Effect of dehydrochlorination of PVC on miscibility and phase separation of binary and ternary blends of poly(vinyl chloride), poly(ethylene-co-vinyl acetate) and poly(styrene-co-acrylonitrile)

The enhancement of miscibility at the lower critical solution temperature (LCST) of the blends poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) (PVC/EVA), poly(vinyl chloride)/poly(styrene-co-acrylonitrile) (PVC/SAN) and poly(vinyl chloride)/poly(ethylene-co-vinyl acetate)/poly(styrene-co-acrylonitrile) (PVC/EVA/SAN) was observed at the micron level. Such miscibility is attributed to the dehydrochlorination and formation of hydrogen bonds between blend components. However, macrolevel immiscibility of these blends heated to the LCST was observed. Such microdomain compatibility of these blends gives a synergistic character. Brittle-type failure observed for LCST samples testifies to the synergism in treated blends. ©1997 SCI     

Fourier transform infrared spectroscopic studies of the poly(styrene-co-acrylonitrile) and poly (vinyl chloride-co-vinyl acetate) blends

The Fourier transform infrared (FTIR) spectroscopic studies of the poly-(styrene-co-acrylonitrile) (SAN) and poly(vinyl chloride-co-vinyl acetate) (VYHH) blends produced by different blending techniques, viz., solution blending, melt-blending, and also the co-precipitation methods of blending, were performed. In the case of miscible blend systems, substantial band shiftings took place, whereas immiscible blend systems showed slight or no band shifting. The miscible blends showed a substantial residual spectrum which was absent in the case of the immiscible system when a similar subtraction process was carried out. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 991–1000, 1997     

Miscibility studies of polymer blends by viscometry methods

The intrinsic viscosities of blends of poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) (PVC/EVA), poly(vinyl chloride)/poly(styrene-co-acrylonitrile) (PVC/SAN), and poly(ethylene-co-vinyl acetate)/poly(styrene-co-acrylonitrile) (EVA/SAN) have been studied in cyclohexanone as a function of blend composition. In order to predict the compatibility of polymer pairs in solution, the interaction parameter term, Δb, obtained from the modified Krigbaum and Wall theory, and the difference in the intrinsic viscosities of the polymer mixtures and the weight average intrinsic viscosities of the two polymer solutions taken separately are used. © 1994 John Wiley & Sons, Inc.     

Analysis of holding power in the blends of poly(butyl acrylate) with poly(vinylidene fluoride-cohexafluoro acetone)

Shear adhesion of pressure-sensitive adhesive tapes was evaluated for the blends of poly(butyl acrylate) with poly(vinylidene fluoride-co-hexafluoro acetone). The shear adhesion was determined as the function of the shear strain of pressure-sensitive adhesive tape against elapsed time under the shear stress. Shear adhesion of the blends increased with increasing poly(vinylidene fluoride-co-hexafluoro acetone) content. Experimental shear strain data were characterized with dynamic viscosity, stress and shear rate plot, and a generalized viscoelastic model of shear adhesion. However, the experimental data cannot be expressed with these viscoelastic properties. It is believed that shear adhesion is influenced by the viscoelastic properties and other factors (e.g., friction coefficient between adhesive and adherend or cohesive strength of adhesive polymer). © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68:727–738, 1998     

Miscibility and mechanical properties of poly(styrene-co-4-vinylpyridine) and poly(butyl acrylate-co-acrylic acid) ionomer blends

The miscibility of polystyrene with poly(butyl acrylate) is very poor. Ionic interactions have been utilized recently as miscibility enhancers. In this paper, dynamic mechanical studies indicate that ion pair–ion pair interactions can be utilized to achieve miscibility in blends of polystyrene and poly(butyl acrylate). The styrenes contain 0–15mol% quaternary ammonium salt of 4-vinylpyridine, while the butyl acrylates contain 0–15mol% potassium acrylate groups. The miscibility increases with increase of ion content. When the ion content exceeds 11mol%, the polymers can be completely miscible. The mechanical properties of the ionomers and their blends were also studied. The results indicate that the tensile strength of ionomer blends is higher than that of corresponding poly(butyl acrylate-co-potassium acrylate)s (PBA-AA-K). The elongation at break of ionomer blends is higher than that of the corresponding poly(styrene-co-N-methyl-4-vinylpyridinium iodide) (PS-4VP-Q). © 1998 SCI.     

