SrAl2 O4:Eu2+,Dy3+/TPE发光材料的制备及其光学性能

SrAl2O4:Eu2+,Dy3+/TPE是一种新型发光材料,用其制备的电缆护套在黑暗条件下可快速检测电缆状态.本研究先将稀土铝酸锶发光材料(SrAl2O4:Eu2+,Dy3+)与热塑性弹性体(thermoplastic elastomer,TPE)进行混合,再通过双螺杆挤出机共混制备了SrAl2O4:Eu2+,Dy3...     

电子束还原SrAl_2O_4:(Eu~(2+),Dy~(3+))长余辉材料的力致发光研究

通过高温烧结和电子束还原法制备了SrAl2O4:(Eu2+,Dy3+)长余辉发光材料,并利用球磨获得了SrAl2O4:(Eu2+,Dy3+)长余辉发光粉。通过把发光粉与环氧树脂混合制备了含有SrAl2O4:(Eu2+,Dy3+)长余辉发光粉的夜光胶,利用丝网印刷涂敷技术及热处理在石英玻璃上涂敷了厚度为1000 nm量级的SrAl2O4:(Eu2+,Dy3+)长余辉发光膜。通过小球下落冲击法和一套自制的基于一个雪崩二极管和皮安表的测试装置研究了这种长余辉发光膜的力致发光特性。研究发现,电子束还原法制备的SrAl2O4:(Eu2+,Dy3+)长余辉发光膜具有很好的力致发光特性,具有高达1.25的信背比和很高的信噪比。力致发光强度与小球下落前的初始高度即冲击发生前小球的动能成指数关系,光谱特性及衰减特性与长余辉发光相似。上述结果表明,力致发光是小球冲击能传递给电子并引起电子进入陷阱能级然后释放引起的。     

水热-均匀沉淀法制备亚微米长余辉发光材料SrAl_2O_4∶Eu,Dy

采用水热-均匀沉淀法,以尿素为沉淀剂,在聚四氟乙烯低温反应釜中160℃水热,在较低的煅烧温度下制备了亚微米级长余辉发光材料Sr0.97Al2O4∶Eu0.01,Dy0.02。XRD结果表明,在1000℃煅烧4h能得到单相的SrAl2O4∶Eu,Dy,SEM测试显示SrAl2O4∶Eu2+,Dy3+发光材料为球状形貌,粒径大小约为200～500nm,激发和发射光谱结果表明,随着煅烧温度升高,SrAl2O4∶Eu2+,Dy3+的发光强度也随之增强,其激发光谱峰值位于360nm,发射光谱峰值位于513nm,SrAl2O4∶Eu2+,Dy3+在1100℃煅烧后的余辉衰减时间比1000℃煅烧后显著提高,其热释光谱峰值在80～90℃。     

PMMA/硅铝包覆铝酸锶复合发光材料的制备和发光性能

采用原位乳液聚合法制备了聚甲基丙烯酸甲酯(PMMA)/硅铝包覆(SrAl2O4:Eu,Dy)复合发光材料。通过傅立叶变换红外光谱(FT-IR)和热失重(TGA)测定,研究了复合发光材料的结构,结果表明,复合发光材料中聚合物分子与硅铝包覆(SrAl2O4:Eu,Dy)之间是通过键合的方式结合;通过荧光光谱和发光亮度测试,研究了复合发光材料的发光特性和余辉性能,结果表明,在硅铝包覆(SrAl2O4:Eu,Dy)表面共价结合上PMMA后仍能保持SrAl2O4:Eu,Dy原有的发光性能。     

Eu2+、Dy3+、Li+共掺杂CaSi2O2N2荧光粉的发光性能

采用高温固相反应法制备了一系列白光LED用CaSi2O2N2:0.05Eu2+,xDy3+,xLi+(0≤x≤0.03)荧光粉.利用X射线衍射仪对样品的物相结构进行了分析,结果表明:Dy3+和Li+离子的掺入没有改变CaSi2O2N2:Eu2+荧光粉的主晶相.利用荧光光谱仪对样品的发光性能进行了测试,发现所有样品的激发光谱均覆盖了从近紫外到蓝光的较宽范围,400 nm激发下得到的发射光谱为宽波段的单峰,峰值位于545 nm左右,是Eu2+离子5d-4f电子跃迁引起的.Dy3+离子掺杂可以提高CaSi2O2N2:Eu2+荧光粉的发光强度,Dy3+与Li+共掺杂可进一步提高荧光粉的发光强度,当Dy3+和Li+的掺杂量为1mol%时,荧光粉的发光强度达到最大值,是单掺杂Eu2+的荧光粉发光强度的157%.     

