In Situ Growth of 2D Perovskite Capping Layer for Stable and Efficient Perovskite Solar Cells

2D halide perovskites have recently been recognized as a promising avenue in perovskite solar cells (PSCs) in terms of encouraging stability and defect passivation effect. However, the efficiency (less than 15%) of ultrastable 2D Ruddlesden–Popper PSCs still lag far behind their traditional 3D perovskite counterparts. Here, a rationally designed 2D‐3D perovskite stacking‐layered architecture by in situ growing 2D PEA₂PbI₄ capping layers on top of 3D perovskite film, which drastically improves the stability of PSCs without compromising their high performance, is reported. Such a 2D perovskite capping layer induces larger Fermi‐level splitting in the 2D‐3D perovskite film under light illumination, resulting in an enhanced open‐circuit voltage (V_oc) and thus a higher efficiency of 18.51% in the 2D‐3D PSCs. Time‐resolved photoluminescence decay measurements indicate the facilitated hole extraction in the 2D‐3D stacking‐layered perovskite films, which is ascribed to the optimized energy band alignment and reduced nonradiative recombination at the subgap states. Benefiting from the high moisture resistivity as well as suppressed ion migration of the 2D perovskite, the 2D‐3D PSCs show significantly improved long‐term stability, retaining nearly 90% of the initial power conversion efficiency after 1000 h exposure in the ambient conditions with a high relative humidity level of 60 ± 10%.     

Self‐Crystallized Multifunctional 2D Perovskite for Efficient and Stable Perovskite Solar Cells

Recently, perovskite solar cells (PSC) with high power‐conversion efficiency (PCE) and long‐term stability have been achieved by employing 2D perovskite layers on 3D perovskite light absorbers. However, in‐depth studies on the material and the interface between the two perovskite layers are still required to understand the role of the 2D perovskite in PSCs. Self‐crystallization of 2D perovskite is successfully induced by deposition of benzyl ammonium iodide (BnAI) on top of a 3D perovskite light absorber. The self‐crystallized 2D perovskite can perform a multifunctional role in facilitating hole transfer, owing to its random crystalline orientation and passivating traps in the 3D perovskite. The use of the multifunctional 2D perovskite (M2P) leads to improvement in PCE and long‐term stability of PSCs both with and without organic hole transporting material (HTM), 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenyl‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) compared to the devices without the M2P.     

Side-Chain Functionalized Polymer Hole-Transporting Materials with Defect Passivation Effect for Highly Efficient Inverted Quasi-2D Perovskite Solar Cells

Compared with inverted 3D perovskite solar cell (PSCs), inverted quasi-2D PSCs have advantages in device stability, but the device efficiency is still lagging behind. Constructing polymer hole-transporting materials (HTMs) with passivation functions to improve the buried interface and crystallization properties of perovskite films is one of the effective strategies to improve the performance of inverted quasi-2D PSCs. Herein, two novel side-chain functionalized polymer HTMs containing methylthio-based passivation groups are designed, named PVCz-SMeTPA and PVCz-SMeDAD, for inverted quasi-2D PSCs. Benefited from the non-conjugated flexible backbone bearing functionalized side-chain groups, the polymer HTMs exhibit excellent film-forming properties, well-matched energy levels and improved charge mobility, which facilitates the charge extraction and transport between HTM and quasi-2D perovskite layer. More importantly, by introducing methylthio units, the polymer HTMs can enhance the contact and interactions with quasi-2D perovskite, and further passivating the buried interface defects and assisting the deposition of high-quality perovskite. Due to the suppressed interfacial non-radiative recombination, the inverted quasi-2D PSCs using PVCz-SMeTPA and PVCz-SMeDAD achieve impressive power conversion efficiency (PCE) of 21.41% and 20.63% with open-circuit voltage of 1.23 and 1.22 V, respectively. Furthermore, the PVCz-SMeTPA based inverted quasi-2D PSCs also exhibits negligible hysteresis and considerably improved thermal and long-term stability.     

Integrated Quasi-2D Perovskite/Organic Solar Cells with Efficiency over 19% Promoted by Interface Passivation

Integrated perovskite/organic solar cells (IPOSCs) have shown great potential in broadening the light absorption range and improving the photovoltaic performance. However, the severe interface charge recombination and unmatched energy levels between perovskite and organic photoactive layers hinder their performance improvement. Here, an efficient interface passivation strategy for IPOSCs based on a layered Ruddlesden–Popper (RP) perovskite and high photovoltaic performance is successfully demonstrated. It is found that an ultrathin conjugated polymer (PM6) layer could passivate the surface defects of perovskite film, tuning the energy level and suppress the nonradiative recombination loss, leading to efficient interface contact between RP perovskite and organic photoactive layers, boosting the open-circuit voltage from 1.06 to 1.12 V and the efficiency from 17.23% to 19.15%. Importantly, the optimized device shows extended photocurrent response to 930 nm with a peak intensity close to 50% from 800 to 931 nm. The results indicate that interface passivation using a functionalized polymer could be an efficient strategy to improve the photovoltaic performance of integrated devices.     