Surface quantitative characterization of poly(styrene-co-4-vinyl phenol)/poly(styrene-co-4-vinyl pyridine) blends with controlled hydrogen bonding interactions

Time-of-flight secondary ion mass spectrometry (ToF-SIMS) was used to quantitatively correlate to the surface chemical composition determined from XPS in poly(styrene-co-4-vinyl phenol) (STVPh)/poly(styrene-co-4-vinyl pyridine) (STVPy) blends or complexes when the hydroxyl contents in STVPh copolymers were gradually increased. It was found that different mixing thermodynamics such as immiscibility, miscibility and complexation has little effect on the quantitative analysis of surface concentrations in the blends or complexes using ToF-SIMS. In the positive spectra, the normalized intensities or relative peak intensities can both be used to quantitatively analyze the surface vinyl phenol (VPh), styrene and vinyl pyridine (VPy) concentrations when peaks at m/z=119, 120 are used for VPh, peaks at m/z=103, 105, 115 for styrene and peaks at m/z=80, 93, 106 for VPy monomer units. In the negative spectra, the normalized intensities of peaks characteristic of VPh monomer units (m/z=16, 17, 93) seems to be not affected by hydrogen bonding formation and can be used in quantitative analysis.     

Processability enhancement of poly(lactic acid-co-ethylene terephthalate) by blending with poly(ethylene-co-vinyl acetate), poly(3-hydroxybutyrate-co-3-hydroxyvalerate), and poly(butylene succinate)

Processability enhancement feasibility of an in-house synthesized poly(lactic acid-co-ethylene terephthalate), PLET, is investigated by blending with commercial poly(ethylene-co-vinyl acetate), EVA, poly(3-hydroxybutyrate-co-3-hydroxyvalerate), PHBV, and poly(butylene succinate), PBS. The three blend systems are prepared by varying PLET contents, and their properties are characterized. DSC, SEM, and FTIR results indicate that PLET/EVA blends are immiscible, while the corresponding PLET/PBS and PLET/PHBV blends are miscible and partially miscible, respectively. DMA results show that the three blend systems have storage modulus comparable to those of commercial EVA, PHBV, and PBS, when PLET content is kept lower than 50, 25, and 25 wt%, respectively. PLET/EVA blends show higher thermal stability, compared to those of the other two blend systems. Results on degradability tests indicate that PLET/PBS blends show highest hydrolytic degradability, compared to the other two blends, as both blend constituents are associated in the hydrolytic degradation.     

Blends of poly(2,6-dimethyl-1,4-phenylene oxide)/ poly(styrene-co-methacrylic acid)/ poly(ethyl methacrylate-co-4-vinylpyridine)

Summary The miscibility of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) with poly(styrene-co-acrylic acid) (SAA) or poly(styrene-co-methacrylic acid) (SMA) containing respectively up to 22 mol % of acrylic or methacrylic acid was studied by Differential Scanning Calorimetry and viscosimetry. All PPO/SAA or PPO/SMA blends containing 60% or less by weight of PPO were miscible and showed only one glass transition temperature (Tg). Above 60% of PPO, two Tg's were however observed for the blends in which the acid content in the SAA or SMA reaches 20% or 12% by mole respectively; the higher Tg is slightly lower than the one of pure PPO, while the lower one corresponds to a miscible blend of lower content of PPO.A DSC study showed that depending on the blend ratio, two or three glass transition temperatures were observed when a copolymer of ethyl methacrylate containing 8 mol % of 4-vinylpyridine (EM4VP-8) was added to miscible PPO/SMA-12 blends. The PPO dissolution in the SMA-12 copolymer was affected by the specific interactions that occurred between this latter copolymer and the EM4VP-8.     

