Preparation and luminescent properties of YVO4:Eu3+ nanofibers by electrospinning

This paper describes a procedure based on electrospinning for generating europium-doped yttrium vanadate (YVO4:Eu3+) nanofibers with diameters ranging from 30 to 50 nm. The YVO4:Eu3+ nanofibers were obtained through calcining precursory nanofibers, which were prepared through the electrospinning method. Suitable electrospinning parameters, such as concentration of PVP in solution, spinneret tip-to-collector plate distance (TCD), and applied voltage between spinneret and collector plate, are used to obtain thinner and more uniform precursory nanofibers of YVO4:Eu3+, which is important for preparing smaller diameter pure YVO4:Eu3+ nanofibers. The luminescent properties of the YVO4:Eu3+ nanofibers including excitation and emission spectra and fluorescence lifetime were studied. The excitation spectrum shows a broad band extending from 200 to 350 nm, which corresponds to the strong vanadate absorption in YVO4:Eu3+. The emission spectrum is dominated by the red 5D0 --> 7F2 hypersensitive transition of Eu3+. The fluorescence lifetime of Eu3+ 5D0 --> 7F2 (619 nm) is determined to be 493 micros at room temperature, which is basically in accordance with that in the bulk (521 micros).     

Characterization and luminescence of Eu3+ ions doped 12CaO 7Al2O3 nanopowders

Eu3+ ions doped 12CaO 7Al2O3 (C12A7) powders with different Eu3+ concentrations were prepared by sol-gel combined with solid state reaction method. The results of XRD and Raman spectra showed that single cubic phase polycrystalline C12A7:Eu3+ powders were prepared. The absorption peaks attributed to f-f transition of Eu3+ ion can be observed, indicating that Eu3+ had been incorporated into C12A7 lattice site. Visible PL peaks around 578, 588, 614 nm were ascribed to 5D0 --> 7FJ (J = 0, 1, 2) transitions of Eu3+ under the excitation of 488 nm line. The PL of C12A7:Eu3+ showed the strongest emission intensity at Eu3+ concentration of 0.5 at%. Two different types of Eu3+ centers were identified by the two lines from 5D0 --> 7F0 transition emission. The doping mechanism of C12A7:Eu3+ might be attributed to Eu3+ ions substitution for two types of Ca2+ lattice sites in C12A7. The temperature dependent PL spectra of Eu-doped C12A7 were measured in the range from 100 to 300 K under the excitation of 488 nm laser line. The PL intensities as a function of temperature were well fitted by using a unified theoretical model, considering thermal activation and nonradiative energy transfer processes.     

Spherical SiO2 @ GdPO4: Eu3+ core-shell phosphors: sol-gel synthesis and characterization

Nanocrystalline GdPO4 : Eu3+ phosphor layers were coated on non-aggregated, monodisperse and spherical SiO2 particles by Pechini sol-gel method, resulting in the formation of core-shell structured SiO2 @ GdPO4 : Eu3+ particles. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), photoluminescence (PL), low-voltage cathodoluminescence (CL), time-resolved PL spectra and lifetimes were used to characterize the core-shell structured materials. Both XRD and FT-IR results indicate that GdPO4 layers have been successfully coated on the SiO2 particles, which can be further verified by the images of FESEM and TEM. Under UV light excitation, the SiO2 @ GdPO4 : Eu3+ phosphors show orange-red luminescence with Eu3+ 5D0-7F1 (593 nm) as the most prominent group. The PL excitation and emission spectra suggest that an energy transfer occurs from Gd3+ to Eu3+ in SiO2 @ GdPO4 : Eu3+ phosphors. The obtained core-shell phosphors have potential applications in FED and PDP devices.     

