Chemical Reduction of Iodine Impurities and Defects with Potassium Formate for Efficient and Stable Perovskite Solar Cells

The performance of perovskite solar cells (PSCs) is negatively affected by iodine (I₂) impurities generated from the oxidation of iodide ions in the perovskite precursor powder, solution, and perovskite films. In this study, the use of potassium formate (HCOOK) as a reductant to minimize the presence of detrimental I₂ impurities is presented. It is demonstrated that HCOOK can effectively reduce I₂ back to I⁻ in the precursor solution as well as in the devices under external conditions. Furthermore, the introduced formate anion (HCOO⁻) and alkali metal cation (K⁺) can reduce the defect density within the perovskite film by modulating perovskite growth and passivating electronic defects, significantly prolonging the carrier lifetime and reducing the J–V hysteresis. Consequently, the maximum efficiency of the HCOOK-doped planar n–i–p PSCs reaches 23.8%. After 1000 h of operation at maximum power point tracking under continuous 1 sun illumination, the corresponding encapsulated devices retain 94% of their initial efficiency.     

Efficient Cesium Lead Halide Perovskite Solar Cells through Alternative Thousand‐Layer Rapid Deposition

The novel growth of cesium lead halide perovskite thin films, which are prepared through thousand‐layer rapid alternative deposition, is performed by developing an active perovskite film consisting of a layer‐by‐layer structure. This method is considerably more difficult to be implemented from the solution process. The obtained thin film morphology and characteristics are distinguished from that of the traditional a few layers and two‐material codeposition. These alternative deposited perovskites are integrated with vacuum‐deposited carrier‐transporting layers and electrodes, and all vacuum‐sublimed perovskite solar cells exhibit an outstanding power conversion efficiency of 13.0%. The use of these devices for environmental light energy harvesting provides a power conversion efficiency of 33.9% under fluorescent light illumination of 1000 lux.     

Highly Efficient and Stable Wide-Bandgap Perovskite Solar Cells via Strain Management

Wide-bandgap (WBG) perovskite solar cells (PSCs) with high performance and stability are in considerable demand to boost tandem solar cell efficiencies. Perovskite bandgap broadening results in a high barrier for enhancing the efficiency of PSCs and phase segregation in perovskite. In this study, it is shown that the residual strain is the key factor affecting the WBG perovskite device efficiency and stability. The dimethyl sulfoxide addition helps lead halide with opening the layer spacing to form intermediate phases that provide more nucleation sites to eliminate lattice mismatch with organic components, which dominates the strain effects on the WBG perovskite growth in a sequential deposition. By minimizing the strain, 1.67 and 1.77 eV nip devices with record efficiencies of 22.28% and 20.45%, respectively, can be achieved. The greatly suppressed phase segregation enables the devices with retained 90–95% of initial efficiency over 4000 h of damp stability and 80–90% of initial efficiency over 700 h of maximum-power-point (MPP) stability. Besides, the 1.67 eV pin devices can achieve a competitive 22.3% efficiency with considerable damp-heat, pre-ultraviolet (pre-UV) aging and MPP tracking stability according to IEC 61215. The final efficiency of more than 28.3% for the perovskite/Si tandem is obtained.     

In Situ Growth of 2D Perovskite Capping Layer for Stable and Efficient Perovskite Solar Cells

2D halide perovskites have recently been recognized as a promising avenue in perovskite solar cells (PSCs) in terms of encouraging stability and defect passivation effect. However, the efficiency (less than 15%) of ultrastable 2D Ruddlesden–Popper PSCs still lag far behind their traditional 3D perovskite counterparts. Here, a rationally designed 2D‐3D perovskite stacking‐layered architecture by in situ growing 2D PEA₂PbI₄ capping layers on top of 3D perovskite film, which drastically improves the stability of PSCs without compromising their high performance, is reported. Such a 2D perovskite capping layer induces larger Fermi‐level splitting in the 2D‐3D perovskite film under light illumination, resulting in an enhanced open‐circuit voltage (V_oc) and thus a higher efficiency of 18.51% in the 2D‐3D PSCs. Time‐resolved photoluminescence decay measurements indicate the facilitated hole extraction in the 2D‐3D stacking‐layered perovskite films, which is ascribed to the optimized energy band alignment and reduced nonradiative recombination at the subgap states. Benefiting from the high moisture resistivity as well as suppressed ion migration of the 2D perovskite, the 2D‐3D PSCs show significantly improved long‐term stability, retaining nearly 90% of the initial power conversion efficiency after 1000 h exposure in the ambient conditions with a high relative humidity level of 60 ± 10%.     

