首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
Polyethersulfone (PES) hollow fiber membrane was prepared by blending with nonionic surfactant Tetronic 1307 to improve its hydrophilicity. The membranes were posttreated by hypochlorite solution of 10, 100, 500, and 2000 ppm. The effect of hypochlorite treatment on the performance of PES membrane was investigated. Experimental results showed that the water permeability of treated membrane was two to three times higher than that of untreated membrane in case of blend membrane prepared from PES/N‐methyl‐2‐pyrrolidone (NMP)/Tetronic 1307 solution. On the other hand, hypochlorite treatment has no effect on water permeability of the membrane prepared from PES/NMP solution. Elemental analysis and ATR–FTIR measurement results indicated that hypochlorite treatment led to decomposition and leaching out of Tetronic 1307 component from the membrane. The change of membrane surface structure by the hypochlorite treatment was confirmed by atomic force microscopy measurement. The hypochlorite treatment brought about no significant impact on the mechanical property of the membranes. This indicated that the hypochlorite treatment of PES membrane prepared with surfactant was a useful way to improve the water permeability without the decrease of membrane strength. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008  相似文献   

2.
Membrane fouling is still a crucial problem, especially in applications for water treatment. When fouling takes place on membrane surfaces, it causes flux decline, leading to an increase in production cost due to increased energy demand. The selection of the right membrane material and a special treatment of the membrane are required to avoid membrane fouling. This article reports the fouling resistance of a poly(ether sulfone) (PES) hollow‐fiber membrane modified with hydrophilic surfactant Tetronic 1307. Experiments on several methods of fouling were carried out to investigate the effect of the addition of nonionic surfactant Tetronic 1307 on membrane fouling. The effectiveness of a chemical agent [sodium hypochlorite (NaClO)] in the reduction of bovine serum albumin (BSA) deposition on the membrane surface was also evaluated. Permeation results showed that the fouling of a PES blend membrane with Tetronic 1307 was lower than that of the original PES membrane in the case of BSA filtration. A treatment with a 100 ppm NaClO solution was capable of removing BSA cake formation and effective at improving the relative permeability. The permeability of a PES blend membrane with Tetronic 1307 was almost 2 times higher than the original permeability when the membrane was treated with a 100 ppm NaClO solution because both BSA and Tetronic 1307 could be decomposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009  相似文献   

3.
In this study, effects of Tween 80 (polyoxyethylene sorbitan monooleate) as a variable hydrophilic surfactant additive on morphology and permeability of flat sheet polyethersulfone (PES) membranes prepared from PES/polyethylene glycol (PEG)/n-methyl-2-pyrrolidone (NMP) system via phase inversion induced by immersion precipitation in water coagulation bath were investigated. Cross-sectional morphology of the prepared membranes was studied by scanning electron microscopy (SEM). Permeation performance of the prepared membranes was evaluated in terms of pure water permeability (LP), water content, porosity, hydraulic permeability and thickness of the prepared membranes. It was found out that little addition of Tween 80 to the casting solution increases water content and porosity of the membrane support layer and enhances pure water permeability through the membranes.  相似文献   

4.
In this study, effects of coagulation bath temperature (CBT) and polyvinylpyrrolidone (PVP K15) concentration as a pore former hydrophilic additive on morphology and performance of asymmetric polyethersulfone (PES) membranes were investigated. The membranes were prepared from a PES/ethanol/NMP system via phase inversion induced by immersion precipitation in a water coagulation bath. The morphology of prepared membranes was studied by scanning electron microscopy (SEM), contact angle measurements, and mechanical property measurements. Permeation performance of the prepared membranes was studied by separation experiments using pure water and bovine serum albumin (BSA) solution as feed. The obtained results indicate that addition of PVP in the casting solution enhances pure water permeation flux and BSA solution permeation flux while reducing protein rejection. Increasing CBT results in macrovoid formation in the membrane structure and increases the membrane permeability and decreases the protein rejection. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers  相似文献   