硼在Eu2+,Dy3+共激活srAl2 O4发光材料中作用的研究进展

概括了SrAl2O4:Eu2 ,Dy3 在加硼和不加硼条件下的合成和性能对比,阐述了硼掺杂对Eu2 ,Dy3 共激活SrAl2O4的影响及作用:一方面,硼作为助熔剂可以降低烧成温度促使单斜SrAl2O4相的形成;另一方面,硼掺杂能促进Eu3 的还原以及Eu离子在SrAl2O4体系中的扩散和取代并促使发光中心的形成和稳定,从而使得材料的发光性能有所改善.此外,硼掺杂也引入了一些问题,如粉体烧结等,也对此做了概括并提出了展望.     

煅烧温度对红色长余辉发光材料Sr_3Al_2O_6:Eu~(2+),Dy~(3+)性能的影响

采用溶胶凝胶法合成了Sr3Al2O6:Eu2+,Dy3+长余辉发光材料,利用X射线衍射仪(XRD)对材料的物相进行了分析,采用荧光分光光度计、照度计测定了样品的发光特性。XRD结果表明:随着煅烧温度的升高,SrCO3杂相的衍射峰越来越弱,Sr3Al2O6相的衍射峰越来越强,1200℃时发光基质为纯的Sr3Al2O6相,1250℃时出现新的SrAl2O4杂相。激发光谱和发射光谱结果表明:长余辉发光材料的激发峰位于473nm,发射峰位于612nm,归属于Eu2+的4f65d1→4f7特征发光。温度升至1250℃时,Eu2+的发射峰为612nm和520nm,后者归属于Eu2+在发光基质SrAl2O4中的发光。综合分析得制备Sr3Al2O6:Eu2+,Dy3+发光材料合适的煅烧温度为1200℃,在此温度下,材料具有较好的初始亮度和余辉时间。     

碱土金属长余辉材料的耐酸碱性研究

分别对发光性能最好的铝酸盐基质长余辉材料SrAl2O4∶Eu2+,Dy3+与硅酸盐基质长余辉材料Sr2MgSi2O7∶Eu2+,Dy3+进行酸、碱处理(以HNO3和NaOH为例),研究其耐酸碱性能。XRD、SEM、激发光谱、发射光谱以及余辉特性测试的结果表明:SrAl2O4∶Eu2+,Dy3+及Sr2MgSi2O7∶Eu2+,Dy3+经酸、碱处理后物相发生了部分改变,其激发与发射光谱的强度随着酸碱度的增大而降低,但峰形与峰位没有改变;SrAl2O4∶Eu2+,Dy3+经酸碱处理后表面变得更不平整,棱角变得不明显;SrAl2O4∶Eu2+,Dy3+经酸处理后的初始亮度为未处理时的39.2%,经碱处理后的初始亮度为未处理时的14.0%;Sr2MgSi2O7∶Eu2+,Dy3+经酸碱处理后晶体的结构、形貌、表面及余辉衰减情况基本无变化。     

热释发光-正电子湮灭法研究SrAl2O4基磷光体长余辉发光机制

利用传统陶瓷制备方法合成了长余辉SrAl2O4：Eu，Dy发光粉材料，并利用热释发光—正电子湮灭法对该材料的发光性能及机理进行了研究。研究结果表明，掺杂的Eu在基质材料中主要充当发光中心，而Dy离子主要充当陷阱能级。正电子湮灭试验结果表明，Sr0.94Al2O4：Eu0.02和Sr0.94Al2O4：Eu0.02，Dy0.04存在带负电中心的缺陷，共掺杂的Dy^3 进到Sr^2 位，同时产生一定量的Sr空位，热释发光谱结果表明，单掺杂Eu离子的磷光体中缺陷陷阱深度较深，约为0．95eV，随着Dy的共掺杂，热释发光强度相应增加，陷阱深度降为0．51eV，对于长余辉发光机制，认为陷阱能级捕获的空穴与介稳态(Eu^1 )^*的复合，导致了长余辉现象的发生，并且由于陷阱深度的变化，导致余辉性能出现较大的差异。     

溶胶-凝胶法制备铝酸锶发光材料

用溶胶 凝胶法合成制备铝酸锶 (SrAl2 O4:Eu2 + (SE) ,SrAl2 O4:Eu2 + ,Dy3+ (SED) )体系长余辉发光材料 ,用X射线粉晶衍射仪 (XRD)、荧光光度计等对制备产物进行了分析测试。用溶胶 凝胶法 (Sol gel)制备铝酸锶长余辉体的最佳温度为 1 2 0 0～ 1 2 5 0℃。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from