Multifunctional Enhancement for Highly Stable and Efficient Perovskite Solar Cells

With a certified efficiency as high as 25.2%, perovskite has taken the crown as the highest efficiency thin film solar cell material. Unfortunately, serious instability issues must be resolved before perovskite solar cells (PSCs) are commercialized. Aided by theoretical calculation, an appropriate multifunctional molecule, 2,2-difluoropropanediamide (DFPDA), is selected to ameliorate all the instability issues. Specifically, the carbonyl groups in DFPDA form chemical bonds with Pb²⁺ and passivate under-coordinated Pb²⁺ defects. Consequently, the perovskite crystallization rate is reduced and high-quality films are produced with fewer defects. The amino groups not only bind with iodide to suppress ion migration but also increase the electron density on the carbonyl groups to further enhance their passivation effect. Furthermore, the fluorine groups in DFPDA form both an effective barrier on the perovskite to improve its moisture stability and a bridge between the perovskite and HTL for effective charge transport. In addition, they show an effective doping effect in the HTL to improve its carrier mobility. With the help of the combined effects of these groups in DFPDA, the PSCs with DFPDA additive achieve a champion efficiency of 22.21% and a substantially improved stability against moisture, heat, and light.     

Molecular Configuration Engineering in Hole-Transporting Materials toward Efficient and Stable Perovskite Solar Cells

The development of hole-transporting materials (HTMs) that can passivate defects in perovskite is of great significance in improving the efficiency and long-term stability of perovskite solar cells. To date, the investigation on HTMs mainly focus on exploring new structures, while molecular configuration is seldomly concerned. In this work, two small molecules are developed as HTMs with benzil and phenanthrene quinone as the core structure, respectively. With similar structure and the same defect passivation groups, whereas, the two molecules exhibit different configurations, thus distinct properties. Compared to 3,6-bis(3,6-bis(bis(4-methoxyphenyl)amino)-9H-carbazol-9-yl)phenanthrene-9,10-dione (PQ) with a rigid core structure, the benzil group in 1,2-bis(4-(3,6-bis(bis(4-methoxyphenyl)amino)-9H-carbazol-9-yl)phenyl)ethane-1,2-dione (DB) is flexible and can adjust molecular configuration to efficiently interact with the underlying perovskite material, which is confirmed from both experimental results and theoretical simulations. The DB-based device exhibits a high power conversion efficiency of 22.21% with excellent long-term stability, superior to the PQ-based device (20.22%). This study demonstrates that molecular configuration engineering will directly affect the properties of hole transport materials, as well as their interactions with perovskite, which should also be taken into consideration when devising HTMs.     

Multifunctional Cross-Linked Polyurethane Polymer as Interface Layer for Efficient and Stable Perovskite Solar Cells

In the past decade, perovskite solar cells (PSCs) have made remarkable progress in improving power conversion efficiency (PCE). In order to further improve the photovoltaic performance and long-term stability of PSCs, the interface layer is essential. A multifunctional cross-linked polyurethane (CLPU) is designed and synthesized via the spontaneous quaternization of polyurethane and 1, 6-diiodohexane on the surface of the perovskite layer. CLPU layer cannot only effectively induce secondary crystallization and passivate the surface defects of perovskite, reduce the non-radiative recombination, but also effectively block the moisture invasion. By this strategy, Cs_0.05FA_0.95PbI₃ PSCs with excellent reproducibility, is realized, achieving a PCE of 23.14% with an open-circuit voltage of 1.11 V, a short-circuit current density of 25.69 mA cm⁻², and a fill factor of 0.81. In addition, the unencapsulated devices show enhanced stability in 35 ± 5% relative humidity (RH) near 3000 h and in 65 ± 5% RH over 700 h. This study provides valuable insights into the role of CLPU interface layer in PSCs, which are essential for the design of high-performance devices.     

