Sintering,microstructure and mechanical properties of Al2O3–Y2O3–ZrO2 (AYZ) eutectic composition ceramic microcomposites

We report on how the mechanical properties of sintered ceramics (i.e., a random mixture of equiaxed grains) with the Al₂O₃–Y₂O₃–ZrO₂ eutectic composition compare with those of rapidly or directionally solidified Al₂O₃–Y₂O₃–ZrO₂ eutectic melts. Ceramic microcomposites with the Al₂O₃–Y₂O₃–ZrO₂ eutectic composition were fabricated by sintering in air at 1400–1500 °C, or hot pressing at 1300–1400 °C. Fully dense, three phase composites of Al₂O₃, Y₂O₃-stabilized ZrO₂ and YAG with grain sizes ranging from 0.4 to 0.8 μm were obtained. The grain size of the three phases was controlled by the size of the initial powders. Annealing at 1500 °C for 96 h resulted in grain sizes of 0.5–1.8 μm. The finest scale microcomposite had a maximum hardness of 19 GPa and a four-point bend strength of 282 MPa. The fracture toughness, as determined by Vickers indentation and indented four-point bending methods, ranged from 2.3 to 4.7 MPa m^1/2. Although strengths and fracture toughnesses are lower than some directionally or rapidly solidified eutectic composites, the intergranular fracture patterns in the sintered ceramic suggest that ceramic microcomposites have the potential to be tailored to yield stronger, tougher composites that may be comparable with melt solidified eutectic composites.     

Mechanical and optical properties of spark plasma sintered transparent Y2O3 ceramics

Commercial Y₂O₃ nanopowder was used to fabricate transparent Y₂O₃ ceramics by spark plasma sintering under the pressure of 100 MPa for 20 min with the heating rate of 100 °C/min. The microstructures, mechanical and optical properties of the Y₂O₃ ceramics sintered at different temperatures were investigated in detail. Densification occurred up to a sintering temperature of 1500 °C, and above 1500 °C, rapid grain growth and pore growth occurred. The highest relative density of 99.58% and the minimum average grain size of 0.58±0.11 µm were obtained at 1500 °C. The flexural strength, hardness and fracture toughness of the optimal spark plasma sintered Y₂O₃ ceramic were 122 MPa, 7.60 GPa and 2.06 MPa.m^1/2, respectively. The Y₂O₃ ceramic sintered at 1500 °C had the in-line transmission of about 11–54% and 80% in the wavelength range of 400–800 nm and 3–5 µm, respectively.     

Spark plasma sintering of transparent Y2O3 ceramic using hydrothermal synthesized nanopowders

Y₂O₃ nanopowders were synthesized by the hydrothermal treatment of Y(NO₃)₃·6H₂O and citric acid (CA) as Y⁺³ and the capping agent, respectively. The effect of different CA:Y⁺³ mol ratios, heat treatment time, and calcination temperature was investigated in order to determine their influence on the morphology, particle size and phase of Y₂O₃ nanopowders. The narrow size distribution of particles was obtained with CA:Y⁺³ mol ratio=1.6, heat treatment time of 6 h, and a calcination temperature at 900 °C for 90 min. Then, the synthesized Y₂O₃ nanopowder was consolidated by the spark plasma sintering technique at 1500 °C with a heating rate of 100 °C/min and held for 8 min before turning off the power. As a result, the ceramic prepared with 3 mm thickness got the highest transmission of 80% at 2.5–6 µm wavelength. The highest density and the grain size of yttria ceramic were 99.58% and 1–1.2 µm at 1500 °C, respectively.     

Fabrication and properties of Y2O3 transparent ceramic by sintering aid combinations

Transparent Y₂O₃ ceramics were fabricated by the solid-state reaction and vacuum sintering method using La₂O₃, ZrO₂ and Al₂O₃ as sintering aids. The microstructure of the Y₂O₃ ceramics sintered from 1550 °C to 1800 °C for 8 h were analyzed by SEM. The sintering process of the Y₂O₃ transparent ceramics was optimized. The results showed that when the samples were sintered at 1800 °C for 8 h under vacuum, the average grain sizes of the ceramics were about 3.5 µm. Furthermore, the transmittance of Y₂O₃ ceramic sintered at 1800 °C for 8 h was 82.1% at the wavelength around the 1100 nm (1 mm thickness), which was close to its theoretical value. Moreover, the refractive index of the Y₂O₃ transparent ceramic in the temperature range from 30 °C to 400 °C were measured by the spectroscopic ellipsometry method.     

