Effect of PE-g-MA-Compatibilizer on the Morphology and Mechanical Properties of 70/30 HDPE/ENR Blends

The effects of PE-g-MA as a compatibilizer in binary blends of 70/30 high-density polyethylene/epoxidized natural rubber (HDPE/ENR) have been investigated by means of mechanical analysis and scanning electron microscopy. The special emphasis was given to the role of PE-g-MA in inducing interactions between HDPE and ENR. It has been observed that increasing the amount of PE-g-MA in the blend increases the tensile strength, elongation at break, and impact strength. It is believed that the degree of cross-link increased, which led to improve the interaction between the HDPE and ENR. The optimum stress values are shown in the blend containing 6% PE-g-MA. Scanning electron micrographs (SEM) of the samples also indicated that the addition of compatibilizer decreases the domain size of the dispersed phase. Well-dispersed plastic particles in a rubber matrix were strongly indicated in these samples. The results obtained reveal that the addition of PE-g-MA in HDPE/ENR blend led to an increase in the homogeneity of the blends.     

Core/shell morphologies in recycled poly(ethylene terephthalate)/linear low-density polyethylene/poly(styrene-<Emphasis Type="Italic">b</Emphasis>-(ethylene-<Emphasis Type="Italic">co</Emphasis>-butylene)-<Emphasis Type="Italic">b</Emphasis>-styrene) ternary blends

Compatibilizer plays very important roles in preparing high performance polymer composites, not only for the ternary immiscible polymer blends, but also for the recycled and reused of waste plastics mixture. Generally, the compatibilizers can be used as the toughening agent in blending polymer materials. In the present work, the poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) or maleic anhydride-grafted poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS-g-MA) acts as the compatibilizer and toughening agent for the preparation of R-PET/LDPE/SEBS (70/20/10) ternary blends. It must be pointed that the ternary blends are costlessly and conveniently prepared from the recycled poly(ethylene terephthalate) (R-PET) and linear low density polyethylene (LLDPE) through a melt blending in a co-rotating twin-screw extruder and injection moulded. The morphologies of the ternary blends are characterized by scanning electron microscopy (SEM). It was found that the blends contains reactive or non-reactive compatibilizer, the morphology originates from the LLDPE particles encapsulated by both SEBS and SEBS-g-MA. So, it results to the reduced interfacial tension between of the R-PET and SEBS-g-MA, in which the grafted chains of PET-g-SEBS-g-MA formed through in situ reaction between R-PET and SEBS-g-MA phases. Therefore, core–shell particles with smaller diameter disperse uniformly in the blends. Moreover, the good compatibilization and corresponding morphologies induce in balanced mechanical and thermal properties. DSC analysis show the dispersed phase particles could act as nucleating agent in the R-PET matrix, which results the improvement of the crystallization temperature. And it was also observed the decreased nucleation activity in graft copolymers in the R-PET/LLDPE/SEBS-g-MA blends. Notched Charpy impact strength and elongation at break are improved by the addition of compatibilizer.     

Effect of Thermoplastic Elastomer on Melt Rheological and Fracture Behavior of Poly(Lactic Acid)

Poly(lactic acid) (PLA) was melt blended with thermoplastic elastomer, maleic anhydride grafted poly[styrene-b-(ethylene-co-butylene)-b-styrene] (SEBS-g-MA) copolymer with varied concentration (10–40?wt%) using twin screw extruder. Dynamic rheological behavior of PLA/SEBS-g-MA blends investigated a transition from liquid-like behavior to solid-like behavior in the composition range of 10–20?wt% of SEBS-g-MA. The capillary rheometer analysis showed enhanced shear viscosity with increase in SEBS-g-MA content. At 10?wt% of SEBS-g-MA, a maximum in the non-essential work of fracture was observed which reflects resistance to crack propagation. Scanning electron microscopy revealed a transition in deformation mechanisms from voids, to fibrillation and cavitation.     

