Non‐Fullerene Organic Solar Cells Based on Benzo[1,2‐b:4,5‐b′]difuran‐Conjugated Polymer with 14% Efficiency

The development of high‐performance donor polymers is important for obtaining high power conversion efficiencies (PCEs) of non‐fullerene polymer solar cells (PSCs). Currently, most high‐efficiency PSCs are fabricated with benzo[1,2‐b:4,5‐b′]dithiophene (BDT)‐based conjugated polymers. The photovoltaic performance of benzo[1,2‐b:4,5‐b′]difuran (BDF)‐based copolymers has lagged far behind that of BDT‐based counterparts. In this study, a novel BDF‐based copolymer L2 is designed and synthesized, in which BDF and benzotriazole (BTz) building blocks have been used as the electron‐sufficient and deficient units, respectively. When blending with a non‐fullerene small molecule acceptor (SMA), TTPT‐T‐4F, the L2‐based device exhibits a remarkably high PCE of 14.0%, which is higher than that of the device fabricated by its analogue BDT copolymer (12.72%). Moreover, PSCs based on the L2:TTPT‐T‐4F blend demonstrate excellent ambient stability with 92% of its original PCE remaining after storage in air for 1800 h. Thus, BDF is a promising electron‐donating unit, and the BDF‐based copolymers can be competitive or even surpass the performance of BDT‐based counterparts.     

A Chlorinated Donor Polymer Achieving High-Performance Organic Solar Cells with a Wide Range of Polymer Molecular Weight

In the field of non-fullerene organic solar cells (OSCs), compared to the rapid development of non-fullerene acceptors, the progress of high-performance donor polymers is relatively slow. The property and performance of donor polymers in OSCs are often sensitive to the molecular weight of the polymers. In this study, a chlorinated donor polymer named D18-Cl is reported, which can achieve high performance with a wide range of polymer molecular weight. The devices based on D18-Cl show a higher open-circuit voltage (V_OC) due to the slightly deeper energy levels and an outstanding short-circuit current density (J_SC) owing to the appropriate long periods of blend films and less ([6,6]-phenyl-C71-butyric acid methyl ester) (PC₇₁BM) in mixed domains, leading to the higher efficiency of 17.97% than those of the D18-based devices (17.21%). Meanwhile, D18-Cl can achieve high efficiencies (17.30–17.97%) when its number-averaged molecular weight (M_n) is ranged from 45 to 72 kDa. In contrast, the D18-based devices only exhibit relatively high efficiencies in a narrow M_n range of ≈70 kDa. Such property and performance make D18-Cl a promising donor polymer for scale-up and low-cost production.     

Atomic Optimization on Pyran-Fused Nonfullerene Acceptor Enables Organic Solar Cells With an Efficiency Approaching 16% and Reduced Energy Loss

Atomic replacement on platforms of nonfullerene acceptor (NFA) with already excellent performance is expected to further optimize the energy levels, absorptions, and even charge transfer dynamics of NFAs effectively without greatly destroying their superior molecular conformations. On the basis of high-performance F-series NFAs, the structural optimization at atomic level is performed by replacing sulfur atoms in FO-2Cl with selenium atoms, thus affording a new NFA labeled as FOSe-2Cl. FOSe-2Cl not only inherits the good planar configuration of FO-2Cl, but also exhibits more suitable energy levels, redshifted absorption, enhanced molecular packing, and accelerative charge transfer/transport dynamics compared with those of FO-2Cl. With a widely used polymer PM6 as the donor, organic solar cell (OSC) based on FOSe-2Cl affords a significantly improved power conversion efficiency (PCE) of 15.94% with a reduced energy loss (E_loss) of 0.670 eV, with respect to that of FO-2Cl-based OSC with a PCE of 14.94% and E_loss of 0.706 eV. The result represents the best performance reported to date for pyran-fused NFAs and F-series NFAs-based binary OSCs, providing another promising platform to achieve the state-of-the-art OSCs in addition to the well-known Y-series NFAs.     