Investigation of Eu-doped mesoporous titania phosphor with enhanced luminescence

A novel mesoporous TiO2 phosphor doped with Eu was synthesized through a facile hydrothermal synthesis method using cetyltrimethylammonium bromide as structure template reagent. The samples were characterized by X-ray diffraction, N2 adsorption-desorption, scanning electron microscope, high-resolution transmission electron microscopy, ultraviolet visible diffuse reflectance, X-ray photoelectron spectroscopy, and three dimensional Photoluminescence. The X-ray diffraction results demonstrated that the products were anatase type with polycrystalline. N2 adsorption-desorption analysis showed that the samples were of high ordered double mesoporous structures. Eu-doped mesoporous TiO2 indicated the typical fluorescent spectra of Eu3+ ion occurred: the excited-states at 5L6 (394 nm), 5D2 (465 nm) and 5D1 (535 nm); the main emission peaks at 592 and 617 nm, corresponding with the transitions 5D0 --> 7F1 and 5D0 --> 7F2, respectively. Meanwhile, the phenomena of Eu(3+)-doped mesoporous TiO2 phosphor with efficient nonradiative energy transfer from the mesoporous TiO2 host to the activator Eu3+ ions was observed and possible emission mechanism was proposed. High dispersion of Eu in mesoporous TiO2 matrix was responsible for enhanced luminescence.     

Hydrothermal synthesis and size-enhanced chromaticity of Sr2ZnSi2O7:Eu3+ nanoparticles

Red phosphor Sr2ZnSi2O7:Eu3+ nanoparticles with an average diameter of 20 nm were successfully synthesized via a low-temperature hydrothermal route in order to understand the underlying relationship between size and luminescent properties. The nanometer-sized particles result in a distinct improvement in chromaticity and a high quenching concentration. According to emission spectra, the relative intensity of the 5D0 --> 7F2 to 5D0 --> 7F1 transitions in nanometer-sized phosphors is higher than that of the corresponding bulk material. The better chromaticity results from the more distorted lattices and relatively lower crystal symmetry around the Eu3+ ions, which is ascribed to the large surface area due to the nanometer size of the phosphor. Moreover, the nanometer-sized Sr2ZnSi2O7:Eu3+ red phosphor exhibits a shorter fluorescent lifetime and a blue-shift in excitation spectra compared to that of its bulk counterpart. These results indicate that size-induced enhancement of luminescent properties is an efficient way to obtain red phosphors with better chromaticity.     

Nanostructured CaWO4, CaWO4:Eu3+ and CaWO4:Tb3+ particles: sonochemical synthesis and luminescent properties

Nanostructured CaWO4, CaWO4:Eu3+, and CaWO4:Tb3+ phosphor particles were synthesized via a facile sonochemical route. X-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, transmission electron microscopy, photoluminescence, low voltage cathodoluminescence spectra, and photoluminescence lifetimes were used to characterize the as-obtained samples. The X-ray diffraction results indicate that the samples are well crystallized with the scheelite structure of CaWO4. The transmission electron microscopy and field emission scanning electron microscopy images illustrate that the powders consist of spherical particles with sizes from 120 to 160 nm, which are the aggregates of even smaller nanoparticles ranging from 10 to 20 nm. Under UV light or electron beam excitation, the CaWO4 powder exhibited a blue emission band with a maximum at 430 nm originating from the WO4/2- groups, while the CaWO4:Eu3+ powder showed red emission dominated by 613 nm ascribed to the 5D0 --> 7F2 of Eu3+, and the CaWO4:Tb3+ powders showed emission at 544 nm, ascribed to the 5D4 --> 7F5 transition of Tb3+. The PL excitation and emission spectra suggest that the energy is transferred from WO4/2- to Eu3+ CaWO4:Eu3+ and to Tb3+ in CaWO4:Tb3+. Moreover, the energy transfer from WO4/2- to Tb3+ in CaWO4:Tb3+ is more efficient than that from WO4/2- to EU3+ in CaWO4:Eu3+. This novel and efficient pathway could open new opportunities for further investigating the novel properties of tungstate materials.     

Study on luminescent properties of Eu3+ doped Gd2WO6, Gd2W2O9 and Gd2(WO4)3 nanophosphors prepared by co-precipitation

Eu3+ doped Gd2WO6, Gd2W2O9 and Gd2(WO4)3 nanophosphors with different concentrations have been prepared by co-precipitation. XRD (X-ray diffraction) and SEM (scanning electron microscopy) were used to investigate the structure and morphology. The emission spectra, excitation spectra and fluorescence decay curves were measured, and partial J-O parameters and quantum efficiencies of Eu3+ 5D0 energy level were calculated. Furthermore, concentration quenching curves of Eu3+ in different hosts were drawn. The photoluminescent properties of Eu3+ doped Gd2WO6, Gd2W2O9 and Gd2(WO4)3 nanophosphors have been studied. The results indicate that Eu3+ 5D0-7F2 red luminescence can be effectively excited by 395 nm and 465 nm in Gd2WO6 and Gd2W2O9 hosts, similar to the familiar Gd2(WO4)3:Eu. Especially Gd2W2O9:Eu has strong red emission and high quenching concentration, so it has potential applications for trichromatic white LED as red fluorescent materials.     

