Dielectric properties of nano-sized Ba0.7Sr0.3TiO3 powders prepared by spray pyrolysis

Nano-sized Ba_0.7Sr_0.3TiO₃ powders are prepared by post-treatment of the precursor powders with hollow and thin wall structure at temperatures between 900 and 1100 °C. Ethylenediaminetetraacetic acid and citric acid improve the hollowness of the precursor powders prepared by spray pyrolysis. The mean sizes of the powders post-treated at temperatures of 900, 1000 and 1100 °C are 42, 51 and 66 nm, respectively. The densities of the Ba_0.7Sr_0.3TiO₃ pellets obtained from the powders post-treated at 900, 1000 and 1100 °C are each 5.36, 5.55 and 5.38 g cm^?3 at a sintering temperature of 1300 °C. The pellet obtained from the powders post-treated at 1000 °C has higher maximum dielectric constant than those obtained from the powders post-treated at 900 and 1100 °C.     

Synthesis of triclinic and hexagonal SmBO3 powders by mechanically activated annealing of Sm2O3 and B2O3 blends

Samarium borate (SmBO₃) powders were fabricated from oxide raw materials by a two-step solid-state synthesis method including mechanical activation and annealing. Blends containing stoichiometric amounts of samarium oxide (Sm₂O₃) and boron oxide (B₂O₃) were mechanically activated in a high-energy ball mill and subsequently annealed in air. Afterwards, mechanically activated and annealed powders were washed with distilled water in order to remove probable unreacted B₂O₃ phase. The effects of mechanical activation duration (15 min, 1 h, 3 h and 9 h) and annealing temperature (700–1250 °C) on the resultant powders were investigated. Compositional, microstructural, physical, thermal and optical properties of the powders obtained throughout the different process steps were characterized by using an X-ray diffractometry (XRD), particle size analysis (PSA), stereomicroscopy (SM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), gas pycnometry, differential scanning calorimetry (DSC), heating stage microscopy (HSM), atomic absorption spectrometry (AAS), Fourier transform infrared (FTIR) spectrometry and ultraviolet-visible spectrophotometry (UV–vis) techniques. Fine-grained and pure SmBO₃ powders were successfully synthesized via a simple, feasible and scalable route, yielding both triclinic and hexagonal crystal structures. Triclinic SmBO₃ powders were synthesized after mechanical activation for 1 h and annealing at 700 °C for 2 h. The polymorphic transformation temperature of SmBO₃ powders from triclinic to hexagonal is about 1080 °C. Due to the effect of mechanical activation, the synthesis of triclinic SmBO₃ phase and its transformation to hexagonal form were found to take place at ∼50–100 °C lower temperatures than those reported in other methods. Mainly hexagonal SmBO₃ powders were obtained after annealing at 1150 °C in the presence of a very small amount of triclinic SmBO₃. The resultant powders showed intense UV absorptions in the range between 1025 and 1150 nm with minimum reflectivity of 0.57% (triclinic SmBO₃ phase) and 0.68% (hexagonal SmBO₃ phase) depending on their crystal structures.     

Synthesis of ultra-fine hafnium carbide powders combining the methods of liquid precursor conversion and plasma activated sintering

Ultra-fine hafnium carbide (HfC) powders were synthesized using a novel method combining liquid precursor conversion and plasma activated sintering (PAS). Solution-based processing was used to achieve a fine-scale mixing of the reactants, and further treatment by PAS allowed fast formation of HfC. We investigated the effect of the type of acid used during the liquid precursor conversion on the synthesized powders, where mixtures were prepared using salicylic acid, citric acid, or a combination of these. The results show that pure HfC powders (with an average particle sizes of 350 nm) were obtained at a relatively low temperature (1550 °C) using a HfOCl₂·8H₂O precursor with the mixed acids. The oxygen content of the synthesized powders was only 0.97 wt%. The type of acid had a significant effect on the synthesis product. When using only citric acid, the temperature required to produce pure hafnium carbide increased to 1700 °C. In the case of a salicylic acid precursor, pure HfC was not obtained, even at a synthesis temperature of 1700 °C.     