Bidirectional Targeted Therapy Enables Efficient,Stable, and Eco-Friendly Perovskite Solar Cells

Perovskite solar cells (PSCs) have witnessed rapid development toward commercialization based on their superior efficiency except for some remained misgivings about their poor stability primarily originating from interfacial problems. Robust back interface for neutralization of crystal defects, depression of dopant lithium ions (Li⁺) diffusion, and even inhibition of toxic lead (Pb) leakage is highly desirable; however, it remains a great challenge. Herein, a cost-effective interfacial therapy approach is developed to simultaneously alleviate the obstacles aforementioned. A small molecule, 1,4-dithiane with unique chair structure, is adapted to interact with under-coordinated Pb²⁺ on perovskite surface and Li⁺ from hole transport layer, neutralizing interfacial defects and suppressing Li⁺ diffusion. Besides, the presence of 1,4-dithiane can efficiently modulate interfacial energetics, enhance hydrophobicity of PSCs, and anchor Pb atoms via S Pb bond. Consequently, the target devices perform better than control devices when exposed to light-soaking, moisture, and thermal stress owing to the synergistic suppression of trap-state density, ions migration, and moisture permeation. The optimized target device delivers a champion efficiency of 23.27% with mitigated Pb leakage. This study demonstrates a promising functionalized modification strategy for constructing efficient, stable, and eco-friendly PSCs.     

Undoped Hole Transport Layer Toward Efficient and Stable Inorganic Perovskite Solar Cells

Numerous strategies have been practiced to improve the power conversion efficiency of CsPbI₂Br-based perovskite solar cells (PSCs), which definitely makes efficiency gradually approach the theoretical efficiency limit. However, sufficient device stability is still in urgent demand for commercialization, pushing to overcome some instability sources induced by hygroscopicity of spiro-OMeTAD and residual strain of perovskite layer. To address these issues, p-type semiconductor of PCPDTBT is used to replace spiro-OMeTAD, enabling dual functions of hole transport and strain regulation. On the one hand, undoped PCPDTBT performs excellent hole extraction and transport, while avoiding the perovskite degradation caused by the hygroscopicity of common additives. On the other hand, PCPDTBT assisted by a thermally spin-coating method compensates for the thermally-induced residual strain in perovskite layer owing to its high thermal expansion coefficient. Consequently, CsPbI₂Br-based PSCs with PCPDTBT layer achieve improved efficiency of 16.5% as well as enhanced stability. This study provides a simple and facile strategy to achieve efficient and stable CsPbI₂Br-based PSCs.     

Efficient Perovskite Hybrid Solar Cells via Ionomer Interfacial Engineering

The surface of the solution‐processed methylammonium lead tri‐iodide (CH₃NH₃PbI₃) perovskite layer in perovskite hybrid solar cells (pero‐HSCs) tends to become rough during operation, which inevitably leads to deterioration of the contact between the perovskite layer and the charge‐extraction layers. Moreover, the low electrical conductivity of the electron extraction layer (EEL) gives rises to low electron collection efficiency and severe charge carrier recombination, resulting in energy loss during the charge‐extraction and ‐transport processes, lowering the efficiency of pero‐HSCs. To circumvent these problems, we utilize a solution‐processed ultrathin layer of a ionomer, 4‐lithium styrenesulfonic acid/styrene copolymer (LiSPS), to re‐engineer the interface of CH₃NH₃PbI₃ in planar heterojunction (PHJ) pero‐HSCs. As a result, PHJ pero‐HSCs are achieved with an increased photocurrent density of 20.90 mA cm^?2, an enlarged fill factor of 77.80%, a corresponding enhanced power conversion efficiency of 13.83%, high reproducibility, and low photocurrent hysteresis. Further investigation into the optical and electrical properties and the thin‐film morphologies of CH₃NH₃PbI₃ with and without LiSPS, and the photophysics of the pero‐HSCs with and without LiSPS are shown. These demonstrate that the high performance of the pero‐HSCs incorporated with LiSPS can be attributed to the reduction in both the charge carrier recombination and leakage current, as well as more efficient charge carrier collection, filling of the perforations in CH₃NH₃PbI_3, and a higher electrical conductivity of the LiSPS thin layer. These results demonstrate that our method provides a simple way to boost the efficiency of pero‐HSCs.     

