钌基氨合成催化剂氢氮吸附性能的研究

The effects of promoters K, Ba, Sm on the chemisorption and desorption of hydrogen and nitrogen, dispersion of metallic Ru and catalytic activity of active carbon (AC) supported ruthenium catalyst for ammonia synthesis have been studied by means of pulse chromatography, temperature-programmed desorption, and activity test. Promoters K, Ba and Sm increased the activity of Ru/AC catalysts for ammonia synthesis significantly, and particularly, potassium exhibited the best promotion on the activity because of the strong electronic donation to metallic Ru. Much higher activity can be obtained for Ru/AC catalyst with binary or triple promoters. The activity of Ru/AC catalyst is dependent on the adsorption of hydrogen and nitrogen. The high activity of catalyst could be ascribed to strong dissociation of nitrogen on the catalyst surface. Strong adsorption of hydrogen would inhibit the adsorption of nitrogen, resulted in decrease of the catalytic activity. Ru/AC catalyst promoted by Sm2O3 shows the best dispers     

反应条件对钌催化剂和铁催化剂的氨合成性能影响

Activated carbon-supported Ru-based catalyst and A301 iron catalyst were prepared,and the influences of reaction temperature,space velocity,pressure,and H2/N2 ratio on performance of iron catalyst coupled with Ru catalyst in series for ammonia synthesis were investigated.The activity tests were also performed on the single Ru and Fe catalysts as comparison.Results showed that the activity of the Ru catalyst for ammonia synthesis was higher than that of the iron catalyst by 33.5%-37.6% under the reaction conditions:375-400 °C,10 MPa,10000 h-1,H2︰N2 3,and the Ru catalyst also had better thermal stability when treated at 475 °C for 20 h.The outlet ammonia concentration using Fe-Ru catalyst was increased by 45.6%-63.5% than that of the single-iron catalyst at low tem-perature (375-400 °C),and the outlet ammonia concentration increased with increasing Ru catalyst loading.     

CO_2 methanation over TiO_2–Al_2O_3 binary oxides supported Ru catalysts

TiO_2 modified Al_2O_3 binary oxide was prepared by a wet-impregnation method and used as the support for ruthenium catalyst. The catalytic performance of Ru/TiO_2–Al_2O_3catalyst in CO_2 methanation reaction was investigated. Compared with Ru/Al_2O_3 catalyst, the Ru/TiO_2–Al_2O_3catalytic system exhibited a much higher activity in CO_2 methanation reaction. The reaction rate over Ru/TiO_2–Al_2O_3 was 0.59 mol CO_2·(g Ru)1·h-1, 3.1 times higher than that on Ru/Al_2O_3[0.19 mol CO_2·(gRu)-1·h-1]. The effect of TiO_2 content and TiO_2–Al_2O_3calcination temperature on catalytic performance was addressed. The corresponding structures of each catalyst were characterized by means of H_2-TPR, XRD, and TEM. Results indicated that the averaged particle size of the Ru on TiO_2–Al_2O_3support is 2.8 nm, smaller than that on Al_2O_3 support of 4.3 nm. Therefore, we conclude that the improved activity over Ru/TiO_2–Al_2O_3catalyst is originated from the smaller particle size of ruthenium resulting from a strong interaction between Ru and the rutile-TiO_2 support, which hindered the aggregation of Ru nanoparticles.     

The cooperation effect of Ni and Pt in the hydrogenation of acetic acid

The catalytic hydrogenation of carboxylic acid to alcohols is one of the important strategies for the conversion of biomass.Herein,a series of Ni-doped PtSn catalysts were prepared,characterized and studied in the hydrogenation of acetic acid.The Ni dopant has a strong interaction with Pt,which promotes the hydrogen adsorption,providing an activated hydrogen-rich environment for the hydrogenation.Meanwhile,the presence of Ni also improves the Pt dispersion,giving more accessible active sites for hydrogen activation.The cooperation of Pt and Ni significantly promotes the catalytic activity of the hydrogenation of acetic acid to ethanol.As a result,the catalyst with 0.1%Ni exhibits the best reaction activity,and its space time yield is twice as that of the PtSn/SiO2 catalyst.It provides a meaningful instruction on the catalyst design for the carboxylic acid hydrogenation.     