Double‐Sided Surface Passivation of 3D Perovskite Film for High‐Efficiency Mixed‐Dimensional Perovskite Solar Cells

Defect‐mediated carrier recombination at the interfaces between perovskite and neighboring charge transport layers limits the efficiency of most state‐of‐the‐art perovskite solar cells. Passivation of interfacial defects is thus essential for attaining cell efficiencies close to the theoretical limit. In this work, a novel double‐sided passivation of 3D perovskite films is demonstrated with thin surface layers of bulky organic cation–based halide compound forming 2D layered perovskite. Highly efficient (22.77%) mixed‐dimensional perovskite devices with a remarkable open‐circuit voltage of 1.2 V are reported for a perovskite film having an optical bandgap of ≈1.6 eV. Using a combination of experimental and numerical analyses, it is shown that the double‐sided surface layers provide effective defect passivation at both the electron and hole transport layer interfaces, suppressing surface recombination on both sides of the active layer. Despite the semi‐insulating nature of the passivation layers, an increase in the fill factor of optimized cells is observed. The efficient carrier extraction is explained by incomplete surface coverage of the 2D perovskite layer, allowing charge transport through localized unpassivated regions, similar to tunnel‐oxide passivation layers used in silicon photovoltaics. Optimization of the defect passivation properties of these films has the potential to further increase cell efficiencies.     

Modulation on Electrostatic Potential of Passivator for Highly Efficient and Stable Perovskite Solar Cells

The perovskite layer contains a large number of charged defects that seriously impair the efficiency and stability of perovskite solar cells (PSCs), thus it is essential to develop an effective passivation strategy to heal them. Based on theoretical calculations, it is found that enhancing the electrostatic potential of passivators can improve passivation effect and adsorption energy between charged defects and passivators. Herein, an electrostatic potential modulation (EPM) strategy is developed to design passivators for highly efficient and stable PSCs. With the EPM strategy, 1-phenylethylbiguanide (PEBG) and 1-phenylbiguanide (PBG) are designed. It is found that the charge distribution and electrostatic potential of phenyl- and phenylethyl- substituent on the biguanide are significantly enhanced. The N atom directly bonding to the phenyl group shows larger positive charge than that bonding to the phenylethyl group. The modulated electrostatic potential makes PBG bind stronger with the defects on perovskite surface. Based on the effective passivation of EPM, a champion efficiency of 24.67% is realized and the device retain 91.5% of its initial PCE after ≈1300 h. The promising EPM strategy, which provides a principle of passivator design and allows passivation to be controllable, may advance further optimization and application of perovskite solar cells toward commercialization.     

Surface Reconstruction Engineering with Synergistic Effect of Mixed-Salt Passivation Treatment toward Efficient and Stable Perovskite Solar Cells

Surface passivation treatment is a widely used strategy to resolve trap-mediated nonradiative recombination toward high-efficiency metal-halide perovskite photovoltaics. However, a lack of passivation with mixture treatment has been investigated, as well as an in-depth understanding of its passivation mechanism. Here, a systematic study on a mixed-salt passivation strategy of formamidinium bromide (FABr) coupled with different F-substituted alkyl lengths of ammonium iodide is demonstrated. It is obtained better device performance with decreasing chain length of the F-substituted alkyl ammonium iodide in the presence of FABr. Moreover, they unraveled a synergistic passivation mechanism of the mixed-salt treatment through surface reconstruction engineering, where FABr dominates the reformation of the perovskite surface via reacting with the excess PbI₂. Meanwhile, ammonium iodide passivates the perovskite grain boundaries both on the surface and top perovskite bulk through penetration. This synergistic passivation engineer results in a high-quality perovskite surface with fewer defects and suppressed ion migration, leading to a champion efficiency of 23.5% with mixed-salt treatment. In addition, the introduction of the moisture resisted F-substituted groups presents a more hydrophobic perovskite surface, thus enabling the decorated devices with excellent long-term stability under a high humid atmosphere as well as operational conditions.     