5.
Blend PES/CA hydrophilic membranes were prepared via a phase-inversion process for oil–water separation. PEG-400 was introduced into the polymer solution in order to enhance phase-inversion and produce high permeability membranes. A gas permeation test was conducted to estimate mean pore size and surface porosity of the membranes. The membranes were characterized in terms of morphology, overall porosity, water contact angle, water flux and hydraulic resistance. A cross-flow separation system was used to evaluate oil–water separation performance of the membranes. From FESEM examination, the prepared PES/CA membrane presented thinner outer skin layer, higher surface porosity with larger pore sizes. The outer surface water contact angle of the prepared membrane significantly decreased when CA was added into the polymer solution. The higher water flux of the PES/CA membrane was related to the higher hydrophilicity and larger pore sizes of the membrane. From oil–water separation test, the PES/CA membrane showed stable oil rejection of 88 % and water flux of 27 l/m2 s after 150 min of the operation. In conclusion, by controlling fabrication parameters a developed membrane structure with high hydrophilicity, high surface porosity and low resistance can be achieved to improve oil rejection and water productivity.  相似文献   

6.
To construct a phase diagram of the polysulfone (PSF)/polyethersulfone (PES)/N‐methyl‐2‐pyrrolidone (NMP)/water quaternary system, cloud point measurements were carried out by a titration method. The miscible region in the PSF/PES/NMP/water quaternary system was narrow compared to the PSF/NMP/water and PES/NMP/water ternary systems. The binary interaction parameters between PSF and PES were estimated by water sorption experiments. The calculated phase diagram based on the Flory–Huggins theory fit the experimental cloud points well. In addition to the usual polymer–liquid phase separation, polymer–polymer phase separation, which resulted in a PSF‐rich phase and a PES‐rich phase, was observed with the addition of a small amount of nonsolvent. The boundary separating these two modes of phase separation could be well described and predicted from the calculated phase diagrams with the estimated binary interaction parameters of the components. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2113–2123, 1999  相似文献   

7.
Asymmetric polysulfone (PSF) membranes were prepared from PSF, Tetronic‐1107, and 1‐methyl‐2‐pyrrolidone (NMP) via immersion precipitation. Pure water was used as the gelation media. The effects of coagulation bath temperature (CBT) (0 and 25°C), and addition of Tetronic‐1107 on the morphology, wettability, and pure water permeation flux (PWF) of the prepared membranes were studied by scanning electron microscopy (SEM), atomic force microscopy (AFM), contact angle measurements, and experimental set up. The contact angle measurements demonstrated that the hydrophilicities of the nanoporous PSF membranes were significantly enhanced by addition of a small amount of Tetronic‐1107 surfactant in the casting solution, along with using the lower CBT. It was also found that addition of Tetronic‐1107 in the casting solution along with increasing the CBT from 0 to 25°C incites formation of bigger pores on the top surface and results in formation of membranes with higher thickness and more porous structure in the sublayer. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013  相似文献   

8.
Polyethersulfone (PES) is the most well-known polymer for the preparation of ultrafiltration (UF) membrane, but its membrane suffers from fouling. In this study, two engineered polymers were synthesized to provide optimal antifouling properties for UF membranes that simultaneously benefit from good properties of polyamide and PES. The choice of polyamide is due to its prominent characteristics and the convenience of its synthesis with various functional groups in a cost-effective way. Two hydroxyl containing polyamide bearing sulfone groups (PAS) and ether group (PAE) were synthesized by polycondensation method. The UF membranes were fabricated using the phase inversion method via immersion precipitation of PAS, PAE, and PES in dimethylacetamide, as a solvent and water, as a nonsolvent. The obtained membranes were compared and characterized by means of atomic force microscopy, scanning electron microscopy, contact angle, and Fourier transform infrared spectroscopy in the attenuated total reflection mode. The performance of membranes illustrated that the PAS and PAE membranes in comparison with the PES membrane had better porosity, water permeability, lesser protein fouling, more vertically finger-like pores, and more hydrophilic surface. The water permeability of PES, PAE, and PAS was 7.3, 64.0, and 78.0 L m−2 h−1 while their flux recovery ratio was 59.4, 83.3, and 86.7%, respectively. The promising permeability and antifouling properties of the PAS are potentially applicable in the efficient industrial separation and wastewater treatment. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48690.  相似文献   

