Thermal stability and aging characteristics of (natural rubber)/(waste ethylene‐propylene‐diene monomer terpolymer) blends

Comparative studies of the thermogravimetric analysis and thermo‐oxidative aging of (natural rubber)/(waste ethylene‐propylene‐diene monomer terpolymer) (NR/W‐EPDM) and (natural rubber)/(ethylene‐propylene‐diene monomer terpolymer) (NR/EPDM) blends were carried out. The blends were prepared at five different blend ratios (90/10, 80/20, 70/30, 60/40, and 50/50) on a two‐roll mill. As the pure EPDM or W‐EPDM content in the blends increased, their thermal stability also increased. The thermo‐oxidative aging of these blends was done at 100°C for 48 h. Afterwards, the NR/EPDM blends exhibited better retention of properties than the NR/W‐EPDM blends. Crosslink density measurements of the blends after thermal aging indicated that higher crosslink density was obtained from a higher content of EPDM or W‐EPDM, a result which might be due to the high rate of radical termination leading to crosslinks in the bulk of the polymer. J. VINYL ADDIT. TECHNOL., 20:99–107, 2014. © 2014 Society of Plastics Engineers     

Effect of blend ratio on cure characteristics,tensile properties,thermal and swelling properties of mica‐filled (ethylene‐propylene‐diene monomer)/(recycled ethylene‐propylene‐diene monomer) (EPDM/r‐EPDM) blends

(Ethylene‐propylene‐diene monomer)/(recycled ethylene‐propylene‐diene monomer) (EPDM/r‐EPDM) blends filled with constant mica loading were compounded at various blends ratios (i.e., 90/10, 80/20, 70/30, 60/40, and 50/50). Results indicated that scorch time decreased with increasing r‐EPDM content, whereas curing time, minimum torque, and maximum torque show the opposite trend. The tensile strength, stress at 100% elongation, and elongation at break value increased with increasing r‐EPDM loading in the blend systems and the optimum properties occurred at 70/30 EPDM/r‐EPDM blends ratio. The thermal stability of EPDM/r‐EPDM blends increased with increasing r‐EPDM content in the blends but the swelling percentage showed the opposite trend with a greater addition of r‐EPDM content in the blends. J. VINYL ADDIT. TECHNOL., 21:1–6, 2015. © 2014 Society of Plastics Engineers     

Cure characteristics,morphology, and mechanical properties of ethylene–propylene–diene–monomer rubber/acrylonitrile butadiene rubber blends

Blends based on ethylene–propylene–diene monomer rubber (EPDM) and acrylonitrile butadiene rubber (NBR) was prepared. Sulfur was used as the vulcanizing agent. The effects of blend ratio on the cure characteristics and mechanical properties, such as stress–strain behavior, tensile strength, elongation at break, hardness, rebound resilience, and abrasion resistance have been investigated. Tensile and tear strength showed synergism for the blend containing 30% of NBR, which has been explained in terms of morphology of the blends attested by scanning electron micrographs. A relatively cocontinuous morphology was observed for 70 : 30, EPDM/NBR blend system. The experimental results have been compared with the relevant theoretical models. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Melt rheology and properties of compatibilized recycled poly(ethylene terephthalate)/(styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer blends

Blends of recycled poly(ethylene terephthalate) (R‐PET) and (styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer (SEEPS) compatibilized with (maleic anhydride)‐grafted‐styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MAH) were prepared by melt blending. The compatibilizing effects of SEBS‐g‐MAH were investigated systematically by study of the morphology, linear viscoelastic behavior, and thermal and mechanical properties of the blends. The results show that there is good agreement between the results obtained by rheological measurement and morphological analysis. The rheological test shows that the melt elasticity and melt strength of the blends increase with the addition of SEBS‐g‐MAH. The Cole‐Cole plots and van Gurp‐Palmen plots confirm the compatibilizing effect of SEBS‐g‐MAH. However, the Palierne model fails to predict the linear viscoelastic properties of the blends. The morphology observation shows that all blends exhibit a droplet‐matrix morphology. In addition, the SEEPS particle size in the (R‐PET)/SEEPS blends is significantly decreased and dispersed uniformly by the addition of SEBS‐g‐MAH. Differential scanning calorimeter analysis shows that the crystallization behavior of R‐PET is restricted by the incorporation of SEEPS, whereas the addition of SEBS‐g‐MAH improves the crystallization behavior of R‐PET compared with that of uncompatibilized (R‐PET)/SEEPS blends. The Charpy impact strength of the blends shows the highest value at SEBS‐g‐MAH content of 10%, which is about 210% higher than that of pure R‐PET. J. VINYL ADDIT. TECHNOL., 22:342–349, 2016. © 2014 Society of Plastics Engineers     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Effect of dynamic crosslinking on tensile yield behavior of polypropylene/ethylene‐propylene‐diene rubber blends