Undoped Hole Transport Layer Toward Efficient and Stable Inorganic Perovskite Solar Cells

Numerous strategies have been practiced to improve the power conversion efficiency of CsPbI₂Br-based perovskite solar cells (PSCs), which definitely makes efficiency gradually approach the theoretical efficiency limit. However, sufficient device stability is still in urgent demand for commercialization, pushing to overcome some instability sources induced by hygroscopicity of spiro-OMeTAD and residual strain of perovskite layer. To address these issues, p-type semiconductor of PCPDTBT is used to replace spiro-OMeTAD, enabling dual functions of hole transport and strain regulation. On the one hand, undoped PCPDTBT performs excellent hole extraction and transport, while avoiding the perovskite degradation caused by the hygroscopicity of common additives. On the other hand, PCPDTBT assisted by a thermally spin-coating method compensates for the thermally-induced residual strain in perovskite layer owing to its high thermal expansion coefficient. Consequently, CsPbI₂Br-based PSCs with PCPDTBT layer achieve improved efficiency of 16.5% as well as enhanced stability. This study provides a simple and facile strategy to achieve efficient and stable CsPbI₂Br-based PSCs.     

Phenylhydrazinium Iodide for Surface Passivation and Defects Suppression in Perovskite Solar Cells

In recent years, hybrid perovskite solar cells (HPSCs) have received considerable research attention due to their impressive photovoltaic performance and low‐temperature solution processing capability. However, there remain challenges related to defect passivation and enhancing the charge carrier dynamics of the perovskites, to further increase the power conversion efficiency of HPSCs. In this work, the use of a novel material, phenylhydrazinium iodide (PHAI), as an additive in MAPbI₃ perovskite for defect minimization and enhancement of the charge carrier dynamics of inverted HPSCs is reported. Incorporation of the PHAI in perovskite precursor solution facilitates controlled crystallization, higher carrier lifetime, as well as less recombination. In addition, PHAI additive treated HPSCs exhibit lower density of filled trap states (10¹⁰ cm^?2) in perovskite grain boundaries, higher charge carrier mobility (≈11 × 10^?4 cm² V^?1 s), and enhanced power conversion efficiency (≈18%) that corresponds to a ≈20% improvement in comparison to the pristine devices.     

2D Perovskite Seeding Layer for Efficient Air‐Processable and Stable Planar Perovskite Solar Cells

Despite the record power conversion efficiencies, inverted perovskite solar cells (PSCs) are still looking to overcome the challenge of moisture instability. This is mitigated by introducing 2D perovskite at the base of a 3D perovskite via coating of ethylenediamine bications on top of the hole transport layer of p–i–n planar configured devices. The cations induce thin 2D perovskite growth beneath the 3D perovskite to create a 2D/3D hybrid active layer. This 2D layer in turn acts as a template for the growth of relatively large grains compared to that of pure 3D perovskite films. This stems from the merging of grain boundaries. The hydrophobicity of the 2D/3D perovskite film consequently improves, as evidenced by a large contact angle of 93.1°, compared to 68.9° for the 3D perovskite film. Because there are fewer defects sourced from grain boundaries, the air‐processed 2D/3D perovskite devices yield a high power conversion efficiency of 15.02%, compared to 13.10% from 3D perovskite devices. When stored in moderately humid environment of 55% relative humidity, the 2D/3D devices exhibit longer stabilities, with 75% of their power conversion efficiencies maintained after 150 h, compared to a total loss in efficiency for 3D device in the same time frame.     

Rapid Crystallization for Efficient 2D Ruddlesden–Popper (2DRP) Perovskite Solar Cells

Due to the additional introduction of bulky organic ammonium and the competition between bulky organic ammonium and methyl ammonium in 2D Ruddlesden‐Popper (2DRP) perovskite, the crystallization process becomes complicated. Here, it is demonstrated that the rapid crystallization controlled by processing solvents plays an important role in achieving high‐quality 2DRP perovskite films. It is found that the processing solvents, e.g., dimethylacetamide (DMAC), N,N‐dimethylformamide (DMF), and dimethyl sulfoxide (DMSO), with a different polarity and boiling point, have almost no effect on crystal structure and phase distribution but have a remarkable effect on crystallization kinetics, crystal growth orientation, and crystallinity of 2DRP perovskite. Compared to polar aprotic solvent DMF and DMSO with a high boiling point, DMAC with low polarity and a suitable boiling point has a weak coordination to lead and ammonium salts and is easy to escape during solution processing, which is able to accelerate the crystallization rate of 2DRP perovskite. Benefitting from the rapid crystallization enabled high‐quality 2DRP perovskite films, the best‐performing device with improved stability and a power conversion efficiency of 12.15% is obtained using DMAC solvent. These findings may give guidance for solvent engineering for highly efficient 2DRP perovskite solar cells in the future.     