9.
Polyethersulfone (PES) hollow‐fiber membranes were fabricated using poly(ethyleneglycol) (PEG) with different molecular weights (MW = PEG200, PEG600, PEG2000, PEG6000, and PEG10000) and poly(vinyl pyrrolidone) PVP40000 as additives and N‐methyl‐2‐pyrrolidone (NMP) as a solvent. Asymmetric hollow‐fiber membranes were spun by a wet phase‐inversion method from 25 wt % solids of 20 : 5 : 75 (weight ratio) PES/PEG/NMP or 18 : 7 : 75 of PES/(PEG600 + PVP40000)/NMP solutions, whereas both the bore fluid and the external coagulant were water. Effects of PEG molecular weights and PEG600 concentrations in the dope solution on separation properties, morphology, and mechanical properties of PES hollow‐fiber membranes were investigated. The membrane structures of PES hollow‐fiber membranes including cross section, external surface, and internal surface were characterized by scanning electron microscopy and the mechanical properties of PES hollow‐fiber membranes were discussed. Bovine serum albumin (BSA, MW 67,000), chicken egg albumin (CEA, MW 45,000), and lysozyme (MW 14,400) were used for the measurement of rejection. It was found that with an increase of PEG molecular weights from 200 to 10,000 in the dope solution, membrane structures were changed from double‐layer fingerlike structure to voids in the shape of spheres or ellipsoids; moreover, there were crack phenomena on the internal surfaces and external surfaces of PES hollow‐fiber membranes, pure water permeation fluxes increased from 22.0 to 64.0 L m?2 h?1 bar?1, rejections of three protein for PES/PEG hollow‐fiber membranes were not significant, and changes in mechanical properties were decreased. Besides, with a decrease of PEG600 concentrations in the dope solution, permeation flux and elongation at break decreased, whereas the addition of PVP40000 in the dope solution resulted in more smooth surfaces (internal or external) of PES/(PEG600 + PVP40000) hollow‐fiber membranes than those of PES/PEG hollow‐fiber membranes. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3398–3407, 2004  相似文献   

10.
张平允  李康康  徐超  郎万中 《净水技术》2021,40(1):37-43,87
以PES/DMAc/DEG低临界共溶温度(LCST)体系为铸膜液,利用低临界共溶温度(LCST)的热致相分离(LCST-TIPS,简称RTIPS)法制备PES微孔膜.探究影响PES微孔膜理化性能及其结构的2个主要因素:凝胶浴温度、非溶剂(DEG)/溶剂(DMAc)的质量比.运用扫描电镜(SEM)﹑纯水通量﹑BSA截留率...  相似文献   

11.
We prepared polyetherimide (PEI) hollow fiber membranes using polyvinylpyrrolidones (PVP) with different molecular weights (PVP 10,000, PVP 40,000, and PVP 1,300,000) as additives for oil/water separation. Asymmetric hollow fiber membranes were fabricated by wet phase inversion technique from 25 wt % or 30 wt % solids of 20 : 5 : 75 or 20 : 10 : 70 (weight ratio) PEI/PVP/N‐metyl‐2‐pyrrolidone (NMP) solutions and a 95 : 5 NMP/water solution was used as bore fluid to eliminate resistance on the internal surface. Effects of PVP molecular weights on morphology, oil‐surfactant‐water separation characteristics, mechanical, and thermal properties of PEI/PVP hollow fiber membranes were investigated. It was found that an increase in PVP molecular weight and percentage in PEI/PVP dope solution resulted in the membrane morphology change from the finger‐like structure to the spongy structure. Without sodium hypochlorite posttreatment, hollow fiber membranes with higher PVP molecular weights had a higher rejection but with a lower water flux. For oil‐surfactant‐water emulsion systems (1600 ppm surfactant of sodium dodecylbenzenesulfonate and 2500 ppm oil of n‐decane), experimental results illustrated that the rejection rates for surfactant, total organic carbon, and oil were 76.1 ≈ 79.8%, 91.0 ≈ 93.0%, and more than 99%, respectively. Based on the glass transition temperature values, PVP existed in hollow fiber membranes and resulted in the hydrophilicity of membranes. In addition, using NaOCl as a posttreatment agent for membranes showed a significant improvement in membrane permeability for PVP with a molecular weight of 1300 K, whereas the elongation at break of the treated hollow fiber membranes decreased significantly. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2220–2233, 1999  相似文献   