High-Efficiency Organic Solar Cells Enabled by Non-Fullerene Acceptors with Benzimidazole as the Central Core

Electron-deficient central core plays a crucial role in the construction of efficient Y-series non-fullerene acceptors (NFAs). Here, fused-ring benzimidazole (BIm) served as a central core for the first time to yield a new NFA named MZ-1 and its structural analogue named MZ-2, which is obtained by replacing the methyl group on the 2C position of BIm in MZ-1 with trifluoromethyl group. Compared with MZ-1, MZ-2 shows obviously blue-shifted absorption and lowers the highest occupied molecular orbital (HOMO) energy level that is more matched to that of polymer donor PM6. Benefiting from the more efficient charge transport and favorable microphase separation morphology of the active layer, the acceptor MZ-2-based device affords an excellent power conversion efficiency (PCE) of 17.31% along with a high open-circuit voltage (V_oc) of 0.903 V, a short-circuit current density (J_sc) of 26.32 mA cm⁻² and a fill factor (FF) of 72.83%, which is remarkably superior to that of MZ-1-based devices with PCE of 10.70%. This study offers valuable insight into the design of acceptors to enrich Y series NFAs for high-performance organic solar cells (OSCs).     

Fibril Network Strategy Enables High‐Performance Semitransparent Organic Solar Cells

The development of semitransparent organic solar cells (ST‐OSCs) represents a significant step toward the commercialization of OSCs. However, the trade‐off between power conversion efficiency (PCE) and average visible transmittance (AVT) restricts further improvements of ST‐OSCs. Herein, it is demonstrated that a fibril network strategy can enable ST‐OSCs with a high PCE and AVT simultaneously. A wide‐bandgap polymer PBT1‐C‐2Cl that can self‐assemble into a fibril nanostructure is used as the donor and a near‐infrared small molecule Y6 is adopted as the acceptor. It is found that a tiny amount of PBT1‐C‐2Cl in the blend can form a high speed pathway for hole transport due to the well distributed fibril nanostructure, which increases the transmittance in the visible region. Meanwhile, the acceptor Y6 guarantees sufficient light absorption. Using this strategy, the optimized ST‐OSCs yield a high PCE of 9.1% with an AVT of over 40% and significant light utilization efficiency of 3.65% at donor/acceptor ratio of 0.25:1. This work demonstrates a simple and effective approach to realizing high PCE and AVT of ST‐OSCs simultaneously.     

Asymmetric Acceptors with Fluorine and Chlorine Substitution for Organic Solar Cells toward 16.83% Efficiency

Small‐molecule acceptors (SMAs)‐based organic solar cells (OSCs) have exhibited great potential for achieving high power conversion efficiencies (PCEs). Meanwhile, developing asymmetric SMAs to improve photovoltaic performance by modulating energy level distribution and morphology has drawn lots of attention. In this work, based on the high‐performance SMA (Y6), three asymmetric SMAs are developed by substituting the fluorine atoms on the terminal group with chlorine atoms, namely SY1 (two F atoms and one Cl atom), SY2 (two F atoms and two Cl atoms), and SY3 (three Cl atoms). Y6 (four F atoms) and Y6‐4Cl (four Cl atoms) are synthesized as control molecules. As a result, SY1 exhibits the shallowest lowest unoccupied molecular orbital energy level and the best molecular packing among these five acceptors. Consequently, OSCs based on PM6:SY1 yield a champion PCE of 16.83% with an open‐circuit voltage (V_OC) of 0.871 V, and a fill factor (FF) of 0.760, which is the best result among the five devices. The highest FF for the PM6:SY1‐based device is mainly ascribed to the most balanced charge transport and optimal morphology. This contribution provides deeper understanding of applying asymmetric molecule design method to further promote PCEs of OSCs.     

Efficient Hole Transfer via Delocalized Excited State in Small Molecular Acceptor: A Comparative Study on Photodynamics of PM6:Y6 and PM6:ITIC Organic Photovoltaic Blends

Organic solar cells (OSCs) based on small molecular acceptors (SMAs) have made great development with a power conversion efficiency (PCE) over 16% due to the design of novel materials and advances in device preparation technology. This work fabricates two bulk-heterojunction photovoltaic devices containing the same wide-bandgap donor PM6, respectively, matched with popular Y6 and ITIC SMAs. The PM6:Y6-based device achieves a much higher PCE of 15.21% than the PM6:ITIC-based device of 9.02%. On the basis of comparisons of macroscopic performances in the quasistatic regime, transient absorption spectroscopy (TAS) is further performed to better understand the microscopic dynamics difference in charge separation processes between the two photovoltaic blends. According to the TAS results, the calculated hole transfer efficiency in PM6:Y6 is 71.4%, far greater than the efficiency of 13.1% in PM6:ITIC, demonstrating favorable charge separation at donor/acceptor interfaces via hole transfer channel in PM6:Y6. The favorable hole transfer in PM6:Y6 is accounted for by its better mutual miscibility between the donor and acceptor, and the formation of long-lived delocalized intramoiety excimer state in the acceptor. These results highlight the important role of proper molecular design strategy with strong intermolecular coupling and beneficial film morphology on facilitating charge generation in OSCs adopting SMAs.     

