聚丙烯无纺布预辐射固相接枝丙烯酸的研究

以聚丙烯(PP)无纺布为基材,以丙烯酸为单体,进行预辐射固相接枝聚合,考察了外部环境、辐射剂量、温度、反应时间、单体用量、介质、阻聚剂、交联剂对接枝率的影响。结果表明,通过预辐射固相接枝聚合方法,可将丙烯酸单体接枝在PP无纺布上,辐射剂量增大可提高接枝率;反应时间对接枝率的影响在低、高温阶段有所不同。最佳反应条件为:氮气环境,辐射剂量大于50 kGy,反应温度65℃,反应时间3 h,单体浓度30%,反应介质为水,阻聚剂0.8 g,交联剂用量为5 mL。     

聚丙烯无纺布接枝改性研究

采用Co射线辐射后的聚丙烯(PP)无纺布为原料,通过接枝改性制备PP接枝共聚物。研究了接枝条件对接枝率的影响。结果表明:选择丙烯酸为接枝单体,其质量分数为30%,交联剂质量分数5%,阻聚剂用量0.30 g,接枝反应温度65℃,反应时间3 h,PP无纺布的接枝改性效果显著,接枝率达84.95%。     

丙烯酸接枝改性丙纶非织造布的吸附与解吸研究

采用丙烯酸接枝改性聚丙烯非织造布(PP-g-AA)对阳离子红X-GRL染料进行吸附与解吸,探讨了PP-g-AA对染料的吸附动力学机理、解吸过程和解吸动力学机理,以及基于动态吸附的过滤分离操作,分析了PP-g-AA对染料吸附-解吸再生循环利用的可行性。结果表明:不同初始染料浓度下,PP-g-AA的吸附动力学符合Lagergren's准二级动力学模型和双指数模型;解吸液的最佳配比为表面活性剂质量分数5%,乙醇与水的体积比3∶7,解吸率随吸附量的增大呈现先增大后减小的趋势,解吸符合Lagergren's准二级动力学模型;动态吸附-解吸再生循环10次后,染料的去除率达96%以上,再生循环8次时,PP-g-AA的跨膜压力为37.1 k Pa,水通量最大达38.6 L/(m2·h)。     

聚丙烯无纺布预辐射接枝改性及胺化研究

采用丙烯酸(AA)、二乙烯三胺(DETA)依次对聚丙烯(PP)无纺布进行预辐射接枝改性及胺化处理,研究了接枝反应及胺化反应的影响因素,并用红外光谱对产物进行表征。结果表明:随着AA用量的增加,接枝率呈先增长后下降趋势;随着反应温度的升高,反应时间的延长,接枝率增加;随着接枝率的增大,胺化反应温度的升高及反应时间的增加,胺化率增加。接枝反应温度为95℃,25 mL AA与无纺布反应2 h,接枝率可达到276%;接枝率为250%的无纺布与50 mL DETA反应7 h,胺化温度205℃,胺化率可达到73%。红外光谱分析表明,经辐射接枝及胺化处理后的PP无纺布有胺基基团。     

丙烯酸改性氯化聚丙烯的合成和粘接性能的研究

氯化聚丙烯是聚丙烯的氯化改性产物，通过改性，其硬度、耐磨性、耐酸性、耐盐水性能比聚丙烯都好，耐热、耐老化性也优于聚丙烯。但其性能尤其是粘接性能还不能满足其在胶粘刺等方面的需要，为了进一步提高氯化聚丙烯的粘接性能，拓宽其应用领域，需对氯化聚丙烯改性。接枝共聚法是一种很好的化学改性方法。本文以丙烯酸(AA)作为接枝单体，以过氧化苯甲酰(BPO)为引发剂，以甲苯为溶刺，采用液相接枝共聚法，将丙烯酸单体接枝到氯化聚丙烯大分子链上，得到丙烯酸改性氯化聚丙烯产物。系统研究了反应温度、反应时间、引发剂过氧化苯甲酰用量和丙烯酸单体用量等因素对丙烯酸接枝改性的氯化聚丙烯产物粘接性能的影响，得出了较佳的工艺条件是反应温度T=100℃，反应时间t=3．5h，原料质量配比为100份氯化聚丙烯、3份丙烯酸和0．3份的过氧化二苯甲酰。研究还表明，丙烯酸改性的氯化聚丙烯的粘接性能优于氯化聚丙烯的粘接性能。     