12.
Hydroxyl‐terminated polybutadiene (HTPB) was blended into a poly(ether sulfone) (PES) casting solution used to prepare ultra‐filtration (UF) membranes via the phase inversion technique. The membranes were then characterized by contact angle (CA) measurements and UF experiments. The CA was increased with the addition of HTPB in the PES membrane and also by lowering the gelation bath temperature. It was observed that the CA was lower for membranes prepared with N‐methyl‐2‐pyrrolidinone (NMP) as the solvent than those using N,N‐dimethylacetamide (DMAc) as solvent. The flux values were higher for membranes made using a 4°C gelation bath when compared with the ambient temperature ((25 ± 1)°C) irrespective of the cast solvents, NMP or DMAc. The flux values were much higher and the solute separations were lower for the HTPB‐based PES membranes than for the pure PES membrane, when the membranes were cast with DMAc as a solvent. On the other hand, both flux and separation values were much lower for the HTPB‐based PES membranes than for the pure PES membrane, when the membranes were cast using NMP. Atomic force microscopy and scanning electron microscopy were used for morphological characterization and the correlation of topography/photography with the performance data was also examined. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2292–2303, 2006  相似文献   

13.
The blend polyethersulfone (PES)/cellulose acetate (CA) flat‐sheet microporous membranes were prepared by reverse thermally induced phase separation (RTIPS) process. The effects of CA content and coagulation bath temperature on membrane structures and properties were investigated in terms of membrane morphology, water contact angle, permeation performance, and mechanical properties. The cloud point results indicated that the cloud point decreased with the increasing content of CA. When the coagulation bath temperature was lower than the cloud point, the membrane formation process underwent nonsolvent induced phase separation (NIPS) process and dense skin layer and finger‐like structure were formed in membranes. These membranes had lower pure water flux and poor mechanical properties. But when the coagulation bath temperature was higher than the cloud point, the membrane formation process underwent RTIPS process. The porous top surface as well as porous cross‐section of the membranes were formed. Therefore, high pure water flux and good mechanical properties were obtained. The contact angles results indicated that the hydrophilicity of the prepared membranes improved obviously with the addition of CA. When the content of CA was 0.5 wt% and the membrane formation temperature was 323K, the PES/CA microporous membrane which was prepared via the RTIPS process displayed a optimal permeability of the pure water flux of 816 L m?2 h?1 and the BSA rejection rate of 49.5%, which showed an increase of 48.9% and 23.6% than that of pure PES membrane, respectively. Moreover, the mechanical strengths of the membranes obtained by RTIPS process were better than those membranes prepared by NIPS process. POLYM. ENG. SCI., 58:180–191, 2018. © 2017 Society of Plastics Engineers  相似文献   