Compatibility behavior in thermoplastic polymer blends containing poly(t-butylstyrene-co-acrylonitrile)

The phase behavior of a series of binary component polymer blends of poly(ε-caprolactone) (PCL) and poly(t-butylstyrene-co-acrylonitrile) (TBSAN) containing varying contents of acrylonitrile (AN) was examined to determine the influence of copolymer composition and PCL content on blend miscibility or immiscibility. Thermal measurements were extensively used to determine phase behavior, i.e., a single compositionally dependent glass transition temperature implies blend miscibility. Otherwise, immiscibility is assumed to dominant blend behavior. It was determined that TBSAN and PCL form miscible blends over a broad range of AN content, i.e., spanning from below 43.2 mol % (19.8 wt %) to about 66.4 mol % (39.6 wt %), a range considerably different from that found in poly(styrene-co-acrylonitrile) copolymers. TBSAN-containing blends were found to be immiscible when the AN content is less than about 43 mol % or greater than about 67 mol %. Small-angle light-scattering and polarized light microscopy was used to probe the substantial morphological changes in the miscible blends. Little change was observed in the immiscible blends. These results clarify the phase separation observed in these blend systems. © 1993 John Wiley & Sons, Inc.     

The effect of ionic cross-links on the deformation behavior of homoblends made of poly(styrene-co-styrenesulfonic acid) and poly(styrene-co-4-vinylpyridine)

Deformation behavior of stoichiometric blends made from poly(styrene-co-styrenesulfonic acid) (SPS) and poly(styrene-co-4-vinylpyridine) (SVP) was investigated by TEM observation of strained thin films. An FTIR investigation revealed that ionic cross-links were formed between the component polymers upon blending due to intermolecular ion-ion interactions, which arose from proton transfer from sulfonic acid groups to pyridine groups. TEM observations indicate that the deformation mode of the blends changed from crazing only to crazing plus shear deformation, with the shear contribution becoming larger, as the ion content in the blends increased. Such changes in deformation mode can be understood as arising from an increase in the ‘effective’ strand density due to the formation of ionic cross-links upon blending. It was also found that the ionic cross-links via pyridinium cation/sulfonate anion ion pairs were more effective in inducing the transition of deformation mode than ionic cross-links via -SO₃⁻/Na⁺ or -SO₃⁻/Ca²⁺ ion pairs.     

Rheological behavior of blends of poly(methyl methacrylate) (PMMA) and poly(acrylonitrile-stat-styrene)-graft-polybutadiene (ABS)

The rheological behavior of blends of poly(methyl methacrylate) (PMMA) and poly(acrylonitrile-stat-styrene)-graft-polybutadiene (ABS) was investigated using a cone-and-plate rheometer. The rheological properties measured were shear stress (σ₁₂), viscosity (η), and first normal stress difference (N₁) as functions of shear rate (\documentclass{article}\pagestyle{empty}\begin{document}$ \dot \gamma$ \end{document}) in steady shearing flow, and storage modulus (G′) and loss modulus (G″) as functions of frequency (ω) in oscillatory shearing flow. It has been found that the rheological behavior of blends of ABS and PMMA was very similar to that of blends of poly(styrene-stat-acrylonitrile) (SAN) and PMMA, in that N₁ in logarithmic plots of N₁ versus σ₁₂, and G′ in logarithmic plots of G′ versus G″, vary regularly with blend composition. This has led us to conclude that the rubber particles that are grafted on an SAN resinous matrix in ABS resin plays only a minor role in influencing the compatibility of ABS/PMMA blends, and that the SAN chains attached to the surface of rubber particles, and the SAN matrix phase, play a major role in compatibilizing ABS resin with PMMA.     