Multifunctional Enhancement for Highly Stable and Efficient Perovskite Solar Cells

With a certified efficiency as high as 25.2%, perovskite has taken the crown as the highest efficiency thin film solar cell material. Unfortunately, serious instability issues must be resolved before perovskite solar cells (PSCs) are commercialized. Aided by theoretical calculation, an appropriate multifunctional molecule, 2,2-difluoropropanediamide (DFPDA), is selected to ameliorate all the instability issues. Specifically, the carbonyl groups in DFPDA form chemical bonds with Pb²⁺ and passivate under-coordinated Pb²⁺ defects. Consequently, the perovskite crystallization rate is reduced and high-quality films are produced with fewer defects. The amino groups not only bind with iodide to suppress ion migration but also increase the electron density on the carbonyl groups to further enhance their passivation effect. Furthermore, the fluorine groups in DFPDA form both an effective barrier on the perovskite to improve its moisture stability and a bridge between the perovskite and HTL for effective charge transport. In addition, they show an effective doping effect in the HTL to improve its carrier mobility. With the help of the combined effects of these groups in DFPDA, the PSCs with DFPDA additive achieve a champion efficiency of 22.21% and a substantially improved stability against moisture, heat, and light.     

Low-Dimensional 2-thiopheneethylammonium Lead Halide Capping Layer Enables Efficient Single-Junction Methylamine-Free Wide-Bandgap and Tandem Perovskite Solar Cells

Wide-bandgap (WBG) perovskite solar cells (PSCs) have garnered significant attention for their potential applications in tandem solar cells. However, their large open-circuit voltage (V_OC) deficit and serious photo-induced halide segregation remain the main challenges that impede their applications. Herein, a post-treatment strategy without thermal annealing is presented to form a 2D top layer of 2-thiopheneethylammonium lead halide (n = 1) on WBG perovskites. This thermal annealing-free post-treatment method can more effectively passivate the defects of WBG methylamine (MA)-free formamidinium/cesium lead iodide/bromide perovskite films and suppress photo-induced perovskite phase segregation, as compared with the thermal annealing method that yields multi-2D phases. The resulting opaque and semi-transparent 1.66 eV-bandgap perovskite solar cells deliver maximum power conversion efficiencies of 21.47% (a small V_OC deficit of 0.43 V) and 19.11%, respectively, both of which are among the highest reports for inverted MA-free WBG PSCs. Consequently, four-terminal all-perovskite tandem cells realize a remarkable efficiency of 26.64%, showing great promise for their applications in efficient multi-junction tandem solar cells.     

Efficient and Stable Perovskite Solar Cells via Dual Functionalization of Dopamine Semiquinone Radical with Improved Trap Passivation Capabilities

Highly efficient planar heterojunction perovskite solar cells (PVSCs) with dopamine (DA) semiquinone radical modified poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (DA‐PEDOT:PSS) as a hole transporting layer (HTL) were fabricated. A combination of characterization techniques were employed to investigate the effects of DA doping on the electron donating capability of DA‐PEDOT:PSS, perovskite film quality and charge recombination kinetics in the solar cells. Our study shows that DA doping endows the DA‐PEDOT:PSS‐modified PVSCs with a higher radical content and greater perovskite to HTL charge extraction capability. In addition, the DA doping also improves work function of the HTL, increases perovskite film crystallinity, and the amino and hydroxyl groups in DA can interact with the undercoordinated Pb atoms on the perovskite crystal, reducing charge‐recombination rate and increasing charge‐extraction efficiency. Therefore, the DA‐PEDOT:PSS‐modified solar cells outperform those based on PEDOT:PSS, increasing open‐circuit voltage (V _oc) and power conversion efficiency (PCE) to 1.08 V and 18.5%, respectively. Even more importantly, the efficiency of the unencapsulated DA‐PEDOT:PSS‐based PVSCs are well retained with only 20% PCE loss after exposure to air for 250 hours. These in‐depth insights into structure and performance provide clear and novel guidelines for the design of effective HTLs to facilitate the practical application of inverted planar heterojunction PVSCs.     

