Crystallization behavior of poly(ethylene terephthalate)/multiwalled carbon nanotubes composites

Crystallization behavior of poly(ethylene terephthalate)/multiwalled carbon nanotubes (PET/MWNTs) composites have been investigated under isothermal conditions and in comparison with the conventional nucleating agents, sodium benzoate, and micrometric carbon/glass fibers. In the PET/MWNTs composites, MWNTs promote the crystallization of PET as a heterogeneous nucleating agent, and the nucleation efficiency is greatly enhanced when MWNTs was homogeneously dispersed in PET matrix. In comparison with pure PET, spherulites size of PET/MWNTs composites is significantly reduced, and the shape becomes quite irregular. TEM images indicate that MWNTs bundles locate in the center of spherulites of PET and act as nuclei. Fold surface free energy during nucleation process for MWNTs nucleated PET is just half of pure PET, suggesting that MWNTs are efficient nucleating agents for PET. The sequence of nucleating ability of is given as follows: sodium benzoate>MWNTs>talc>carbon fibers≈glass fibers. The nucleation in the presence of sodium benzoate is a chemical nucleation process that may cause severe degradation of PET, but MWNTs nucleate PET through “particle effect,” which does not affect the molecular weight of PET. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(lauryl acrylate) and poly(stearyl acrylate) grafted multiwalled carbon nanotubes for polypropylene composites

Two new polymer grafts on an industrial grade multiwalled carbon nanotube (MWCNT) were prepared through a non-oxidative pathway employing controlled free radical polymerization for surface initiated polymer grafting. After photochemical introduction of an ATRP initiator onto the MWCNT, polymerizations of lauryl or stearyl acrylate were performed, resulting in two novel polymer modifications on the MWCNT (poly(lauryl acrylate) or poly(stearyl acrylate)). The method was found to give time dependent loading of polymers as a function of time (up to 38 wt% for both acrylates), and showed a plateau in loading after 12 h of polymerization. The modified nanomaterials were melt mixed into polypropylene composites with very low filler loading (0.3 wt%), whereafter both the thermal and electrical properties were investigated by DSC and dielectric resonance spectroscopy. The electrical properties were found to be substantially improved, where poly(lauryl acrylate) was found to be the superior surface modification, resulting in a conductive composite.     

Synthesis and characterization of poly(acrylonitrile-co-methylmethacrylate) nanocomposites reinforced by functionalized multiwalled carbon nanotubes

Polyacrylonitrile-co-poly(methylmethacrylate)/multiwalled carbon nanotubes (PAN-co-PMMA/MWCNTs) nanocomposites were synthesized by an in situ emulsifier-free polymerization method with variable percentages of functionalized carbon nanotube (f-MWCNT). MWCNTs were functionalized with concentrated H₂SO₄ and HNO₃ with a continuous sonication process. Chemical interaction of f-MWCNT with the copolymer was studied by UV-visible spectroscopy. Fourier transform infrared spectroscopy proved the interaction of f-MWCNT with the PAN-co-PMMA copolymer matrix. The structural interaction of f-MWCNT with copolymer matrix was investigated by X-ray diffraction study. The dispersion and morphology of the f-MWCNT in the copolymer matrix were studied by scanning electron microscopy and high-resolution transmission electron microscopy. It was noticed that the f-MWCNTs were uniformly dispersed within the copolymer matrix. The thermal property of the PAN-co-PMMA/f-MWCNT nanocomposite was analyzed by thermogravimetric analysis. It was noticed that the thermal stability of the PAN-co-PMMA/f-MWCNT nanocomposite was more than that of the virgin copolymer matrix. When the electrical conductivity property of the synthesized nanocomposite was measured, it was noticed that the better dispersion of f-MWCNT in the non-conductive PAN-co-PMMA copolymer matrix made the PAN-co-PMMA/f-MWCNT nanocomposites conductive. From the measurement of gas barrier properties of synthesized nanocomposites, it was assumed that the well-dispersed f-MWCNT in the copolymer matrix creates the huddles for penetration of oxygen gas. It was noticed that the oxygen permeability of the PAN-co-PMMA/f-MWCNT nanocomposite was reduced by five times as compared to that of the neat PAN-co-PMMA copolymer matrix. The PAN-co-PMMA/f-MWCNT nanocomposites with higher thermal stability and reduced oxygen permeability properties may be suitable for application as conducting packaging materials.     