Rheological behavior of compatible polymer blends. I. Blends of poly(styrene-Co-acrylonitrile) and poly(ε-caprolactone)

The rheological behavior of blends of poly(styrene-co-acrylonitrile) (SAN) and poly(ε-caprolactone) (PCL) was investigated, using a cone-and-plate rheometer. For the study, blends of various compositions were prepared by melt blending using a twin-screw compounding machine. The rheological properties measured were shear stress (σ₁₂), viscosity (η), and first normal stress difference (N₁) as functions of shear rate (γ) in steady shearing flow, and dynamic storage modulus (G′) and loss modulus (G″) as functions of angular frequency (ω) in oscillatory shearing flow, at various temperatures. It has been found that logarithmic plots of N₁ versus σ₁₂, and logarithmic plots of G′ versus G″, become virtually independent of temperature but vary regularly with blend composition, and that the zero-shear viscosity of the blends, (η_o)_blend, follows the relationship, 1/log(η_o)_blend = w_A/log η_0A + w_B/log η_0B, where η_0A and η_0B are the zero-shear viscosities of components A and B, respectively, and w_A and w_B are the weight fractions of components A and B, respectively. The physical implications of the relationship found are discussed.     

Morphology and deformation behavior of polymer blends made of poly(styrene-co-styrenesulfonic acid) and poly(methyl methacrylate-co-4-vinylpyridine)

The effect of a small amount of ionic groups (interactions) on the morphology and deformation behavior of stoichiometric blends made of poly(styrene-co-styrenesulfonic acid) (SPS) and poly(methyl methacrylate-co-4-vinylpyridine) (MVP) was investigated by Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). FTIR data revealed that intermolecular ion-ion interactions were formed between SPS and MVP polymers, arising from proton transfer from sulfonic acid groups to pyridine groups upon blending. TEM observations show that the morphology of the blends changes from macroscopic phase separation to microscopic phase separation, and to miscibility, with increasing ion content of the blends from 0 to 6 mol%. Correspondingly, deformation behavior of the blends changes from crazing only, to curved and branched crazing, and to crazing plus shear deformation. Such changes in deformation mode can be understood as arising from the morphological changes and the increase of ‘effective’ strand density due to the formation of ionic cross-links in the blends.     

Reactive melt blends of nylon with poly(styrene-co-maleic anhydride)

Melt blends of nylon with poly(styrene-co-maleic anhydride) (SMA) were prepared in a twin-screw extruder. Viscoelastic properties of the melt and morphological, thermal, and mechanical properties of the blends were determined. Fourier-transform infrared (FTIR) spectroscopy measurement indicated reactions between nylon and SMA. Melting peak temperature (T_m) of nylon was not changed in blends. This, together with the FTIR results, assured that the reactions occur mainly with the free amide end groups of nylon. Melt viscosity, elasticity, and the heat-distortion temperature (HDT) of nylon was significantly increased with the addition of SMA. Tensile strength and impact strength of nylon were, respectively, in general, increased and decreased with SMA.     

Studies on miscibility of blends of poly(ethylene-co-methyl acrylate) and poly(dimethyl siloxane) rubber by melt rheology

Rheological studies of the blends of poly(ethylene-co-methyl acrylate) (EMA) and poly(dimethyl siloxane) (PDMS) rubber have been carried out at various temperatures and different shear rates by a Monsanto processability tester. The melt viscosities of the blends are found to be higher than that calculated as per the additivity rule, showing a positive deviation, an indication of synergism present in the blends during melt processing. This confirms our earlier finding that the blends are miscible throughout the composition range. The activation energy of flow of the blends are always higher than that calculated as per the additivity rule. The comparatively higher activation energy for the 30 : 70 EMA–PDMS rubber blend among the systems studied confirms our earlier finding that extent of reaction between EMA and PDMS rubber is significantly higher at this proportion of the blends studied. This substantiates the miscibility between blends of EMA and PDMS rubber throughout the composition range. © 1995 John Wiley & Sons, Inc.     

