Performance and combustion characteristics of biodiesel–diesel–methanol blend fuelled engine

An experimental investigation was conducted to evaluate the effects of using methanol as additive to biodiesel–diesel blends on the engine performance, emissions and combustion characteristics of a direct injection diesel engine under variable operating conditions. BD50 (50% biodiesel and 50% diesel in vol.) was prepared as the baseline fuel. Methanol was added to BD50 as an additive by volume percent of 5% and 10% (denoted as BDM5 and BDM10). The results indicate that the combustion starts later for BDM5 and BDM10 than for BD50 at low engine load, but is almost identical at high engine load. At low engine load of 1500 r/min, BDM5 and BDM10 show the similar peak cylinder pressure and peak of pressure rise rate to BD50, and higher peak of heat release rate than that of BD50. At low engine load of 1800 r/min, the peak cylinder pressure and the peak of pressure rise rate of BDM5 and BDM10 are lower than those of BD50, and the peak of heat release rate is similar to that of BD50. The crank angles at which the peak values occur are later for BDM5 and BDM10 than for BD50. At high engine load, the peak cylinder pressure, the peak of pressure rise rate and peak of heat release rate of BDM5 and BDM10 are higher than those of BD50, and the crank angle of peak values for all tested fuels are almost same. The power and torque outputs of BDM5 and BDM10 are slightly lower than those of BD50. BDM5 and BDM10 show dramatic reduction of smoke emissions. CO emissions are slightly lower, and NO_x and HC emissions are almost similar to those of BD50 at speed characteristic of full engine load.     

Performance and emission characteristics of a diesel engine using isobutanol–diesel fuel blends

The aim of this study is to investigate the suitability of isobutanol–diesel fuel blends as an alternative fuel for the diesel engine, and experimentally determine their effects on the engine performance and exhaust emissions, namely break power, break specific fuel consumption (BSFC), break thermal efficiency (BTE) and emissions of CO, HC and NO_x. For this purpose, four different isobutanol–diesel fuel blends containing 5, 10, 15 and 20% isobutanol were prepared in volume basis and tested in a naturally aspirated four stroke direct injection diesel engine at full -load conditions at the speeds between 1200 and 2800 rpm with intervals of 200 rpm. The results obtained with the blends were compared to those with the diesel fuel as baseline. The test results indicate that the break power slightly decreases with the blends containing up to 10% isobutanol, whereas it significantly decreases with the blends containing 15 and 20% isobutanol. There is an increase in the BSFC in proportional to the isobutanol content in the blends. Although diesel fuel yields the highest BTE, the blend containing 10% isobutanol results in a slight improvement in BTE at high engine speeds. The results also reveal that, compared to diesel fuel, CO and NO_x emissions decrease with the use of the blends, while HC emissions increase considerably.     

Evaluation of vibration characteristics of a hydroxyl (HHO) gas generator installed diesel engine fuelled with different diesel–biodiesel blends

There are two main reasons of alternative fuel search of scientists: environmental problems resulted from combustion of fossil fuels and limited reserves of crude oil. Biodiesel and Hydrogen (H₂) are two of the most promising alternative fuels with their environmental friendly combustion profiles. The aim of this study was to evaluate vibration level of a hydroxyl (HHO) gas generator installed and diesel engine using different kinds of biodiesel fuels. In this study, at different flow rates, the effect of HHO gas addition on engine vibration performance was investigated with a Mitsubishi Canter 4D34-2A diesel engine. HHO gas introduced to the test engine via its intake manifold with 2, 4 and 6 L per minute (LPM) flow rates when the engine was fuelled with sunflower, canola, and corn biodiesels. The vibration data was collected between 1200 and 2400 rpm engine speeds by 300 rpm intervals. Finally, artificial neural network (ANN) approach was conducted in order to predict the effect of fuel properties and HHO amount on engine vibration level.     