Efficient and Thermally Stable Wide Bandgap Perovskite Solar Cells by Dual-Source Vacuum Deposition

Wide bandgap perovskites are being widely studied in view of their potential applications in tandem devices and other semitransparent photovoltaics. Vacuum deposition of perovskite thin films is advantageous as it allows the fabrication of multilayer devices, fine control over thickness and purity, and it can be upscaled to meet production needs. However, the vacuum processing of multicomponent perovskites (typically used to achieve wide bandgaps) is not straightforward, because one needs to simultaneously control several thermal sources during the deposition. Here a simplified dual-source vacuum deposition method to obtain wide bandgap perovskite films is shown. The solar cells obtained with these materials have similar or even larger efficiency as those including multiple A-cations, but are much more thermally stable, up to 3500 h at 85 °C for a perovskite with a bandgap of 1.64 eV. With optimized thickness, record efficiency of >19% and semitransparent devices with stabilized power output in excess of 17% are achieved.     

A Regularity-Based Fullerene Interfacial Layer for Efficient and Stable Perovskite Solar Cells via Blade-Coating

The electron transport layer (ETL) plays a crucial part in extracting electron carriers while optimizing the interfacial contact of perovskite/electrode in planar heterojunction perovskite solar cells (PVSCs). Despite various ETLs being designed for efficient PVSCs, there exists hardly any research on the effect of molecular stacking order on device performance. Herein, poly(ethylene-co-vinyl acetate) (EVA) is employed as the [6,6]-phenyl-C₆₁-butyric acid methyl ester (PC₆₁BM) solution additive. The strong binding energy between EVA with PC₆₁BM promotes the molecular stacking order of ETLs, which alleviates the morphology inhomogeneity, possesses a matched energy level, blocks ion migration, and improves the water–oxygen barrier of perovskite devices. The blade-coated MAPbI₃-based PVSCs achieve a power conversion efficiency (PCE) of 19.32% with positive reproducibility and negligible hysteresis, as well as maintain 90% and 80% of the initial PCE after storage under inert and ambient conditions (52% humidity) for 1500 h without encapsulation. This strategy also improves the champion PCE of CsFAMA-based PVSCs to 20.33%. These findings demonstrate that the regulation of molecular stacking order is a valid approach to optimize interfacial charge-carrier recombination in PVSCs, which meet the demand for high-performance ETL in large-area PVSCs and improve the upscaling of the fabrication technology toward practical applications.     

Efficient and Stable Mesoscopic Perovskite Solar Cells Using PDTITT as a New Hole Transporting Layer

