A modified hot processing strategy for beef: effects on fresh meat quality

A modified hot processing (MHP) strategy for beef carcasses using known chilling technology to maintain quality in the higher priced cuts while retaining lower value cuts for further, immediate hot processing was evaluated. Following high voltage electrical stimulation, paired sides from 36 carcasses were either conventionally processed (CP) or reduced in a manner similar to the French pan traité cut. The sides were help in a pre-chiller for 1 h prior to blast chilling at −20°C for 3 h at an air speed of 2·3 m s⁻¹, followed by chilling at 2°C for the remainder of the 24 h period. Overall, MHP of beef carcass sides had minimal effects on fresh meat quality in the longissimus thoracis et lumborum (LTL) and the semimembranosus (SM) muscles despite removing over 50% of the carcass side weight in the form of lower value cuts. Sarcomere length was significantly shorter (P ≤ 0·05) in the anterior (AL) and posterior (PL) LTL which was attributed to the removal of skeletal restraint and carcass weight. The increase in shear value in the AL, location of MHP sides although statistically significant (P ≤ 0·05) would not likely be percieved by consumers. Hence a non-traditional method of processing carcasses by treating low value and high value primal cuts separately, may be viable.     

Conventional freezing plus high pressure-low temperature treatment: Physical properties, microbial quality and storage stability of beef meat

Meat high-hydrostatic pressure treatment causes severe decolouration, preventing its commercialisation due to consumer rejection. Novel procedures involving product freezing plus low-temperature pressure processing are here investigated. Room temperature (20 °C) pressurisation (650 MPa/10 min) and air blast freezing (−30 °C) are compared to air blast freezing plus high pressure at subzero temperature (−35 °C) in terms of drip loss, expressible moisture, shear force, colour, microbial quality and storage stability of fresh and salt-added beef samples (Longissimus dorsi muscle). The latter treatment induced solid water transitions among ice phases. Fresh beef high pressure treatment (650 MPa/20 °C/10 min) increased significantly expressible moisture while it decreased in pressurised (650 MPa/−35 °C/10 min) frozen beef. Salt addition reduced high pressure-induced water loss. Treatments studied did not change fresh or salt-added samples shear force. Frozen beef pressurised at low temperature showed L, a and b values after thawing close to fresh samples. However, these samples in frozen state, presented chromatic parameters similar to unfrozen beef pressurised at room temperature. Apparently, freezing protects meat against pressure colour deterioration, fresh colour being recovered after thawing. High pressure processing (20 °C or −35 °C) was very effective reducing aerobic total (2-log₁₀ cycles) and lactic acid bacteria counts (2.4-log₁₀ cycles), in fresh and salt-added samples. Frozen + pressurised beef stored at −18 °C during 45 days recovered its original colour after thawing, similarly to just-treated samples while their counts remain below detection limits during storage.     

Alternative pre-rigor foreshank positioning can improve beef shoulder muscle tenderness

Thirty beef carcasses were harvested and the foreshank of each side was independently positioned (cranial, natural, parallel, or caudal) 1 h post-mortem to determine the effect of foreshank angle at rigor mortis on the sarcomere length and tenderness of six beef shoulder muscles. The infraspinatus (IS), pectoralis profundus (PP), serratus ventralis (SV), supraspinatus (SS), teres major (TM) and triceps brachii (TB) were excised 48 h post-mortem for Warner–Bratzler shear force (WBSF) and sarcomere length evaluations. All muscles except the SS had altered (P < 0.05) sarcomere lengths between positions; the cranial position resulted in the longest sarcomeres for the SV and TB muscles whilst the natural position had longer sarcomeres for the PP and TM muscles. The SV from the cranial position had lower (P < 0.05) shear than the caudal position and TB from the natural position had lower (P < 0.05) shear than the parallel or caudal positions. Sarcomere length was moderately correlated (r = − 0.63; P < 0.01) to shear force.     