Nanocomposites of poly(vinylidene fluoride) with multiwalled carbon nanotubes

The preparation and characterization of nanocomposites of poly(vinylidene fluoride), PVDF, with acid treated multiwalled carbon nanotubes (MWCNT) with a wide composition range, from 0.1 to 5.0% MWCNT by weight, is reported. Effect of uniaxial orientation by zone drawing on these nanocomposites is discussed and compared with unoriented compression molded films. Static room temperature two‐dimensional wide angle X‐ray scattering and Fourier transform infrared spectroscopy were used for phase identification. Differential scanning calorimetry, polarizing optical microscopy, dynamic mechanical analysis (DMA), and thermogravimetic analysis (TGA) were used to study the thermal and mechanical properties. Incorporation of MWCNT into PVDF has no obvious effect in forming beta phase crystal in the PVDF/MWCNT bulk films, while zone drawing cause a significant alpha to beta transition in PVDF/MWCNT. Results indicate that MWCNTs act as nucleation agent during crystallization and slightly increase the degree of crystallinity of PVDF/MWCNT bulk films. TGA indicates the thermal stability is improved when MWCNT concentration increases for unoriented PVDF/MWCNT film. The modulus also increases significantly when MWCNT concentration increases. The glass transition temperature measured by the peak position of tanδ from DMA does not change with MWCNT concentration, but a slightly higher glass transition can be obtained by zone drawing. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Functionalization of multiwalled carbon nanotubes with amphiphilic poly(aspartic acid)

A new method to functionalize multiwalled carbon nanotubes (MWNTs) with amphiphilic poly(aspartic acid) was investigated. The amphiphilic polymer (PASP‐C16) was synthesized by thermal condensation and aminolysis by hexadecylamine, followed by hydrolysis of the remaining succinimide units in the polymer backbone. The functionalization of MWNTs was achieved by physical adsorption of the biopolymer onto the surfaces of MWNTs. Ultraviolet‐visible ( UV‐vis) spectra showed that the functionalized MWNTs had a good aqueous dispersity and solubility. The interaction of PASP‐C16 with MWNTs was investigated by analyzing X‐ray diffraction (XRD) patterns, circular dichroism (CD), spectra and high‐resolution transmission electron microscopy ( HRTEM ). From the XRD patterns, it can be known that the aggregate of PASP‐C16 due to intermolecular interaction between hexadecyl chains has been reduced when the polymer interacting with MWNTs. CD spectra indicated that the interaction of hexadecyl chains of PASP‐C16 with the wall of MWNTs is the major interaction between PASP‐C16 and MWNTs, and MWNTs were covered by the poly(aspatic acid) backbone. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

Morphology and physical properties of nanocomposites based on poly(methyl methacrylate)/poly(vinylidene fluoride) blends and multiwalled carbon nanotubes

Nanocomposites of blends of poly(vinylidene fluoride) (PVDF) and poly(methyl methacrylate) (PMMA) with multiwalled carbon nanotubes (CNTs) were prepared by melt mixing and hot press molding followed by quenching or annealing (120°C, 24 h). PMMA‐rich nanocomposites showed higher electrical conductivity than PVDF‐rich samples at identical CNT loading. At a specific composition, the quenched nanocomposites showed electrical conductivity values three to four orders of magnitude higher than those observed in annealed samples. Measurement of the dielectric constants also supported the electrical conductivity results. In the annealed samples, agglomerated CNTs located mainly in the PVDF crystalline phase were observed. Addition of CNTs promoted the crystallization, and especially, the formation of β‐crystals, which was confirmed by X‐ray diffraction. The thermal behavior of nanocomposites from differential scanning calorimetry (DSC) analysis was explained in terms of the three‐phase model involving the presence of the rigid amorphous fraction, the mobile amorphous fraction, and the crystalline phase. POLYM. COMPOS., 36:1195–1204, 2015. © 2014 Society of Plastics Engineers     