Low-temperature molten salt synthesis of YAlO3 powders assisted by an electrochemical process

YAlO₃ (YAP) powders were successfully synthesized by a unique molten salt method, where YAP precursor was prepared by an electrochemical method at room temperature, followed by calcining it at a temperature of not exceeding 400 °C for 8 h using LiNO₃ as the molten salt medium. XRD analysis and TEM observation show that well-crystallized YAP powders can be obtained at 400 °C for a holding time of 8 h with 1:16 ratio of YAP precursor to LiNO₃ by weight. Greatly reduced temperature of forming YAP should be attributed to the incorporation of LiNO₃ salt in preparing process.     

Microstructure and mechanical properties of ceramics obtained from chemically co-precipitated Al2O3-GdAlO3 nano-powders with eutectic composition

An efficient and flexible chemical co-precipitation method has been used to synthesize nanoscale Al₂O₃-GdAlO₃ powders with eutectic composition. The as-synthesized powders exhibit a highly dispersive and homogeneous distribution with an average particle size of 50 nm. The phase transition in the resulting powders strongly depends upon the calcination temperature. GdAlO₃ undergoes complete crystallization after calcination at 1050 °C, however, the diffraction peaks of α-Al₂O₃ are found at a relatively high calcination temperature of at least 1300 °C. The fully-densified Al₂O₃-GdAlO₃ ceramic with eutectic composition obtained by hot pressing the nanoscale powders at 1500 °C exhibits a room temperature flexural strength of 556 MPa, a Vickers hardness of 17.3 GPa and a fracture toughness of 7.5 MPa m^1/2. The high temperature flexural strength of the as-sintered Al₂O₃-GdAlO₃ ceramic is measured to be 515 MPa after bending tests at 1000 °C.     

Pb(Zr0.95Ti0.05)O3 powders and porous ceramics prepared by one-step pyrolysis process using non-aqueous Pechini method

Using non-aqueous Pechini method, Pb(Zr_0.95Ti_0.05)O₃ powders were prepared at low temperature by one-step pyrolysis process. The polymeric gels and powders were characterized using a range of techniques, such as DTG, XRD, SEM, Raman spectroscopy, and laser particle size distribution. The perovskite phase was formed at about 350–400 °C and some oxocarbonate impurities can be detected in all samples after calcining at 400–850 °C by one-step pyrolysis process. Phase pure and porous Pb(Zr_0.95Ti_0.05)O₃ ceramics were obtained without pore formers from the powders by one-step pyrolysis process at 500 °C for 4 h. The relative densities were 87%, 91% and 94% for the ceramics sintered at 1100, 1150 and 1200 °C for 2 h, respectively. The porous ceramics sintered at 1200 °C for 2 h have homogeneously dispersed pores and fine-grain structures with an individual grain size of 0.7–2 μm.     

Synthesis and characterization of nanometric gadolinia powders by room temperature solid-state displacement reaction and low temperature calcination

Nanometric-sized gadolinia (Gd₂O₃) powders were obtained by applying solid-state displacement reaction at room temperature and low temperature calcination. The XRD analysis revealed that the room temperature product was gadolinium hydroxide, Gd(OH)₃. In order to induce crystallization of Gd₂O₃, the subsequent calcination at 600 ∼ 1200 °C of the room temperature reaction products was studied. Calculation of average crystallite size (D) as well as separation of the effect of crystallite size and strain of nanocrystals was performed on the basic of Williamson-Hall plots. The morphologies of powders calcined at different temperatures were followed by scanning electron microscopy. The pure cubic Gd₂O₃ phase was made at 600 °C which converted to monoclinic Gd₂O₃ phase between 1400° and 1600 °C. High-density (96% of theoretical density) ceramic pellet free of any additives was obtained after pressureless sintering at 1600 °C for 4 h in air, using calcined powder at 600 °C.     

Transparent mullite ceramic from single-phase gel by Spark Plasma Sintering

Monophasic mullite precursors with composition of 3Al₂O₃·2SiO₂ (3:2) were synthesized and then were sintered by Spark Plasma Sintering (SPS) to form transparent mullite ceramics. The precursor powders were calcined at 1100 °C for 2 h. The sintering was carried out by heating the sample to 1450 °C, holding for 10 min. The sintered body obtained a relative bulk density of above 97.5% and an infrared transmittance of 75–82% in wavelength of 2.5–4.3 μm without any additive. When the precursor powders were calcined at below 1100 °C, it was unfavorable for completely eliminating the residual OH, H₂O and organic compound. However, when calcined temperature was too high, it was unfavorable either for full densification due to the absence of viscous flow of amorphous phase. At the same calcined temperature, the transmittance of sintered body was decreased with the increase of the sintering temperature above 1450 °C owing to the elongated grain growth.     