Tensile yield behavior of the blends of polypropylene (PP) with ethylene‐propylene‐diene rubber (EPDM) is studied in blend composition range 0–40 wt % EPDM rubber. These blends were prepared in a laboratory internal mixer by simultaneous blending and dynamic vulcanization. Vulcanization was performed with dimethylol phenolic resin. For comparison, unvulcanized PP/EPDM blends were also prepared. In comparison to the unvulcanized blends, dynamically vulcanized blends showed higher yield stress and modulus. The increase of interfacial adhesion caused by production of three‐dimensional network is considered to be the most important factor in the improvement. It permits the interaction of the stress concentrate zone developed at the rubber particles and causes shear yielding of the PP matrix. Systematic changes with varying blend composition were found in stress‐strain behavior in the yield region, viz., in yield stress, yield strain, width of yield peak, and work of yield. Analysis of yield stress data on the basis of the various expressions of first power and two‐thirds power laws of blend compositions dependence and the porosity model led to consistent results from all expression about the variation of stress concentration effect in both unvulcanized and vulcanized blend systems. Shapes and sizes of dispersed rubber phase (EPDM) domains at various blend compositions were studied by scanning electron microscopy. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2104–2121, 2000     

Effect of silane coupling agent on the curing,tensile, thermal,and swelling properties of ethylene‐propylene‐diene monomer rubber (EPDM)/mica composites

The influence of silane (bis[3‐triethoxysilylpropyl] tetrasulfide) coupling agent on the properties of ethylene‐propylene‐diene monomer rubber (EPDM)/mica composites was studied. Both EPDM/mica composites with silane and those without silane were compounded by using a two‐roll mill at various filler loadings (i.e., 100/0, 100/10, 100/30, 100/50, 100/70). The tensile and thermal properties as well as the fracture surfaces of the composites were investigated by using an Instron Universal Testing Machine, a thermal gravimetric analyzer, and a field emission scanning electron microscope. The results indicated that the optimum cure time (t₉₀) and scorch time (t_s2) values were shorter, whereas the maximum torque (M_H) value was slightly higher, for EPDM/mica composites with silane compared to those without silane. The tensile properties, modulus at 100% elongation, and modulus at 300% elongation increased for the composites made with silane, and the optimum filler loading for those properties was 50 parts by weight per hundred parts of rubber. In addition, thermal stability and swelling ratio for both composites improved with increased filler loading. However, the composites with silane showed better thermal stability and swelling ratio because of stronger linkage at the rubber‐filler boundary, which promoted filler dispersion. J. VINYL ADDIT. TECHNOL., 20:116–121, 2014. © 2014 Society of Plastics Engineers     

Dynamic mechanical analysis of ethylene–propylene–diene monomer rubber and styrene–butadiene rubber blends

The effects of blend ratio, crosslinking systems, and fillers on the viscoelastic response of ethylene–propylene–diene monomer (EPDM)/styrene–butadiene rubber (SBR) blends were studied as functions of frequency, temperature, and cure systems. The storage modulus decreased with increasing SBR content. The loss modulus and loss tangent results showed that the EPDM/SBR blend vulcanizate containing 80 wt % EPDM had the highest compatibility. Among the different cure systems studied, the dicumyl peroxide cured blends exhibited the highest storage modulus. The reinforcing fillers were found to reduce the loss tangent peak height. The blend containing 40 wt % EPDM showed partial miscibility. The dispersed EPDM phase suppressed the glass‐transition temperature of the matrix phase. The dynamic mechanical response of rubbery region was dominated by SBR in the EPDM–SBR blend. The morphology of the blend was studied by means of scanning electron microscopy. The blend containing 80 wt % EPDM had small domains of SBR particles dispersed uniformly throughout the EPDM matrix, which helped to toughen the matrix and prevent crack propagation; this led to enhanced blend compatibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of dynamic crosslinking on impact strength and other mechanical properties of polypropylene/ethylene‐propylene‐diene rubber blends