Morphology,crystallization, and mechanical properties of poly(ethylene terephthalate)/multiwalled carbon nanotubes composites

Poly(ethylene terephthalate)/multiwalled carbon nanotubes (PET/MWCNTs) with different MWCNTs loadings have been prepared by in situ polymerization of ethylene glycol (EG) containing dispersed MWCNTs and terephthalic acid (TPA). From scanning electronic microscopy images of nanocomposites, it can be clearly seen that the PET/MWCNTs composites with low‐MWCNTs contents (0.2 and 0.4 wt %) get better MWCNTs dispersion than analogous with high‐tube loadings (0.6 and 0.8 wt %). The nonisothermal crystallization kinetics was analyzed by differential scanning calorimetry using Mo kinetics equation, and the results showed that the incorporation of MWCNTs accelerates the crystallization process obviously. Mechanical testing shows that, in comparison with neat PET, the Young's modulus and the yield strength of the PET nanocomposites with incorporating 0.4 wt % MWCNTs are effectively improved by about 25% and 15%, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

In situ synthesis and characterization of poly(2,5-benzoxazole)/multiwalled carbon nanotubes composites

This article reports the synthesis of poly(2,5-benzoxazole)/multiwalled carbon nanotubes (ABPBO/MWNT) composites by in situ polycondensation and their chemical and physical properties. The functional groups yielded from the surface modification of MWNTs by hydrochloric acids have been demonstrated to participate in the polymerization and thus led to the composites with homogenous dispersion of carbon nanotubes. The chemical structures and morphology of the afforded polymer composites have been fully characterized by FTIR, WAXD, UV-vis, TGA and SEM. The ABPBO/MWNT composites exhibit excellent thermal stability and greatly improved mechanical properties. The tensile modulus and tensile strength of the composites are 47% and 83%, respectively, higher than those of the polymer matrix. The dielectric constant of the composites is also significantly enhanced from 4 of the polymer matrix to 65 with the incorporation of 5 wt% MWNTs.     

Preparation and characterization of poly(vinylidene fluoride) nanocomposites containing multiwalled carbon nanotubes

Poly(vinylidene fluoride) (PVDF) nanocomposites with different loadings of multiwalled carbon nanotubes (MWNT) were prepared by melt‐compounding technique. A homogeneous dispersion of MWNT throughout PVDF matrix was observed on the cryo‐fractured surfaces by scanning electron microscopy. Thermogravimetric analysis results indicated that the thermal stability of neat PVDF was improved with the incorporation of MWNT. Dynamic mechanical analysis showed a significant improvement in the storage modulus over a temperature range from ?125 to 75°C with the addition of MWNT. The melt‐rheological studies illustrated that incorporating MWNT into PVDF matrix resulted in higher complex viscosities (|η*|), storage modulus (G′), loss modulus (G″), and lower loss factor (tan δ) than those of neat PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of preparation methods on the electrical and nanomechanical properties of poly(methyl methacrylate)/multiwalled carbon nanotubes composites

Poly(methyl methacrylate)/multiwalled carbon nanotubes (PMMA/MWCNT) composites were prepared by two different methods: melt mixing and solution casting. For solution casting, two different solvents, toluene and chloroform, were used to prepare PMMA solutions with different concentrations of MWCNT. The dispersion of the CNT in the composite samples was verified by scanning electron microscopy. For the nanocomposites prepared by both methods, the electrical conductivity increased with increasing filler content, showing typical percolation behavior. In addition, an increase of 11 orders of magnitude in the electrical conductivity relative to the matrix conductivity was determined by broadband dielectric spectroscopy and four probe conductivity measurements. A maximum value of σ_DC ～ 1.6 S/cm was found for the highest filler loaded sample (3.67 vol %), which was prepared by solution casting from toluene. Nanoindentation analysis was used to characterize the surface mechanical properties of the composite samples prepared by the different methods. Indentation tests were performed at various penetration depths, and it was revealed that the melt mixing process resulted in stiffer neat PMMA samples compared to the solution casted PMMA samples. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41721.     