Synthesis of nanosized zirconium carbide powders by a combinational method of sol–gel and pulse current heating

Zirconium carbide nanopowders were synthesized by a novel method combining the advantages of sol–gel method and rapid synthesis using pulse current heating. The core-shelled structure of ZrO₂/C mixture was obtained during the sol–gel process, and further heat treatment in SPS led to the fast formation of ZrC. The particle size of ZrO₂ played an important role in the synthesis of nanosized ZrC powders. In addition, the coalescence and grain growth of ZrC particles could be also limited due to the fast heating rate. As a result, the reactions were thoroughly completed at a relatively low temperature and ZrC nanopowders of 60–100 nm were obtained. The corresponding powders also had low oxygen content (∼0.64 wt%) and residual carbon content (∼0.27 wt%). Additive-free ZrC powders could be sintered to ∼99% relative density with an average grain size of 0.8 μm at low temperature of 1750 °C.     

Nanosized barium ferrite powders prepared by spray pyrolysis from citric acid solution

Highly crystalline nanosized barium ferrite (BaFe₁₂O₁₉) powders were prepared by spray pyrolysis from a spray solution containing a high concentration of the metal components. The precursor powders obtained from the spray solution containing citric acid were amorphous with a porous and hollow structure. Purely crystalline and fine BaFe₁₂O₁₉ powders were obtained after post-treatment between 700 and 1000 °C and subsequent mechanical grinding in an agate mortar. The mean sizes of the powders post-treated at 700 and 1000 °C were 125 and 550 nm, respectively. The specific magnetization of the powders prepared from the spray solution containing citric acid was 57 emu/g.     

Preparation of calcium doped LaCrO3 fine powders by hydrothermal method and its sintering

The synthesis of fine powders of LaCrO₃ and its solid solutions doped with calcium under hydrothermal conditions and the sintering of these powders were investigated. Precursor alkaline coprecipitated lanthanum chromite gels with three different compositions: LaCrO₃, La_0.9Ca_0.1CrO₃ and La_0.8Ca_0.2CrO₃, were processed under hydrothermal conditions at low temperatures (350–425 °C), for a reaction time between 30 and 120 min. Powders of a single phase with orthorhombic structure of LaCrO₃, La_0.9Ca_0.1CrO₃ and La_0.8Ca_0.2CrO₃ were obtained at a temperature as low as 350, 400 and 425 °C, respectively, for a short reaction interval of 1 h. SEM and TEM micrographs showed that particles with an irregular morphology and an average particle size of 300 nm, were mainly obtained under hydrothermal conditions. The powders were pressed by cold isostatic pressing at 200 MPa, and then sintered in air at a temperature range of 1200–1500 °C for various intervals (1 to 5 h). A maximum apparent density of 97.7% was achieved on specimens with high calcium content, La_0.8Ca_0.2CrO₃, at 1400 °C for 5 h. The average grain size measured on the sintered specimens was 6 μm.     

Comparison among different sintering routes for preparing alumina-YAG nanocomposites

Al₂O₃-YAG (50 vol.%) nanocomposite powders were prepared by wet-chemical synthesis and characterized by DTA-TG, XRD and TEM analyses. Amorphous powders were pre-heated at different temperatures (namely 600 °C, 800 °C, 900 °C and 1215 °C) and the influence of this thermal treatment on sintering behavior, final microstructure and density was investigated. The best performing sample was that pre-calcined at 900 °C, which yields dense bodies with a micronic/slightly sub-micronic microstructure after sintering at 1600 °C. A pre-treatment step to induce controlled crystallisation of the amorphous powder as well as a fast sintering procedure for green compacts, were also performed as a comparison.Finally, the previously stated thermal pre-treatment of the amorphous product was coupled to an extensive mechanical activation performed by wet planetary/ball milling. This procedure was highly effective in lowering the densification temperature, so that fully dense Al₂O₃-YAG composites, with a mean grain size smaller than 200 nm, were obtained by sintering in the temperature range 1370–1420 °C.     