Synthesis and luminescence properties of Sr2SiO4: Eu3+, Dy3+ phosphors by the sol-gel method

The Sr2SiO4:Eu3+, Dy3+ phosphors for white light emitting diodes (LEDs) were synthesized by the sol-gel method. The microstructure and luminescent properties of the obtained Sr2SiO4:Eu3+, Dy3+ particles were well characterized. The results demonstrate that the Sr2SiO4:Eu3+, Dy3+ particles, which have spherical morphology, emitted an intensive white light emission under excitation at 386 nm. The phosphors show three emission peaks: the blue emission at 486 nm corresponding to the 4F(9/2)-6H(15/2) transition of Dy3+, the yellow emission at 575 nm corresponding to the 4F(9/2)-6H(13/2) transition of Dy3+, and the red emission at 615 nm corresponding to the 5D0-7F2 transition of Eu3+. At the same time, the effect of Eu3+ concentration on the emission intensities of Sr2SiO4:Eu3+, Dy3+ was investigated in detail. The phosphors used for white LEDs were obtained by combining near ultraviolet (NUV) light (386 nm) with Sr2SiO4:0.04Dy3+, 0.01Eu3+ phosphors with the characteristic of Commission Internationale de l'Eclairage (CIE) chromaticity coordinate (x, y) of (0.33, 0.34), and color temperature Tc of 5,603 K. In addition, the effect of the charge compensators (Li+, Na+, and K+ ions) on the photoluminescence (PL) emission intensities were studied.     

Observation of room-temperature 5D1 luminescence of an organoeuropium complex encapsulated in sol-gel glass

In comparing emissions of the inorganic Eu3+ salts (chloride or nitrate) to organoeuropium complexes doped into optically transparent sol-gel glass, previous studies have indicated that changes in the local chemical environment by chelation or variation of the ligand or gel matrix compositions were found to leave the main spectral features of Eu3+ essentially unchanged; complexation just increases the emission intensity of europium and leads to broadening and splitting of the peaks. In all cases studied and irrespective of the excitation energy, the observable emission peaks result only from relaxations out of the 5D0 excited state of Eu3+ to the first five levels of the 7F ground manifold. The present research examines the luminescence behavior of EuCl3 and Eu-TETA (TETA is the macro cycle, 1,4,8,11-tetraazacyclotetradecane-1,4,8,11-tetraaceticacid) doped into a sol-gel host; in addition to emissions from the 5D0, emission from the 5D1 excited state of Eu3+ is observed for the first time.     

Luminescence properties of nano-sized Sr2MgSiO5: Eu2+, Mn2+ phosphors prepared by the sol-gel method

Nano-sized Sr2MgSiO5:Eu2+, Mn2+ phosphor was synthesized by the sol-gel method. The preparation conditions of the precursor were determined. The effect of Eu2+ and Mn2+ content on the luminescence intensity was studied. X-ray diffraction (XRD), photoluminescence spectra (PL), and photoluminescence excitation spectra (PLE) were used to characterize the samples. The results showed that the excitation bands ranged from 250 to 450 nm, and their peaks positioned around 365 nm. The emission spectrum consists of three bands: blue, green, and red, respectively. The blue and green emission bands originate from the center of the Eu2+, while the red emission band is attributed to the energy transfer from Eu2+ to Mn2+. White light can be obtained by mixing the three emission colors. The experiment results show that the Sr2MgSiO5:Eu2+, Mn2+ is a single host phosphor with superior properties for use in white light emitting diodes (white LED).     

Sol-gel fabrication and photoluminescence properties of SiO2 @ Gd2O3:Eu3+ core-shell particles

A uniform nanolayer of europium-doped Gd2O3 was coated on the surface of preformed submicron silica spheres by a Pechini sol-gel process. The resulted SiO2 @ Gd2O3:Eu3+ core-shell structured phosphors were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays. The XRD results show that the Gd2O3:Eu3+ layers start to crystallize on the SiO2 spheres after annealing at 400 degrees C and the crystallinity increases with raising the annealing temperature. The core-shell phosphors possess perfect spherical shape with narrow size distribution (average size: 640 nm) and non-agglomeration. The thickness of the Gd2O3:Eu3+ shells on the SiO2 cores can be adjusted by changing the deposition cycles (70 nm for three deposition cycles). Under short UV excitation, the obtained SiO2@Gd2O3:Eu3+ particles show a strong red emission with 5D0-7F2 (610 nm) of Eu3+ as the most prominent group. The PL intensity of Eu3+ increases with increasing the annealing temperature and the number of coating cycles.     