Effect of hydroxyl content on the morphology and properties of epoxy/poly(styrene-co-allylalcohol) blends

Blends based on epoxy resin and random copolymers, poly(styrene-co-allylalcohol) (PS-co-PA), were studied. Two PS-co-PA copolymers, with different hydroxyl content, and a polyallylalcohol (PA) homopolymer were used to analyze the effect of polyalcohol content. The polymers presented similar values of molar mass. The miscibility of noncured mixtures and the thermal transition behavior of cured blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). Its morphology was studied using both scanning and transmission electron microscopy (SEM and TEM). While the epoxy/PA blends are homogenous materials, because of the epoxy/hydroxyl reaction, PS-co-PA/epoxy blends shows separated phases. In these blends, the presence of a third glass transition, whose value is an intermediate between those of pure components, and the presence of a well-defined interfacial layer between PS-co-PA domains and epoxy matrix indicates a secondary epoxy/hydroxyl reaction. The modification of epoxy resin with PS-co-PA provides significant increase in the storage modulus measured by DMTA. POLYM. ENG. SCI., 47:1580–1588, 2007. © 2007 Society of Plastics Engineers     

Effects of poly(vinyl acetate) and poly(vinyl chloride‐co‐vinyl acetate) low‐profile additives on properties of cured unsaturated polyester resins. II. glass‐transition temperatures and mechanical properties

Three series of self‐synthesized poly(vinyl acetate)‐based low‐profile additives (LPAs), including poly(vinyl acetate), poly(vinyl chloride‐co‐vinyl acetate), and poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride), with different chemical structures and molecular weights were studied. Their effects on the glass‐transition temperatures and mechanical properties for thermoset polymer blends made from styrene, unsaturated polyester, and LPAs were investigated by an integrated approach of the static phase characteristics, cured sample morphology, reaction kinetics, and property measurements. Based on Takayanagi mechanical models, the factors that control the glass‐transition temperature in each phase region of the cured samples and the mechanical properties are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3347–3357, 2003     

Novel blends of alternating propene-carbon monoxide copolymers and styrenic copolymers

Summary Alternating propene-carbon monoxide copolymers (P-CO) were melt-blended with polystyrene, poly(styrene-co-acrylonitrile) (SAN), and with poly(styrene-co-maleic anhydride) (SMA). P-CO forms homogeneously miscible blends with SAN containing 25 wt% AN at the investigated blend compositions. The transparent blends have single, intermediate glass transition temperatures that fit the Fox equation. The elastic properties of P-CO at room temperature disappear upon blending with SAN because the T _g is driven above RT. Polystyrene and SMA are not miscible with P-CO and form heterogeneous blends with two glass transitions. This demonstrates that both the polarity of the styrenic copolymer and the nature of the comonomer govern its phase behavior. Received: 14 January 1999/Revised version: 19 April 1999/Accepted: 19 April 1999     

Studies on semiinterpenetrating polymer networks based on poly(vinyl chloride-co-vinyl acetate) and poly(alkyl methacrylates)

A number of semi-interpenetrating polymer networks (IPNs) based on linear poly(vinyl chloride-co-vinyl acetate) and poly(alkyl methacrylates) were synthesized. The semi-IPNs were found to be transparent, high strength materials. The IPNs show only one glass-transition temperature and it is dependent on the composition as studied by differential scanning calorimetry and dynamic mechanical analysis. These IPNs are also characterized by high tan δ values. The tensile strength of the IPNs were found to be higher compared to the starting polymers. In order to compare the properties of these IPNs with the corresponding homopolymers and blends, the latter were synthesized and the properties were studied. © 1994 John Wiley & Sons, Inc.     

Studies on polymer blends with moderate specific interactions. 2. phase structure of blends SAN/TPU and SAN/TPU/EVA

This paper deals with morphological studies of binary and ternary blends composed of poly(styrene-co-acrylonitrile) (SAN), polyurethane elastomer (TPU) and poly(ethylene-co-vinyl acetate) (EVA). Selective etching was found necessary to expose the morphologies of the blends. Chloroform or hot acetone, hexane/toluene (2/1v/v) and NaOH/CH₃OH (1wt%) were found to be selective etching agents for SAN, EVA and TPU, respectively. SAN and TPU form blends with fine dispersion structure, while SAN and EVA lead to rough phase structure with poor phase adhesion. These results are in accordance with the difference in the mechanical properties of SAN/TPU and SAN/EVA. In addition, for SAN/TPU/EVA blends, if TPU is only a minor component, it is preferentially located at the interphase, playing the role of a compatibilizer. As the amount of TPU increases, the compatibility is gradually improved. ©1997 SCI