超临界氨合成

Ammonia synthesis at supercritical conditions was first studied over iron and active carbonsupported ruthenium catalysts in a fixed-bed reactor. The influences of 15 kinds of different supercritical media, such as alkanes of C7-C13, 1, 2, 3, 4-tetrahydronaphthalene, cis-decalin, o-xylene,ethylbenzene, quinolin, n-hexane and aniline etc. and reaction conditions (catalyst, temperature, space velocity, particial pressure of media) on ammonia at supercritical condition were investigated.Supercritical medium was decomposed under reaction conditions over Fe and Ru/AC catalysts. The decomposition products deactivated the catalysts. Alkane decomposed the least, and the rate of deactivation was the slowest. Therefore alklane was a relatively good medium. The decomposion of supercritical medium was the key for the deactivation of catalysts. Another important reason for the decrease of ammonia concentration was that the effective pressure of syngas decreased because of the presence of supercritical media. The active temperature of catalyst was the decisive factor in supercritical ammonia synthesis. Supercritical catalytic reaction was viable only at a lower temperature. Ammonia ynthesis at supercritical conditions is possible if a catalyst with active temperature lower than 573 K could e developed and the decomposition of supercritical media could be prevented.     

The effect of copper valence on catalytic combustion of styrene over the copper based catalysts in the absence and presence of water vapor☆

Catalysts Cu Ox/γ-Al_2O_3-IH and Cu Ox/γ-Al_2O_3-IM were prepared, characterized, and tested for styrene combustion in the absence and presence of water vapor. The effect of copper valence of the catalysts on the catalytic activity for styrene combustion was discussed using the theory of hard soft acids and bases(HSAB).The results showed that the existence of water vapor in feed stream inhibited the catalytic activity for styrene combustion due to the competition adsorption of water molecule. HSAB theory confirmed that the local soft acidity of the catalyst Cu Ox/γ-Al_2O_3-IH was much stronger than that of the catalyst Cu Ox/γ-Al_2O_3-IM because of the higher content of soft acid Cu+on its surface, which increased the adsorption ability toward soft base of styrene and reduced the adsorption toward hard base of water vapor, and thus increased the catalytic activity for styrene combustion and weakened the negative influence of water vapor.     

液相合成甲醇催化剂活性的研究

The effects of reduction procedure, reaction temperature and composition of feed gas on the activity of a CuO-ZnO-Al2O3 catalyst for liquid phase methanol synthesis were studied. An optimized procedure different from conventional ones was developed to obtain higher activity and better stability of the catalyst. Both CO and CO2 in the feed gas were found to be necessary to maintain the activity of catalyst in the synthesis process. Reaction temperature was limited up to 523K, otherwise the catalyst will be deactivated rapidly. Experimental results show that the catalyst deactivation is caused by sintering and fouling, and the effects of CO and CO2 on the catalyst activity are also investigated. The experimental results indicate that the formation of water in the methanol synthesis is negligible when the feed gas contains both CO and CO2. The mechanism for liquid-phase methanol synthesis was discussed and it differed slightly from that for gas-phase synthesis.     

Pt／C催化邻硝基氯苯加氢反应的动力学研究

The kinetics of catalytic hydrogenation of ortho-nitrochlorobenzene to 2,2‘-dichloroazoxybenzene on platinum/carbon catalyst is investigated in a slurry reactor with the temperature range of 313--343 K, and orthochloroaniline is formed as a byproduct. Models based on Rideal-Eley and Langmuir-Hinshelwood mechanism have been proposed based on the rate data and the kinetic regime. The former model can be used to fit the experimental data better. Reaction controlling steps are physical adsorption of hydrogen and adsorbed ortho-nitrochlorobenzene reacted on the surface of catalyst.     

Kinetics of Ortho-nitrochlorobenzene Hydrogenation on Platinum/Carbon Catalyst

The kinetics of catalytic hydrogenation of ortho-nitrochlorobenzene to 2,2'-dichloroazoxybenzene on platinum/carbon catalyst is investigated in a slurry reactor with the temperature range of 313-343 K, and ortho-chloroaniline is formed as a byproduct. Models based on Rideal-Eley and Langmuir-Hinshelwood mechanism have been proposed based on the rate data and the kinetic regime. The former model can be used to fit the experimental data better. Reaction controlling steps are physical adsorption of hydrogen and adsorbed ortho-nitrochlorobenzene reacted on the surface of catalyst.     

