首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
在NSP窑熟料煅烧机理研究基础上,通过六种窑型各带长度划分及各带停留时间计算等系列参数的计算、分析,提出采用小长径比、大斜度和缩短全窑物料停留时间(T)的优化方案;并提出在保证烧成前提下,压缩过渡带长度(L3)和停留时间(t3)能达到提高该带升温速率,优化窑内烧成热工制度的要求。  相似文献   

2.
熟料的烧成质量取决于烧成带温度及停留时间,烧成带温度高,可大大缩短烧成时间,表现为煅烧能力强。如果燃烧不集中,要达到烧成温度,需要更多的燃料。也就是截面热力强度相同,由于煤粉燃烧速度不同,回转窑煅烧能力也会相差很大,这也是预分解产量计算公式中,同规格的窑用各种公式计算窑的产量不断地低于实际产量的原因。所以,提高预分解窑效率的核心是提高烧成带温度,这就需要有尽量高的二次风温度、较细的煤粉细度、工作良好的燃烧器,再辅以富氧燃烧。  相似文献   

3.
徐景福  马克增 《陶瓷》1998,(1):20-23
通过实例探讨了国产煤气短道窑实现快速烧成的可能性.调试结果表明:对北方坯料而言,在不致引起开裂的前提下,窑头温度越高越适合快速烧成;预热带升温速度不宜太快,一般不超过30℃/min;烧成带前段升温速度适当快些,待温度达到1050℃后再稍慢些,有利于烧成速度的提高.  相似文献   

4.
蒋斌 《水泥技术》1997,(1):22-23
ChainModificationofWetProcessKiln贵州水泥厂烧成车间现有4台Φ3.0mx88.68m湿法回转窑,熟料冷却使用多简冷却机(12筒),规格Φ1.1mx5.0m,设计台产为13t/h。窑内热交换装置采用链条。挂链方式为复合链挂法,即链条带热端使用耐热钢垂挂链条,冷端是花环链热瑞先起挂法,链区长度占全窑总长的32%。近年来,窑的产量达不到设计要求,且热耗偏高,影响因素较多,一是窑的预烧能力不足,从实际生产情况来看,干燥带和预热带偏长,火焰发通,高温带短,易串料,使得窑的热工制度不稳定和窑的快转率较低。二是物料在烧成带停留时间…  相似文献   

5.
刘秉金 《水泥》1992,(9):12-17
随着水泥窑的大型化、高效化以及原材料燃料的多样化,窑衬的工作环境更加苛刻,对火砖的性能提出更高的要求。近来国内外作为大型水泥窑烧成带和过渡带的窑衬,主要使用高温烧成和超高温烧成镁铬砖、尖晶石砖和白云石砖。这三种碱性砖作为水泥窑衬已成为鼎足之势。现仅就尖晶石砖在水泥窑上的使用前景作简要分析。一、烧成带用砖的演变水泥窑烧成带是全窑的高温带,物料温度可达1400~1500℃,而气流温度还要比物料温度高许多。这是全窑的最关键部位,是窑衬使用条件最苛刻的地段。烧成带最初用的是烧粘土砖、Al_2O_3含量在30%~40%之间。随着水泥质  相似文献   

6.
蓝兴权 《水泥》2003,(6):31-32
1现状及存在问题我厂有4台Φ3.5m×145m华新窑,熟料产质量均偏低,无论配料和操作如何努力,出窑熟料产量只能稳定在21~23t/h,难以提高。经现场及数据分析,在设备及工艺状态良好的情况下,窑内物料干燥、预热、分解、烧成各带分布不合理,链区传热面积不足,只有1534.24m2,造成窑内物料干燥预热区向窑头热端前移,烧成带相应缩短,提窑速提产量后,物料在窑内煅烧停留时间不够,经常出现烧不住而跑生的现象,导致了实际生产中,熟料台时产量长期低于24t/h,无法达到25t/h的设计产量,在这种情况下,我厂决定对4号窑链区进行改造,增加链条区域的传热面积。…  相似文献   

7.
徐迅  汪澜  封培然  齐砚勇 《硅酸盐通报》2013,32(10):1949-1952
本文通过数值模拟的手段,建立预分解窑(NSP)物料入窑后在回转窑内的气体、筒壁、物料的温度分布模型,从温度分布规律的角度来看物料温升特点,探讨预分解窑工艺回转窑内熟料烧成进程.模拟认为入窑物料刚进入回转窑时,温度上升缓慢,这将影响到熟料烧成进程,造成回转窑不必要的能量损失.  相似文献   

8.
对于预分解窑来说,回转窑主要承担烧成(结)的任务,熟料煅烧状况的好坏很大程度上取决于高温烧成带温度的高低,即窑前热力强度的强  相似文献   

9.
葛成庭 《水泥》2013,(2):32
我公司5 000t/d生产线采用Φ4.8m×72m回转窑,烧成带采用镁铁铝尖晶石砖。由于经验不足,在生产过程中,为防止耐火材料损坏,烧成带筒体温度时常在150℃左右,熟料的产质量受到很大影响。为确保耐火材料达到使用周期的条件下,提高熟料的产质量,通过计算得出了在保证物料合适填充率及合适停留时间条件下的窑皮厚度,为熟料线的优质高产及耐火材料的安全使用提供了理论指导。  相似文献   

10.
试验研究了一种新的硅酸盐水泥熟料煅烧方法:先用电炉将生料加热到一定温度后再用微波进行强化烧成,实验发现在较低的电加热温度下(1000-1200℃左右),再使用微波强化煅烧1-2min即可烧成熟料,熟料中f-CaO的质量分数在1%-2%之间;人微波炉的物料温度越高,微波加热需要的时间越短,加热到1300℃的物料,微波加热只需40s,熟料中f-CaO的质量分数可降至0.65%,试验证明,采用新的煅烧方法可大幅度提高硅酸盐熟料形成速度;Fe2O3对熟料的微波烧成有很好的促进作用,熟料的XRD图谱显示,熟料矿物的组成和XRD特征衍射与传统方法烧成的熟料一致。  相似文献   

11.
12.
13.
14.
15.
16.
为掌握佛山市顺德新城区降水中污染物的情况,2015年7月至8月,文章作者分别在雨天进行了降水取样,对降水中的pH、电导率、常见阴离子(F-、Cl~-、NO_3~(2-)、SO_4~(2-))及部分重金属(铅和镉)进行监测分析。选择有相关数据的珠江三角洲和石家庄、厦门等地的降水中污染物的情况进行对比。结果表明,顺德新城区降水中的p H和部分阴离子浓度优于珠江三角洲平均值,酸雨类型属于硫酸和硝酸混合型;其水体洁净程度略差于石家庄;铅和镉的浓度也高于厦门,甚至部分超出了人体能直接接触的安全范围。  相似文献   

17.
Saturated very long chain fatty acids (fatty acids with greater than 22 carbon atoms; VLCFA) accumulate in peroxisomal disorders, but there is little information on their turnover in patients. To determine the suitability of using stable isotope-labeled VLCFA in patients with these disorders, the metabolism of 22-methyl[23,23,23-2H3]tricosanoic (iso-lignoceric) acid was studied in rats in vivo and in human skin fibroblasts in culture. The deuterated iso-VLCFA was degraded to the corresponding 16- and 18-carbon iso-fatty acids by rats in vivo and by normal human skin fibroblasts in culture, but there was little or no degradation in peroxisome-deficient (Zellweger’s syndrome) fibroblasts, indicating that its oxidation was peroxisomal. Neither the 14-, 20-, and 22-carbon iso-fatty acids nor the corresponding odd-chain metabolites could be detected. In the rat, the organ containing most of the iso-lignoceric acid, and its breakdown products, was the liver, whereas negligible amounts were detected in the brain, suggesting that little of the fatty acid crossed the blood-brain barrier. Our data indicate that VLCFA labeled with deuterium at the ω-position of the carbon chain are suitable derivatives for the in vivo investigation of patients with defects in peroxisomal β-oxidation because they are metabolized by the same pathways as the corresponding n-VLCFA. Moreover, as iso-VLCFA and their β-oxidation products are readily separated from the corresponding n-fatty acids by normal chromatographic procedures, the turnover of VLCFA can be more precisely measured. A preliminary report of part of this work (Reference 18) was presented at the 5th International Symposium on the Synthesis and Applications of Isotopes and Isotopically Labelled Compounds, Strasbourg, France, June 20–24, 1994.  相似文献   

18.
高效液相色谱法分析化妆品中微量成分的研究进展   总被引:1,自引:0,他引:1  
高尚芬 《日用化学工业》2006,36(6):379-383,400
综述了高效液相色谱法在化妆品中防腐剂、防晒剂中紫外线吸收剂以及性激素的检测等几个方面的应用;同时,介绍了分析所用的色谱柱、流动相、使用的检测手段以及样品的提取方法;最后针对目前存在的问题,提出了高效液相色谱用于化妆品中微量成分分析的研究方向和发展前景。  相似文献   

19.
In a coastal agricultural area in the central part of Japan (Shizuoka), we found decreasing nitrate concentration with depth in a shallow groundwater, where the depth to water table varied between 0.6 and 1.2 m below ground surface. High nitrate concentrations (5–29 mg N L–1) were often observed in the upper layer (0–2 m) of the groundwater, but the concentration decreased to less than 1 mg N L–1 in the deeper layer. Ammonium was scarcely detected, and the concentration of dissolved oxygen was usually low (< 1 mgO2 L–1) in the groundwater. Nitrate in the groundwater often had very heavy nitrogen stable isotope ratios (>20{}). There was a negative relationship between nitrogen stable isotope ratio of nitrate and its concentration. When nitrate was injected into the groundwater with acetylene and bromide (a conservative tracer), nitrate concentration decreased to 20% of the initial level within 5 days, accompanied by the increase in nitrite and nitrous oxide concentration and a little change in bromide concentration. These results indicate that microbial denitrification plays a potential role in the decrease of nitrate in shallow groundwater at the study site.  相似文献   

20.
我国硝酸工业生产技术新进展   总被引:1,自引:0,他引:1  
系统叙述了我国硝酸工业2000-2007年生产现状及主要技术成果,尤其指出了国产"四合一"机组的成功投运,使我国硝酸国产化装置取得较大的进步,表现在吨酸的铂耗、氨耗和能耗等方面接近国外引进装置水平,同时介绍了国外双加压法硝酸生产技术的进展.我国已成为硝酸生产大国,仍需以先进的技术改造和发展我国硝酸工业,确保我国硝酸工业健康有序地发展,加快从硝酸生产大国向强国迈进的步伐.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号