Synthesis and characterization of multiwalled carbon nanotube/polyurethane composites via surface modification multiwalled carbon nanotubes using silane coupling agent

Well‐dispersed multiwalled carbon nanotubes/polyurethane (MWCNTs/PU) composites were synthesized in situ polymerization based on treating MWCNTs with nitric acid and silane coupling agent. The morphology and degree of dispersion of the MWCNTs were studied using a high resolution transmission electron microscopy (HR‐TEM) and X‐ray powder diffraction (XRD). The result showed that MWCNTs could be dispersed still in the PU matrix well with the addition of 2 wt% MWCNTs. The thermal and mechanical properties of the composites were characterized by dynamic mechanical thermal analysis, thermogravimetric analysis, tensile, and impact testing. The result suggested that the glass transition temperature (T_g) of composites increased greatly with increasing MWCNTs content slightly, and the MWCNTs is also helpful to improve mechanical properties of composites. Furthermore, the composites have an excellent mechanical property with the addition of 0.5 wt% MWCNTs. The electrical property testing indicates that the MWCNTs can improve evidently the electrical properties of composites when adding 1 wt% MWCNTs to the PU matrix. The volume resistivity of composites reaches to an equilibrium value. POLYM. COMPOS., 33:1866–1873, 2012. © 2012 Society of Plastics Engineers     

Synthesis and characterization of hybrid composites based on carbon nanotubes

Multi-wall carbon nanotubes (CNTs) were coated with protonated polyaniline (PAni) in situ during the chemical polymerization of aniline. Uniform coating of CNT with PAni was observed by scanning electronic microscopy. An improvement in the covering of CNT composites was found by the association of poly(2,5-dimercapto-1,3,4-thiadiazole) (PDMcT). The conductivity of composites has been compared with the conductivity of the PAni and CNT. A maximum conductivity of 96.8 S cm⁻¹ has been found for a PAni/PDMcT/CNT composite. High capacitance value (289.4 F g⁻¹) was also determined for this composite, indicating that all materials, PAni, PDMcT and CNT, remain active during the charge–discharge cycling. The reduction in the capacitance after 100 cycles was found to be less than 25%. The capacitive behavior of all materials was confirmed by impedance analysis.     

Nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes in poly(p‐phenylene sulfide) composites

To investigate the nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes (MWNTs‐OH) in poly(p‐phenylenesulfide) (PPS), a series of composites were prepared by blending PPS with MWNTs‐OH at 1, 2, and 3 wt %, respectively. Under SEM observation MWNTs‐OH were found homogeneously dispersed in the PPS matrix. DSC thermograms revealed that the enthalpy (ΔH_c) of the composites increased with increasing MWNT‐OH content, whereas the crystallization temperature (T_c) decreased progressively. The decrease in T_c was in accordance with the smaller crystallite size determined with WXRD characterization, and the increase in ΔH_c was evidenced by FTIR and XPS analyses. The higher ΔH_c shows that MWNTs‐OH serves as a nucleating agent, providing sufficiently multiplied sites for crystal growth. The lowering of T_c was attributed not only to MWNTs‐OH network hindrance to PPS chain fusing rearrangement, but also to a poorer affinity between MWNTs‐OH and PPS; both effects coordinately govern T_c of PPS/MWNTs‐OH composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and crystallization behavior of multiwalled carbon nanotubes/poly(vinyl alcohol) nanocomposites