三相体系中TS-1分子筛催化环己酮氨肟化制环己酮肟(英文)

An innovative green process of producing ε-caprolactam was proposed by integrating ammoximation and Beckmann rearrangement effectively. As a first part of the new process, TS-1 molecular sieve-catalyzed synthesis of cyclohexanone oxime from cyclohexanone, ammonia and hydrogen peroxide was carried out in a batch plant. Cyclohexane was used as the solvent in the three-phase reaction system. The influences of essential process parameters on ammoximation were investigated. Under the reaction conditions as catalyst content of 2.5% (by mass); H 2 O 2 /yclohexanone molar ratio of 1.10; NH 3 /cyclohexanone molar ratio of 2.20; reaction temperature of 343 K; reaction time of 5 h, high conversion of cyclohexanone and selectivity to oxime (both>99%) were obtained. Thus, the three-phase ammoximation process showed equal catalytic activity as TS-1 but much more convenient and simpler for the separation of catalyst in comparison to the industrial two-phase system with t-butanol used as solvent.     

Carbon-supported Ru catalyst with lithium promoter for ammonia synthesis

The electronegativity of Li is much higher than that of Na or K, but the ammonia synthesis activities of Li-promoted Ru/AC catalysts were comparable to the values of Ru catalyst promoted with K, which were much higher than those over Ru catalyst with Na promoter. The presence of Li increased the catalytic activity by changing the chemisorption properties such as hydrogen adsorption and nitrogen adsorption for carbon-supported Ru catalysts, rather than affecting the sizes of Ru particles or the electron density of Ru metal.     

Influence of Citric Acid on Size Distribution of Ru Particles and the Catalytic Activities of the Ru/AC Catalysts

Citric acid (CA) was used to modify graphited activated carbon (AC) for improving size distribution of Ru particles and catalytic activity of the Ru/AC catalyst. The influence of CA on the texture of AC and Ru/AC, Ru distribution and catalytic activity were investigated. TEM, TGA, TPD-MS, CO pulse chemisorption and N₂ physisorption indicate that CA modified AC creates more functional groups and thus more homogeneous dispersion of Ru nanoparticles. TEM images show most of the Ru particles were ca. 2–2.5 nm for the CA4 + Ru4/AC catalyst. The increase of ammonia synthesis activity for Ru–Ba–K/AC catalyst is more than 16% when the content of CA in AC is 4 wt.% at 673 K and 10,000 h^?1.     

助剂对活性炭负载钴催化剂氨合成活性的影响

采用四槽高压连续流动反应器研究了添加助剂Ba、K和Sm对活性炭负载钴催化剂氨合成活性的影响,结果发现,添加助剂Ba、K和Sm可以提高催化剂的氨合成活性,其中,Ba的促进效果最好,Ba与Co物质的量比为0.3时,催化活性最高。在Ba-Co/AC催化剂中,助剂Sm的加入降低了催化剂的氨合成活性,而少量K助剂(K与Co物质的量比为0.25～0.5)可以提高其催化性能,在10 MPa、10 000 h^-1和450 ℃条件下,双助剂催化剂的氨合成活性可达120 mmol·(g·h）^-1,进一步增加K的量,其氨合成活性下降。     

助剂对钌基氨合成催化剂活性的作用研究

利用等体积浸渍法制备了活性炭负载钌基氨合成催化剂,考察了助剂Ba、K、Sm对催化活性的影响,探讨了其改善活性的调变规律。用TPD技术研究了氮在系列催化剂上的脱附行为。研究结果表明,助剂Ba、K、Sm的加入显著地提高了催化剂的活性,多助剂催化剂的活性明显优于单助剂催化剂。稀土金属氧化物Sm2O3除具有助催作用外,还有助于催化剂的热稳定性及钌的分散。在钌基氨合成催化反应中,N2 分子的活化离解是速控步骤。氮的脱附活化能愈低,催化活性愈高,其脱附活化能次序为Ru>Ru-Sm>Ru-K>Ru-Ba>Ru-Sm-K>Ru-Sm-Ba>Ru-Ba-K>Ru-Sm-Ba-K。     

氨合成钌基催化剂的研究进展

近年来,钌基氨合成催化剂因其高活性、高稳定性和反应条件温和成为研究热点。综述国内外氨合成钌基催化剂的研究进展,重点介绍钌基催化剂载体、助剂和前驱体对氨合成反应性能的影响。石墨化程度高、导电性能良好的碳载体或氧化物与碳的复合载体是氨合成反应的良好载体;碱金属和碱土金属类助剂通过改变活性金属表面静电场,起到电子助剂的作用,并且碱土金属对反应的促进作用优于碱金属,稀土金属Sm能够抑制碳载体的甲烷化反应;与Ru Cl3相比,Ru3(CO)12是氨合成反应的理想前驱体。简介以电子化合物为载体的钌基氨合成体系,负载钌的高比表面积电子化合物C12A7:e-是强大的电子供体,能够提高氮气在钌上的解离程度,并能可逆地储存氢,有效抑制氢吸附对钌表面的毒害,从而大大提高氨合成反应活性。进一步开发温和条件下非贵金属高效氨合成催化剂将具有重要的理论和现实意义。     

