.7% at 1064 nm (1 mm thickness). By this approach, the transparent Y₂O₃ ceramics with fine grain size (<1.6 μm) were elaborated without any sintering aid.     

The effect of silica doping on neodymium diffusion in yttrium aluminum garnet ceramics: implications for sintering mechanisms

The Nd³⁺ cation diffusion into transparent polycrystalline YAG (Y₃Al₅O₁₂) was investigated as a function of temperature and silica content. Thin neodymium oxide layers were deposited on sintered YAG substrates prior to annealing under air at temperatures from 1400 to 1600 °C. Bulk and grain boundary neodymium diffusion coefficients were measured by secondary ion mass spectrometry. The experimental results show that silica addition increases the diffusivity of Nd³⁺ by a factor 10 whatever the diffusion path, probably as a result of extrinsic point defects formation, especially rare-earth vacancies.The experimental diffusion data were used to elucidate the sintering mechanism of Nd:YAG ceramics in the temperature range 1450–1550 °C. Firstly, it appeared that the intermediate stage of solid-state sintering should be controlled by the rare-earth diffusion along the grain boundary with an activation energy of about 600 kJ mol^?1. Secondly, grain growth mechanism at the final stage of liquid-phase sintering was investigated for silica-doped Nd:YAG samples. Thus, the grain growth should be limited by the reaction at interfaces at a temperature lower than 1500 °C, with an activation energy of about 880 kJ mol^?1. At higher temperature, it seems to be limited by the ionic diffusion through the intergranular liquid phase, with an activation energy of 250 kJ mol^?1.     

Rare-earth element doped Si3N4/SiC micro/nano-composites—RT and HT mechanical properties

Dense Si₃N₄/SiC micro/nano-composites with varying grain boundary phase composition were fabricated by hot-pressing under the same conditions. Six different sintering aids (Lu₂O₃, Yb₂O₃, Y₂O₃, Sm₂O₃, Nd₂O₃ and La₂O₃) were used. The formation of SiC nano-inclusions was achieved by in situ carbothermal reduction of SiO₂ by C during the sintering process. Room temperature, fracture toughness, hardness and strength tended to increase when the cation radius of the rare-earth element used in the oxide additive decreased (i.e. from La³⁺ to Lu³⁺). The composite material with Lu₂O₃ sintering additive showed the highest hardness and had reasonably high fracture toughness and strength. The same micro/nano-composite also possessed the highest creep resistance in the temperature range from 1250 °C to 1400 °C and with loads in the range 50–150 MPa.     

Diffusion of niobium in yttria-stabilized zirconia and in titania-doped yttria-stabilized zirconia polycrystalline materials

Bulk and grain boundary diffusion of Nb⁵⁺ cations in yttria-stabilized zirconia (YSZ, 8 mol% Y₂O₃–92 mol% ZrO₂) and in titania-doped yttria-stabilized zirconia (Ti–YSZ, 5 mol% TiO₂–8 mol% Y₂O₃–87 mol% ZrO₂) was studied in air in the temperature range from 900 to 1300 °C. Experiments were performed in the B-type kinetic region. Diffusion profiles were determined using the secondary ion mass spectrometry (SIMS). The temperature dependencies of the bulk diffusion coefficient D and the grain boundary diffusion parameter D′δs for both the materials were calculated. The activation energies of these transport processes in YSZ amounts to 258 and 226 kJ mol⁻¹, respectively, and 232 and 114 kJ mol⁻¹ in Ti–YSZ. The results were compared to the diffusion data of other cations previously obtained for the same material.     

Spark plasma sintering of Sm2O3-doped aluminum nitride

The high sintering temperature required for aluminum nitride (AlN) at typically 1800 °C, is an impediment to its development as an engineering material. Spark plasma sintering (SPS) of AlN is carried out with samarium oxide (Sm₂O₃) as sintering additive at a sintering temperature as low as 1500–1600 °C. The effect of sintering temperature and SPS cycle on the microstructure and performance of AlN is studied. There appears to be a direct correlation between SPS temperature and number of repeated SPS sintering cycle per sample with the density of the final sintered sample. The addition of Sm₂O₃ as a sintering aid (1 and 3 wt.%) improves the properties and density of AlN noticeably. Thermal conductivity of AlN samples improves with increase in number of SPS cycle (maximum of 2) and sintering temperature (up to 1600 °C). Thermal conductivity is found to be greatly improved with the presence of Sm₂O₃ as sintering additive, with a thermal conductivity value about 118 W m⁻¹ K⁻¹) for the 3 wt.% Sm₂O₃-doped AlN sample SPS at 1500 °C for 3 min. Dielectric constant of the sintered AlN samples is dependent on the relative density of the samples. The number of repeated SPS cycle and sintering aid do not, however, cause significant elevation of the dielectric constant of the final sintered samples. Microstructures of the AlN samples show that, densification of AlN sample is effectively enhanced through increase in the operating SPS temperature and the employment of multiple SPS cycles. Addition of Sm₂O₃ greatly improves the densification of AlN sample while maintaining a fine grain structure. The Sm₂O₃ dopant modifies the microstructures to decidedly faceted AlN grains, resulting in the flattening of AlN–AlN grain contacts.     