Microstructure and mechanical properties of Al2O3–20 wt%Al2TiO5 composite prepared from alumina and titania nanopowders

In the present work, Al₂O₃–20 wt%Al₂TiO₅ composite was prepared from reaction sintering of alumina and titania nanopowders. The nano-sized raw powders were reconstituted into nanostructured particles by ball milling. Then, the nanostructured reconstituted powders were pressed and pressureless-sintered into bulk ceramics at 1300, 1400, 1500 °C for 2 h. The phase composition and microstructures of reconstituted powders and as-prepared ceramic composites were characterized by using X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope and energy-dispersive spectrometer (EDS). The microstructural analysis of the ceramic showed that the average grain size of the alumina–aluminium titanate composite increases with increasing the temperature. Also, SEM proved the existence of a proper interface between Al₂TiO₅ and Al₂O₃ grains and preferential distribution of aluminium titanate particles in the grain boundaries. XRD analysis indicated the absence of rutile titania in the sintered composite ensuring complete formation of aluminium titanate. The hardness of the samples sintered at 1300, 1400, 1500 °C were 4.8, 6.2 and 8.5 GPa, respectively.     

High optical quality Y2O3 transparent ceramics with fine grain size fabricated by low temperature air pre-sintering and post-HIP treatment

High optical quality Y₂O₃ transparent ceramics with fine grain size were successfully fabricated by air pre-sintering at various temperature ranging from 1500 to 1600 °C combined with a post-hot-isostatic pressing (HIP) treatment using co-precipitated powders as the starting material. The fully dense Y₂O₃ transparent ceramic with highest transparency was obtained by pre-sintered at 1550 °C for 4 h in air and post-HIPed at 1600 °C for 3 h (the pressure of HIP 200 MPa), and it had fine microstructure and the average grain size was 0.96 μm. In addition, the in-line transmittance of the ceramic reached 81.7% at 1064 nm (1 mm thickness). By this approach, the transparent Y₂O₃ ceramics with fine grain size (<1.6 μm) were elaborated without any sintering aid.     

Doping effect of divalent cations on sintering of polycrystalline yttria

The sintering behavior of Y₂O₃ doped with 1 mol% of Ca²⁺, Mg²⁺, Mn²⁺, Ni²⁺, Sr²⁺ or Zn²⁺ was investigated by pressureless sintering in air at a sintering temperature in the range 900–1600 °C. The sintering temperature required for full densification in Y₂O₃ was reduced by 100–400 °C by the cation doping, while undoped Y₂O₃ was densified at 1600 °C. The most effective dopant among the examined cations was Zn²⁺. The grain growth kinetics of undoped and cation-doped Y₂O₃ was described by the parabolic law. The grain boundary mobility of Y₂O₃ was accelerated by doping of the divalent cations. High-resolution transmission electron microscopy (HRTEM) observations and nano-probe X-ray energy dispersive spectroscopy (EDS) analyses confirmed that the dopant cations tended to segregate along the grain boundaries without forming amorphous layers. The improved sinterability of Y₂O₃ is probably related to the accelerated grain boundary diffusion owing to the grain boundary segregation of the dopant cations.     