Morphology and Mechanical Properties of iPP/Silica Composites Modified with (Styrene-b-ethylene-co-butylene-b-styrene) Grafted with Maleic Anhydride

The effects of different silica grades and elastomer content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with added 5, 10, 15, and 20% of poly(styrene-b-ethylene-co-butylene-b-styrene) grafted with maleic anhydride (SEBS-g-MA) were investigated. The iPP/silica/SEBS-g-MA composites were designed by adding four silica fillers differing in size (nano- vs. micro-) and in surface properties (hydrophilic vs. hydrophobic) and SEBS-g-MA that was used as a proven effective impact modifier and compatibilizer simultaneously. The morphology of every composite was a spectrum of several morphologies rather than one exclusive morphology. Good concordance between observed and predicted morphology indicated that the morphology of a particular composite was controlled primarily by interfacial properties. Tensile and impact properties were influenced primarily by competitive effects of a stiff filler and tough SEBS-g-MA elastomer. Increased impact strength and strain at break caused by adding SEBS-g-MA indicated a significant overcoming of the elastomeric toughening effect in relation to the filler’s stiffening effect.     

Effect of compatibilizer on the crystallization,rheological, and tensile properties of LDPE/EVOH blends

The effect of the compatibilizer on the crystallization, rheological, and tensile properties of low-density polyethylene (LDPE)/ethylene vinyl alcohol (EVOH) (70/30) blends was investigated. Maleic anhydride-grafted linear low-density polyethylene (LLD-g-MAH) was used as the compatibilizer in various concentrations (from 1 to 12 phr). The interesting effect of compatibilization on the crystallization kinetics of the blends was noted, and the correlation between the morphology and the rheological and tensile properties was also discussed. Morphological analysis showed that the blends exhibited a regular and finer dispersion of the EVOH phase when LLD-g-MAH was added. Nonisothermal crystallization exotherms of the compatibilized LDPE/EVOH blends showed the retarded crystallization of the dispersed EVOH phase, which probably resulted from the constraint effect of the grafted EVOH (EVOH-g-LLD) as well as the size reduction of the EVOH domains. The blends exhibited increased melt viscosity and storage modulus and also enhanced tensile properties with the addition of LLD-g-MAH, which seemed to be attributable to both dispersed particle-size reduction and improved interfacial adhesion. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1245–1256, 1998     

A probe into the status quo of interfacial adhesion in the compatibilized ternary blends with core/shell droplets: Selective versus dictated compatibilization

A simple approach was applied to probe into the situation of interfacial adhesion in the compatibilized ternary polymer blends with core/shell morphology. The performance of compatibilization was discussed in terms of thermal, rheological, and mechanical properties analyses for blends prepared through different mixing strategies for which maleic anhydride‐grafted high‐density polyethylene (HDPE‐g‐MAH) could be localized at the interface of HDPE/poly(ethylene‐co‐vinyl alcohol) copolymer (EVOH) or HDPE/polyamide 6 (PA‐6) in their ternary blends. Two mixing strategies, one simultaneously (one‐step or selective) and two sequentially (two‐step or dictated), were performed, compared, and discussed. It was found that mixing policy (dictated or selective) significantly changes the interfacial adhesion, as signaled by variations in rheological and thermal properties. In the case of mechanical properties, facilitation of stress transfer across the matrix/shell/core interfaces was detected by calculation of semi‐experimental models' coefficients. It was found that one‐step mixing or selective localization of HDPE‐g‐MAH helps in accumulation of more compatibilizer molecules at the interface HDPE/EVOH or EVOH/PA‐6. By contrast, addition of compatibilizer to minor phase (masterbatch of EVOH and PA‐6) or to HDPE matrix alone in case of two‐step blending causes imperfect stress transfer. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45503.     

Effect of extruder type on the properties and morphology of reactive blends based on polyamides

The morphology and mechanical properties of polyamide-based blends prepared in single and corotating twin-screw extruders were compared using transmission electron microscopy (TEM) techniques. Reactive polyamide blends with SEBS-g-MA (a maleated styrenic triblock copolymer with ethylene–butvlene midblocks), EPR-g-MA (a maleated ethylene/propylene rubber), and ABS were selected for the purpose of this investigation. For blends of SEBS-g-MA with difunctional (nylon x,y) polyamides (e.g., nylon 6,6; nylon 12,12), the twin-screw extruder was more effective in producing a finer dispersion of the rubber phase, which resulted in a significant lowering of the ductile–brittle transition temperature in case of the nylon 6,6 blend. On the other hand, blends of SEBS-g-MA with the mono-functional nylon 6 material led to rubber particles that were too small for toughening for both extruder types employed in this work. For nylon 6/EPR-g-MA blends, the single-screw extruder led to blends with excellent low-temperature impact properties for both single-step and masterbatch mixing techniques, whereas nylon 6/EPR-g-MA blends prepared in a single-step operation in the twin-screw extruder were brittle under ambient conditions. For difunctional polyamide blends with ABS (compatibilized with an imidized acrylic polymer), the morphology and mechanical properties were found to be independent of the extruder type employed for processing. © 1994 John Wiley & Sons, Inc.     

