Characterisation by TPR, XRD and NOx Storage Capacity Measurements of the Ageing by Thermal Treatment and SO2 Poisoning of a Pt/Ba/Al NOx-Trap Model Catalyst

The deactivation of a Pt/Ba/Al₂O₃ NO _x -trap model catalyst submitted to SO₂ treatment and/or thermal ageing at 800 °C was studied by H₂ temperature programmed reduction (TPR), X-ray diffraction (XRD) and NO _x storage capacity measurements.The X-ray diffractogram of the fresh sample exhibits peaks characteristic for barium carbonate. Thermal ageing leads to the decomposition of barium carbonate and to the formation of BaAl₂O₄. The TPR profile of the sulphated sample shows the presence of (i) surface aluminium sulphates, (ii) surface barium sulphates, (iii) bulk barium sulphates. The exposure to SO₂ after ageing leads to a small decrease of the surface barium-based sulphates, expected mainly as aluminate barium sulphates. This evolution can be attributed to a sintering of the storage material. TPR experiments also show that thermal treatment at 800 °C after the exposure to SO₂ involves the decomposition of aluminium surface sulphates to give mainly bulk barium sulphates, also pointed out by XRD. Thus, the thermal treatment at 800 °C leads to a stabilization of the sulphates.These results are in accordance with the NO _x storage capacity measurements. On non-sulphated catalysts, the treatment at 800 °C induces to a decrease of the NO _x storage capacity, showing that barium aluminate presents a lower NO _x storage capacity than barium carbonate. Sulphation strongly decreases the NO _x storage capacity of catalysts, whatever the initial thermal treatment, showing that barium sulphates inhibit the NO₂ adsorption. Moreover, the platinum activity for the NO to NO₂ oxidation is lowered by thermal treatments.     

Deterioration Mode of Barium-Containing NOx Storage Catalyst

Barium-containing NO _x storage catalyst showed serious deactivation under thermal exposure at high temperatures. To elucidate the thermal deterioration of the NO _x storage catalyst, four types of model catalyst, Pt/Al₂O₃, Ba/Al₂O₃, Pt–Ba/Al₂O₃, and a physical mixture of Pt/Al₂O₃ + Ba/Al₂O₃ were prepared and their physicochemical properties such as BET, NO TPD, TGA/DSC, XRD, and XPS were evaluated while the thermal aging temperature was increased from 550 to 1050°C. The fresh Pt–Ba/Al₂O₃ showed a sorption capacity of 3.35 wt%/g-cat. but the aged one revealed a reduced capacity of 2.28 wt%/g-cat. corresponding to 68% of the fresh one. It was found that this reduced sorption capacity was directly related to the deterioration of the NO _x storage catalyst by thermal aging. The Ba on Ba/Al₂O₃ and Pt–Ba/Al₂O₃ catalysts began to interact with alumina to form Ba–Al solid alloy above 600°C and then transformed into stable BaAl₂O₄ having a spinel structure. However, no phase transition was observed in the Pt/Al₂O₃ catalyst having no barium component, even after aging at 1050°C.     

Role of cobalt on γ-Al2O3 based NO x storage catalyst

Co/Pt/Ba/γ-Al₂O₃, Co/Ba/γ-Al₂O₃, Pt/Ba/γ-Al₂O₃, Co/Pt/γ-Al₂O₃, Ba/γ-Al₂O₃, Pt/γ-Al₂O₃, and Co/γ-Al₂O₃ type catalysts were prepared by a conventional impregnation method, and their NO _x storage capacities were evaluated by colorimetric assay. Co-containing catalysts had a higher NO _x storage capacity than that of Co-free counterparts. The role of each component, especially Co, for the catalysts prepared was investigated by using in-situ FTIR. The high NO _x storage for Co-containing catalysts including Co/Ba/γ-Al₂O₃ and Co/Pt/Ba/γ-Al₂O₃ is mainly due to the formation of Co₃O₄ on the catalyst surface identified by XAFS.     

Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

Influence of the Storage Material on the Storage of NOx at Low Temperatures

The NO _x storage performance at low temperature (100–200 °C) has been studied for model NO _x storage catalysts. The catalysts were prepared by sequentially depositing support, metal oxide and platinum on ceramic monoliths. The support material consisted of acidic aluminium silicate, alumina or basic aluminium magnesium oxide, and the added metal oxide was either ceria or barium oxide. The NO _x conversion was evaluated under net-oxidising conditions with transients between lean and rich gas composition and the NO _x storage performance was studied by isothermal adsorption of NO₂ followed by temperature programmed desorption of adsorbed species. The maximum in NO _x storage capacity was observed at 100 °C for all samples studied. The Pt/BaO/Al₂O₃ catalyst stored about twice the amount of NO _x compared with the Pt/Al₂O₃ and Pt/CeO₂/Al₂O₃ samples. The storage capacity increased with increasing basicity of the support material, i.e. Pt/Al₂O₃·SiO₂ < Pt/Al₂O₃ < Pt/Al₂O₃ · MgO. Water did not significantly affect the NO _x storage performance for Pt/Al₂O₃ or Pt/BaO/Al₂O₃.     

Fundamental studies of NOx storage at low temperatures

A commercial NO_x storage catalyst (Pt, BaO and alumina containing) was investigated by temperature programmed desorption (TPD) experiments in the temperature range 100–400 °C. The catalyst stored a substantial amount of NO_x at 100 °C using NO + O₂. Nitrites or loosely bound NO species are suggested for this storage, since no NO was oxidised at this low temperature. In addition, the released NO_x during the temperature ramp consisted of mainly NO and at lower temperatures the NO₂ dissociation is limited. Water and CO₂ was found to decrease the storage substantially, 92% for the NO + O₂ adsorption at 100 °C. The total storage for 60 min using NO₂ + O₂ at 200 °C was similar when introducing CO₂ and H₂O. However, the initial total uptake of NO_x was decreased. Initially we probably formed loosely bound NO_x species, which likely are strongly influenced by water and CO₂. After longer time periods are barium nitrates probably formed and they can remove the carbonates by forming stable nitrates, thus resulting in the same total uptake of NO_x.     

CO2 effect on activity and stability of NOx storage reduction catalysts

A catalyst for NO_x storage/reduction was prepared to improve the activity of Ba–Pt/γ-Al₂O₃ by replacing Ba with a mixture of Ba and Mg. The catalyst was prepared by impregnating Pt and then co-impregnating Ba and Mg (Mg:Ba molar ratio = 1) on commercial γ-Al₂O₃. The tests have been carried out in the presence of CO₂ at temperatures between 200 and 400 °C in order to understand the role of both the feed and various alkaline-earth metals. The storage capacity of the two catalysts was different like the mechanism in the reduction process.     

Transient Surface Processes of Storage and Conversion of NOx Species on Pt–Me/Al2O3 Catalysts (Me = Ba,Ce, Cu)

The transient reactivity and surface phenomena of storage and conversion of NO _x species on Pt(1%)–Me/Al₂O₃ catalysts, where Me = Ba, Ce and Cu, were studied by the RWF (rectangular wavefront) method. The Me component has a relevant influence on the processes of surface storage and transformation. The reduction of NO _x by propene in the presence of oxygen is promoted by adding Cu to a Pt/Al₂O₃ catalyst, while cerium promotes transient conversion of NO in the absence of propene, but inhibits the reduction of NO _x in the presence of propene. Copper is suggested to be a promising element to add together with Ba for new NO _x storage-reduction catalysts due to its capacity to act both as a storage element and as promoter for NO _x reduction.     

FT-IR study of NO X storage mechanism over Pt/BaO/Al2O3 catalysts. Effect of the Pt–BaO interaction

NO _x storage mechanism over a model NSR catalyst has been analysed by means of in-situ FTIR. The results indicated that a two-step mechanism involving nitrite formation, without requirement of NO evolution to NO₂, followed by oxidation to nitrate species, being both steps assisted by O₂, would describe the overall process at 350 °C. This mechanism could be also extended to a wider temperature range. The interaction between Pt and Ba sites was crucial in this mechanism, since spillover process of oxidising agents appeared to play a key role. NO₂ direct interaction with BaO surface may also occur, but this process was only dominant on Ba sites away from Pt interaction.     

NOx Storage and Reduction Catalysts for Automotive Lean-Burn Engines: Effect of Parameters and Storage Materials on NOx Conversion

The effect of various parameters on the NO _x conversion over NO _x storage and reduction catalysts supported on alumina was investigated. The Pt/BaO/Al₂O₃ catalyst exhibited a higher NO _x reduction activity than the Pt/Al₂O₃ catalyst under the static and cycling conditions. The activity of Pt/BaO/Al₂O₃ catalyst was improved in the cycled feedstream. The Pt/SrO/Al₂O₃ was found to have as high activity as Pt/BaO/Al₂O₃ for NO _x reduction. In order to achieve effective reduction of NO _x , NO _x storage in the form of Me(NO₃)₂ (Me = Ba or Sr) is more favorable than other nitrates and the rich condition should be chosen in such a way that the sorption capacity can be fully regenerated at a fast rate and the inhibition effect by strongly adsorbed molecules derived from C₃H₆ and CO can be minimized.     

Role and distribution of different Ba-containing phases in supported Pt–Ba NSR catalysts

Pt–Ba/MeO (where MeO = Al₂O₃, CeO₂, SiO₂ and ZrO₂) NO _x storage-reduction catalysts with Ba-loading varying from 0 wt.% to 28 wt.% were investigated concerning stability of Ba phases and NO _x storage-reduction efficiency. For Pt–Ba/Al₂O₃ three different Ba-containing phases with different thermal stability are distinguished based on their interaction with the support. The relative concentration of these phases varies with the Ba-loading and NO _x storage tests indicated that the BaCO₃ phase decomposing between 400 °C and 800 °C (LT-BaCO₃) is the most efficient Ba containing phase for NO _x storage. Similar investigations of Pt–Ba catalysts supported on CeO₂, SiO₂ and ZrO₂ showed that the relative amount of LT-BaCO₃ phase depends also on the support material. NO _x storage measurements confirmed a correlation between the concentration of LT-BaCO₃ and NO _x storage efficiency. Basicity and textural properties of the support are identified as crucial parameters for efficient NO _x storage catalysts.     

Fundamental Investigations of Thermal Aging Phenomena of Model NOx Storage Systems

Investigations of the aging behavior induced by high temperatures coupled with oxidizing atmosphere of model NO _x storage systems Ba/Al₂O₃ and Ba/CeO₂ are reported in this paper. The samples were prepared, calcined and exposed to temperatures between 500 and 1000 °C in air for 12 h for thermal aging. Samples were characterized with XRD, HRSEM, DSC-TGA-MS and BET analyses. In XRD investigations of all model systems calcined at 500 °C for 2 h, the NO _x storage component was present in form of BaCO₃. The release of CO₂ as a result of the decarbonization of the NO _x storage component at increased temperatures was verified by thermogravimetric investigations. In the case of Ba/Al₂O₃, already during calcination a partial reaction of the NO _x storage component with Al₂O₃ resulting in the formation of barium aluminate was observed. In the model system Ba/CeO₂ the decomposition of the barium carbonate started above 780 °C and the formation of a barium cerium mixed oxide was observed. The presence of the barium containing NO _x storage component has a strong influence on the specific surface area of the model NO _x storage systems. The morphology and crystallite size of CeO₂ modified with the barium containing NO _x storage component exhibited distinct changes compared to the unmodified oxide. The NO _x storage efficiency determined by model gas tests of freshly prepared and engine aged model NO _x storage catalysts correlates well with the above described observations.     

NO x uptake mechanism on Pt/BaO/Al2O3 catalysts

The NO _x adsorption mechanism on Pt/BaO/Al₂O₃ catalysts was investigated by performing NO _x storage/reduction cycles, NO₂ adsorption and NO + O₂ adsorption on 2%Pt/(x)BaO/Al₂O₃ (x = 2, 8, and 20 wt%) catalysts. NO _x uptake profiles on 2%\Pt/20%BaO/Al₂O₃ at 523 K show complete uptake behavior for almost 5 min, and then the NO _x level starts gradually increasing with time and it reaches 75% of the inlet NO _x concentration after 30 min time-on-stream. Although this catalyst shows fairly high NO _x conversion at 523 K, only ~2.4 wt% out of 20 wt% BaO is converted to Ba(NO₃)₂. Adsorption studies by using NO₂ and NO + O₂ suggest two different NO _x adsorption mechanisms. The NO₂ uptake profile on 2%Pt/20%BaO/Al₂O₃ shows the absence of a complete NO _x uptake period at the beginning of adsorption and the overall NO _x uptake is controlled by the gas–solid equilibrium between NO₂ and BaO/Ba(NO₃)₂ phase. When we use NO + O₂, complete initial NO _x uptake occurs and the time it takes to convert ~4% of BaO to Ba(NO₃)₂ is independent of the NO concentration. These NO _x uptake characteristics suggest that the NO + O₂ reaction on the surface of Pt particles produces NO₂ that is subsequently transferred to the neighboring BaO phase by spill over. At the beginning of the NO _x uptake, this spill-over process is very fast and so it is able to provide complete NO _x storage. However, the NO _x uptake by this mechanism slows down as BaO in the vicinity of Pt particles are converted to Ba(NO₃)₂. The formation of Ba(NO₃)₂ around the Pt particles results in the development of a diffusion barrier for NO₂, and increases the probability of NO₂ desorption and consequently, the beginning of NO _x slip. As NO _x uptake by NO₂ spill-over mechanism slows down due to the diffusion barrier formation, the rate and extent of NO₂ uptake are determined by the diffusion rate of nitrate ions into the BaO bulk, which, in turn, is determined by the gas phase NO₂ concentration.     

Perovskite-Based Lean-Burn NOx Trap Catalysts Without Using Platinum Group Metals: K/LaCoO3/Ce1?xZrxO2

Abstract  

A series of Ce_1−x Zr _x O₂ (x = 0, 0.1, 0.2, 0.3) solid solution supported lean-burn NO _x trap (LNT) catalysts K/LaCoO₃/Ce_1−x Zr _x O₂ were prepared by successive impregnation. After sulfation the supported perovsikte LaCoO₃ was well maintained; reducing treatment partly destroyed the perovsikte, but it can be well recovered by re-oxidation treatment. Based on NO _x storage and sulfur-resisting performance of the catalysts, the optimal atomic ratio of Zr in Ce_1−x Zr _x O₂ support is x = 0.2. The catalyst K/LaCoO₃/Ce_0.8Zr_0.2O₂ exhibits much better NO _x storage capacity than the Pt-based catalyst Pt/K/Ce_0.8Zr_0.2O₂, which is highly related to its stronger capability for NO to NO₂ oxidation. During NO _x storage much larger amounts of nitrate and nitrite species were identified by in situ DRIFTS over perovskite-based catalysts than over Pt-based one. The H₂-TPR results reveal that after deep sulfation little sulfur species were deposited on the catalyst K/LaCoO₃/Ce_1−x Zr _x O₂, showing strong sulfur-resisting ability. As a result, it is thought that the full replacement of Pt by perovskite LaCoO₃ in the corresponding LNT catalysts is feasible.     

Performance of potassium-promoted catalysts for NO x and soot removal from simulated diesel exhaust

In order to elucidate the effect of support in the catalytic performance, two selected potassium-promoted catalysts (K1Cu/beta and KCu2/Al₂O₃) were tested for the simultaneous NO _x /soot removal from a simulated diesel exhaust. For comparative purpose, the behaviour of a platinum catalyst (Pt/beta) was also studied. Isothermal experiments revealed that the potassium-promoted catalysts show a high activity for NO _x /soot removal in the 350–450 °C temperature range. In addition, the catalysts present the advantage that the main reaction products are N₂ and CO₂. Among the catalysts tested, KCu2/Al₂O₃ presents the best global performance at 450 °C: the highest soot consumption rate, even higher than the platinum catalysts, and a high NO _x reduction.     

Model Studies of NOx Storage and Sulphur Deactivation of NOx Storage Catalysts

The storage of NO _x under lean conditions in model NO _x storage catalysts as well as the deactivation by sulphur have been studied. We find that NO₂ plays an important role in the storage mechanism as an oxidising agent. Two different mechanisms for this are discussed: the formation of surface peroxides and the oxidation of nitrites to nitrates. FTIR studies show that NO _x is stored as surface nitrates. The sulphur deactivation is found to be more severe when SO₂ is added during the rich phase than when SO₂ is added during the lean period. FTIR shows the formation of bulk sulphates both under lean and rich conditions.     