The poly(vinyl alcohol) (PVA)‐based nanocomposites embedded with modified multiwalled carbon nanotubes (MWCNTs) were prepared. To enhance the interfacial interaction between MWCNTs and PVA, acid‐treated MWCNTs were grafted with PVA chains, compatibilizing MWCNTs and the matrix. The better dispersion of MWCNTs in PVA matrix was obtained by the introduction of MDI reaction bridges and then PVA molecules onto the surface of MWCNTs. Moreover, strong interaction between MWCNTs and PVA matrix was evidenced through the measurement results of the melting behavior, polarized Raman measurement, and nonisothermal crystallization behavior of the nanocomposites. Owing to the reinforcement of MWCNTs, the tensile strength and modulus of PVA nanocomposite containing 0.9 wt% MWCNTs were increased by 160.7 and 109.2%, respectively, compared to neat PVA. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Study on physical properties of multiwalled carbon nanotube/poly(phenylene sulfide) composites

The multiwalled carbon nanotubes were directly compounded with poly(phenylene sulfide) (PPS) via melt mixing. The morphology and physical properties, including viscoelasticity, electrical conductivity, and thermal and mechanical properties, of the obtained composites were investigated. The results show that the purified nanotubes can be fully dispersed in the PPS matrix especially at low loading levels because of their good affinity. The composites hence present relative low rheological and electrical percolation thresholds. The presence of nanotubes, on the one hand, shows good reinforcement effect because of the strong interfacial interactions with the PPS matrix, which is confirmed by the strain overshoot flow behavior, and, on the other hand, acts as a nucleation agent, promoting crystallization of the PPS matrix. Both contribute to evident improvement of tensile strength and dynamic mechanical properties of the composites. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Dual-stimuli sensitive composites based on multi-walled carbon nanotubes and poly(N,N-diethylacrylamide-co-acrylic acid) hydrogels

A strategy to prepare dual-stimuli sensitive poly(N,N-diethylacrylamide-co-acrylic acid) composite hydrogels has been demonstrated. Multi-walled carbon nanotubes (MWCNTs) functionalized with vinyl groups were copolymerized with N,N-diethylacrylamide (DEA), acrylic acid (AA) and N,N′-methylenebisacrylamide (NNMBA) to obtain the composites (NCG). As expected, the compression properties of the NCG were greatly improved without noticeably reducing the response rates to temperature changes. Field emission scanning electron microscopy showed that the surface of the NCG was denser, which affords the NCG better compression properties, while there was obvious MWCNTs aggregation on the surface of the hybrid gel sample by physical mixing of the MWCNTs (HYG).     

Hydrogen bond containing multiwalled carbon nanotubes in polyurethane composites

Introduction of hydrogen bonding sites onto multi‐walled carbon nanotubes (MWCNTs) included carboxylic acid, amide‐amine, and novel amide‐urea MWCNTs for the formation of homogenous polyurethane composites. Acid oxidation and subsequent derivatization introduced hydrogen bonding functionality onto MWCNTs to reveal the effect of surface functionalization on mechanical properties in a 45 wt% hard segment polyurethane matrix. Raman spectroscopy showed an increase in the D/G peak ratio, which indicated successful oxidation, and X‐ray photoelectron spectroscopy also revealed elemental compositions that supported each step of the functionalization strategy. Thermogravimetric analysis supported functionalization with an increase in percent weight loss for each functionalization, and the MWCNT surface functionalization determined pH‐dependent dispersibility. The nonfunctionalized MWCNT composites showed poor dispersion with transmission electron microscopy, and in sharp contrast, the functionalized composites displayed homogenous dispersions. Tensile testing revealed improved stress at break in the functionalized MWCNT composites at low loadings due to homogenous dispersion. POLYM. COMPOS., 37:1425–1434, 2016. © 2014 Society of Plastics Engineers     