Mechanical and optical properties of spark plasma sintered transparent Y2O3 ceramics

Commercial Y₂O₃ nanopowder was used to fabricate transparent Y₂O₃ ceramics by spark plasma sintering under the pressure of 100 MPa for 20 min with the heating rate of 100 °C/min. The microstructures, mechanical and optical properties of the Y₂O₃ ceramics sintered at different temperatures were investigated in detail. Densification occurred up to a sintering temperature of 1500 °C, and above 1500 °C, rapid grain growth and pore growth occurred. The highest relative density of 99.58% and the minimum average grain size of 0.58±0.11 µm were obtained at 1500 °C. The flexural strength, hardness and fracture toughness of the optimal spark plasma sintered Y₂O₃ ceramic were 122 MPa, 7.60 GPa and 2.06 MPa.m^1/2, respectively. The Y₂O₃ ceramic sintered at 1500 °C had the in-line transmission of about 11–54% and 80% in the wavelength range of 400–800 nm and 3–5 µm, respectively.     

Effects of ZrO2-La2O3 co-addition on the microstructural and optical properties of transparent Y2O3 ceramics

Commercial Y₂O₃ powder was used to fabricate Y₂O₃ ceramics sintered at 1600 °C and 1800 °C with concurrent addition of ZrO₂ and La₂O₃ as sintering aids. One group with different contents of La₂O₃ (0–10 mol%) with a fixed amount of 1 mol% ZrO₂ and another group with various contents of ZrO₂ (0–7 mol%) with a fixed amount of 10 mol% La₂O₃ were compared to investigate the effects of co-doping on the microstructural and optical properties of Y₂O₃ ceramics. At low sintering temperature of 1600 °C, the sample single doped with 10 mol% La₂O₃ exhibits much denser microstructure with a few small intragranular pores while the samples with ZrO₂ and La₂O₃ co-doping features a lot of large intergranular pores leading to lower density. When the sintering temperature increases to 1800 °C, samples using composite sintering aids exhibit finer microstructures and better optical properties than those of both ZrO₂ and La₂O₃ single-doped samples. It was proved that the grain growth suppression caused by ZrO₂ overwhelms the acceleration by La₂O₃. Meanwhile, 1 mol% ZrO₂ acts as a very important inflection point with regard to the influence of additive concentration on the transmittance, pore structure and grain size. The highest in-line transmittance of Y₂O₃ ceramic (1.2 mm in thickness) with 3 mol% of ZrO₂ and 10 mol% of La₂O₃ sintered at 1800 °C for 16 h is 81.9% at a wavelength of 1100 nm, with an average grain size of 11.2 µm.     

Densification behaviour and microstructural development in undoped yttria prepared by flash-sintering

Conventional sintering of undoped Y₂O₃ requires temperatures above 1400 °C for a few hours. We show that it can be sintered nearly instantaneously to nearly full density at furnace temperature of 1133 °C under a DC applied field of 500 V/cm. At 1000 V/cm sintering occurs at 985 °C. The FLASH event, when sintering occurs abruptly, is preceded by gradually accelerated field-assisted sintering (FAST). This hybrid behaviour differs from earlier work on yttria-stabilized zirconia where all shrinkage occurred in the flash mode. The microstructure of flash-sintered specimens indicated that densification was accompanied by rapid grain growth. The single-phase nature of flash-sintered Y₂O₃ was confirmed by high-resolution transmission electron microscopy. The non-linear rise in conductivity accompanying the flash led to Joule heating. It is postulated that densification and grain growth were enhanced by accelerated solid-state diffusion, resulting from both Joule heating and the generation of defects under the applied field.     