Stability is the main challenge in the field of organic–inorganic perovskite solar cells (PSCs). Finding low‐cost and stable hole transporting layer (HTL) is an effective strategy to address this issue. Here, a new donor polymer, poly(5,5‐didecyl‐5H‐1,8‐dithia‐as‐indacenone‐alt‐thieno[3,2‐b]thiophene) (PDTITT), is synthesized and employed as an HTL in PSCs, which has a suitable band alignment with respect to the double‐A cation perovskite film. Using PDTITT, the hole extraction in PSCs is greatly improved as compared to commonly used HTLs such as 2,2′,7,7′‐tetrakis[N,N‐di(4‐methoxyphenyl)amino]‐9,9′‐spirobifluorene (spiro‐OMeTAD), addressing the hysteresis issue. After careful optimization, an efficient PSC is achieved based on mesoscopic TiO₂ electron transporting layer with a maximum power conversion efficiency (PCE) of 18.42% based on PDTITT HTL, which is comparable with spiro‐OMeTAD‐based PSC (19.21%). Since spiro‐based PSCs suffer from stability issue, the operational stability in the PSC with PDTITT HTL is studied. It is found that the device with PDTITT retains 88% of its initial PCE value after 200 h under illumination, which is better than the spiro‐based PSC (54%).     

Surface Reconstruction Engineering with Synergistic Effect of Mixed-Salt Passivation Treatment toward Efficient and Stable Perovskite Solar Cells

Surface passivation treatment is a widely used strategy to resolve trap-mediated nonradiative recombination toward high-efficiency metal-halide perovskite photovoltaics. However, a lack of passivation with mixture treatment has been investigated, as well as an in-depth understanding of its passivation mechanism. Here, a systematic study on a mixed-salt passivation strategy of formamidinium bromide (FABr) coupled with different F-substituted alkyl lengths of ammonium iodide is demonstrated. It is obtained better device performance with decreasing chain length of the F-substituted alkyl ammonium iodide in the presence of FABr. Moreover, they unraveled a synergistic passivation mechanism of the mixed-salt treatment through surface reconstruction engineering, where FABr dominates the reformation of the perovskite surface via reacting with the excess PbI₂. Meanwhile, ammonium iodide passivates the perovskite grain boundaries both on the surface and top perovskite bulk through penetration. This synergistic passivation engineer results in a high-quality perovskite surface with fewer defects and suppressed ion migration, leading to a champion efficiency of 23.5% with mixed-salt treatment. In addition, the introduction of the moisture resisted F-substituted groups presents a more hydrophobic perovskite surface, thus enabling the decorated devices with excellent long-term stability under a high humid atmosphere as well as operational conditions.     

Incubating High-Quality Perovskite Film via Facial Mask Technique for Efficient and Stable Solar Cells

High-performance perovskite film with superior internal and surface qualities is critical for perovskite solar cells (PSCs) but hardly achievable due to the rapid crystallization rate of perovskite itself. Herein, a novel technique by in situ manipulating perovskite crystal growth and modifying the surface properties is developed using organic passivating agent-assisted polydimethylsiloxane membrane as a facial mask (FM) of perovskites. By placing the perovskite-precursor films with their faces toward the designed FM during thermal annealing, a favorable microenvironment is constructed for incubating high-quality perovskite films with smooth surface, enhanced vertical orientation of (100) plane, and well-adjusted interfacial energy levels. With this versatile FM incubation technique, efficient PSCs for both methylammonium (MA)-based and formamidinium (FA)-MA-Cs mixed perovskite systems are facilely fabricated, delivering excellent humidity/thermal stabilities and promising efficiencies up to 21.4% with an improved open-circuit voltage of 1.15 V in MA-based devices. This study not only provides a facile and efficient approach to rationally manage the perovskite growth process, but also reveals the fundamental characteristics of high-quality perovskite films comprehensively for the construction of efficient and stable PSCs.     

Efficient and Stable Inverted Perovskite Solar Cells with TOASiW12-Modified Al as a Cathode

Inexpensive metal Al is scarcely utilized as the cathode in the perovskite solar cells (PVSCs) because its violent reaction with perovskite active layer results in poor device stability in air. It is urgent to improve the efficiency and stability of PVSCs with Al as the cathode for mass production of low-cost PVSCs. Herein, a novel solution-processed cathode interlayer material, surfactant-encapsulated polyoxometalate complex [(C₈H₁₇)₄N]₄[SiW₁₂O₄₀] (TOASiW₁₂) is reported. Using TOASiW₁₂-modified Al as the cathode, the power conversion efficiency (PCE) of 20.64% has been achieved in the inverted PVSCs. The findings demonstrate that a thin TOASiW₁₂ layer can effectively obstruct the chemical reaction between Al and perovskite layer, and significantly enhance the device stability. The unencapsulated devices with TOASiW₁₂-modified Al retain more than 80% of the initial PCE after 350 h storage in the ambient atmosphere at 45% relative humidity. This study provides an excellent alternative cathode interlayer material for efficient and stable inverted PVSCs.     

Constructing All-Inorganic Perovskite/Fluoride Nanocomposites for Efficient and Ultra-Stable Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have rapidly developed over the past decade and have achieved the latest certified power conversion efficiency (PCE) up to 25.5%. However, unsatisfactory long-term operational stability for these hybrid PSCs remains a huge obstacle to further development and commercialization. Herein, a unique hetero-structured CsPbI₃/CaF₂ perovskite/fluoride nanocomposites (PFNCs) is fabricated via a newly developed facile two-step hetero-epitaxial growth strategy to deliver efficient and ultra-stable PSCs. After being incorporated into the crystal lattice of α-phase CsPbI₃ perovskite, the cubic-phase CaF₂ in the resultant CsPbI₃/CaF₂ PFNCs can not only passivate the intrinsic defects of CsPbI₃ perovskite itself but also effectively suppress the notorious ion migration in hybrid perovskite Cs_0.05FA_0.81MA_0.14PbI_2.55Br_0.45 (CsFAMA) thin-films of PSCs. As such, the CsFAMA PSC devices based on CsPbI₃/CaF₂-deposited perovskite thin-film achieve a mean PCE of 20.45%, in sharp contrast to 19.33% of the control devices without deposition. Specifically, the CsPbI₃/CaF₂-deposited PSC retains 85% of its original PCE after 1000 h continuous operation at the maximum power point under AM 1.5G solar light, far better than those of the control and CsPbI₃-deposited PSCs with a device T₈₅ lifetime of 315 and 125 h, respectively.     

Interface Energy-Level Management toward Efficient Tin Perovskite Solar Cells with Hole-Transport-Layer-Free Structure

Lead-free tin perovskite solar cells (PSCs) have emerged as a promising candidate toward high-performance and eco-friendly photovoltaic technology with great potential for future application. However, tin PSCs with over 10% efficiency usually feature an organic hole transport layer (HTL) at the illumination side that may induce device degradation during long-term operation. Removing the unstable organic HTL is an important way to solve these stability issues, but the efficiency of HTL-free tin PSCs is still much lower than that of the completed cells. Herein, it is demonstrated that formamidinium tin iodide doped with heterogeneous ammonium salts can form an upward band-bending structure to selectively extract the hole in the HTL-free devices. By using this band-bending structure, a promising efficiency of over 10% is first achieved for the lead-free PSCs with a HTL-free structure. More importantly, the optimized cell is highly stable, keeping 95% and 90% of the initial efficiency after continuous light soaking for 40 days and 80 °C annealing for 300 h, respectively. This work paves a route toward the development of efficient, eco-friendly, and highly stable perovskite photovoltaics.     

Metal Oxide Charge Transport Layers for Efficient and Stable Perovskite Solar Cells

Currently, the efficiency of perovskite solar cells (PSCs) is ≈24%. For the fabrication of such high efficiency PSCs, it is necessary to use both electron and hole transport layers to effectively separate the charges generated by light absorption of the perovskite layer and selectively transfer the separated electrons and holes. In addition to the efficiency, the materials used for transporting charges must be resilient to light, heat, and moisture to ensure long‐term stability of PSCs; furthermore, low‐cost fabrication is required to form a charge transport layer at low temperatures by a solution process. For this purpose, metal oxides are best suited as charge transport materials for PSCs because of their advantages such as low cost, long‐term stability, and high efficiency. In this Review, the metal oxide electron and hole transport materials used in PSCs are reviewed and preparation of these materials is summarized. Finally, the challenges and future research direction for metal oxide‐based charge transport materials are described.