The effect of silica doping on neodymium diffusion in yttrium aluminum garnet ceramics: implications for sintering mechanisms

The Nd³⁺ cation diffusion into transparent polycrystalline YAG (Y₃Al₅O₁₂) was investigated as a function of temperature and silica content. Thin neodymium oxide layers were deposited on sintered YAG substrates prior to annealing under air at temperatures from 1400 to 1600 °C. Bulk and grain boundary neodymium diffusion coefficients were measured by secondary ion mass spectrometry. The experimental results show that silica addition increases the diffusivity of Nd³⁺ by a factor 10 whatever the diffusion path, probably as a result of extrinsic point defects formation, especially rare-earth vacancies.The experimental diffusion data were used to elucidate the sintering mechanism of Nd:YAG ceramics in the temperature range 1450–1550 °C. Firstly, it appeared that the intermediate stage of solid-state sintering should be controlled by the rare-earth diffusion along the grain boundary with an activation energy of about 600 kJ mol^?1. Secondly, grain growth mechanism at the final stage of liquid-phase sintering was investigated for silica-doped Nd:YAG samples. Thus, the grain growth should be limited by the reaction at interfaces at a temperature lower than 1500 °C, with an activation energy of about 880 kJ mol^?1. At higher temperature, it seems to be limited by the ionic diffusion through the intergranular liquid phase, with an activation energy of 250 kJ mol^?1.     

Enhancing the sinterability and fracture toughness of Al2O3–TiN0.3 composites

We introduce a new and effective method for improving the fracture toughness of Al₂O₃-based composites through the addition of a nonstoichiometric material. Al₂O₃–TiN_0.3 composites were sintered by spark plasma sintering with different TiN_0.3 content at temperatures between 1300 and 1600 °C for 10 min and a micro-region diffusion phenomenon was observed at the Al₂O₃–TiN_0.3 interface. Ti atoms from TiN_0.3 diffused into Al₂O₃ to occupy Al sites, which led to the formation of Al vacancies that enabled the transport of aluminum by a vacancy mechanism. The optimal densification temperature of the Al₂O₃–30vol% TiN_0.3 composite was approximately 1400 °C. The maximum fracture toughness measured was 6.91 MPa m^1/2, from the composite with 30 vol% TiN_0.3 sintered at 1500 °C.     

Dielectric and thermal properties of AlN ceramics

The effects of slow-cooling and annealing conditions on dielectric loss, thermal conductivity and microstructure of AlN ceramics were investigated. Y₂O₃ from 0.5 to 1.25 mol% at 0.25% increments was added as a sintering additive to AlN powder and pressureless sintering was carried out at 1900 °C for 2 h in a nitrogen flowing atmosphere. To improve the properties, AlN samples were slow-cooled at a rate of 1 °C min⁻¹ from 1900 to 1750 °C, subsequently cooled to 970 °C at a rate of 10 °C min⁻¹ and then annealed at the same temperature for 4 h. AlN and YAG (5Al₂O₃/3Y₂O₃) were the only identified phases from XRD. AlN doped with 0.5 and 0.75 mol% Y₂O₃ had a low loss of <2.0 × 10⁻³ and a high thermal conductivity of >160 W m⁻¹ °C⁻¹.     

Structural-phase state and lasing of 5–15 at% Yb3+:Y3Al5O12 optical ceramics

Yttrium aluminum garnet (Yb³⁺:Y₃Al₅O₁₂) laser ceramics doped by 5, 10 and 15 at% of ytterbium ions were obtained by reactive sintering. Optimal sintering temperature range for the formation of highly-dense transparent Yb³⁺:Y₃Al₅O₁₂ ceramics under normal recrystallization conditions was found to be T = 1750–1800 °C. The influence of Yb³⁺ ions on structural-phase state, phase composition, microstructure, optical and luminescent properties of sintered samples was experimentally investigated. It was shown that lattice parameter a of Yb³⁺:Y₃Al₅O₁₂ ceramics decreases linearly with increasing of Yb³⁺ concentration in a good agreement with L. Vegard’s rule, that indicates to the formation of (Y_1−xYb_x)₃Al₅O₁₂ (х = 0.05–0.15) substitutional solid solutions. No concentration quenching of Yb³⁺ luminescence was observed in Yb³⁺:Y₃Al₅O₁₂ within the 5–15 at% doping range. Quasi-CW lasing of Yb³⁺:Y₃Al₅O₁₂ ceramics was studied under diode-pumping at 970 nm. A highest slope efficiency of about 50% was obtained for 15 at%-doped Yb³⁺:Y₃Al₅O₁₂ ceramics sintered at T = 1800 °C for 10 h.     