The influence of MgO,Y2O3 and ZrO2 additions on densification and grain growth of submicrometre alumina sintered by SPS and HIP

Spark plasma sintering followed by hot isostatic pressing was applied for preparation of polycrystalline alumina with submicron grain size. The effect of additives known to influence both densification and grain growth of alumina, such as MgO, ZrO₂ and Y₂O₃ on microstructure development was studied. In the reference undoped alumina the SPS resulted in some microstructure refinement in comparison to conventionally sintered materials. Relative density >99% was achieved at temperatures >1200 °C, but high temperatures led to rapid grain growth. Addition of 500 ppm of MgO, ZrO₂ and Y₂O₃ led, under the same sintering conditions, to microstructure refinement, but inhibited densification. Doped materials with mean grain size <400 nm were prepared, but the relative density did not exceed 97.9%. Subsequent hot isostatic pressing (HIP) at 1200 and 1250 °C led to quick attainment of full density followed by rapid grain growth. The temperature of 1250 °C was required for complete densification of Y₂O₃ and ZrO₂-doped polycrystalline alumina by HIP (relative density >99.8%), and resulted in fully dense opaque materials with mean grain size<500 nm.     

Fabrication and properties of Y2O3 transparent ceramic by sintering aid combinations

Transparent Y₂O₃ ceramics were fabricated by the solid-state reaction and vacuum sintering method using La₂O₃, ZrO₂ and Al₂O₃ as sintering aids. The microstructure of the Y₂O₃ ceramics sintered from 1550 °C to 1800 °C for 8 h were analyzed by SEM. The sintering process of the Y₂O₃ transparent ceramics was optimized. The results showed that when the samples were sintered at 1800 °C for 8 h under vacuum, the average grain sizes of the ceramics were about 3.5 µm. Furthermore, the transmittance of Y₂O₃ ceramic sintered at 1800 °C for 8 h was 82.1% at the wavelength around the 1100 nm (1 mm thickness), which was close to its theoretical value. Moreover, the refractive index of the Y₂O₃ transparent ceramic in the temperature range from 30 °C to 400 °C were measured by the spectroscopic ellipsometry method.     

Effect of Fe2O3 doping on sintering of yttria-stabilized zirconia

This paper reports the effect of Fe₂O₃ doping on the densification and grain growth in yttria-stabilized zirconia (YSZ) during sintering at 1150 °C for 2 h. Fe₂O₃ doped 3 mol% YSZ (3YSZ) and 8 mol% YSZ (8YSZ) coatings were produced using electrophoretic deposition (EPD). For 0.5 mol% Fe₂O₃ doping, both 3YSZ and 8YSZ coatings during sintering at 1150 °C has similar densification. However, a significant grain growth occurred in 8YSZ during sintering, whereas grain size remains almost constant in 3YSZ. XRD results suggest that Fe₂O₃ addition substitutionally and interstitially dissolved into the lattice of 3YSZ and 8YSZ. In addition, colour of 3YSZ and 8YSZ changes differently with doping of Fe₂O₃. A Fe³⁺ ion interstitial diffusion mechanism is proposed to explain the densification and grain growth behaviour in the Fe₂O₃ doped 3YSZ and 8YSZ. A retard grain growth observed in the Fe₂O₃ doped 3YSZ is attributed to Fe³⁺ segregation at grain boundary.     

Novel amorphous precursor densification to transparent Nd:Y2O3 Ceramics

A novel approach of neodymium ion doped yttrium oxide (Nd:Y₂O₃) amorphous precursor compaction and sintering is being reported for the first time. Precursor of 2 at.% Nd³⁺ doped Y₂O₃ was synthesized by gelation of sol of yttrium and neodymium nitrates with l-alanine at 80 °C for 16 h followed by gel combustion in microwave. A part of microwave precursor was heat treated at 700 °C for 5 h to give the partially crystalline Nd:Y₂O₃ amorphous precursor. Thermogravimetric analysis (TGA) of partially crystalline amorphous precursor of Nd:Y₂O₃ gave 8.5% total weight loss indicating removal of maximum organics. X-Ray diffraction (XRD) showed broad peaks indicating incomplete crystallization of cubic Nd:Y₂O₃. Morphology was found to be close to spherical with particles in size range 17–19 nm by TEM. Another part of microwave precursor on calcination at 1000 °C for 3 h led to formation of fully crystalline Nd:Y₂O₃ with particles in size range of 35–85 nm. Both partially crystalline amorphous precursor and fully crystalline Nd:Y₂O₃ were compacted at 400 MPa by cold isostatic press and sintered at 1750 °C for 10 h under vacuum (10^?5 mbar). The partially crystalline Nd:Y₂O₃ amorphous precursor densified to 99% with 65% transmission at 2500 nm (0.5 mm thickness) compared to 96% densification with 34% transmission for fully crystalline Nd:Y₂O₃ without any sintering aids. Retention of cubic phase purity of Y₂O₃ was observed in both the ceramic pellets post sintering by XRD. Good grain fusion with grain growth to ≤2 μm was observed by scanning electron microscope (SEM) for partially crystalline Nd:Y₂O₃ amorphous precursor. Thus partially crystalline Nd:Y₂O₃ amorphous precursor nanopowders, with homogeneous close to spherical fine particles and high reactivity due to ionic mobility of amorphous phase, led to better densification.     