Enhanced impact strength of compatibilized poly(lactic acid)/polyamide 11 blends by a crosslinking agent

Maleated poly(lactic acid) (PLA-g-MA) was prepared through melt grafting of maleic anhydride onto a PLA backbone with the aid of a radical initiator. PLA-g-MA thus formed was incorporated into PLA/polyamide 11 (PA11) blends as a reactive compatibilizer. By morphological observation, it was assessed that PLA-g-MA lowered the interfacial energy and strengthened the interface between PLA and PA11. However, the compatibilized PLA/PA11 blends did not show significant improvement of impact strength compared with noncompatibilized PLA/PA11 blends. Measurements of the molecular weight and impact strength of PLAs compounded with various amounts of radical initiators revealed that decreased molecular weight of PLA by the radical initiator used for the preparation of PLA-g-MA is responsible for this unexpected result. To compensate the decrease of the molecular weight, a crosslinking agent was incorporated in the preparation step of PLA-g-MA. It was found that the crosslinking agent is effective in preventing the molecular weight reduction. As a result, the impact strength of the PLA/PA11 blend was enhanced to a great extent by the PLA-g-MA prepared with the crosslinking agent.     

Influence of morphology on rheological and mechanical properties of SEBS-toughened,glass-bead-filled isotactic polypropene

The influence of morphology of glass-bead-filled isotactic polypropene containing 0–20 vol% thermoplastic elastomers (TPE) on mechanical and rheological properties was investigated. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene(SEBS) and the corresponding block copolymer grafted with maleic anhydrid (SEBS-g-MA) were used as thermoplastic elastomers, realizing, in the first case, a three-phase morphology with separately dispersed glass beads and SEBS particles. In the second case, SEBS-g-MA forms an elastomeric interlayer between glass beads and polypropene matrix, comprising core–shell particles. Young's modulus and tensile yield stress of the hybrid composites decrease with an increase in TPE volume fraction due to low stiffness and strength of TPE. In comparison with the three-phase morphology of hybrid composites with SEBS, SEBS-g-MA interlayers effect a reduced stiffness of the hybrid composites but improve interfacial adhesion and, thus, tensile yield stress. Rheological storage and loss moduli increase with an increase in glass bead and TPE volume fraction. Due to improved interfacial adhesion, melt elasticity and viscosity are enhanced by the SEBS-g-MA interlayer when compared with separately dispersed SEBS. Consequently, the reduced stiffening effect of the glass beads due to SEBS-g-MA interlayer decreases mechanical elasticity, whereas improved interfacial adhesion, also promoted by the SEBS-g-MA interlayer, enhances tensile yield stress and melt elasticity. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2499–2506, 1998     

Comparative study of different maleic anhydride grafted compatibilizer precursors towards LDPE/PA6 blends: Morphology and mechanical properties

The study deals with the effectiveness of maleic anhydride grafted styrene-b-ethylene-co-propylene copolymer (SEPMA) as compatibilizer precursor (CP) for blends of low density polyethylene (LDPE) with polyamide-6 (PA). The CP was produced by grafting MA onto SEP in the melt. The specific interactions between the CP and the blends components have been investigated through characterizations of the binary LDPE/CP and PA/CP blends. The compatibilizing efficiency of the MA-grafted SEP, as revealed by the thermal properties and the morphology of the compatibilized blends, has been shown to be excellent. The morphology, as well as the mechanical properties of the compatibilized with SEPMA 75/25 w/w and 25/75 w/w LDPE/PA6 blends have been compared with those of the blends compatibilized with maleic anhydride functionalized HDPE sample (1-HDPE-g-MA) and with a commercial maleic anhydride grafted styrene-b-(ethylene-co-1-butene)-b-styrene copolymer (SEBSMA1). The results show that the strong compatibilizing efficiency of SEPMA is comparable with that of SEBSMA1, while 1-HDPE-g-MA exhibits a slightly lower activity, particularly for the blends, in which PA is the matrix phase.     