The deformation and fracture behavior of several dynamic vulcanizate blends of isotactic polypropylene with ethylene‐propylene‐diene rubber (EPDM) was examined and compared with those of uncrosslinked blends of PP/EPDM. These blends were prepared by melt mixing in an internal mixer at 190°C in a composition range of 10–40 wt % EPDM rubber. The variation in yield stress, the strength of fibrils of the craze, and the number density of the EPDM rubber domains (morphology fixation) that are dominant factors for enhancing interfacial adhesion and toughness in dynamic vulcanizate blends were evaluated. The ductility and toughness of these materials were explained in light of the composition between crack formation and the degree of plastic deformation through crazing and shear yielding. The physicomechanical properties including the hardness, yield stress, Young's modulus, percentage elongation, impact strength, flexural strength, and flexural modulus of dynamic vulcanized blends were found to be consistent and displayed higher values compared with uncrosslinked blends. The nucleation effect of the crosslinked particles and the decrease of crystallinity of the EPDM rubber were also considered to contribute to the improvement in the impact strength. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2089–2103, 2000     

Adhesion properties of (epoxidized natural rubber)/(ethylene‐propylene‐diene rubber) blend adhesive: Effect of blend ratio and testing rate

The adhesion properties of epoxidized natural rubber (ENR 25)/(ethylene‐propylene‐diene rubber) blend adhesive were investigated by using various blend ratios of the two rubbers and rate of testing. Coumarone‐indene resin was used as the tackifier. Results show that the loop tack and peel strength of adhesives increase steadily up to 60% ENR 25 before decreasing with further increase in % ENR 25. This observation is attributed to an increase in wettability and compatibility up to the optimum value of the ENR 25 blend ratio. However, shear strength increases continuously with increasing percentage of ENR 25, an observation that is ascribed to the increasing cohesive strength of the blend adhesive. In all cases, the adhesion properties increase with increasing coating thickness and testing rates. J. VINYL ADDIT. TECHNOL., 22:134–139, 2016. © 2014 Society of Plastics Engineers     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Ethylene vinyl acetate as compatibilizer on cure characteristics and mechanical properties of (natural rubber)/(Recycled acrylonitrile‐butadiene rubber) blends

Ethylene vinyl acetate (EVA) has been used as a compatibilizer for (natural rubber)/(recycled acrylonitrile‐butadiene rubber) (NR/NBRr) blends, vulcanized by sulfur. EVA offers excellent heat, ozone, and weather resistance, whereas the vinyl acetate groups provide oil resistance to the blend. It exhibits good tear resistance and may be crosslinked. However, EVA exhibits poor low‐temperature flexibility. NBR gloves have excellent resistance to punctures, tears, and many types of chemicals, while NR has good physical and mechanical properties. NR/NBRr blends were prepared with various compositions with the EVA content fixed. Tensile properties, hardness, and swelling behavior tests were performed to determine the compatibility of NR/NBRr blends in the presence of EVA. Results indicated that incorporation of EVA into NR/NBRr blends improved tensile strength, modulus, and elongation at break compared with NR/NBRr blends without EVA. The improvement in hardness and reduction in resilience on compatibilization are due to an increase in crosslink density, which gives NR/NBRr blends better swelling resistance. Scanning electron microscopy of the fracture surfaces indicates that, with the addition of EVA in NR/NBRr blends, better adhesion between NR and NBRr was obtained, thus improving the compatibility of NR/NBRr blends. J. VINYL ADDIT. TECHNOL., 23:135–141, 2017. © 2015 Society of Plastics Engineers     

Thermoplastic elastomers based on recycled high‐density polyethylene,ethylene–propylene–diene monomer rubber,and ground tire rubber

High‐performance thermoplastic elastomers (TPEs), based on recycled high‐density polyethylene (HDPE^R), olefinic type ethylene–propylene–diene monomer rubber (EPDM), and ground tire rubber (GTR) treated with bitumen, were prepared by using dynamic vulcanization technology, and their structure–property relationships were investigated. It was established that special pretreatment of GTR by bitumen confers outstanding mechanical properties on the resulting TPEs. TPEs, containing GTR pretreated by bitumen, exhibit thermal behavior similar to that of the HDPE^R/EPDM basic blend in the temperature region up to about 340°C. Rheological measurements showed that bitumen acts as an effective plasticizer for the GTR‐containing TPEs. SEM, DSC, and DMTA results revealed improved adhesion between the particles of GTR treated by bitumen and the surrounding thermoplastic matrix, compared to that of the untreated GTR particles. It was concluded that bitumen acts as an effective devulcanizing agent in the GTR treatment stage. In the following steps of TPE production, bitumen acts simultaneously as a curing agent for the rubber components (EPDM/GTR) and as a compatibilizer for the blend components. GTR‐containing TPEs, prepared by extrusion technology, were reprocessed (by passing through the extruder six times) without any observable changes in their tensile properties, thermal stability, and melt viscosity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 659–671, 2005     