14.
In this article, the performance of polyethersulfone (PES) ultra‐ and nanofiltration membranes, prepared with the non‐toxic solvent dimethyl sulfoxide (DMSO), was investigated. The membranes were prepared by immersion precipitation via phase inversion. Experimental results proved that DMSO is a better alternative to N‐methyl‐2‐pyrrolidone (NMP) as solvent for PES ultrafiltration membranes as the membranes had a higher permeability and rejection of bovine serum albumin (BSA). An explanation was found based on experimental cloud point data and scanning electron microscopy images showing the morphology. The rejection of BSA and rose Bengal (RB) was proportional to the polymer concentration. On the contrary, the permeability decreased with increasing polymer concentration. For a casting thickness of 250 µm, an optimal balance between permeability and rejection of macromolecules for ultrafiltration was found at 24 wt % PES. The permeability was inversely proportional to the casting thickness, but a small decrease in rejection was observed when lowering the thickness. A good balance between permeability and rejection of RB was found, using a reference nanofiltration membrane of 28.5 wt % PES with 150 µm casting thickness. This membrane achieved a RB rejection of 95.3% and a pure water flux of 2.03 L m?2 h?1 bar?1. The membrane thickness and polymer concentration did not have a clear influence on the hydrophilicity of the membranes. It can be concluded that DMSO is a benign alternative as compared to traditional solvents such as NMP and also results in better PES membrane performances. DMSO is a perfectly suitable solvent for ultrafiltration applications and has potential to be used for nanofiltration applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46494.  相似文献   

15.
Flat-type poly(ether sulfone) (PES) membranes for ultrafiltration were prepared by the traditional phase-inversion technique. The effects of the concentration of PES and the combination of two solvents, dichloromethane (DCM) and N-methyl-2-pyrrolidone (NMP), with differences in volatility and solvating power on membrane performance were examined in terms of pure water flux (PWF) and solute rejection (SR) against poly(ethylene glycol) (PEG, MW 20,000). Changing the thermodynamic quality of PES/NMP casting solution by combining DCM, a volatile and weak solvent, affected the PWF of the resulting membrane. The SR of PES/DCM–NMP membrane, however, was more likely dependent upon the effect of evaporating the volatile solvent from the casting solution/air interface rather than the effect of changing the thermodynamic quality of the casting solution. Combining DCM in PES/NMP casting solution transformed the fingerlike macrovoids of PES/NMP membrane prepared without DCM into the isolated macrovoids. PES/DCM–NMP membrane prepared with PVP, a water soluble poreforming agent, showed an increased PWF while maintaining SR of over 90%, even under the reduced feeding pressure of 1 kg/cm2. It is necessary to measure molecular weight cutoff of membrane for demonstrating the potential of PVP for improving the membrane permeability without losing the selectivity.© 1996 John Wiley & Sons, Inc.  相似文献   

16.
The goethite nanoparticle was used as a multifunctional additive to fabricate antifouling polyethersulfone (PES) nanofiltration membranes. The goethite/PES membranes were synthesized via the phase inversion method. The scanning electron microscopy (SEM) photographs showed an increase in pore size and porosity of the prepared membranes with blending of the goethite. The static water contact angle measurements confirmed a hydrophilic modification of the prepared membranes. With increase in the goethite content from 0 to 0.1 wt %, the pure water flux increased up to 12.7 kg/m2 h. However, the water permeability decreased using high amount of this nanoparticle. Evaluation of the nanofiltration performance was performed using the retention of Direct Red 16. It was observed that the goethite/PES membranes have higher dye removal capacity (99% rejection) than those obtained from the unfilled PES (89%) and the commercial CSM NE 4040 NF membrane (92%). In addition, the goethite/PES blend membranes showed good selectivity and antifouling properties during long‐term nanofiltration experiments with a protein solution. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43592.  相似文献   

17.
In this work, surface grafting modification technology was combined with reverse thermally induced phase separation (RTIPS) method in order to improve the structure and permanent hydrophilicity of polyethersulfone (PES) membranes. Acrylic solution with different concentrations was grafted on the surface of PES membranes while grafting temperature and grafting time were also varied. The modified PES membranes were characterized in all aspects. Attenuated total reflectance Fourier transform-infrared confirmed successful modification of the PES membrane by grafting acrylic acid. Scanning electron microscopy revealed that homogeneous porous top surface as well as spongy-like cross-section structure appeared in the membrane by RTIPS procedure. Moreover, porosity was affected by changes of acrylic acid concentration, grafting temperature, and grafting time. Atomic force microscopy showed that grafting acrylic acid gave a reduction in roughness of PES membrane. Combined with the decreased values of contact angle, the hydrophilicity and antifouling performance of the PES membrane were improved. The pure water flux and BSA rejection rate of the grafted PES membranes were remarkably improved for pure PES membrane and attained a maximum, which was 1,646.24 L/(m2h) and 94.5%, respectively. The long-term test demonstrated that grafting membranes exhibited outstanding elevated water flux recovery ratio (>85%).  相似文献   