Thermal expansion and mechanical properties of self-reinforced aluminum titanate ceramics with elongated grains

To fabricate aluminum titanate ceramics that possess both low thermal expansion coefficients and excellent mechanical properties, the co-doping of MgO with Y₂O₃, La₂O₃ and Nb₂O₅ was examined. Doping with MgO lowered the formation reaction temperature of aluminum titanate and prevented the formation of oriented grain regions. Liquid-phase sintering at 1500 °C of the MgO-La₂O₃-doped ceramic resulted in the formation of a minor amount of elongated grains with lengths of approximately 130 μm. This microstructure resulted in a high resistance against crack propagation during the bend test. Grain pull-out and grain bridging mechanisms as well as crack deflection and branching resulted in the high resistance. A low thermal expansion coefficient of 0.7 × 10⁻⁶/deg was observed for this ceramic. The co-doping of MgOY₂O₃ led to high bending strength and moderate low thermal expansion coefficient. The co-doping of MgO-Nb₂O₅ resulted in an extended grain growth by liquid-phase sintering at 1500 °C and poor mechanical properties.     

Pressureless Sintering of Al2O3/Ni Nanocomposites

In the present study, an Al₂O₃/Ni nanocomposite containing 5 vol% Ni is prepared by pressureless sintering at 1400°C for 2 h. Most nickel inclusions, around 70% in the sintered nanocomposite, locate at the intergranular sites, the triple junctions and Al₂O₃/Al₂O₃ grain boundaries. The average size of the nickel inclusions at the triple junctions, grain boundaries and intragranular locations is 145, 131 and 73 nm, respectively. The average size of all nickel inclusions is 118 nm. The presence of nickel inclusions can prohibit the grain growth of matrix grains. The size of Al₂O₃ grains in the sintered nanocomposite is only 490 nm. The strength of the nanocomposite is thus high for the refined microstructure. The matrix Al₂O₃ grains and Ni inclusions at triple junctions underwent considerable coarsening during a post-annealing treatment at 1300°C for 2 h. The strength of the annealed composites is thus reduced significantly after annealing.     

Low-temperature sintering behavior of the nano-sized AlN powder achieved by super-fine grinding mill with Y2O3 and CaO additives

For low-temperature sintering, mixtures of AlN powder doped with 3.53 mass% Y₂O₃ and 0–2.0 mass% CaO as sintering additives were pulverized and dispersed in a vertical super-fine grinding mill with very small ZrO₂ beads. The particle sizes achieved ranged between 50 and 100 nm after grinding for 90 min. The mixtures were then fired at 1000–1500 °C for 0–6 h under nitrogen gas pressure of 0.1 MPa. All nano-sized powders showed pronounced densification from 1300 °C as revealed by shrinkage measurement. The larger amounts of sintering additives enhanced AlN sintering at lower temperatures. Densified AlN ceramics with very fine and uniform grains of 0.3–0.4 μm were obtained at a firing temperature of 1500 °C for 6 h.     

Sintering of Yb3+:Y2O3 transparent ceramics in hydrogen atmosphere

Highly transparent Yb³⁺:Y₂O₃ ceramics with doping concentration up to 40.0 at.% had been fabricated successfully via hydrogen atmosphere sintering, where the raw powders were synthesized by co-precipitation method. The sintering temperature is about 600 °C lower than its melting temperature. SEM investigation revealed the average grain size of Yb³⁺:Y₂O₃ ceramics sintered at 1850 °C for 9 h was about 7 μm. The highest transmittance of as-prepared 1 mm thickness samples around wavelength of 1050 nm reached 80%, which is close to the theoretical value of Y₂O₃. The optical spectroscopic properties of Yb³⁺:Y₂O₃ transparent ceramics have also been investigated, which shows that it is a very good laser material for diode laser pumping and short pulse mode-locked laser.     