牛肉干生产工艺的研究

通过对牛肉干传统生产工艺及其它工艺的研讨。提出了新的牛肉干生产加工工艺方法——利用注射、滚揉、烘烤、蒸煮、切片或切条、二次烘干、调味等手段来生产牛肉干产品。该工艺设备简单。易于扩大生产而且产品口感好、卫生方便。     

Cholesterol photosensitised oxidation of beef meat under standard and modified atmosphere at retail conditions

The effect of the fluorescent light exposure and type of packaging (normal atmosphere and oxygen-rich atmosphere) was evaluated on the oxidation parameters (peroxides and cholesterol oxidation products) of raw beef slices placed in packed vessels and refrigerated. The concentration of COPs in meat treated under modified atmosphere ranged from 0.15 to 0.52mg/100g meat (average value of 0.27mg COPs/100g meat), which was twice as much as the average COPs content (0.14mg/100g) of meat packed under air (0.04-0.27mg COPs/100g meat). The main cholesterol oxide was 7k, which represented about one third of the total cholesterol oxides, followed by 7β-OH (20-25% of total COPs), 7α-OH (about 20%) and β-epoxy (12-18%). In normal atmosphere, photoxidation was a superficial process, since an inverse correlation between meat slice weight and COPs content on a lipid basis was observed, unlike in a high oxygen (32%) atmosphere.     

Effect of gamma-ray irradiation on the fatty acid profile of irradiated beef meat

The effect of γ-ray irradiation on the fatty acid profile of beef meat was examined at doses of 2.5, 5.0, 7.5, 10.0 and 15.0 kGy by means of ¹H NMR spectroscopy. NMR results revealed a clear trend toward an increase in the amount of saturated fatty acids and a decrease in the amount of polyunsaturated fatty acids in the triacylglycerol composition of the irradiated samples compared to the unirradiated sample with increasing the irradiation dose.     

Comparison of fresh beef and camel meat proteolysis during cold storage

The objective of this research was to determine the difference in myofibrillar fragmentation of camel meat and beef during postmortem aging. Semitendinosus muscle was excised at slaughter and muscle pH was measured at 6, 12, 24, 48, and 72h postmortem. Myofibril fragmentation index was measured on 1, 3, 5, and 7 days postmortem. Also, myofibrils isolated from semitendinosus muscles of camel and cattle at 1, 3, 5 and 7 days postmortem storage were analyzed using sodium dodecyl sulfate (SDS)-polyacrylamide gel electrophoresis. Results showed that the camel semitendinosus muscle had significantly higher myofibril degradation values compared to that in beef which was supported by a difference in troponin-T degradation and appearance of a 30kDa band. Postmortem pH decline of camel meat was significantly slower than that of beef. This study demonstrated that the semitendinosus protease activity of camel meat was superior to that of beef, which may have been due to the difference in pH decline.     

Theoretical analysis of two hot water cabinet systems for decontamination of sides of beef

The theory underlying the use of hot water to reduce the numbers of microbial contaminants of public health significance on freshly slaughtered animals was investigated. An analysis of steady-state predictions of microbial reductions and accompanying evaporative heat and mass losses in a hot water cabinet for the decontamination of beef sides is developed, based on published correlations. This is more comprehensive than previously undertaken and is used to compare two methods of contacting hot water with the sides of beef: conventional pressure sprays and an alternative, overhead distributor or 'deluge' system. Predictions indicate that a distributor cabinet does not need doors or thermal insulation, and highlight the potential economy and practical advantages over conventional spraying.     

Review: Automation and meat quality-global challenges.

The global meat industry has seen significant changes in the methods used to harvest and process fresh meat over the past century. Increased use of automation has led to significant increases in line speed for beef, pork, sheep, poultry and fish operations. For example, currently the fastest line observed has been broilers at 13,500/h. Such developments have required in-depth understanding of the pre and post rigor processes to prevent defects. Procedures such as maturation chilling and electrical stimulation are now common in red meat and poultry processing; allowing shorter time to deboning, while harvesting high quality meat. Robots designed to cut meat are also appearing on the market, and replacing traditional manual operations. This is a challenge, because high speed equipment is not necessarily sensitive to variations in size/quality issues, and requires development of unique sensors and control systems. Also, progress in breeding and genetics is contributing to greater product uniformity and quality; helping in operating automated equipment.     