Effects of electron beam irradiation on the structure–property behavior of blends based on low density polyethylene and styrene-ethylene-butylene-styrene-block copolymers

Low density polyethylene (LDPE) blends with different additives were exposed to various doses of electron beam irradiation. The additives used were styrene-ethylene-butylene-styrene-block copolymers (SEBS), styrene-ethylene-butylene-styrene-block copolymer grafted with maleic anhydride (SEBS-g-MA) and mineral compounds. The structure–property behavior of electron beam irradiated blends was characterized in terms of mechanical, thermal, and electrical resistivity properties. The results indicated that the unirradiated LDPE blends with the different compositions showed improved mechanical properties, thermal and volume resistivity properties than pure LDPE. However, the improvement in properties of unirradiated blends by using SEBS-g-MA was higher than using SEBS copolymer. Further improvement in the mechanical, thermal and electrical properties of the LDPE blends was achieved after electron beam irradiation. The limited oxygen index (LOI) data revealed that the LDPE/SEBS-g-MA/ATH blend was changed from combustible to self-extinguishing material after electron beam irradiation to a dose of 100 kGy. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of microstructure and flexibility of maleated styrene-b-(ethylene-co-butylene)-b-styrene rubber on the mechanical properties of polyamide 12

The present investigation deals with the mechanical and morphological properties of binary polyamide 12/maleic anhydride-grafted styrene-b-(ethylene-co-butylene)-b-styrene rubber (PA12/SEBS-g-MA) blends at varying dispersed phase (SEBS-g-MA) concentrations. Tensile behavior, impact strength and crystallinity of these blend systems were evaluated. Influence of microstructure, dispersed phase particle size, and ligament thickness on the impact toughness of the blend was studied. DSC data indicated an increase in crystallinity of PA12 in the blends. Tensile modulus and strength decreased while impact strength and elongation-at-break increased with the elastomer concentration. The enhanced properties were supported by interphase adhesion between the grafted maleic groups of rubber with polar moiety of polyamide 12. Analysis of the tensile data employing simple theoretical models showed the variation of stress concentration effect with blend composition.     

Optimum toughening via a bicontinuous blending: toughening of PPO with SEBS and SEBS-g-maleic anhydride

The poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) was toughened by melt extrusion through its blending with a styrene-b-ethylene/butadiene-b-styrene triblock copolymer (SEBS), or with maleic anhydride (MA) grafted SEBS (SEBS-g-MA). Their morphology, mechanical properties, and rheology have been investigated. Transmission electron microscopy revealed that both kinds of blends had an island-sea structure at low concentrations of SEBS or SEBS-g-MA and a bicontinuous one at sufficiently high concentrations. However, the percolation threshold was higher for SEBS than for the SEBS-g-MA. The Izod impact strength of PPO could be significantly improved through its blending with SEBS-g-MA, particularly in a blend with 20 wt% of SEBS-g-MA at which it had a maximum value. The rheological experiments indicated that the incorporation of SEBS increased and that of SEBS-g-MA decreased the melt viscosity of the system.     

Morphological,thermal, rheological,and mechanical properties of PP/EVOH blends compatibilized with PP‐g‐IA

We prepared some blends of polypropylene (PP) and ethylene vinyl alcohol (EVOH) with and without a compatibilizer. As a new compatibilizer, we synthesized polypropylene grafted with itaconic acid (PP‐g‐IA) using Brabender mixing system. We investigated the morphological, thermal, rheological, and mechanical properties of a compatibilized blends (PP/EVOH/PP‐g‐IA) and not compatibilized blends (PP/EVOH). Our experiments showed that carboxylic acid groups in PP‐g‐IA and hydroxyl group in EVOH formed strong in situ hydrogen bond in the compatibilized blends, resulting in better morphological and mechanical properties of the compatibilized blends than those of not compatibilized blends. POLYM. ENG. SCI., 56:1240–1247, 2016. © 2016 Society of Plastics Engineers     

Miscibility,phase behavior,and mechanical properties of ternary blends of poly(vinyl chloride)/polystyrene/chlorinated polyethylene-graft-polystyrene

The effectiveness of chlorinated polyethylene-graft-polystyrene (CPE-g-PS) as a polymeric compatibilizer for immiscible poly(vinyl chloride)/polystyrene (PVC/PS) blends was investigated. The miscibility, phase behavior, and mechanical properties were studied using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), Izod impact tests, tensile tests, and scanning electron microscopy (SEM). DSC and DMA studies showed that PVC is immiscible with chlorinated polyethylene (CPE) in CPE-g-PS, whereas the PS homopolymer is miscible with PS in CPE-g-PS. The PVC/PS/CPE-g-PS ternary blends exhibit a three-phase structure: PVC phase, CPE phase, and PS phase that consisted of a PS homopolymer and PS in CPE-g-PS. The mechanical properties showed that CPE-g-PS interacts well with both PVC and PS and can be used as a polymeric compatibilizer for PVC/PS blends. CPE-g-PS can also be used as an impact modifier for both PVC and PS. SEM observations confirmed, after the addition of CPE-g-PS, improvement of the interfacial adhesion between the phases of the PVC/PS blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 995–1003, 1998     

Comparison of the toughening behavior of nylon 6 versus an amorphous polyamide using various maleated elastomers

The toughening effect of two types of elastomers based on ethylene/α-olefin copolymers, viz, an ethylene/propylene copolymer (EPR) with its maleated version, EPR-g-MA, and an ethylene/1-octene copolymer (EOR) with its maleated versions, EOR-g-MA-X% (X=0.35, 1.6, 2.5), for two classes of polyamides: semi-crystalline nylon 6 versus an amorphous polyamide (Zytel 330 from DuPont), designated as a-PA, was explored. The results are compared with those reported earlier based on a styrenic triblock copolymer having a hydrogenated midblock, SEBS, and its maleated version, SEBS-g-MA, elastomer system. Izod impact strength was examined as a function of rubber content, rubber particle size and temperature. All three factors influence the impact behavior considerably for the two polyamide matrices. The a-PA is found to require a somewhat lower content of rubber for toughening than nylon 6. Very similar optimum ranges of rubber particle sizes were observed for ternary blends of EOR-g-MA/EOR with each of the two polyamides while blends based on mixtures of EPR-g-MA/EPR and SEBS-g-MA/SEBS (where the total rubber content is 20% by weight) show only an upper limit for a-PA but an optimum range of particle sizes for nylon 6 for effective toughening. Higher EPR-g-MA contents lead to lower ductile-brittle transition temperatures (T_db) as expected; however, a-PA binary blends with EPR-g-MA have a much lower T_db than do nylon 6 blends when the content of the maleated elastomer is not high. A minimum in plots of ductile-brittle transition temperature versus particle size appears for ternary blends of each of the matrices with EOR-g-MA/EOR; blends based on SEBS-g-MA/SEBS, in most cases, show higher ductile-brittle transition temperatures, regardless of the matrix. However, blends with EPR-g-MA/EPR show comparable T_db with those based on EOR-g-MA/EOR for the amorphous polyamide but show the lowest ductile-brittle transition temperatures for nylon 6 within the range of particle sizes examined. For the blends with a bimodal size distribution, the global weight average rubber particle size is inappropriate for correlating the Izod impact strength and ductile-brittle transition temperature. In general, trends for this amorphous polyamide are rather similar to those of semi-crystalline nylon 6.     

Ethylene vinyl alcohol copolymer/high density polyethylene blends compatibilized through functionalization

In order to evaluate the compatibilizing effects of isocyanate (NCO) functional groups on ethylene vinyl alcohol copolymer/high density polyethylene (EVOH/HDPE) blends, HDPE grafted with 2-hydroxyethyl methacrylate-isophorone diisocyanate (HDEP-g-HI) was prepared and blended with EVOH. The grafting was confirmed by infrared spectra, and the grafting ratio was 4.9% from elementary analysis. From the morphologies of EVOH/HDPE-g-HI blends, it was found that an improved adhesion between the two components and finer dispersions were produced as a result of chemical reactions occurring during the melt blending. The depression of melting temperature of EVOH in the 10/90 EVOH/HDPE-g-HI blend indirectly indicated increased miscibility. The tensile strength of the EVOH/HDPE-g-HI blend was much higher than that of the EVOH/HDPE blend having no adhesion at each composition, and a dramatic increase in the impact strength was produced at the 90/10 EVOH/HDPE-g-HI blend composing of the fine HDPE-g-HI dispersions.     

Compatibilization of polyethylene terephthalate/polypropylene blends with styrene–ethylene/butylene–styrene (SEBS) block copolymers

Blends of polyethylene terephthalate (PET) and polypropylene (PP) at compositions 20/80 and 80/20 were modified with three different styrene–ethylene/butyl–ene-styrene (SEBS) triblock copolymers with the aim of improving the compatibility and in particular the toughness of the blends. The compatibilizers involved an unfunctionalized SEBS and two functionalized grades containing either maleic anhydride (SEBS-g-MAH) or glycidyl methacrylate (SEBS-g-GMA) grafted to the midblock. The effects of the compatibilizers were evaluated by studies on morphology and mechanical, thermal and rheological properties of the blends. The additon of 5 wt % of a SEBS copolymer was found to stabilize the blend morphology and to improve the impact strength. The effect was, however, far more pronounced with the functionalized copolymers. Particularly high toughness combined with rather high stiffness was achieved with SEBS-g-GMA for the PET-rich composition. Addition of the functionalized SEBS copolymers resulted in a finer dispersion of the minor phase and clearly improved interfacial adhesion. Shifts in the glass transition temperature of the PET phase and increase in the melt viscosity of the compatibilized blends indicated enhanced interactions between the discrete PET and PP phases induced by the functionalized compatibilizer, in particular SEBS-g-GMA. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:241–249, 1997     

Influence of thermoplastic elastomers on mechanical properties and morphologies of isotactic polypropene/glass bead hybrid composites

Glass bead-reinforced isotactic polypropene hybrid composites containing 0–20 vol % thermoplastic elastomers were prepared to study both structure/property relationship and morphology development. Polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS-g-MA) were used as thermoplastic elastomers. Hybrid composites containing SEBS gave higher Young's moduli than did those containing SEBS-g-MA. The experimental Young's moduli were in good agreement with the theoretical predictions according to Lewis and Nielsen. The lower moduli of hybrid composites containing SEBS-g-MA were attributed to interlayer formation and in situ encapsulation of glass beads, resulting in core–shell particles. This elastomeric interlayer impaired the filler reinforcement. Analysis of tensile yield stress and results of lap-shear tests confirmed strong filler–polymer interactions in composites containing SEBS-g-MA. Only in excess of a critical volume fraction did SEBS-g-MA afford a significant improvement of the notched Izod impact strength. In contrast to stiffness, Izod impact strength was not influenced by the type of elastomer and morphology. Investigation of crystallization and scanning electron microscopic studies proved the in situ encapsulation of the glass beads with SEBS-g-MA, whereas SEBS addition results in separately dispersed glass beads and SEBS microphases. © 1996 John Wiley & Sons, Inc.     

Reactive compatibilizer precursors for LDPE/PA6 blends. II: maleic anhydride grafted polyethylenes

Several home made and commercially available polyethylene (PE) samples grafted with maleic anhydride (MA) (PE-g-MA) were used as compatibilizer precursors (CPs) for the reactive blending of low density PE (LDPE) with polyamide-6 (PA). Scope of the work was to compare the effectiveness of these CPs with that of a number of ethylene-acrylic acid copolymers (EAA), which had been employed in a previous study for the reactive compatibilization of the same blends, and to get a deeper insight into the coupling reactions producing the PA-g-CP copolymers that are thought to act as the true compatibilizers in these systems. To this end, binary CP/LDPE and CP/PA and ternary LDPE/PA/CP blends were prepared with a Brabender mixer and were characterized by DSC, SEM and solvent fractionation. The results show that the PE-g-MA copolymers react more rapidly with PA than the EAA copolymers and that their CP effectiveness depends critically on the microstructure and the molar mass of their PE backbones. In particular, the CPs produced by functionalization of LDPE were shown to be miscible with this blend component and to be scarcely available at the interface where reaction with PA is expected to occur. Conversely, the CPs prepared from the HDPE grades were immiscible with LDPE and showed better CP performance. Whereas the effectiveness of the EAA copolymers studied earlier had been shown to increase with an increase in the concentration of the carboxyl groups, the concentration of the succinic anhydride groups of the PE-g-MA CPs studied in this work was found to play a minor role, at least in the investigated range (0.3-3.0 wt% MA).