Experimental investigation on the performance and emissions of a diesel engine fuelled with ethanol–diesel blends

An experimental investigation on the application of the blends of ethanol with diesel to a diesel engine was carried out. First, the solubility of ethanol and diesel was conducted with and without the additive of normal butanol (n-butanol). Furthermore, experimental tests were carried out to study the performance and emissions of the engine fuelled with the blends compared with those fuelled by diesel. The test results show that it is feasible and applicable for the blends with n-butanol to replace pure diesel as the fuel for diesel engine; the thermal efficiencies of the engine fuelled by the blends were comparable with that fuelled by diesel, with some increase of fuel consumptions, which is due to the lower heating value of ethanol. The characteristics of the emissions were also studied. Fuelled by the blends, it is found that the smoke emissions from the engine fuelled by the blends were all lower than that fuelled by diesel; the carbon monoxide (CO) were reduced when the engine ran at and above its half loads, but were increased at low loads and low speed; the hydrocarbon (HC) emissions were all higher except for the top loads at high speed; the nitrogen oxides (NO_x) emissions were different for different speeds, loads and blends.     

Theoretical and experimental study on the performance of a diesel engine fueled with diesel–biodiesel blends

This study reports the effects of engine load and biodiesel percentage on the performance of a diesel engine fueled with diesel–biodiesel blends by experiments and a new theoretical model based on the finite-time thermodynamics (FTT). In recent years, biodiesel utilization in diesel engines has been popular due to depletion of petroleum-based diesel fuel. In this study, performance of a single cylinder, four-stroke, direct injection (DI) diesel engine fueled with diesel–biodiesel mixtures has been experimentally and theoretically investigated. The simulation results agree with the experimental data. After model validation, the effects of engine load and biodiesel percentage on engine performance have been parametrically investigated. The results showed that, effective power increases constantly, effective efficiency increases to a specified value and then starts to decrease with increasing engine load at constant biodiesel percentage and compression ratio. However, effective efficiency increases, effective power decreases to a certain value and then begins to increase with increasing biodiesel percentage at constant equivalence ratio and compression ratio.     

Performance and emission characteristics of a diesel engine fueled with coconut oil–diesel fuel blend

The objective of the present study is to reveal the effects of pure coconut oil and coconut oil–diesel fuel blends on the performance and emissions of a direct injection diesel engine. Operation of the test engine with pure coconut oil and coconut oil–diesel fuel blends for a wide range of engine load conditions was shown to be successful even without engine modifications. It was also shown that increasing the amount of coconut oil in the coconut oil–diesel fuel blend resulted in lower smoke and NO_x emissions. However, this resulted in an increase in the BSFC. This was attributed to the lower heating value of neat coconut oil fuel compared to diesel fuel.     

Experimental investigation on performance and emission characteristics of waste tire pyrolysis oil–diesel blends in a diesel engine

Disposal of waste tires is one of the most important problems that should be solved. This problem can be solved by considering waste tires for production of hydrogen or fuel for diesel engines. This paper presents the studies on the performance and emission characteristics of a four stroke, four cylinders, naturally aspirated, direct-injected diesel engine running with various blends of waste tire pyrolysis oil (WTPO) with diesel fuel. Fuel properties, engine performance, and exhaust emissions of WTPO and its blends were analyzed and compared with those of petroleum diesel fuel. The experimental results showed that WTPO–diesel blends indicated similar performance with diesel fuel in terms of torque and power output of the test engine. It was found that the blends of pyrolysis oil of waste tire WTPO10 can efficiently be used in diesel engines without any engine modifications.     