Interfacial Energy Level Alignment and Defect Passivation by Using a Multifunctional Molecular for Efficient and Stable Perovskite Solar Cells

Tin oxide (SnO₂) is currently the dominating electron transport material (ETL) used in state-of-the-art perovskite solar cells (PSCs). However, there are amounts of defects distributed at the interface between ETL and perovskite to deteriorate PSC performance. Herein, a molecule bridging layer is built by incorporating 2,5-dichloroterephthalic acid (DCTPA) into the interface between the SnO₂ and perovskites to achieve better energy level alignment and superior interfacial contact. The multifunctional molecular bridging layer not only can passivate the trap states of Sn dangling bonds and oxygen vacancies resulting in improved conductivity and the electron extraction of SnO₂ but also can regulate the perovskite crystal growth and reduce defect-assisted nonradiative recombination due to its strong interaction with undercoordinated lead ions. As a result, the DCTPA-modified PSCs achieve champion power conversion efficiencies (PCEs) of 23.25% and 20.23% for an active area of 0.15 cm² device and 17.52 cm² mini-module, respectively. Moreover, the perovskite films and PSCs based on DCTPA modification show excellent long-term stability. The unencapsulated target device can maintain over 90% of the initial PCE after 1000 h under ambient air. This strategy guides design methods of molecule bridging layer at the interface between SnO₂ and perovskite to improve the performance of PSCs .     

Aryl Diammonium Iodide Passivation for Efficient and Stable Hybrid Organ‐Inorganic Perovskite Solar Cells

Surface passivation is increasingly one of the most prominent strategies to promote the efficiency and stability of perovskite solar cells (PSCs). However, most passivation molecules hinder carrier extraction due to poorly conductive aggregation between perovskite surface and carrier transportation layer. Herein, a novel molecule: p‐phenyl dimethylammonium iodide (PDMAI) with ammonium group on both terminals is introduced, and its passivation effect is systematically investigated. It is found that PDMAI can mitigate defects at the surface and promote carrier extraction from perovskite to the hole transporting layer, leading to a lift of open‐circuit voltage of 40 mV. Profiting from superior PDMAI passivation, the average efficiency of PSCs has been elevated from 19.69% to 20.99%. As demonstrated with density functional theory calculations, PDMAI probably tends to anchor onto the perovskite surface with both ? NH₃I tails, and enhances the adhesion and contact to perovskite layer. The exposed hydrophobic aryl core protects perovskite against detrimental environmental factors. In addition, the alkyl component between aryl and ammonium groups is demonstrated to be essentially vital in triggering passivation function, which offers the guidance for the design of passivation molecules.     

Passivated Perovskite Crystallization via g‐C3N4 for High‐Performance Solar Cells

Organometallic halide perovskite films with good surface morphology and large grain size are desirable for obtaining high‐performance photovoltaic devices. However, defects and related trap sites are generated inevitably at grain boundaries and on surfaces of solution‐processed polycrystalline perovskite films. Seeking facial and efficient methods to passivate the perovskite film for minimizing defect density is necessary for further improving the photovoltaic performance. Here, a convenient strategy is developed to improve perovskite crystallization by incorporating a 2D polymeric material of graphitic carbon nitride (g‐C₃N₄) into the perovskite layer. The addition of g‐C₃N₄ results in improved crystalline quality of perovskite film with large grain size by retarding the crystallization rate, and reduced intrinsic defect density by passivating charge recombination centers around the grain boundaries. In addition, g‐C₃N₄ doping increases the film conductivity of perovskite layer, which is beneficial for charge transport in perovskite light‐absorption layer. Consequently, a champion device with a maximum power conversion efficiency of 19.49% is approached owing to a remarkable improvement in fill factor from 0.65 to 0.74. This finding demonstrates a simple method to passivate the perovskite film by controlling the crystallization and reducing the defect density.     

Expanded Phase Distribution in Low Average Layer-Number 2D Perovskite Films: Toward Efficient Semitransparent Solar Cells

The application of low average layer-number (〈n〉 ≤ 2) 2D perovskites in semitransparent photovoltaics (ST-PVs) has been hindered by their strong exciton binding energy and high electrical anisotropy. Here, the phase distribution is expanded fully and orderly to enable efficient charge transport in 2D (NMA)₂(MA)Pb₂I₇ (NMA: 1-naphthylmethylammonium, MA: CH₃NH₃⁺) perovskite films by regulating the sedimentation dynamics of organic cation-based colloids. Ammonium chloride is synergistically introduced to enhance the phase separation further and construct a favorable out-of-plane orientation. The wide and graded phase distribution well aligns the energy level to facilitate charge transfer. As a result, the first application of an average 〈n〉 = 2 2D perovskite is implemented in ST-PVs with visible power conversion efficiency (PCE) of 7.52% and high average visible transmittance (AVT) of 40.5%. This study offers a new candidate and an effective strategy for efficient and stable ST-PVs and is relevant to other perovskite optoelectronic devices.