18.
In order to reduce surface aggregation and enhance the performance of PES membranes, a hydrophilic PES/TEOS HF membrane was developed for the treatment of wastewater containing oil. PES/TEOS was prepared via a sol-gel self assembly and dry–wet spinning method. Silicon dioxide sol was prepared from a mixture of tetraethoxysilane, ethanol, water, and acetic acid (acting as the catalyst). HF hybrid membranes were produced from dope solutions containing polyethersulfone, polyethylene glycol, silicon sol, and NMP. The membranes were characterized by field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), energy-dispersive X-ray spectroscopy (EDX), porosity, fourier transform infrared spectroscopy (FTIR), and contact angle measurements. The composite membranes were successfully used to treat wastewater containing oil and their separation performance were evaluated. The PES/TEOS-2 membrane displayed the best performance, with a permeate flux of 90.937 L/m2 h and an oil retention of 99.98%. In addition, this membrane showed a higher pure water flux of 102.43 L/m2 h as compared to PES-0 and PES/SiO2–1 membranes (87.347 L/m2 h and 91.949 L/m2 h, respectively). The PES/TEOS-2 membrane also presented enhanced antifouling behavior with a FRR and a RFR of 93.33% and 11.22%, respectively. In addition, this membrane displayed excellent long-term recycling properties, making it a desirable candidate for oily wastewater separation applications.  相似文献   

19.
Polyethersulfone (PES) nanofiltration (NF) membranes were prepared by blending of synthesized hydrophilic adipate ferroxane nanoparticles (AFNPs) as a novel multifunctional nanofiller via the phase inversion method. The water contact angle measurement indicated the higher hydrophilicity of the NF membranes. The water flux of the membranes improved significantly after the addition of AFNPs, from 10.4 to 32.2 kg/m2h. Antifouling characteristics of AFNPs/PES membranes were improved by increased hydrophilicity and decreased membrane surface roughness. The 0.6 wt% AFNPs/PES membrane exhibited the highest FRR (96%) and the lowest irreversible fouling resistance (6%). The nanofiltration performance of the prepared membranes was evaluated by dye removal and salt retention. The results proved the high dye removal capability of modified membranes (98% rejection) compared with the unfilled PES membrane (89% rejection). The salt retention sequence for membrane with 0.2 wt% of nanoparticles was Na2SO4 (70%)>MgSO4 (60%)>NaCl (18%).  相似文献   

20.
Hydrophilic and hydrophobic polyethersulfone (PES)-zinc oxide (ZnO) sublayers were prepared by loading of ZnO nanoparticles into PES matrix. Both porosity and hydrophilicity of the hydrophilic sublayer were increased upon addition of hydrophilic ZnO, while these were decreased for the hydrophobic sublayer. In addition, the results demonstrated that the hydrophilic membrane exhibited smaller structural parameter (S value or S parameter or S), which is beneficial for improving pure water permeability and decreasing mass transfer resistance. In contrast, a higher S parameter was obtained for the hydrophobic membrane. With a 2M NaCl as DS and DI water as FS, the pure water flux of hydrophilic TFN0.5 membrane was increased from 21.02 L/m2 h to 30.06 L/m2 h and decreased for hydrophobic TFN0.5 membrane to 14.98 L/m2 h, while the salt flux of hydrophilic membrane increased from 10.12 g/m2 h to 17.31 g/m2 h and decreased for hydrophobic TFN0.5 membrane to 3.12 g/m2 h. The increment in pure water permeability can be ascribed to reduction in S parameter, which resulted in reduced internal concentration polarization (ICP). The current study provides a feasible and low cost procedure to decrease the ICP in FO processes.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号