Radiation grafting of acrylic acid on to polypropylene filaments. I: Effect of reaction conditions

Graft copolymerization of acrylic acid on to polypropylene filaments was investigated by a simultaneous irradiation technique. The effect of various solvents and solvent combinations on swelling behaviour and on percentage grafting was studied. At a constant dose, the percentage grafting was found to be higher at low dose rates and it increased linearly up to 0.25 Mrad and then saturated. It was also observed that grafting increases with increasing monomer concentration up to 2 mole/litre. Graft copolymers were characterized by infrared spectroscopy and colour formation with methylene blue.     

聚丙烯纤维接枝丙烯酸反应条件优化

The optimum conditions of grafting copolymerization reaction of acrylic acid (AA) onto polypropylene (PP) fiber was studied by using benzoyl peroxide (BPO) as initiator. The primary and secondary sequences of the grafting copolymerization reaction conditions was analysed. The results showed that grafting copolymerization reaction was greatly influenced by the temperature, reaction time, concentration of BPO and that of AA in the primary and secondary role as the above sequence. The optimum reaction conditions of gaining higher exchange capacity for the weak acidic cation-exchange fiber are as follows: the grafting temperature 80℃, the reaction time 7h, the concentration of BPO 2% and AA 80%.     

超声波在丙烯酸固相接枝聚丙烯中的应用

利用超声波促进固相接枝反应的原理，研究丙烯酸（AA）接枝聚丙烯（PP）的反应条件：超声波作用时间、接枝反应温度、引发剂过氧化苯甲酰（BPO）及AA用量等对接枝率的影响。研究表明：超声波能有效地促进固相接枝反应的进行。其最佳反应条件是：超声波的作用时间为30min，BPO与AA的用量分别为4％和15％，反应温度为110℃。在上述反应条件下，可以得到接枝率为6％的接枝产物AA接枝PP（PP－g－AA）；并用硅灰石填充含有PP-g-AA的PP复合材料，其力学性能明显优于不含PP－g－AA的硅灰石填充的PP复合材料。     

等规聚丙烯-丙烯酸接枝共聚

详细研究了等规聚丙烯细粒子在丙烯酸水溶液中,以过氧化苯甲酰为引发剂的液－固相接枝共聚反应和十氢化萘乙醇溶液对等规聚丙烯的膨化预处理作用,检测了等规聚丙烯－聚丙烯酸的某些性质,发现随接枝率提高,其吸湿性和碱性染料染色性均提高,熔点略有降低,但熔体流动性下降,按本研究获得的最佳膨化预处理条件和最佳接枝共聚反应条件,接枝产物等规聚丙烯－聚丙烯酸的接枝率可超过13％。     

聚丙烯无纺布预辐射法固相接枝甲基丙烯酸甲酯的研究

研究了以预辐射聚丙烯无纺布为基材,甲基丙烯酸甲酯为单体,采用固相接枝聚合的方法制备接枝共聚物的接枝反应过程。详细讨论了反应温度、反应时间、阻聚剂、单体浓度和交联剂等对接枝率的影响。结果表明,该接枝反应的最佳条件为:温度65℃、时间2 h、单体浓度20%、交联剂5%、阻聚剂(FeSO4.7H2O)0.3 g,在此条件下的接枝率为6.64%。     

PP无纺布预辐射法固相接枝4-VP的研究

以预辐射聚丙烯无纺布为基材,4-乙烯基吡啶为单体,二乙烯基苯为交联剂,采用固相接枝聚合的方法制备接枝共聚物。讨论了反应温度、反应时间、阻聚剂、单体浓度和交联剂等对接枝率的影响。结果表明,接枝反应的最佳条件为:温度50℃,时间3 h,单体浓度10%,交联剂5%,阻聚剂(FeSO4.7H2O)0.08%,最佳条件下的接枝率为7.5%。     