Performance,emission and combustion characteristic of a multicylinder DI diesel engine running on diesel–ethanol–biodiesel blends of high ethanol content

Feasibility of using high percentage of ethanol in diesel–ethanol blends, with biodiesel as a co-solvent and properties enhancer has been investigated. The blends tested are D70/E20/B10 (blend A), D50/E30/B20 (blend B) D50/E40/B10 (blend C), and Diesel (D100). The blends are prepared to get maximum percentage of oxygen content but keeping important properties such as density, viscosity and Cetane index within acceptable limits. Experiments are conducted on a multicylinder, DI diesel engine, whose original injection timing was 13° CA BTDC. The engine did not run on blends B and C at this injection timing and it was required to advance timing to 18° and 21° CA BTDC to enable the use of blends B and C respectively. However advancing injection timing almost doubled the NO emissions and increased peak firing pressure. The P–θ and net heat release diagrams shows that the combustion process of these blends delayed at low loads but approaches to the diesel fuel at high loads. The comparison of blend results with baseline diesel showed that brake specific fuel consumption increased considerably, thermal efficiency improved slightly, smoke opacity reduced remarkably at high loads. NO variation depends on operating conditions while CO emissions drastically increased at low loads. Blend B which replaced 50% diesel and having oxygen content up to 12.21% by weight has given satisfactory performance for steady state running mode up to 1600 RPM however, it does not showed any benefit on peak smoke emission during free acceleration test.     

The experimental study on the performance,combustion and emission characteristics of a diesel engine using diesel – biodiesel – diethyl ether blends

ABSTRACT

In the present research work, the experimental analysis has been executed to investigate the influence of diethyl ether as an oxygenated additive to the diesel-biodiesel blend on the performance, combustion and emission characteristics of a diesel engine. The biodiesel (Frying oil methyl ester) was prepared by the transesterification process, and the biodiesel was added (40% by volume) to the diesel fuel to prepare the diesel-biodiesel blend (D60FME40). The diethyl ether was added to the diesel-biodiesel blends D60FM35 (diesel 60% + biodiesel 35% by volume) and D60FM30 (diesel 60% + biodiesel 30% by volume) with suitable volume proportions of 5% and 10% respectively to form diesel-biodiesel-diethyl ether blends ((D60FM35DEE5) & (D60FM30DEE10)). Initially, the test was conducted with diesel fuel to obtain the baseline reference reading. Then, the reading was compared with results taken from the engine using a diesel-biodiesel blend (D60FME40) and diethyl ether blends (D60FM35DEE5) & (D60FM30DEE10). The results reveal that the maximum brake thermal efficiency was obtained with diesel fuel and it was higher than the diesel-biodiesel blend and diethyl ether blends. The peak in-cylinder gas pressure and heat release rate in the premixed stage was less for the diesel-biodiesel blend, but it was increased with the addition of diethyl ether to the blend. The diesel-biodiesel-diethyl ether blends show less carbon monoxide and hydrocarbon emissions except for NO_X emission as compared to the diesel and diesel-biodiesel blend, especially at the engine rated power.     

Investigation of combustion and emission characteristics in a TBC diesel engine fuelled with CH4–CO2–H2 mixtures

In this study, an experimental investigation was performed to reveal combustion and emission characteristics of common-rail four-cylinder diesel engine run with CH₄, CO₂ and H₂ mixtures. The engine pistons were thermally coated with zirconia and Ni–Al bond coat by plasma spray method. With a small amount of the pilot diesel, port fuelled methane (100% CH₄), synthetic biogas (80% CH₄ + 20% CO₂), and hydrogen presented (80% CH₄+10% CO₂+10% H₂) mixtures were used as main fuel at different loads (50 Nm, 75 Nm, and 100 Nm) at a constant speed of 1750 min^?1. Comparative analysis of the combustion (cylinder pressure, PRR, HRR, CHR, ringing intensity, CA10, CA50, and CA90), BSFC, and emissions (CO₂, HC, NO_x, smoke, and oxygen) at the various engine loads with and without piston coating was made for all fuel combinations. It was found that coating the engine pistons enhanced the examining combustion characteristics, whereas it slightly changed BSFC and most of the emissions. As compared to the sole diesel fuel, the gaseous fuel operations showed higher in-cylinder pressure, PRR, and ringing intensity values, earlier combustion starting and CAs, and lower diesel injection pressure at the same engine operating conditions. Dramatic increase in the ringing intensity was particularly found by the hydrogen introduced mixture under the tests with coated piston. HC and CO₂ emissions increased in operation with the synthetic biogas; however, hydrogen introduction reduced HC emissions by 4.97–30.92%, and CO₂ emissions by 5.16–10%.     