Asymmetric and Halogenated Fused-Ring Electron Acceptor for Efficient Organic Solar Cells

Fused-ring non-fullerene electron acceptors (NFAs) boost the power conversion efficiencies (PCEs) of organic solar cells (OSCs). Asymmetric and halogenated NFAs have drawn increasing attention in recent years due to their unique optoelectronic properties. Starting from the symmetric NFA ITCC-M, this work systematically designs and synthesizes an asymmetric counterpart ITCC-M-2F, halogenated counterpart ITCC-Cl, and asymmetric and halogenated counterpart IDTT-Cl-2F. Among these NFAs, IDTT-Cl-2F shows the shallowest lowest unoccupied molecular orbital energy level, broader absorption range, and the tightest molecular packing. As a result, when blended with the donor PBDB-T-2Cl, IDTT-Cl-2F-based OSCs yield the highest PCE of 13.3% with an open-circuit voltage of 0.96 V, short-circuit current of 19.20 mA cm^–2, and fill factor of 71.1%, which is the highest PCE of OSCs employing 2-(2-chloro-6-oxo-5,6-dihydro-4H-cyclopenta[b]thiophen-4-ylidene) malononitrile (ClIC) unit terminated NFA. The results demonstrate the synergistic effect of asymmetry and halogenation toward tuning of the optoelectronic properties of NFAs for high performance OSCs.     

Ternary Blend Strategy for Achieving High‐Efficiency Organic Solar Cells with Nonfullerene Acceptors Involved

Nonfullerene acceptors have recently drawn considerable attention in bulk heterojunction organic solar cells (OSCs). The power conversion efficiency (PCE) over 14% is achieved in single‐junction fullerene‐free OSCs, which has surpassed that of fullerene‐based counterparts. For future commercial applications, however, a high and stable PCE > 15% is required, which entails rational material design and device optimization. In this context, three approaches are generally utilized—the synthesis of novel nonfullerene acceptors and the selection of suitable polymer donors to pair with them, the tandem or multijunction device architecture, and the ternary blend strategy. Compared to the former two methods, the ternary strategy allows to employ the existing photovoltaic materials and the single‐junction device. Therefore, an exploration of nonfullerene acceptor–based ternary blend OSCs (NFTSCs) has shown unprecedented progress since 2016. This review summarizes and classifies the photovoltaic materials utilized in NFTSCs, aiming to not only exhibit the recent development of NFTSCs but also elucidate the correlation among donor/acceptor materials, film morphology, transport dynamics, and device fabrication toward high‐efficiency OSCs. Lastly, the above key advances are highlighted along with the existing issues and insights into the viable path for the further research thrusts are offered.     

High-Efficiency Organic Solar Cells Enabled by Chalcogen Containing Branched Chain Engineering: Balancing Short-Circuit Current and Open-Circuit Voltage,Enhancing Fill Factor

The elaborate balance between the open-circuit voltage (V_OC) and the short-circuit current density (J_SC) is critical to ensure efficient organic solar cells (OSCs). Herein, the chalcogen containing branched chain engineering is employed to address this dilemma. Three novel nonfullerene acceptors (NFAs), named BTP-2O , BTP-O-S , and BTP-2S , featuring different peripheral chalcogen containing branched chains are synthesized. Compared with symmetric BTP-2O and BTP-2S grafting two alkoxy or alkylthio branched chains, the asymmetric BTP-O-S grafting one alkoxy and one alkylthio branched chains shows mediate absorption range, applicable miscibility, and favorable crystallinity. Benefiting from the enhanced π–π stacking and charge transport, an optimal power conversion efficiency (PCE) of 17.3% is obtained for the PM6: BTP-O-S -based devices, with a good balance between V_OC (0.912 V) and J_SC (24.5 mA cm⁻²), and a high fill factor (FF) of 0.775, which is much higher than those of BTP-2O (16.1%) and BTP-2S -based (16.4%) devices. Such a result represents one of the highest efficiencies among the binary OSCs with V_OC surpassing 0.9 V. Moreover, the BTP-O-S -based devices fabricated by using green solvent yield a satisfactory PCE of 17.1%. This work highlights the synergistic effect of alkoxy and alkylthio branched chains for high-performance OSCs by alleviating voltage loss and enhancing FF.     