Synthesis and characterization of multiwalled carbon nanotubes-protoporphyrin IX composites using acid functionalized or nitrogen doped carbon nanotubes

In this research we describe the synthesis and characterization of composite materials based on multiwalled carbon nanotubes and protoporphyrin IX. We compare the results of using three types of carbon nanotubes: pristine (diameter < 10 nm), acid functionalized (diameter < 10 nm), and nitrogen doped carbon nanotubes (diameter ≈ 20 nm). Carbon nanotubes were mixed with protoporphyrin IX via two simple and straightforward methods using sonication, or heating-stirring. The characterization of the composites was done by Raman spectroscopy, field emission scanning electron microscopy, thermogravimetric analysis, ultraviolet-visible and fluorescence spectroscopy and infrared spectroscopy. A diversity of coatings of the nanotubes by protoporphyrin were obtained depending on the type of nanotube used or the method of synthesis. Some carbon nanotubes increased their diameter up to 40% after the reaction with protoporphyrin. Percentages by weight up to 20% of protoporphyrin were measured by thermogravimetric analysis. We obtained experimental evidences by different techniques of the electronic interaction and the formation of covalent bonds between both constituents, above all for the composites using nanotubes < 10 nm in diameter. Some of these evidences were ~ 98% of fluorescence quenching, reduction in the intensity of the absorption bands in ultraviolet visible spectroscopy, strong reduction in the intensity of some bands in Raman spectroscopy, red and blue shifts, as well as the presence of new absorption bands in infrared spectroscopy. Nitrogen doped carbon nanotubes showed low chemical reactivity to protoporphyrin IX, perhaps due to their lower acceptor character as they could have charge transfer from nitrogen dopants to the nanotube network, or because of their metallic character.     

In situ polymerization and photophysical properties of poly(p‐phenylene benzobisoxazole)/multiwalled carbon nanotubes composites

Poly(p‐phenylene benzobisoxazole)/multiwalled carbon nanotubes (PBO‐MWCNT) composites with different MWCNT compositions were prepared through in situ polymerization of PBO in the presence of carboxylated MWCNTs. The nanocomposite's structure, thermal and photophysical properties were investigated and compared with their blend counterparts (PBO/MWCNT) using Fourier transform infrared spectra, Raman spectra, Wide‐angle X‐ray diffraction, thermogravimetric analysis, UV‐vis absorption, and photoluminescence. The results showed that MWCNTs had a strong interaction with PBO through covalent bonding. The incorporation of MWCNTs increased the distance between two neighboring PBO chains and also improved the thermal resistance of PBO. The investigation of UV‐vis absorption and fluorescence emission spectra exhibited that in situ PBO‐MWCNT composites had a stronger absorbance and obvious trend of red‐shift compared with blend PBO/MWCNT composites for all compositions. This behavior can be attributed to the efficient energy transfer through forming conjugated bonding interactions in the PBO‐MWCNT composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and thermal properties of functionalized multiwalled carbon nanotubes and multiwalled carbon nanotube–polyurethane composites

Multiwalled carbon nanotube (MWNT)–polyurethane (PU) composites were obtained by an in situ polycondensation approach. The effects of the number of functional groups on the dispersion and mechanical properties were investigated. The results showed that the functionalized MWNTs had more advantages for improving the dispersion and stability in water and N,N′‐dimethylformamide. The tensile strength and elongation at break of the composites exhibited obvious increases with the addition of MWNT contents below 1 wt % and then decreases with additions above 1 wt %. The maximum values of the tensile strength and elongation at break increased by 900 and 741%, respectively, at a 1 wt % loading of MWNTs. Differential scanning calorimetry measurements indicated that the addition of MWNTs resulted in an alteration of the glass‐transition temperature of the soft‐segment phase of MWNT–PU. Additionally, new peaks near 54°C were observed with differential scanning calorimetry because of the microphase‐separation structures and alteration of the segment molecular weights of the hard segment and soft segment of PU with the addition of MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009