Thermal ageing phenomena and strategies towards reactivation of NO x - storage catalysts

The thermal ageing and reactivation of Ba/CeO₂ and Ba/Al₂O₃ based NO _x -storage/ reduction (NSR) catalysts was studied on model catalysts and catalyst systems at the engine. The mixed oxides BaAl₂O₄ and BaCeO₃, which lower the storage activity, are formed during ageing above 850 °C and 900 °C, respectively. Interestingly, the decomposition of BaCeO₃ in an atmosphere containing H₂O/NO₂ leads again to NO _x -storage active species, as evidenced by comparison of fresh, aged and reactivated Pt-Ba/CeO₂ based model catalysts. This can be technically exploited, particularly for the Ba/CeO₂ catalysts, as reactivation studies on thermally aged Ba/CeO₂ and Ba/Al₂O₃ based NSR catalysts on an engine bench showed. An on-board reactivation procedure is presented, that improved the performance of a thermally aged catalyst significantly.     

Mechanistic Investigation of Co Containing NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Traps

Co-containing NO _x storage and reduction catalysts were investigated to identify the mechanism of Co promotion. X-ray diffraction and temperature programmed reduction demonstrated that Co exists in a highly oxidized state (Co₃O₄) and that the surface oxygen could be removed from the catalyst a typical operating conditions around 300 °C. Electron microscopy showed that Co is more uniformly distributed over the catalyst surface, as compared to Pt, with particle sizes ranging between 20 and 80 nm. In situ IR studies illustrated that NO _x storage occurs on Co-containing NSR catalyst via formation of nitrites and nitrates as surface intermediates. Finally, it was found that, similar to Pt, the addition of Co to Ba catalysts enhances the nitrite to nitrate transition rate and also increases the overall formation of nitrates. Therefore, the promotional effect shown by Co is the result of the combination of increased NO to NO₂ oxidation and improved surface area for NO₂ spillover to the Ba storage sites.     

Steam effect on NO x reduction over lean NO x trap Pt–BaO/Al2O3 model catalyst

The effect of steam on NO _x reduction over lean NO _x trap (LNT) Pt–Ba/Al₂O₃ and Pt/Al₂O₃ model catalysts was investigated with reaction protocols of rich steady-state followed by lean–rich cyclic operations using CO and C₃H₈ as reductants, respectively. Compared to dry atmosphere, steam promoted NO _x reduction; however, under rich conditions the primary reduction product was NH₃. The results of NO _x reduction and NH₃ selectivity versus temperature, combined with temperature programmed reduction of stored NO _x over Pt–BaO/Al₂O₃ suggest that steam causes NH₃ formation over Pt sites via reduction of NO _x by hydrogen that is generated via water gas shift for CO/steam, or via steam reforming for C₃H₈/steam. During the rich mode of lean–rich cyclic operation with lean–rich duration ratio of 60 /20 s, not only the feed NO, but also the stored NO _x contributed to NH₃ formation. The NH₃ formed under these conditions could be effectively trapped by a downstream bed of Co²⁺ exchanged Beta zeolite. When the cyclic operation was switched into lean mode at T < 450 °C, the trapped ammonia in turn participated in additional NO _x reduction, leading to improved NO _x storage efficiency.     

Influence of the storage material on the storage of NO x at low temperatures

The NO _x storage performance at low temperature (100–200 °C) has been studied for model NO _x storage catalysts. The catalysts were prepared by sequentially depositing support, metal oxide and platinum on ceramic monoliths. The support material consisted of acidic aluminium silicate, alumina or basic aluminium magnesium oxide, and the added metal oxide was either ceria or barium oxide. The NO _x conversion was evaluated under net-oxidising conditions with transients between lean and rich gas composition and the NO _x storage performance was studied by isothermal adsorption of NO₂ followed by temperature programmed desorption of adsorbed species. The maximum in NO _x storage capacity was observed at 100 °C for all samples studied. The Pt/BaO/Al₂O₃ catalyst stored about twice the amount of NO _x compared with the Pt/Al₂O₃ and Pt/CeO₂/Al₂O₃ samples. The storage capacity increased with increasing basicity of the support material, i.e. Pt/Al₂O₃ · SiO₂ < Pt/Al₂O₃ < Pt/Al₂O₃ · MgO. Water did not significantly affect the NO _x storage performance for Pt/Al₂O₃ or Pt/BaO/Al₂O₃.