Fluorobenzotriazole (FTAZ)‐Based Polymer Donor Enables Organic Solar Cells Exceeding 12% Efficiency

The fluorobenzotriazole (FTAZ)‐based copolymer donors are promising candidates for nonfullerene polymer solar cells (PSCs), but suffer from relatively low photovoltaic performance due to their unsuitable energy levels and unfavorable morphology. Herein, three polymer donors, L24 , L68 , and L810 , based on a chlorinated‐thienyl benzodithiophene (BDT‐2Cl) unit and FTAZ with different branched alkyl side chain, are synthesized. Incorporation of a chlorine (Cl) atom into the BDT unit is found to distinctly optimize the molecular planarity, energy levels, and improve the polymerization activity. Impressively, subtle side chain length of FTAZ realizes a dramatic improvement in all the device parameters, as revealed by the short‐current density (J_sc) improved from 7.41 to 20.76 mA cm^?2, fill‐factor from 36.3 to 73.5%, and even the open‐circuit voltage (V_oc) from 0.495 to 0.790 V. The best power conversion efficiency (PCE) of 12.1% is obtained from the L810‐based device, which is one of the highest values reported for FTAZ‐based PSCs so far. Notably, the corresponding external quantum efficiency curve keeps a very prominent value up to 80% from 500 to 800 nm. The notable performance is discovered from the reduced energy loss, improved molecular face‐on orientation, the down‐shifted energy levels, and optimized absorption coefficient regulated by side‐chain engineering.     

Non-fullerene acceptors based on multiple non-covalent interactions for low cost and air stable organic solar cells

Significant progresses have been made on organic solar cells (OSCs) in last few years, but the industrialization of OSCs is still hindered by high cost and poor device stability. Recently, the most successful OSCs are usually based on fused-ring small molecule non-fullerene acceptors (SM-NFAs) which often involve multiple complex synthetic steps and result in low overall yields and high cost. Herein, two easily accessible non-fused NFAs based on BT, CPDT and IC with different halogen atoms named BT-F and BT-Cl were designed and synthesized. Non-covalent interactions or conformation locks between BT and adjacent CPDT units provided planar conformations, which is beneficial for molecular packing and charge transport. When blended with low cost polymer donor PTQ-10, optimal devices based on BT-F provided a PCE of 8.26%. A higher PCE of 8.65% was obtained from BT-Cl-based devices. Low voltage loss of 0.57 and 0.59 V were observed for BT-F- and BT-Cl-based devices. It is noteworthy that devices based on PTQ-10:BT-F and PTQ-10:BT-Cl exhibited excellent stabilities when stored in ambient atmosphere for 10 days without encapsulation. This work demonstrates an example of pursuing low cost OSCs with excellent air stability.     

High performance ternary organic solar cells using two miscible donor molecules based on PTB7-Th and DR3TBDTT

The recent stunning rise in power conversion efficiencies (PCEs) of ternary organic solar cells (OSCs) has triggered much attention. However, achieving high PCE values are quite challenging because the ternary system is complicated on phase separation behavior. In this work, ternary organic solar cells (OSCs) with one acceptor (PC₇₁BM) and two donors, i.e., one polymer (PTB7-Th) and one small molecule (DR3TBDTT) have been fabricated. We substantially improved PCE from the best reported value of 7.53%–9.25% with increase of 22.8%, and an averaged PCE of 9.25% is obtained due to the improvement of the fill factor (FF) and the short-circuit current density (J_sc). The results of atomic force microscopy (AFM) indicate that a highly ordered molecular compatibility could be obtained by forming alloy with two miscible donors, and the doping of DR3TBDTT not only protects the long distance charge transport in the original binary system, but also improves the size of phase separation of the active layer within the ternary OSCs, thus forming the ordered nano morphology, which can improve the mobility of hole and reduce the charge recombination.     