A spectrophotometric method for the detection of carboxymyoglobin in beef drip

A spectrophotometric method, based on the electronic absorption and second‐derivative spectra of beef drip, has been developed to detect the amount of carbon monoxide bound to myoglobin in treated beef samples. The method has been validated following the criteria reported in the Eurachem guides. The limit of detection, equal to 0.14 μm , has been evaluated analysing ten blank samples, taking into account the mean concentration and the resulting standard deviations. The accuracy of the method has been studied in terms of trueness and precision; the first is expressed as per cent recovery (always exceeding 90%) and the second as relative standard deviation. The method is easy, rapid and allows one to determine qualitatively and quantitatively the CO concentration in the meat drip, by simply measuring in the UV–Vis spectrum of an unknown sample the absorbance values at three specific wavelengths: 423, 429 and 434 nm.     

Functionality of cow beef in coarse and fine ground model systems

Patties and sausage batters were made from trimmed brisket, chuck, striploin, hindshank, silverside, thick flank and rib trim from grass-fed Friesian cows. Functionality of each meat cut was determined from cook yield and true stress and strain of cooked sausage batters and cook yield, dimensional changes and peak force of cooked patties. Colour of raw and cooked slices from the meat cuts and cooked batters was evaluated using a colorimeter and a consumer panel. Composition of raw meat from all cuts was similar; chuck and rib trim had higher pH values and were more red than meat from other cuts. Cooked batters from striploin, chuck and hindshank had higher stress and strain values than gels from other cuts. Patties made from thick flank and striploin were the softest and had the highest cook yield. Batters and patties made from meat with higher salt soluble protein content retained more water and fat on cooking, were more cohesive and had higher bind strengths. Manufacturers can use functionality characteristics to select meat for specific products.     

A laboratory evaluation of a novel hot water cabinet for the decontamination of sides of beef

A hot water cabinet based on an idealized distributor design for the decontamination of sides of beef is described and a laboratory evaluation of this novel cabinet is reported.
Beef sides were inoculated with E. coli and exposed to mean water temperatures at the surface tissue ( T _f) of 83.5, 74.2, 66.0 and 44.5°C for 10 or 20 s. Mean log₁₀ reductions of bacteria for 10-s exposures were 2.23, 1.40, 0.91 and 0.2. For 20 s, reductions were 2.98, 2.14, 1.17 and 0.1. There was a significant ( P < 0.05) linear relationship between log reductions and T _f which varied with exposure time. At a T _f of 83.5°C with exposure times greater than 20 s, carcass bloom was judged to be permanently and adversely affected. At shorter times or with lower temperatures this did not occur.
Evaporative heat losses were well correlated with the pressure driving force ( r = 0.89) and gravity driving force ( r = 0.92) for air interchange between the cabinet and its surrounds.
The running cost using the distributor cabinet was one-third of that of an existing spray cabinet when compared at the maximum reduction of log 1.3 (95%) achieved by the spray cabinet. An additional advantage of the distributor cabinet is its constructional simplicity.     

Innovations in beef production systems that enhance the nutritional and health value of beef lipids and their relationship with meat quality

Consumers are becoming more aware of the relationships between diet and health and this has increased consumer interest in the nutritional value of foods. This is impacting on the demand for foods which contain functional components that play important roles in health maintenance and disease prevention. For beef, much attention has been given to lipids. This paper reviews strategies for increasing the content of beneficial omega-3 polyunsaturated fatty acids (PUFA) and conjugated linoleic acid (CLA) and reducing saturated fatty acids (SFA) in beef. Particular attention is given to intramuscular fat (IMF) and the relationships between fatty acid composition and key meat quality parameters including colour shelf life and sensory attributes. Despite the high levels of ruminal biohydrogenation of dietary PUFA, nutrition is the major route for increasing the content of beneficial fatty acids in beef. Feeding grass or concentrates containing linseed (rich in α-linolenic acid, 18:3n-3) in the diet increases the content of 18:3n-3 and its longer chain derivative eicosapentaenoic acid (EPA, 20:5n-3) in beef muscle and adipose tissue, resulting in a lower n-6:n-3 ratio. Grass feeding also increases docasahexaenoic acid (DHA, 22:6n-3). Feeding PUFA rich lipids which are protected from ruminal biohydrogenation result in further enhancement of the PUFA in meat with concomitant beneficial improvements in the ratio of polyunsaturated:saturated fatty acids (P:S ratio) and n-6:n-3 ratio. The main CLA isomer in beef is CLA cis-9, trans-11 and it is mainly associated with the triacylglycerol lipid fraction and therefore is positively correlated with level of fatness. The level of CLA cis-9, trans-11 in beef is related to (1) the amount of this isomer produced in the rumen and (2) synthesis in the tissue, by delta-9 desaturase, from ruminally produced trans vaccenic acid (18:1 trans-11; TVA). Feeding PUFA-rich diets increases the content of CLA cis-9, trans-11 in beef. Trans-fatty acids in foods are of rising importance and knowledge of the differential effects of the individual trans isomers is increasing. TVA is the major trans 18:1 isomer in beef and as the precursor for tissue CLA in both animals and man should be considered as a neutral or beneficial trans-isomer. Increasing the content of n-3 PUFA in beef can influence colour shelf life and sensory attributes of the meat. As the content of n-3 PUFA increases then sensory attributes such as "greasy" and "fishy" score higher and colour shelf life may be reduced. Under these situations, high levels of vitamin E are necessary to help stabilise the effects of incorporating high levels of long chain PUFA into meat. However, grass feeding not only increases n-3 PUFA and CLA but, due to its high content of vitamin E, colour shelf life is improved. It is evident that opportunities exist to enhance the content of health promoting fatty acids in beef and beef products offering opportunities to add value and contribute to market differentiation. However, it is imperative that these approaches to deliver "functional" attributes do not compromise on the health value (lipoperoxidation) or the taste of beef products.     

A model for the hot water decontamination of sides of beef in a novel cabinet based on laboratory data

A predictive model for the hot water decontamination of sides of beef in a novel design of cabinet is presented and its usefulness illustrated. The model is based on laboratory data and permits assessment of bacterial reductions, production rates, unit energy costs and changes to cabinet dimensions and ambient temperatures. The advantages of a 'standard' cabinet recommended for a wide range of abattoir production rates are outlined. For a production rate of 135 sides h⁻¹, 90% and 99% reductions in bacteria at the site of minimum treatment (the neck) could be achieved at costs of less than 0.016% and 0.03% respectively of the value of the meat. The model assumes limited exposure of the sides to the hot water to prevent a permanent impairment of meat bloom. A graphical summary is presented and limitations of the model are discussed.     

Intensive sheep and beef production from pasture — A New Zealand perspective of concerns,opportunities and challenges

This paper details current production trends for sheep and beef cattle production in New Zealand and gives some insight into the opportunities for improvement based on New Zealand research at Massey University. Further it outlines some of the challenges the industries face in the near future. The New Zealand climate favours pasture growth and this is the key to sheep and beef cattle production with over 95% of the diet being grazed pasture or crop. Exports are the focus of the industry with 95% of sheep meat and wool, and 80% of beef exported. There have been considerable gains in production over the last 20 years but there still remains a huge opportunity for further intensification through breeding sheep at an earlier age, increasing the weight of lambs weaned per ewe per year and improving beef production systems. These improvements need to occur within a framework of minimal environmental footprint and produce products that are in demand in the high end international markets.     

Effect of South African beef production systems on post-mortem muscle energy status and meat quality

Post-slaughter muscle energy metabolism meat colour of South African production systems were compared; steers (n = 182) of Nguni, Simmental Brahman crossbreds were reared on pasture until A-, AB-, or B-age, in feedlot until A–AB-age. After exsanguination carcasses were electrically stimulated (400 V for 15 s). M. longissimus dorsi muscle energy samples were taken at 1, 2, 4 and 20 h. Post-mortem samples for meat quality studies were taken at 1, 7 and 14 days post-mortem. Production systems affected muscle glycogen, glucose, glucose-6-P, lactic acid, ATP, creatine-P glycolytic potential (P < 0.05), with the muscles of feedlot carcasses having a faster glycolysis rate than pasture carcasses. Energy metabolites correlated (0.4 < r < 0.9) with meat colour (CIE, L*a*b*), (0.3 < r > 0.5) water holding capacity, drip loss, and Warner Bratzler shear force. Muscle energy only affected muscle contraction of the A-age-pasture system (shortest sarcomere length of 1.66 μm vs 1.75 μm highest WBS of 6 kg vs 5 kg 7 days post-mortem).     

Central nervous system tissue detection in meat from advanced meat recovery systems

Three hundred meat samples, recovered from beef neck- and breast-bones using a conventional advanced meat recovery (AMR) system, the de-sinewed minced meat (DMM10) technology, and hand-boning, were collected and tested for presence of central nervous system tissue (CNST) in meat using an ELISA-based test. Samples were collected at two processing facilities (Est. A and B). Sternum meat was the non-CNST reference (control) – it is distant from brain and spinal cord locations on a carcass, with low likelihood of contamination with CNST. Neckbone meat was recovered from bones obtained from carcasses where the spinal cord was removed manually, Est. B, or using a Jarvis circular hydraulic cord remover saw, Est. A. All samples from AMR, DMM, and hand methods showed lower calculated levels of “risk material” than the stated limit of detection (0.1%) of ELISA kit. There was no apparent difference among these, and use of the Jarvis saw had no perceptible advantage.     

Effect of feeding treatment during the backgrounding phase of beef production from pasture on: I. Animal performance, carcass and meat quality

This research evaluated effects of feedlot backgrounding on 40, 70 or 100% alfalfa hay diets (40hay, 70hay; 100hay, respectively) or pasture grazing (Pasture) before pasture finishing, on performance and beef characteristics of Angus heifers. Ninety six female calves were allocated to the four feeding strategies. Backgrounding took place during 114 days and subsequent pasture finishing over 132 days. Heifers of each strategy were slaughtered after 114 days (end of the feedlot period) and at end of the study when all remaining animals were finished on pasture. Effects of backgrounding were associated with rate of gain. Backgrounding strategies 40hay and Pasture resulted in the best performance. Beef attributes were similar. At the end of the feedlot period, 100hay was smaller and leaner, less tender and less juicy. At the end of the study, Pasture and 40hay heifers had on average the largest back fat thickness and intramuscular fat measurements. No treatment effects were detected for Warner-Bratzler shear force, muscle pH, muscle color and sensory panel attributes.     

An exploratory observational study to develop an improved method for quantifying beef carcass salable meat yield

Eighty-seven grain-finished steers were harvested, evaluated, and fabricated into wholesale cuts to determine what measured composition indicators most accurately describe the percentage of closely trimmed salable meat yield. Indicators of lean and fat composition present at the cross-section between the 12th and 13th ribs were objectively evaluated using Assess image analysis software. Salable meat yield ranged from 50.18% to 72.92%, trimmable fat yield ranged from 12.87% to 36.69%, and bone yield ranged from 10.07% to 19.21%. Regression models were developed to estimate percentage of total salable meat yield. Composition indicators chosen to predict salable meat yield included hot carcass weight (HCW), perinephric fat weight, longissimus muscle area (LMA), subcutaneous fat thickness (SFT), ratio of LMA to subcutaneous fat area, and ratio of subcutaneous fat depth to HCW. These results indicate that prediction of beef carcass salable meat yield can be improved via modification to current measures used in the USDA yield grade equation and addition of new measures.     

烤肉制品生产问题分析与探讨

阐述了烤猪精肉的生产配方及工艺；分析与探讨了烤肉制品生产中出现的问题。