Improvement in thermal conductivity and mechanical properties of ethylene‐propylene–diene monomer rubber by expanded graphite

Thermally conductive fillers are usually employed in the preparation of rubber composites to enhance thermal conductivity. In this work, ethylene‐propylene‐diene monomer rubber (EPDM)/expanded graphite (EG) and EPDM/graphite composites with up to 100 phr filler loading were prepared. Compared to EPDM/graphite compounds with the same filler loading, stronger filler network was demonstrated for EPDM/EG compounds. Thermal conductivity and mechanical properties of EPDM/graphite and EPDM/EG composites were compared and systematically investigated as a function of the filler loading. The thermal conductivity of both EPDM/graphite and EPDM/EG composites increased with increasing volume fraction of fillers, and could be well fitted by Geometric Mean Model. The thermal conductivity as high as 0.910 W · m⁻¹ · K⁻¹ was achieved for the EPDM/EG composite with 25.8 vol% EG, which was ∼4.5 times that of unfilled EPDM. Compared to EPDM/graphite composites, EPDM/EG composites exhibited much more significant improvement in thermal conductivity and mechanical properties, which could be well correlated with the better filler‐matrix interfacial compatibility and denser structure in EPDM/EG composites, as revealed in the SEM images of tensile fracture surfaces. POLYM. COMPOS., 38:870–876, 2017. © 2015 Society of Plastics Engineers     

Effect of dynamic cross‐linking on melt rheological properties of polypropylene/ethylene‐propylene‐diene rubber blends

Study of melts rheological properties of unvulcanized and dynamically vulcanized polypropylene (PP)/ethylene‐propylene‐diene rubber (EPDM) blends, at blending ratios 10–40 wt %, EPDM, are reported. Blends were prepared by melt mixing in an internal mixer at 190°C and rheological parameters have been evaluated at 220°C by single screw capillary rheometer. Vulcanization was performed with dimethylol phenolic resin. The effects of (i) blend composition; (ii) shear rate or shear stress on melt viscosity; (iii) shear sensitivity and flow characteristics at processing shear; (iv) melt elasticity of the extrudate; and (v) dynamic cross‐linking effect on the processing characteristics of the blends were studied. The melt viscosity increases with increasing EPDM concentration and decreased with increasing intensity of the shear mixing for all compositions. In comparison to the unvulcanized blends, dynamically vulcanized blends display highly pseudoplastic behavior provides unique processing characteristics that enable to perform well in both injection molding and extusion. The high viscosity at low shear rate provides the integrity of the extrudate during extrusion, and the low viscosity at high shear rate enables low injection pressure and less injection time. The low die‐swell characteristics of vulcanizate blends also give high precision for dimensional control during extrusion. The property differences for vulcanizate blends have also been explained in the light of differences in the morphology developed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1488–1505, 2000     

Dielectric behavior of aluminum hydroxide‐filled oil‐extended ethylene‐propylene‐diene‐monomer rubber composites in microwave fields

Oil‐extended ethylene‐propylene‐diene rubber composites were prepared with aluminum hydroxide (ATH) and high abrasion furnace carbon black. The dielectric properties at microwave frequencies of the samples were measured in the S (2–4 GHz) band using cavity perturbation technique. The thermal stability of the composites was studied using thermogravimetric analysis. The morphology of the composites was investigated by scanning electron microscopic studies. The fire retardancy of the composites was identified through the limiting oxygen index and horizontal burning test (UL94 HB). The dielectric permittivity, AC conductivity, and absorption coefficient of the highly ATH loaded systems are much greater than the unfilled and lower systems. At higher loading, the dielectric heating coefficient and skin depth were found to decrease significantly. The incorporation of ATH was found to improve the thermal stability and flame retardancy of EPDM. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Compatibilization of nitrile‐butadiene rubber/ethylene‐propylene‐diene monomer blends by mercapto‐modified ethylene‐vinyl acetate copolymers