Conformation Locking on Fused‐Ring Electron Acceptor for High‐Performance Nonfullerene Organic Solar Cells

In this work, sidechain engineering on conjugated fused‐ring acceptors for conformation locking is demonstrated as an effective molecular design strategy for high‐performance nonfullerene organic solar cells (OSCs). A novel nonfullerene acceptor (ITC6‐IC) is designed and developed by introducing long alkyl chains into the terminal electron‐donating building blocks. ITC6‐IC has achieved definite conformation with a planar structure and better solubility in common organic solvents. The weak electron‐donating hexyl upshifts the lowest unoccupied molecular orbital level of ITC6‐IC, resulting in a higher V_OC in comparison to the widely used ITIC. The OSCs based on PBDB‐T:ITC6‐IC reveal a promising power conversion efficiency of 11.61% and an expected high V_OC of 0.97 V. The weaker π–π stacking induced by steric hindrance affords ITC6‐IC with enhanced compatibility with polymer donors. The blend film treated with suitable thermal annealing exhibits a fibril crystallization feature with a good bicontinuous network morphology. The results indicate that the molecular design approach of ITC6‐IC can be inspirational for future development of nonfullerene acceptors for high efficiency OSCs.     

A 2.20 eV Bandgap Polymer Donor for Efficient Colorful Semitransparent Organic Solar Cells

Semitransparent organic solar cells (ST-OSCs) have attracted increasing attention due to their promising prospect in building-integrated photovoltaics. Generally, efficient ST-OSCs with good average visible transmittance (AVT) can be realized by developing active layer materials with light absorption far from the visible light range. Herein, the development of ultrawide bandgap polymer donors with near-ultraviolet absorption, paired with near-infrared acceptors, is proposed to achieve high-performance ST-OSCs. The key points for the design of ultrawide bandgap polymers include constructing donor–donor type conjugated skeleton, suppressing the quinoidal resonance effect, and minimizing the twist of conjugated skeleton via noncovalent conformational locks. As a proof of concept, a polymer named PBOF with an optical bandgap of 2.20 eV is synthesized, which exhibited largely reduced overlap with the human eye photopic response spectrum and afforded a power conversion efficiency (PCE) of 16.40% in opaque device. As a result, ST-OSCs with a PCE over 10% and an AVT over 30% are achieved without optical modulation. Moreover, colorful ST-OSCs with visual aesthetics can be achieved by tuning the donor/acceptor weight ratio in active layer benefiting from the ultrawide bandgap nature of PBOF. This study demonstrates the great potential of ultrawide bandgap polymers for efficient colorful ST-OSCs.     

Effects of Halogenation of Small-Molecule and Polymeric Acceptors for Efficient Organic Solar Cells

Tuning the properties of non-fullerene acceptors (NFAs) through halogenation, including fluorination and chlorination, represents one of the most promising strategies to boost the performance of organic solar cells (OSCs). However, it remains unclear how the F and Cl choice influences the molecular packing and performance between small-molecule and polymeric acceptors. Here, a series of small-molecule and polymeric acceptors with different amounts and types of halogenation is synthesized, and the effects of fluorination and chlorination between small-molecule and polymeric acceptors are investigated. It is found that chlorinated small-molecule acceptors lead to longer exciton diffusion length and better performance compared to the corresponding fluorinated ones, which attributes to their stronger intermolecular packing mode. For polymer acceptors, in contrast, the fluorinated polymers achieve a denser packing mode and better performance, because chlorinated polymers exhibit reduced intrachain conjugation between end group moieties and linker units. This study demonstrates different halogenation effects on the packing modes and performances for small-molecule and polymeric acceptors, which provides important guidance for the molecule design of high-performance acceptors for OSCs.     

D18,an eximious solar polymer!

Organic solar cell(OSC)is a promising photovoltaic technology with great commercialization potential due to the advantages like solution-processing,roll-to-roll fabrication,lightweight,flexibility,and semitransparency[1?7].Conjugated polymer donors are key materials for OSCs[8].     