以RuCl3为前驱体的无氯Ru/Al2O3氨合成催化剂的制备

用等体积浸渍法制备了一种以RuCl₃作为钌母体，分别以γ-Al₂O₃和δ,θ-Al₂O₃为载体的负载型无氯Ru/Al₂O₃氨合成催化剂。该催化剂用水合肼还原，以Sm(NO)₃和Ba(NO₃)₂作助剂。催化剂各组分n(Ru)∶n(Ba)∶n(Sm)=1∶0.55∶1.6。用N₂物理吸附、XRD、XRF和CO化学吸附等方法对载体和催化剂进行表征。结果表明，以δ,θ-Al₂O₃为载体的催化剂，其氨合成活性高于以γ-Al₂O₃为载体的催化剂的活性；用水合肼还原并用热碱液和纯水洗涤的催化剂不残留Cl^-，Ru金属分散度高，其氨合成活性与用无氯钌前驱体制备并用H2还原的催化剂的活性相当，在压力10.0 MPa，空速10 000 h^-1的反应条件下，475 ℃转化率为81.2%，在500 ℃时转化率可以达到100%。而用H₂还原以RuCl₃作为钌母体的Ru/Al₂O₃催化剂时，因还原后催化剂上有Cl^-残留，其催化活性较低。     

活性炭负载钌催化剂上氨合成反应动力学研究

在固定床反应器中对Ba-Ru-K/AC催化剂在相应的工业条件下［温度(350~450) ℃,压力10 MPa,V(H₂)∶V(N₂)=1.0、1.5、2.0、2.5和3.0,空速(60 000~180 000) h^－1］,进行了系列动力学测试。采用改进的Temkin动力学方程对实验数据进行拟合,考虑到H₂和NH₃的吸附对催化剂作用的阻碍效应,优化得到动力学模型参数n、α、w₁和w₂分别为1、0.15、0.5和1.4。结果表明,在Temkin方程中加入H₂和NH₃的吸附项能够获得可靠的动力学模型,用Arrhenius和Van’t Hoff方程对动力学和热力学参数k、K_H2和K_NH3进行线性拟合,得到氨合成反应的活化能为90.2 kJ·mol^－1,远低于铁基催化剂,说明Ru上N₂的解离吸附活化能垒远低于传统磁铁矿基催化剂和维氏体基催化剂。H₂的吸附热为76.2 kJ·mol^－1,证明Ba-Ru-K/AC催化剂上H₂的吸附较强烈,对N₂的吸附有强烈的抑制作用。改进的Temkin动力学方程能应用于使用Ru/C催化剂的氨合成反应器的设计和操作。     

沉淀剂对Ru/MgO-CeO2氨合成催化剂催化性能的影响

以K<,2>RuO<,4>为钌前驱体,通过共沉淀法制备了Ru/MgO-CeO<,2>氨合成催化剂.考察了5种不同沉淀剂对Ru/MgO-CeO<,2>催化剂的结构和性能的影响,并运用X射线衍射(XRD)、CO吸附、N<,2>物理吸附和H<,2>程序升温还原(H<,2>-TPR)等技术对催化剂进行了表征,讨论了沉淀剂对氨合...     

表面活性剂辅助溶胶-凝胶法制备掺Ba纳米MgO及其负载钌基氨合成催化剂

在表面活性剂聚乙二醇（PEG）、聚丙烯酸钠（PAAS）、聚乙烯醇（PVA）的辅助下,采用溶胶-凝胶法制备了一系列掺Ba纳米MgO及其负载的氨合成Ru催化剂。并采用场发射扫描电镜、X射线粉末衍射、N2物理吸附-脱附、X射线能谱仪对样品进行表征。结果表明：表面活性剂的添加可改善掺Ba纳米MgO的织构性质和表面性质,并增强钡、镁之间的相互作用,促使了钡在载体中的分散。其中,在10 MPa、425 ℃、10000 h－1的测试条件下,添加5%的PAAS时制得的2%Ru/Ba-MgO催化剂出口氨生成速率达65.9 mmol/(g?h)。