Combustion,emission and engine performance characteristics of used cooking oil biodiesel—A review

As the environment degrades at an alarming rate, there have been steady calls by most governments following international energy policies for the use of biofuels. One of the biofuels whose use is rapidly expanding is biodiesel. One of the economical sources for biodiesel production which doubles in the reduction of liquid waste and the subsequent burden of sewage treatment is used cooking oil (UCO). However, the products formed during frying, such as free fatty acid and some polymerized triglycerides, can affect the transesterification reaction and the biodiesel properties. This paper attempts to collect and analyze published works mainly in scientific journals about the engine performance, combustion and emissions characteristics of UCO biodiesel on diesel engine. Overall, the engine performance of the UCO biodiesel and its blends was only marginally poorer compared to diesel. From the standpoint of emissions, NOx emissions were slightly higher while un-burnt hydrocarbon (UBHC) emissions were lower for UCO biodiesel when compares to diesel fuel. There were no noticeable differences between UCO biodiesel and fresh oil biodiesel as their engine performances, combustion and emissions characteristics bear a close resemblance. This is probably more closely related to the oxygenated nature of biodiesel which is almost constant for every biodiesel (biodiesel has some level of oxygen bound to its chemical structure) and also to its higher viscosity and lower calorific value, which have a major bearing on spray formation and initial combustion.     

Investigation of combustion characteristics and emissions in a spark-ignition engine fuelled with natural gas–hydrogen blends

In this study, an experimental study on the performance and exhaust emissions of a spark-ignition engine fuelled with methane–hydrogen mixtures (100% CH₄, 10% H₂ + 90% CH₄, 20% H₂ + 80% CH₄, and 30% H₂ + 70% CH₄) were performed at different engine speeds and different excessive air ratios. This present work was carried out on a Ford engine. This is a four-stroke cycle four-cylinder spark-ignition engine with a bore of 80.6 mm, a stroke of 88 mm and a compression ratio of 10:1. Experiments were performed at 1500, 2000, 2500 and 3000 rpm and at wide open throttle (WOT). CO, CO₂ and HC emission values and cylinder pressure were measured. The results showed that while the speed and excessive air ratio increase, CO emission values decrease. The reduction of HC and CO emissions could be obtained by adding hydrogen into the natural gas when operating on the lean mixture condition. Increasing the excessive air ratio also decreases the maximum peak cylinder pressure.     

An experimental study on performance and emission characteristics of a methane–hydrogen fuelled gasoline engine

In this paper, the performance and emission characteristics of a conventional twin-cylinder, four stroke, spark-ignited (SI) engine that is running with methane–hydrogen blends have been investigated experimentally. The engine was modified to realize hydrogen port injection by installing hydrogen feeding line in the intake manifolds. The experimental results have been demonstrated that the brake specific fuel consumption (BSFC) increased with the increase of hydrogen fraction in fuel blends at low speeds. On the other hand, as hydrogen percentage in the mixture increased, BSFC values decreased at high speeds. Furthermore, brake thermal efficiencies were found to decrease with the increase in percentage of hydrogen added. In addition, it has been found that CO₂, NO_x and HC emissions decrease with increasing hydrogen. However, CO emissions tended to increase with the addition of hydrogen generally increase. It has been showed that hydrogen is a very good choice as a gasoline engine fuel. The data are also very useful for operational changes needed to optimize the hydrogen fuelled SI engine design.     