Efficient and Scalable Large-Area Organic Solar Cells by Asymmetric Nonfullerene Acceptors Based on 9H-Indeno[1,2-b]pyrazine-2,3,8-Tricarbonitrile

It remains challenging to fabricate efficient, scalable large-area organic solar cells (OSCs) owing to the unfavorable morphology of photoactive blend films. To address this challenge, two asymmetric nonfullerene acceptors (NFAs) IPC1CN-BBO-IC2F and IPC1CN-BBO-IC2Cl are synthesized, where 12,13-bis(2-butyloctyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2′“,3′”:4′,5′]thieno[2′,3′:4,5]pyrrolo[3,2-g]thieno[2′,3′:4,5]thieno-[3,2-b]indole (BBO) is the molecular core, and two types of end groups are appended to its ends, namely the 9H-indeno[1,2-b]pyrazine-2,3,8-tricarbonitrile (IPC1CN) end group and one of 2-(5,6-dihalo-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile end groups (IC2F or IC2Cl). These NFAs facilitate effective tuning of light absorption and energy levels, offer high carrier mobilities, and allow for the formation of appropriate morphologies. Note that these benefits apply even to large-area devices, unlike typical Y6-based NFAs. In addition, a random copolymer PM6-PBDBT(55) is synthesized and its energy levels are optimally matched with those of the asymmetric NFAs. The blade-coated 1 cm²-area OSCs based on PM6-PBDBT(55):IPC1CN-BBO-IC2Cl exhibit a PCE of 14.12%, which is higher than that of PM6-PBDBT(55)-IPC1CN-BBO-IC2F-based OSCs. More importantly, the PM6-PBDBT(55):IPC1CN-BBO-IC2Cl-based large-area (58.50 cm²) modules yield an impressive PCE of 11.28% with a small cell-to-module loss in fill factor. These results suggest that a combination of the asymmetric molecular design using the IPC1CN group and the terpolymer strategy will pave a new path for fabricating highly efficient and scalable large-area OSCs.     

A two-dimension-conjugated small molecule for efficient ternary organic solar cells

Ternary organic solar cells (OSCs) are burgeoning as one of the effective strategies to achieve high power conversion efficiencies (PCEs) by incorporating a third component with a complementary absorption into the binary blends. In this study, we presented a new two-dimension-conjugated small molecule denoted by DR3TBDTTVT, which alone gave rise to a best PCE of 5.71% with acceptor PC₇₁BM as active layer. Given the complementary absorption with PTB7-Th, DR3TBDTTVT was doped into (PTB7-Th:PC₇₁BM)-based binary blends, and ternary OSCs were developed. The ternary OSCs with 10 wt% of DR3TBDTTVT displayed improved hole-mobility, reduced device resistance and better phase separation of active layer, thus leading to an impressive PCE of 7.77% with open-circuit voltage of 0.77 V, short-circuit density of 14.52 mA cm⁻² and fill factor of 70.3%. Ternary OSCs well make up for the light-harvesting insufficiency of binary OSCs, and this research provides a new material for the improvement of PCEs for single-junction OSCs.     

A Regularity-Based Fullerene Interfacial Layer for Efficient and Stable Perovskite Solar Cells via Blade-Coating

The electron transport layer (ETL) plays a crucial part in extracting electron carriers while optimizing the interfacial contact of perovskite/electrode in planar heterojunction perovskite solar cells (PVSCs). Despite various ETLs being designed for efficient PVSCs, there exists hardly any research on the effect of molecular stacking order on device performance. Herein, poly(ethylene-co-vinyl acetate) (EVA) is employed as the [6,6]-phenyl-C₆₁-butyric acid methyl ester (PC₆₁BM) solution additive. The strong binding energy between EVA with PC₆₁BM promotes the molecular stacking order of ETLs, which alleviates the morphology inhomogeneity, possesses a matched energy level, blocks ion migration, and improves the water–oxygen barrier of perovskite devices. The blade-coated MAPbI₃-based PVSCs achieve a power conversion efficiency (PCE) of 19.32% with positive reproducibility and negligible hysteresis, as well as maintain 90% and 80% of the initial PCE after storage under inert and ambient conditions (52% humidity) for 1500 h without encapsulation. This strategy also improves the champion PCE of CsFAMA-based PVSCs to 20.33%. These findings demonstrate that the regulation of molecular stacking order is a valid approach to optimize interfacial charge-carrier recombination in PVSCs, which meet the demand for high-performance ETL in large-area PVSCs and improve the upscaling of the fabrication technology toward practical applications.