丙烯酸改性卤锑阻燃聚丙烯的结晶性能

研究了丙烯酸(AA)改性Sb2O3,聚丙烯(PP)母料制备的不同用量卤锑阻燃PP。阻燃PP的差示扫描量热法结果表明,阻燃剂在PP中存在明显的异相成核作用,使PP结晶温度提高,Sb2O3对PP的异相成核作用比十溴二苯醚明显。在无引发剂过氧化二异丙苯(DCP)存在下,AA对阻燃PP中PP结晶温度的影响取决于阻燃剂的用量;在DCP存在下,PP的结晶温度不随AA用量增加而改变。DCP用量增加导致PP严重降解,结晶温度与熔融温度降低。     

Plasma induced graft polymerization of acrylic acid onto polypropylene monofilament

Plasma induced graft polymerization of acrylic acid onto polypropylene (PP) monofilament was carried to introduce carboxyl functionality on its surface. The monofilament was treated with oxygen plasma to create hydroperoxide groups and subsequent graft polymerization was initiated on this exposed monofilament. It was observed that in the absence of an added inhibitor, the grafting did not proceed because of the extensive homopolymerization which left behind hardly any monomer for the grafting reaction. The addition of ferrous sulfate to the grafting medium led to the homopolymer free grafting reaction. The addition of organics, such as methanol, butanone, and acetone led to complete inhibition of the homopolymerization at 60% content. However, the addition of butanone led to much lower degree of grafting than methanol and acetone. The contact angle of the monofilament showed drastic reduction by plasma treatment and by the subsequent grafting of acrylic acid. The grafting in ferrous sulfate medium showed higher contact angles as compared to the grafting in organic medium. The surface morphology was significantly influenced by the nature of the additive in the grafting medium. © 2007 Wiley Periodicals, Inc. JAppl Polym Sci, 2008     

Graft polymerization of acrylic acid onto polypropylene monofilament by RF plasma

Plasma‐induced graft polymerization of acrylic acid onto polypropylene monofilament was carried out to introduce carboxyl groups on its surface. The monofilament was treated with oxygen plasma to create hydroperoxide groups and subsequent graft polymerization of acrylic acid on exposed filament was carried out. An increase in the plasma power led to higher graft levels. It was observed that the hydroperoxide build up on PP surface follows linear increase with the increase in the plasma treatment time only up to 180 s beyond which it slowed down significantly. The formation of oxygenated species was ascertained by X‐ray photoelectron spectroscopy, and the peroxide content was measured by the 2′‐diphenylpicrylhydrazyl (DPPH) estimation. The grafting was observed to be considerably influenced by the plasma exposure time, plasma power, reaction temperature, monomer concentration and the storage temperature. A maximum in the degree of grafting was observed at 40% monomer concentration beyond which grafting tended to decrease very fast. The grafting was also found to be maximum at 50°C followed by a sharp decrease, subsequently. The storage of the exposed filament at ?80°C led to the identical grafting all along the 16 days. However, the storage at 25°C showed significant reduction in the degree of grafting. The atomic force microscopy showed that surface morphology is transformed into a nonhomogeneous one after the plasma exposure, but tends to flatten out after the grafting process in the form of globular structures. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Direct radiation grafting of acrylic acid to nylon-6 fabric and the behaviour of the resulting graft copolymer

The role of certain cations as homopolymer inhibitors in the direct radiation grafting of acrylic acid to nylon-6 fabric was investigated. The grafting solution was methanol and water at a ratio of 30 : 70 vol%. The maximum graft yield was obtained at 0·08 wt% when using Fe²⁺ and at 0.7% for Fe³⁺. In addition, the graft yield obtained with the latter ion was higher than that for the former. Moreover, the presence of Na⁺ and K⁺ salts in concentrations as low as 0·1 wt% caused an increase in the graft yield. The hydrophilic properties investigated indicated that the water absorption of nylon-6 fabric after 9 days increased by 44 times after grafting with poly(acrylic acid) at 166% graft yield. This ratio became 123 times, when this graft copolymer was transformed to the sodium salt. These ratios became 105 and 490 times for the corresponding recrystallized forms, respectively. A study was made to gain a better understanding of the observed super water absorption using SEM and DSC analysis. SEM micrographs of the recrystallized copolymer indicated the formation of large pores with a dendritic structure. Moreover, DSC showed a decrease in both the heat of fusion and melting point. The grafted nylon-6 fabric showed a noticeable affinity for different dyestuffs.     