Luminescent properties of La3PO7:Eu3+ nanoparticles

La3PO7:Eu3+ samples were prepared by combustion and annealing and characterized by X-ray diffraction and transmission electron microscopy. It was found that the average size of the particles is about 80 nm. The red emission from the 5D0 --> 7F2 transition of the Eu3+ ions under ultraviolet light excitation is much stronger than the orange emission from the 5D0 --> 7F1 transition. The emission spectra, charge transfer band, laser selective excitation spectra, and time-resolved spectra indicate that symmetry of the local environment of Eu3+ lacks an inversion center and Eu3+ ions occupy at least two types of sites in the La3PO7 crystal. The superior color chromaticity compared to other phosphates and borates doped with Eu3+ means La3PO7:Eu3+ may have potential as a luminescent material.     

Controllable morphology and high photoluminescence of (Y, Gd)(V, P) O4:Eu3+ nanophosphors synthesized by two-step reactions

Multi-ion doped YVO(4):Eu(3+) nanophosphors with high photoluminescence intensity were successfully prepared by a two-step reaction process for the first time, including YVO(4):Eu(3+) seeds synthesized by hydrothermal reaction and co-doping P(5+) and Gd(3+) in a sol-gel process. X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and photoluminescence spectroscopy were adopted to detect the structure, grain size, morphology and optical properties of the nanophosphors, respectively. Owning to the template-induced effect of the seeds, the morphology and size of the nanophosphors could be controlled by adjusting the molar ratios between the seeds and doping ions. The size of these nanophosphors increased as P(5+) and Gd(3+) co-doped. However, most of the samples kept approximately spherical morphology and narrow size distribution. The composition-optimized (Y, Gd)(V, P)O(4):Eu(3+) nanophosphors with spherical morphology in the 80-100 nm range exhibit better red emission and superior color saturation under vacuum ultraviolet excitation compared with that of the commercial phosphor (Y, Gd)BO(3):Eu(3+).     

Y2O2S:0.03Eu,0.03Ti的长余辉特性及Ti向Eu3+的余辉传能机制

采用高温还原法合成了Eu，Ti共激活橙红色Y2O2S长余辉发光材料，并测量了Y2O2S：0．03Eu,0．03Ti磷光体的荧光光谱，余辉分辨和余辉衰减曲线谱．实验结果表明，Y2O2S：0．03Eu,0．03Ti磷光体的发射谱由一系列Eu^3＋离子内部能级跃迁的尖峰组成；余辉分辨谱则不同，由一个主峰位于565nm的宽发射带和一系列波长范围位于500nm以上的窄发射带两种峰形组成，可分别归为Ti离子的宽带余辉发射和三价Eu^3＋的线状余辉发射,分析认为，样品中存在Ti余辉发射向Eu^3＋内部能级间产生选择性的余辉传能机制，从而导致Y2O2S：0．03Ti，0．03Eu磷光体中同时出现两种发光中心离子的余辉分辨谱现象．     

低温燃烧法合成γ-LiAlO2:Eu3+红色荧光粉及其发光性能

低温燃烧法合成了γ-LiAlO2:Eu3+红色荧光粉,采用XRD、SEM、PL对样品进行了结构、形貌及发光性能表征。结果表明样品为四方晶系结构,在395nm的紫外光激发下,样品发射峰位于578、588、613、651和700nm,对应Eu3+离子的5 D0→7FJ=0,1,2,3,4的能级跃迁,主峰位于613nm处。其发光强度与Eu3+和H3BO3的掺量密切相关。     

Study on luminescence behavior of BaAl12O19:Tb, Eu

BaAl12O19:Tb, Eu phosphors were prepared by sol-gel technique. The luminescence properties and the energy transfer between Eu2+ and Tb3+ were investigated. For BaAll2O19:Tb phosphor, the strongest excitation peak and emission peak produced from Tb3+ transition of 5D4-7F5 were at 240 nm and at 550 nm respectively, while the peak shape was narrow and peak intensity was large. The Eu2+ added in the BaAl12O19:Tb induced energy transfer to Tb3+ and different color luminescence from blue (400 nm) to green (570 nm) was obtained by changing the ratio of Tb3+/Eu2+ with excitation at 240 nm.     