Microstructural evolution of nanocrystalline Al2O3 sintered at a high heating rate

Experimental sintering studies on Al₂O₃ powder (200 nm and 600 nm) were done at a heating rate of 1600 °C/min. The microstructural changes of specimens were examined and corresponding detailed data on the densification and grain size as a function of sintering time were presented. The grain-growth transition behavior during sintering was discussed. The results showed that the neck growth caused principally by surface diffusion could be negligible within 2 min. With subsequent increases of sintering time, grain growth promoted by grain boundary and lattice diffusion occurred.     

The sintering behavior,microstructure, and electrical properties of gallium-doped zinc oxide ceramic targets

The properties of sputtering targets have recently been found to affect the performances of sputtered films and the sputtering process. To develop high-quality GZO ceramic targets, the influences of Ga₂O₃ content and sintering temperature on the sintering behavior, microstructure, and electrical properties of GZO ceramic targets were studied.The results showed that the increase in Ga₂O₃ content from 3 wt% (GZO-3Ga) and 5 wt% (GZO-5Ga) not only inhibited the densification but retarded grain growth. During sintering, ZnGa₂O₄ phase formed before 800 °C, and Zn₉Ga₂O₁₂ phase was found after sintering at 1000 °C. Moreover, after sintering at 1200 °C, the number of Zn₉Ga₂O₁₂ precipitates increased at the expense of ZnGa₂O₄ and ZnGa₂O₄ disappearing completely. The relative density, grain size, and resistivity of GZO-3Ga sintered at 1400 °C in air were 99.3%, 3.3 μm, and 2.8 × 10⁻³ Ω cm, respectively. These properties of GZO ceramics are comparable to properties reported in the literature for AZO sintered in air.     

Inhibition of grain growth in liquid-phase sintered SiC ceramics by AlN additive and spark plasma sintering

SiC ceramics were prepared from nanosized β-SiC powder with different compositions of AlN and Y₂O₃ sintering additives by spark plasma sintering (SPS) at 1900 °C for 600 s in N₂. The relative density of the sintered SiC specimens increased with increasing amount of AlN, reaching a relative density higher than 99%, while at the same time grain size decreased significantly. The smallest average grain size of 150 nm was observed for SiC sample sintered with 10 vol% of additives consisting of 90 mol% AlN and 10 mol% Y₂O₃. Fully dense nanostructured SiC ceramics with inhibited grain growth were obtained by the AlN additive and SPS technique. The flexural strength of the SiC body containing 70 mol% AlN and 30 mol% Y₂O₃ additives reached the maximum value of 1000 MPa. The SiC bodies prepared with AlN and Y₂O₃ additives had the fracture toughness of around 2.5 MPam^1/2.     

Densification behavior and microstructure evolution of yttrium-doped ThO2 ceramics

Sintering of Th_1-xY_xO_2-x/2 ceramics (x = 0.01, 0.08, 0.15 and 0.22), planned to be used as solid electrolytes in oxygen sensors for sodium-cooled fast nuclear reactors, was investigated. High densification state (i.e. up to 98% TD) was reached after 4 h of heat treatment at 1600 °C and beyond. In addition, ESEM observations showed a major effect of yttrium on grain size due to solute drag effects. Sintering maps were plotted for all the samples and evidenced different stages driven by densification and grain growth. Grain growth was found to be strongly slowed down for x > 0.01, resulting in high values of relative density correlated to submicrometric grain size. Also, activation energies related to densification and grain growth were evaluated around 450 and 500–650 kJ mol⁻¹, respectively. These results led to deliver guidelines for the formulation and sintering of Th_1-xY_xO_2-x/2 ceramics in prospect of their use as a solid electrolyte.