Graft copolymerization of mixtures of acrylic acid and acrylamide onto polypropylene film

Liquid phase ultraviolet irradiation in the presence of benzophenone as a photosensitizer and barium hydroxide as a pH controller were used to graft the mixtures of acrylic acid and acrylamide to a polypropylene surface. The surface of the grafted polypropylene samples were characterized by Fourier transform infrared spectroscopy‐attenuated total reflectance, electron spectroscopy for chemical analysis, scanning electron microscopy, and a contact angle meter. The pH value of the reaction medium that produced the graft with equal molar ratio was found to be ∼ 3.77. The optimal reaction condition was found at a monomer feed of 25%, a reaction time of 30 min, and a benzophenone concentration of 1%. Surface tension of the samples increased to a value of 40 dyn cm⁻¹ due to the graft of the hydrophilic monomers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 251–256, 1999     

丙烯酸改性氯化聚丙烯乳液

采用溶液法对氯化聚丙烯进行接枝改性,得到丙烯酸改性的氯化聚丙烯和聚丙烯酸酯的混合物,加胺中和后用水直接分散得到自乳化水性丙烯酸改性氯化聚丙烯乳液。考察了单体用量对改性乳液性能的影响,结果表明,当单体与氯化聚丙烯的质量比为0.6～1.5时,制得的乳液具有良好的稳定性和优异的附着力。用光学显微镜对改性乳液的粒子形态进行了观察,结果表明接枝氯化聚丙烯处于乳胶粒的核层,而聚丙烯酸酯处于乳胶粒的壳层。     

Study of electron beam preirradiation-induced graft copolymerization of acrylic acid onto powdered isotactic polypropylene

In order to obtain required polymer materials, acrylic acid was grafted onto powdered isotactic polypropylene by an electron beam preirradiation technique. All processes (including irradiation, storage of the samples, and grafting polymerization) were carried out in air. The effects of irradiation dose, storage time, reaction temperature, morh's salt, acid, and monomer concentration were investigated and discussed in detail. The results show that the grafting can be achieved well without purging oxygen, and morh's salt is indispensable for initiating grafting reaction and decreasing the homopolymerization. Optimal reaction conditions can be generalized for large-scale production of the desired polymer materials. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1357–1362, 1999     

Plasma-induced hydrogel grafting of vinyl monomers on polypropylene

Polypropylene (PP) film was plasma-treated using a 13.56 MHz direct plasma with argon, nitrogen, and oxygen as the plasma-forming gases. The three gases induced very different changes on the PP film surface, which were studied using contact angle measurements. Because of its degrading and oxidative effect, oxygen plasma pretreatment was not used for the homogeneous grafting of acrylic acid and acrylamide. Nitrogen plasma treatment did not lead to the formation of stable peroxides on the film surface and did not undergo grafting reactions. This may be due to the types of radicals and functional groups created on the surface during the plasma treatment. Finally, argon plasma pretreatment was found to be the most effective for the grafting of vinyl monomers. The amount of grafted poly(acrylic acid) was shown to be proportional to the concentration of peroxides created by argon plasma treatment.     

Kinetics study of radiation‐grafting of acrylic acid,acrylonitrile, and their mixture onto wool fabric

The effect of monomer concentration, exposure time, irradiation temperature, and weaving direction on the kinetics of grafting acrylic acid (AA), acrylonitrile (AN), and their mixture onto wool fabric has been studied at the dose rate of 1.38 Gy/s. The degree of grafting is found to depend on the methanol‐to‐water solvent ratio and fabric‐to‐liquor ratio. The grafting rate and rate constant are dependent on irradiation temperature, type of grafted monomer, and weaving direction. The grafting rates increase with the increase in irradiation temperature (276–308 K). The calculated activation energy is nearly the same (16.4–17.2 kJ mol^?1) and the preexponential rate constant is dependent on the type of grafted monomer. The grafting of AA, AN, and their mixture are confirmed from the dyeing affinity of grafted fabrics towards Sandocryl Blue (SB), a basic dye. The formation of wool grafts and structural changes resulting from grafting were verified by using FTIR spectrometry and X‐ray diffraction analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4328–4340, 2006