Modeling and prediction of NOx emission in an LPG–diesel dual-fuel CI engine

Different alternative fuels have been proposed by various researchers in diesel engines in view of increased NO_x and particulate emissions. Out of the various methods proposed, dual fueling is one of the most important techniques that helps solve the different operational problems related to diesel engine combustion and emission. In the current study, modeling and predicting the formation of NO_x emission in a duel fuel liquefied petroleum gas (LPG)–diesel engine has been undertaken. Simulations have been conducted for various LPG flow rates at different engine loads and the predicted NO_x values are compared with the experimental values. The results found that there is a decent agreement between the forecasted and the investigational results, where the average difference is within 13.7%. Furthermore, it is found that minimum NO_x emission was observed for an LPG flow rate in the range of 0.4–0.6 kg/h and when the engine is running with 75% loading.     

Investigation on the effect of injection system parameters on performance and emission characteristics of a twin cylinder compression ignition direct injection engine fuelled with pongamia biodiesel–diesel blend using response surface methodology

This study is aimed at investigating the effect of injection system parameters such as injection pressure, injection timing and nozzle tip protrusion on the performance and emission characteristics of a twin cylinder water cooled naturally aspirated CIDI engine. Biodiesel, derived from pongamia seeds through transesterification process, blended with diesel was used as fuel in this work. The experiments were designed using a statistical tool known as Design of Experiments (DoE) based on response surface methodology (RSM). The resultant models of the response surface methodology were helpful to predict the response parameters such as Brake Specific Energy Consumption (BSEC), Brake Thermal Efficiency (BTE), Carbon monoxide (CO), Hydrocarbon (HC), smoke opacity and Nitrogen Oxides (NO_x) and further to identify the significant interactions between the input factors on the responses. The results depicted that the BSEC, CO, HC and smoke opacity were lesser, and BTE and NO_x were higher at 2.5 mm nozzle tip protrusion, 225 bar of injection pressure and at 30° BTDC of injection timing. Optimization of injection system parameters was performed using the desirability approach of the response surface methodology for better performance and lower NO_x emission. An injection pressure of 225 bar, injection timing of 21° BTDC and 2.5 mm nozzle tip protrusion were found to be optimal values for the pongamia biodiesel blended diesel fuel operation in the test engine of 7.5 kW at 1500 rpm.     

Analysis of blended fuel properties and engine performance with palm biodiesel–diesel blended fuel

Depleting fossil fuel sources accompanied by continuously growing energy demands lead to increased interest in alternative energy sources. Blended biodiesel–diesel fuel has been approved as a commercial fuel at a low blending ratio. However, problems related to fuel properties are persistent at high blending ratios. Hence, in this study, the feasibility of biodiesel produced from palm oil was investigated. Characterization of blended fuel properties with increasing palm biodiesel ratio is conducted to evaluate engine performance test results. The qualifying of blended fuel properties was used to indicate the maximum blending ratio suitable for use in unmodified diesel engines according to the blended fuel standard ASTM D7467. The property test results revealed that blended fuel properties meet blended fuel standard requirements at up to 30% palm oil biodiesel. Furthermore, blending is efficient for reduction of the pour point from 14 °C for unblended biodiesel to less than 0 °C at a 30% biodiesel blending ratio. However, the energy content reduces by about 1.42% for each 10% increment of biodiesel. Engine test results demonstrated that there was no statistically significant difference for engine brake thermal efficiency among tested blended fuels compared to mineral diesel, and the lowest engine cyclic variation was achieved with blended fuel B30.     

Performance and emission evaluation of a CI engine fueled with preheated raw rapeseed oil (RRO)–diesel blends

Many studies are still being carried out to find out surplus information about how vegetable based oils can efficiently be used in compression ignition engines. Raw rapeseed oil (RRO) was used as blended with diesel fuel (DF) by 50% oil–50% diesel fuel in volume (O50) also as blended with diesel fuel by 20% oil–80% diesel fuel in volume (O20). The test fuels were used in a single cylinder, four stroke, naturally aspirated, direct injection compression ignition engine. The effects of fuel preheating to 100 °C on the engine performance and emission characteristics of a CI engine fueled with rapeseed oil diesel blends were clarified. Results showed that preheating of RRO was lowered RRO’s viscosity and provided smooth fuel flow Heating is necessary for smooth flow and to avoid fuel filter clogging. It can be achieved by heating RRO to 100 °C. It can also be concluded that preheating of the fuel have some positive effects on engine performance and emissions when operating with vegetable oil.     

Generating efficiency and emissions of a spark-ignition gas engine generator fuelled with biogas–hydrogen blends

We investigated the generating efficiency and pollutant emissions of a four-stroke spark-ignition gas engine generator operating on biogas–hydrogen blends of varying excess air ratios and hydrogen concentrations. Experiments were carried out at a constant engine speed of 1200 rpm and a constant electric power output of 10 kW. The experimental results showed that the peak values of generating efficiency, maximum cylinder pressure, and NO_x emissions were elevated at an excess air ratio of around 1.2 as the hydrogen concentration was increased. CO₂ emissions decreased as the excess air ratio and hydrogen concentration increased, due to lean-burn conditions and hydrogen combustion. An efficiency per NO_x emissions ratio (EPN) was defined to consider the relationship between the generating efficiency and NO_x emissions. A maximum EPN value of 0.7502 was obtained with a hydrogen concentration of 15%, for an excess air ratio of 2.0. At this EPN value, the NO_x and CO₂ emissions were 39 ppm and 1678.32 g/kWh, respectively, and the generating efficiency was 29.26%. These results demonstrated that the addition of hydrogen to biogas enabled the effective generation of electricity using a gas engine generator through lean-burn combustion.     

Experimental investigation on performance and emissions of a spark-ignition engine fuelled with natural gas–hydrogen blends combined with EGR

An experimental investigation on the influence of different hydrogen fractions and EGR rates on the performance and emissions of a spark-ignition engine was conducted. The results show that large EGR introduction decreases the engine power output. However, hydrogen addition can increase the power output at large EGR operation. Effective thermal efficiency shows an increasing trend at small EGR rate and a decreasing trend with further increase of EGR rate. In the case of small EGR rate, effective thermal efficiency is decreased with the increase of hydrogen fraction; while in the case of large EGR rate, thermal efficiency is increased with increasing of hydrogen fraction. For a specified hydrogen fraction, NO_x concentration is decreased with the increase of EGR rate and this effectiveness becomes more obviously at high hydrogen fraction. HC emission is increased with the increase of EGR rate and it decreases with the increase of hydrogen fraction. CO and CO₂ emissions show little variations with EGR rate, but they decrease with the increase of hydrogen fraction. The study shows that natural gas–hydrogen blend combining with EGR can realize high-efficiency and low-emission spark-ignition engine.     

A comparison of the performance analysis of the spark ignition engine fuelled with ethanol–iso-octane and methanol–iso-octane fuel blends

In this research, the effects of unleaded iso-octane (base fuel), iso-octane–ethanol blend (E20) and iso-octane–methanol blend (M20) on engine performance were investigated experimentally in a single-cylinder four-stroke spark-ignition engine. The tests were performed by varying the throttle position and engine speed at a constant load of 8 kg. The engine speed was varied from 1200 to 1750 rpm, with changing the throttle position. The results showed that ethanol and methanol addition to unleaded iso-octane increases the engine torque, power and brake-specific fuel consumption (BSFC) in comparison to base fuel. The results also showed that exhaust temperature increases with the increase in engine speed. The thermal efficiency varies from 14.3% to 35.9% for iso-octane, 20.1–30.59% for E20 and (17.64–27.46%) for M20 fuel. It was also found that the volumetric efficiency of M20 and E20 fuels was higher than that of iso-octane in all speed ranges.