Mercapto‐modified ethylene‐vinyl acetate (EVASH) has been employed as a reactive compatibilizing agent for nitrile‐butadiene rubber (NBR)/ethylene‐propylene‐diene monomer (EPDM) blends vulcanized with a sulfur/2,2′‐dithiobisbenzothiazole (MBTS) single accelerator system and a (sulfur/MBTS/tetramethylthiuram disulfide (TMTD) binary accelerator system. The addition of 5.0 phr EVASH resulted in a significant improvement in the tensile properties of blends vulcanized with the sulfur/MBTS system. In addition to better mechanical performance, these functionalized copolymers gave rise to a more homogeneous morphology and, in some cases, better aging resistance. The compatibilization was not efficient in blends vulcanized with the S/MBTS/TMTD binary system, probably because of the faster vulcanization process occurring in this system. The good performance of these EVASH samples as compatibilizing agents for NBR/EPDM blends is attributed to the higher polarity of these components that is associated with their lower viscosity. Dynamic mechanical analysis also suggested a good interaction between the phases in the presence of EVASH. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1404–1412, 2004     

Effects of dynamic vulcanization on the physical,mechanical, and morphological properties of high‐density polyethylene/(natural rubber)/(thermoplastic tapioca starch) blends

Blending of high density polyethylene (HDPE), natural rubber (NR), and thermoplastic tapioca starch (TPS) have been studied. Two series of samples having 5–30 wt% of TPS were prepared: (a) unvulcanized blends (control) and (b) dynamically vulcanized HDPE/NR/TPS blends. The composition of the HDPE/NR was constant and fixed at a blend ratio of 70/30. Morphology studies by SEM showed that the TPS particles were homogeneously dispersed and well‐embedded in vulcanized HDPE/NR matrix. The SEM micrographs showed agreement with the tensile strength and elongation at break values. Tensile strength improved significanly when the HDPE/NR/TPS blends were vulcanized by using sulfur curative system. The enhancement in tensile properties is attributed to the crosslinking reaction within the NR phase. J. VINYL ADDIT. TECHNOL., 18:192–197, 2012. © 2012 Society of Plastics Engineers     

Effect of anhydride‐modified ethylene–propylene–diene rubber and ethylene–vinyl acetate copolymers on the compatibilization of nitrile rubber/ethylene–propylene–diene rubber blends

The effects of maleic anhydride modified ethylene–propylene–diene rubber (EPDMMA) and maleic anhydride modified ethylene–vinyl acetate (EVAMA) on the compatibilization of nitrile rubber (NBR)/ethylene–propylene–diene rubber (70:30 w/w) blends vulcanized with a sulfur system were investigated. The presence of EPDMMA and EVAMA resulted in improvements of the tensile properties, whereas no substantial change was detected in the degree of crosslinking. The blend systems were also analyzed with scanning electron microscopy and dynamic mechanical thermal analysis. The presence of EVAMA resulted in a blend with a more homogeneous morphology. The compatibilizing effect of this functional copolymer was also detected with dynamic mechanical analysis. A shift of the glass‐transition temperature of the NBR phase toward lower values was observed. The presence of EPDMMA and EVAMA also increased the thermal stability, as indicated by an improvement in the retention of the mechanical properties after aging in an air‐circulating oven. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2408–2414, 2003     

Study of polypropylene/ethylene‐propylene‐diene monomer blends reinforced with sisal fibers

Thermoplastics reinforced with natural fibers have attracted much attention from researchers because of their advantages, especially regarding environmental aspects. However, poor impact strength, particularly at low temperatures, limits the application of some thermoplastics, such as polypropylene (PP). To minimize this drawback, impact modifiers have been used, including the terpolymer of ethylene‐propylene‐diene (EPDM). In this work, PP/EPDM/sisal composites of distinct compositions were investigated focusing on the effect of the alkali (NaOH) treatment of the vegetable fiber on the composites properties regarding physical, mechanical, thermal, and morphological behavior. The results indicated that flow rate decreases at higher fiber content due to flow hindering by the presence of the fibers. The addition of the fiber, in general, increased Young's modulus and strength (tensile and flexural), whereas impact strength increased for higher EPDM content. The alkali treatment was considered generally efficient in terms of mechanical properties, even though this was not found in the dynamic mechanical analysis. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers