Transesterification of palm oil on KyMg1 − xZn1 + xO3 catalyst: Effect of Mg-Zn interaction

The Mg-Zn interaction effect of K_yMg_1 − xZn_1 + xO₃ heterogeneous type catalyst and its performance on transesterification of palm oil have been studied using the response surface methodology and the factorial design of experiments. The catalyst was synthesized using the co-precipitation method and the activity was assessed by transesterification of palm oil into fatty acid methyl esters. The ratio of the Mg/Zn metal interaction, temperature and time of calcination were found to have positive influence on the conversion of palm oil to fatty acid methyl ester (FAME) with the effect of metal to metal ratio and temperature of calcination being more significant. The catalytic activity was found to decrease at higher calcination temperature and the catalyst type K₂Mg_0.34Zn_1.66O₃ with Mg/Zn ratio of 4.81 gave FAME content of 73% at a catalyst loading of 1.404 wt.% of oil with molar ratio of methanol to oil being 6:1 at temperature of 150 °C in 6 h. A regression model was obtained to predict conversions to methyl esters as a function of metal interaction ratio, temperature of calcination and time. The observed activity of the synthesized catalyst was due to its synergetic structure and composition.     

New binary (1 − x)Ba(Lu1/2Nb1/2)O3-xPbTiO3 solid solution with morphotropic phase boundary

A new ferroelectric solid solution of (1 − x)Ba(Lu_1/2Nb_1/2)O₃-xPbTiO₃ (BLN-PT) (0 ≤ x ≤ 1) has been synthesized by solid state reactions. Its structure and electric properties have been studied by X-ray diffraction and di-/ferro-electric measurements. Based on the investigation, a partial solid state phase diagram of the binary BLN-PT ceramics system has been established, which exhibits a morphotropic phase boundary (MPB) region in the composition range of 0.64 ≤ x ≤ 0.68. The Curie temperature is measured to be around 250 °C in the vicinity of the MPB region, which is much higher than that of PMNT or PZNT system. The dielectric behavior has been discussed based on Curie-Weiss Law and Lorentz-type quadratic relationship. With increasing PT content, a transformation from relaxor to ferroelectric phase has been demonstrated in the solid solution system.     

Effect of Pt addition on the isomerization properties of MoO2 − x(OH)y deposited on TiO2

Isomerization of n-hexane and n-pentane were studied using equivalent 5 monolayers of MoO₃ deposited on TiO₂. Addition of 2.5% Pt by weight of MoO₃ on the Mo catalyst resulted in an increase in the catalytic activity of the system in favor of hydrocracking products. Surface characterization by XPS-UPS and ISS reveal that the sample surface contains Oxygen, Molybdenum, Platinum and Titanium. Apparently, the metallic properties of the deposited Pt favors the hydrocracking reactions and becomes dominant at reaction temperatures higher than 623 K. Balanced metal-acid functions in MoO_2 − x(OH)_y phase seems to be in optimized condition toward the hydroisomerization process. The contribution of Platinum addition to this catalytic reaction is not obvious. Combination of surface XPS-UPS, ISS and catalytic reactions carried out at similar experimental conditions enabled us to have better insight concerning the catalytic activities of the different chemical species present on the sample surface.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Influence of low concentration of SO2 for selective reduction of NO by C3H8 in lean-exhaust conditions on the activity of Ag/Al2O3 catalyst

The effect of SO₂ for the selective reduction of NO by C₃H₈ on Ag/Al₂O₃ was investigated in the presence of excess oxygen and water vapor. The NO_x conversion decreased permanently even in the presence of a low concentration of SO₂ (0.5–10 ppm) at <773 K. The increase in SO₂ concentration resulted in a large decrease in NO_x conversion at 773 K. However, when the reaction temperature was more than 823 K, the activity of Ag/Al₂O₃ remained constant even in the presence of 10 ppm of SO₂. The sulfate species formed on the used Ag/Al₂O₃ were characterized by a temperature programmed desorption method. The sulfated species formed on silver should mainly decrease the deNO_x activity on the Ag/Al₂O₃. The sulfated Ag/Al₂O₃ was appreciably regenerated by thermal treatment in the deNO_x feed at 873 K. The moderate activity remains at 773 K in the presence of 1 ppm SO₂ for long time by the heat treatment at every 20 h intervals.     

NOx storage behavior and sulfur-resisting performance of the third-generation NSR catalysts Pt/K/TiO2–ZrO2

The NO_x storage and reduction (NSR) catalysts Pt/K/TiO₂–ZrO₂ were prepared by an impregnation method. The techniques of XRD, NH₃-TPD, CO₂-TPD, H₂-TPR and in situDRIFTS were employed to investigate their NO_x storage behavior and sulfur-resisting performance. It is revealed that the storage capacity and sulfur-resisting ability of these catalysts depend strongly on the calcination temperature of the support. The catalyst with theist support calcined at 500 °C, exhibits the largest specific surface area but the lowest storage capacity. With increasing calcination temperature, the NO_x storage capacity of the catalyst improves greatly, but the sulfur-resisting ability of the catalyst decreases. In situ DRIFTS results show that free nitrate species and bulk sulfates are the main storage and sulfation species, respectively, for all the catalysts studied. The CO₂-TPD results indicate that the decomposition performance of K₂CO₃ is largely determined by the surface property of the TiO₂–ZrO₂ support. The interaction between the surface hydroxyl of the support and K₂CO₃ promotes the decomposition of K₂CO₃ to form –OK groups bound to the support, leading to low NO_x storage capacity but high sulfur-resisting ability, while the interaction between the highly dispersed K₂CO₃ species and Lewis acid sites gives rise to high NO_x storage capacity but decreased sulfur-resisting ability. The optimal calcination temperature of TiO₂–ZrO₂ support is 650 °C.     

Oxidation behavior and kinetics of in situ (TiB2 + TiC)/Ti3SiC2 composites in air

The isothermal oxidation behavior of in situ (TiB₂ + TiC)/Ti₃SiC₂ composite ceramics with different TiB₂ content has been investigated at 900-1200 °C in air for exposure times up to 20 h by means of X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and energy dispersive spectroscopy. The oxidation of (TiB₂ + TiC)/Ti₃SiC₂ composites follows a parabolic rate law. With the increase in TiB₂ content, the oxidation weight gain, thickness of the oxidation scale, and parabolic rate constant decrease dramatically, which suggests that the incorporation of TiB₂ greatly improves the oxidation resistance of the composites. With the increase in oxidation temperature, the enhancement effect becomes more pronounced. Due to the incorporation of TiB₂, the oxidation scale of (TiB₂ + TiC)/Ti₃SiC₂ composites is generally composed of an outer layer of coarse-grained TiO₂ and an inner layer of amorphous boron silicate and fine-grained TiO₂. Only the dense inner layer formed on the surface acts as a diffusion barrier, retarding the inward diffusion of O, and consequently contributing to the improved oxidation resistance of the (TiB₂ + TiC)/Ti₃SiC₂ composites.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Effects of B-site ion (M) substitution on the ionic conductivity of (Li3xLa2/3−x)1+y/2(MyTi1−y)O3 (M=Al, Cr)

Effect on the ionic conductivity of B-site ion (M) substitution in (Li_3xLa_2/3−x)_1+y/2M_yTi_1−yO₃ (M=Al, Cr) has been investigated. It has been found that partial substitution of smaller Al³⁺ for Ti⁴⁺ is effective to enhance the ionic conductivity of Li_3xLa_2/3−xTiO₃. At 300 K, the maximum bulk conductivity of (1.58±0.01)×10⁻³ S cm⁻¹ is observed from the composition of (Li_0.39La_0.54)_1−y/2Al_yTi_1−yO₃ with y=0.02 (x=0.13), that is the highest yet reported for known perovskite solutions at room temperature. The conductivity enhancement is interpreted as being due to the substitution-induced bond-strength change rather than due to bottleneck size change for Li migration, TiO₆-octahedron tilting or A-site cation ordering.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Ethanol steam reforming reactions over Al2O3 · SiO2-supported Ni-La catalysts

Nickel-based catalysts supported on Al₂O₃ · SiO₂ were prepared with modification of the second metal involving La, Co, Cu, Zr or Y, of which the catalytic behaviors were assessed in the ethanol steam reforming reaction. Activity test indicated that addition of La resulted in higher selectivity of hydrogen and lower selectivity of carbon monoxide, compared with Co-doped nickel catalyst. Influences of lanthanum amounts on catalytic performance were studied over 30NixLa/Al₂O₃ · SiO₂ (x = 5, 10, 15), and characterizations by XRD, TPR and XPS indicated that low amount of lanthanum additives (5%) was superior to inhibit the crystal growth of nickel as well as beneficial to the reduction of nickel oxide. Finally 100 h test for the optimal catalyst 30Ni5La/Al₂O₃ · SiO₂ indicated its good long-term stability to provide high hydrogen selectivity and low carbon monoxide formation, as well as good resistance to coke deposition at low temperature.     

Theoretical approach to cell-impedance-controlled lithium transport through Li1 − δMn2O4 film electrode with partially inactive fractal surface by analyses of potentiostatic current transient and linear sweep voltammogram

Lithium transport through the partially inactive fractal Li_1 − δMn₂O₄ film electrode under the cell-impedance-controlled constraint was theoretically investigated by using the kinetic Monte Carlo method based upon random walk approach. Under the cell-impedance-controlled constraint, all the potentiostatic current transients calculated from the totally active and partially inactive fractal electrodes hardly exhibited the generalised Cottrell behaviour and they were significantly affected in shape by the interfacial charge-transfer kinetics. In the case of the linear sweep voltammogram determined from the totally active and partially inactive fractal electrodes, all the power dependence of the peak current on the scan rate above the characteristic scan rate deviated from the generalised Randles-Sev?ik behaviour. From the analyses of the current transients and the linear sweep voltammograms simulated with various values of the simulation parameters, it was further recognised that the cell-impedance-controlled lithium transport through the partially inactive fractal Li_1 − δMn₂O₄ film electrode strongly deviates from the generalised diffusion-controlled transport behaviour of the electrode with the totally active surface, which is attributed to the impeded interfacial charge-transfer kinetics governed by the surface inhomogeneities including the fractal dimension of the surface and the surface coverage by active sites and by the kinetic parameters including the internal cell resistance.     

Synthesis and characterization of A2 + B3-type hyperbranched aromatic polyesters with phenolic end groups

Hyperbranched (hb) aromatic polyesters with phenolic end groups were synthesized according to the A₂ + B₃ approach both, by solution polymerization and by melt (bulk) polymerization with different monomer ratios (A₂:B₃). The hb polyesters produced from solution polymerization exhibited higher yields, molar masses and glass transition temperature (T_g) compared to the products prepared in the melt. The resulting hb aromatic polyesters from the A₂ + B₃ approach were also compared with their properties to hb aromatic polymers produced from the well known AB₂ monomer 3,5-bis(trimethylsiloxy)benzoyl chloride. Both types of hb aromatic polyesters possess high T_g, high thermal stability and good solubility in common organic solvents. A typical melt viscosity behavior with shear thinning effect was also observed for both. Thus similar polymer properties compared to melt-condensed products were obtained with the A₂ + B₃ approach by solution polycondensation possessing the advantage of easy monomer availability and much milder polymerization conditions (at room temperature in solution) compared to the AB₂ approach.     

Simultaneous reduction of NOx and SO2 emissions from coal combustion by calcium magnesium acetate

The potential of calcium magnesium acetate (CMA) as a medium for the simultaneous control of NO_x and SO_x emissions has been investigated using a pulverized coal combustion rig operating at 80 kW. A US and a UK coal of significantly different sulphur contents were used as primary fuel and CMA was injected in solution form into the combustion gases by horizontally opposed twin-fluid atomisers at temperatures of 1100-1200 °C. SO₂ reductions typically greater than 80 and 70% were found for initial SO₂ levels of 1000 and 1500 ppm, respectively, at Ca/S ratios greater than 2.5. There did not appear to be significant limitation on sulphation by pore blockage using CMA due to the open structure formed during calcination and there is clear potential for zero SO₂ emissions at higher Ca/S ratios. The Ca content of the CMA in the form of CaO, via a droplet drying/particle calcination process, absorbs SO₂ by sulphation processes by penetration into the open pore structure of these particles. The effect of primary zone stoichiometry (λ₁=1.05, 1.15 and 1.4) on NO_x reduction was investigated for a range of CMA feed rates up to a coal equivalent of 24% of the total thermal input. NO_x reductions of 80, 50 and 30% were achieved at a primary zone stoichiometry of λ₁=1.05, 1.15 and 1.4, respectively, for a reburn zone residence time of 0.8 s. At lower equivalent reburn fuel fractions, coal gave greater NO_x reductions than CMA but similar levels were achieved above Rff=18%. The mechanism for NO_x reduction involves the organic fraction of CMA which pyrolyses into hydrocarbon fragments (CH_i), but to a lesser degree than coal, which may then react with NO_x in a manner similar to a conventional ‘reburn’ mechanism where NO_x is partly converted to N₂ depending on the availability of oxygen.     

Ultrasonic spray pyrolysis of nano crystalline spinel LiMn2O4 showing good cycling performance in the 3 V range

Spherical lithium manganese oxide spinel was synthesized by an ultrasonic spray pyrolysis method, and has been characterized using X-ray diffraction, scanning electron microscopy, transimission electron microscopy and electrochemical cycling at 3 V regions. The LiMn₂O₄ powders were composed of about 10 nm-sized primary particles. The delivered discharge capacity of the synthesized nano-material was 125 mAh g⁻¹ between 2.4 and 3.5 V and its retention was about 96% upon 50 cycling. From the high resolution transmission electron microscopic study, it was found that structural transition of the parent material did not occur even after the 50th electrochemical cycling on the 3 V region. It seems that the reversible structural change is possible for nanocrystalline LiMn₂O₄ as observed by the X-ray diffraction and transition electron microscopic observations.