Low temperature pressureless sintering of dense silicon nitride using BaO-Al2O3-SiO2 glass as sintering aid

Dense Si₃N₄ ceramic with BaO-Al₂O₃-SiO₂ low temperature glass powders as sintering aids were prepared by pressureless sintering techniques at a relatively low temperature (1550 °C). Four kinds of glass powders of compositions melting at 1120 °C, 1300 °C, 1400 °C and 1500 °C, respectively, have been introduced as sintering aids. XRD results demonstrate that the BaO-Al₂O₃-SiO₂ glass powders reacted with BaAl₂O₄ and converted into hexagonal celsian, which is a high-temperature phase with melting point of 1760 °C, so being beneficial to the high temperature properties of the materials. In addition, a portion of α-Si₃N₄ transformed to rod like β-Si₃N₄ with high aspect ratio as shown by XRD and SEM analysis. The bulk density increased with the rise of the melting temperature of the BaO-Al₂O₃-SiO₂ glass powders, the sample obtained with the BaO-Al₂O₃-SiO₂ glass powder melting at 1500 °C reaching a maximum density of 98.8%, an high flexural strength (373 MPa) and a fracture toughness (4.8 MPa m^1/2).     

Melting salt assisted sol–gel synthesis of blue phosphor Y2SiO5:Ce

High brightness Y₂SiO₅:Ce phosphor powders with spherical shape and fine size were synthesized by melting salt assisted sol–gel method (MS&Sol–Gel). Commercial tetraethyl orthosilicate was used as the silica source and rare earth oxides were used as rare earth source. The prepared Y₂SiO₅:Ce powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), laser particle sizer, and fluorescentometer techniques. Y₂SiO₅:Ce powders were obtained at significantly lower temperature than that by conventional techniques. When sintered at 1200 °C for 2 h with 5 wt.% LiF and 2 wt.% KH₂PO₄ as fluxes, particles with spherical shape and narrow particle distribution could be obtained. Moreover, the grain size of the powders prepared through this process was in the range of 2–7 μm, strongly depending on the thermal treatments and the species of fluxes. PL intensity of the prepared Y₂SiO₅:Ce phosphor using 5 wt.% LiF and 2 wt.% KH₂PO₄ as fluxes was similar to that of commercial product.     

Characteristics of BaNd2Ti5O14 powders directly prepared by high-temperature spray pyrolysis

BaNd₂Ti₅O₁₄ powders were directly prepared by high-temperature spray pyrolysis. The powders prepared at temperatures of 1300 and 1500 °C exhibited a pure BaNd₂Ti₅O₁₄ phase. The powders prepared at 1300 °C were spherical in shape. However, the powders prepared at 1500 °C showed non-spherical shapes. The BaNd₂Ti₅O₁₄ powders had a composition similar to that of the spray solution. The mean sizes of the BaNd₂Ti₅O₁₄ powders increased from 0.23 to 0.60 μm when the concentration of the spray solution was increased from 0.01 to 0.2 M. At a sintering temperature of 1100 °C, bridge-like structures were formed between the powders. Pellets sintered at 1300 °C exhibited a dense structure comprising rod-like crystals.     

Dielectric and magnetic properties of BiFeO3 ceramics prepared by hydrothermal synthesis

Single-phase BiFeO₃ powders were prepared at a temperature of 200 °C by a hydrothermal synthesis. BiFeO₃ ceramics were prepared with the powders by a conventional ceramic process. The BiFeO₃ ceramics with no impurity phase were prepared at the sintering temperature of 650–800 °C. The dense microstructure was observed in the BiFeO₃ ceramics sintered at a temperature of 700 °C and higher. BiFeO₃ ceramics show linear M–H curves in low H, which are antiferromagnetic behaviors. The dielectric dispersion was observed at the frequency range of 10 kHz to 1 MHz in the BiFeO₃ ceramic sintered at 700 °C or lower. The dielectric constant and loss of the BiFeO₃ ceramics sintered at 750 °C or higher were about 85 and 0.4 at 100 kHz, respectively.     