Eu3+对Na3Gd2(BO3)3∶Tb3+发光性能的影响及其能量传递

采用高温固相法制备了Na_3Gd_2(BO_3)_3∶Tb~(3+),Eu~(3+)荧光粉,并对样品的物相组成、微观形貌、发光性能和能量传递进行了分析。结果表明,Na_3Gd_(2-x)(BO_3)_3∶xTb~(3+)荧光粉在紫外和近紫外区域有较强的激发峰,在368nm波长激发下,发射光呈绿色,Tb~(3+)最佳掺杂量为x=0.04。随着在Na_3Gd_(1.96)(BO_3)_3∶0.04Tb~(3+)中掺入Eu~(3+),Tb~(3+)对Eu~(3+)产生了以电偶极-电偶极相互作用为主的能量传递,且传递效率随Eu~(3+)掺杂量的增加而逐渐增大。发射光谱中Tb~(3+)的发射峰强度逐渐减弱,而Eu~(3+)的发射峰强度逐渐增强,导致Na_3Gd_(1.96-y)(BO_3)_3∶0.04Tb~(3+),yEu~(3+)荧光粉发光颜色由绿色向橙色变化。     

高温固相法制备CaCO_3:Eu~(3+),Li~+红色荧光粉

以CaCO3、Eu2O3和Li2CO3为主要原料,采用高温固相法,首次制备CaCO3:Eu3+,Li+红色荧光粉。通过对前驱物进行同步差热分析(TG-SDTA),确定其煅烧温度;利用X射线衍射(XRD)、傅立叶变换红外光谱(FT-IR)和拉曼光谱对样品的结构进行表征;采用荧光光度仪对样品的发光性能进行测试。结果表明:前驱物的煅烧温度为655℃时,样品主晶相为方解石型CaCO3,掺杂Eu3+和Li+离子分别作为发光中心和敏化剂进入到CaCO3的晶格中。荧光粉的最大激发峰位于272nm,属于紫外激发,最大发射峰位于608nm附近,对应于Eu3+离子的5d0→7f2跃迁,并且Eu3+离子在CaCO3基质中处于偏离或无反演对称中心的格位上。     

Eu3+掺杂的硼酸锶系列荧光体的合成及其发光性能

采用溶胶-凝胶法和高温固相反应法合成了Eu^3 掺杂的SrB4O7、SrB2O4、Sr2B2O5、Sr3B2O6荧光体．荧光光谱测试结果表明在不同基质中Eu^3 的荧光发射是有区别的，Sr2B2O5：Eu^3 、Sr3B2O7：Eu^3 发射峰在610nm左右的红光区，SrB2O4：Eu^3 的发射峰在593nm的橙色区，而SrB4O7：Eu^3 则表现出了Eu^2 离子的特征峰，产生这种区别主要是由Eu^3 所处的配位环境不同造成的．荧光体SrB4O7：Eu^3 、SrB2O4：Eu^3 、Sr2B2O5：Eu^3 、Sr3B2O6：Eu^3 的最佳掺杂浓度为2％左右．     

Selective and controlled synthesis of multiform morphologies Y2O3:Eu3+ and luminescence properties

Uniform Y2O3 nanorods, nanosheets, nanotubes and nanoshperes were controllably synthesized via an urea-based homogeneous precipitation and hydrothermal synthesis through choosing appropriate yttrium sources, the water/ethanol ratio of mixed solvents and precipitators. The nanopheres and nanotubes were obtained through homogeneous precipitation method using soluble yttrium nitrate as the yttrium source. The nanosheets and nanorods were obtained via a facile hydrothermal synthetic method using yttrium chloride and yttrium acetate as the yttrium source. During these experiments Urea and NaOH were used as precipitators and added in correct order. We also studied the spectroscopic properties of Y2O3:Eu3+ phosphor. The Eu3+ ion mainly shows its characteristic red (611 nm, 5D0 --> 7F2) emissions in all kinds of morphologies Y2O3:Eu3+ phosphor, but emission intensity are different. It can be explain from the viewpoint of their different absorption properties closely related to their micro-morphologies.