Sintering mechanisms of Yttria with different additives

The sintering behaviour of conventional yttria powder was investigated, with emphasis on the effect of sintering additives such as B₂O₃, YF₃, Al₂O₃, ZrO₂, and TiO₂, etc. at sintering temperatures from 1000 °C to 1600 °C. Powder shrinkage behaviour was analysed using a dilatometer. The powder sintering mechanisms were identified at different temperatures using powder isothermal shrinkage curves. This analysis showed that the sintering additives B₂O₃ and YF₃ could improve yttria sintering by changing the diffusion/sintering mechanisms at certain temperatures, while sintering additives TiO₂, Al₂O₃ and ZrO₂ appeared to retard the powder densification at temperatures around 1000 °C and are more suitable when used at temperatures in excess of 1300 °C. The powder with La₂O₃ added had the slowest densification rate throughout the test temperatures in this experiment and was also found to be more suitable when used at temperatures higher than 1550 °C.     

Annealing effect on dielectric property of AlN ceramics

Effects of slow-cooling at high temperatures and annealing at intermediate temperatures on dielectric loss tangent of AlN ceramics were explored. Y₂O₃ was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900 °C for 2 h in a nitrogen flow atmosphere. In succession to the sintering, AlN samples were slow-cooled at a rate of 1 °C/min from 1900 to 1750 °C and/or annealed at 970 °C for 4 h. Al₅Y₃O₁₂ was detected in the AlN ceramics obtained by the slow-cooling and AlYO₃ was found in the ceramics cooled at a rate of 30 °C/min. AlN ceramics with a relative density of 0.986 were obtained by the slow-cooling method. On the other hand, very low tan δ values between 2.6 and 4.6 × 10⁻⁴ were obtained when the AlN ceramics were annealed at 970 °C for 4 h.     

B6O materials with Al2O3/Y2O3 additives densified by FAST/SPS and HIP

Fully densified B₆O materials with Al₂O₃/Y₂O₃ sintering additives amounts systematically varied between 0 and 15 vol.% and Al₂O₃/(Al₂O₃ + Y₂O₃) molar ratios of 0.05–1 were prepared by FAST/SPS and HIP at sintering temperatures between 1725 °C and 1900 °C. Their densification and microstructure were correlated with measured mechanical properties. The addition of low additive amounts in the range of 2–3 vol.% was found to increase the fracture toughness and strength from 2.0 MPa m^1/2 (SEVNB) and 420 MPa for pure B₆O to about 3.0 MPa m^1/2 and 540 MPa, but it had no effect on the hardness, which remained at a high level of 30–36 GPa (HV_0.4). Higher additive contents did not yield a further improvement in the toughness but resulted in a reduction in hardness and strength.     

Densification of nanocrystalline Y2O3 ceramic powder by spark plasma sintering

Nanocrystalline Y₂O₃ powders with 18 nm crystallite size were sintered using spark plasma sintering (SPS) at different conditions between 1100 and 1600 °C. Dense specimens were fabricated at 100 MPa and 1400 °C for 5 min duration. A maximum in density was observed at 1400 °C. The grain size continuously increased with the SPS temperature into the micrometer size range. The maximum in density arises from competition between densification and grain growth. Retarded densification above 1400 °C is associated with enhanced grain growth that resulted in residual pores within the grains. Analysis of the grain growth kinetics resulted in activation energy of 150 kJ mol^?1 and associated diffusion coefficients higher by 10³ than expected for Y³⁺ grain boundary diffusion. The enhanced diffusion may be explained by combined surface diffusion and particle coarsening during the heating up with grain boundary diffusion at the SPS temperature.     

Characteristics of BaNd2Ti5O14 powders directly prepared by high-temperature spray pyrolysis

BaNd₂Ti₅O₁₄ powders were directly prepared by high-temperature spray pyrolysis. The powders prepared at temperatures of 1300 and 1500 °C exhibited a pure BaNd₂Ti₅O₁₄ phase. The powders prepared at 1300 °C were spherical in shape. However, the powders prepared at 1500 °C showed non-spherical shapes. The BaNd₂Ti₅O₁₄ powders had a composition similar to that of the spray solution. The mean sizes of the BaNd₂Ti₅O₁₄ powders increased from 0.23 to 0.60 μm when the concentration of the spray solution was increased from 0.01 to 0.2 M. At a sintering temperature of 1100 °C, bridge-like structures were formed between the powders. Pellets sintered at 1300 °C exhibited a dense structure comprising rod-like crystals.