Mechanical activation-assisted autoclave processing and sintering of HfB2-HfO2 ceramic powders

This study reports on the synthesis and consolidation of HfB₂-HfO₂ ceramic powders via mechanical activation-assisted autoclave processing followed by pressureless sintering (PS) or spark plasma sintering (SPS). HfCl₄, B₂O₃ and Mg starting powders were mechanically activated for 5 min to obtain homogeneously blended precursors with active particle surfaces. Autoclave synthesis was carried out at a relatively low temperature at 500 °C for 6 or 12 h. As-synthesized powders were purified from reaction by-products such as MgO and MgCl₂ by washing and acid leaching treatments. The characterization investigations of the as-synthesized and purified powders were performed by using an X-ray diffractometer (XRD), stereomicroscope (SM), scanning electron microscope (SEM) and particle size analyzer (PSA). The purified powders with an average particle size of about 190 nm comprised the HfB₂ phase with an amount of 79.6 wt% in addition to the HfO₂ phase and a very small amount of Mg₂Hf₅O₁₂ phase after mechanical activation for 5 min and autoclave processing for 12 h. They were consolidated at 1700 °C both by PS for 6 h and SPS for 15 min. The Mg₂Hf₅O₁₂ phase decomposed during sintering and bulk samples only had the HfB₂ and HfO₂ phases. The bulk properties of the sintered samples were characterized in terms of microstructure, density, microhardness and wear characteristics. The HfB₂-HfO₂ ceramics consolidated by PS exhibited poor densification rates. A considerable improvement was obtained in the relative density (~91%), microhardness (~16 GPa) and relative wear resistance (2.5) values of the HfB₂-HfO₂ ceramics consolidated by SPS.     

Low-temperature combustion synthesis of nanocrystalline HoFeO3 powders via a sol–gel method using glycin

Single phase nanocrystalline HoFeO₃ powders were successfully synthesized by the sol–gel self-propagation combustion method using glycin (C₂H₅NO₂) as the chelating reagent at a low combustion temperature. Four different mole ratios of glycin to metal nitrate (G/M) were used to prepare HoFeO₃ powders in the experiment. The XRD patterns indicate monophasic HoFeO₃ powders can be formed by further calcination, the SEM micrographs show that the nano-sized grains with distinguishable boundaries had been obtained. The M–H curves show HoFeO₃ powders had the characteristic of antiferromagnetism at 50 K, while the powders had the characteristic of paramagnetism as the ambient temperature reached 100 K or 300 K. The FC/ZFC magnetic measurement results demonstrate that there was a transition from antiferromagnetism to paramagnetism in HoFeO₃ nanopowders as the temperature was increased.     

Highly transparent AlON ceramics sintered from powder synthesized by carbothermal reduction nitridation

Aluminum oxynitride (AlON) powders were synthesized by the carbothermal reduction and nitridation process using commercial γ-Al₂O₃ and carbon black powders as starting materials. And AlON transparent ceramics were fabricated by pressureless sintering under nitrogen atmosphere. The effects of ball milling time on morphology and particle size distribution of the AlON powders, as well as the microstructure and optical property of AlON transparent ceramics were investigated. It is found that single-phase AlON powder was obtained by calcining the γ-Al₂O₃/C mixture at 1550 °C for 1 h and a following heat treatment at 1750 °C for 2 h. The AlON powder ball milled for 24 h showed smaller particles and narrower particle size distribution compared with the 12 h one, which was benefit for the improvement of optical property of AlON transparent ceramics. With the sintering aids of 0.25 wt% MgO and 0.04 wt% Y₂O₃, highly transparent AlON ceramics with in-line transmittance above 80% from visible to infrared range were obtained through pressureless sintering at 1850 °C for 6 h.     

Effect of calcination temperature on structural,magnetic and optical properties of multiferroic YFeO3 nanopowders synthesized by a low temperature solid-state reaction

Nanosize multiferroic YFeO₃ powders have been synthesized via the low temperature solid-state reaction. Differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy all indicated that the phase-pure orthorhombic YFeO₃ powders were obtained at 800 °C with a size below 150 nm. X-ray photoelectron spectroscopy (XPS) showed the Fe³⁺ ions to be predominant. Magnetic hysteresis loops exhibited some ferromagnetic behaviour of the YFeO₃ nanopowders at ambient temperature. The maximum and remnant magnetizations of the powders were about 2.49 and 0.88 emu/g, respectively. Moreover, optical measurements demonstrated that the optical band gap of the nanopowders was around 2.4 eV, proving that they can strongly absorb visible light. So an easy and efficient way to synthesize YFeO₃ nanopowders with promising application in the magnetic and optical fields has been successfully developed.