Thermal decomposition of cellulose ethers

The thermostability and thermal decomposition kinetics of methyl cellulose (MC), ethyl cellulose (EC), carboxymethyl cellulose (CMC), hydroxyethyl cellulose (HEC), and hydroxypropyl–methyl cellulose (HPMC) were characterized in nitrogen and air by thermogravimetry (TG). Various methods of kinetic analysis were compared in case of thermal degradation of the five cellulose ethers. The initial decomposition temperature (T_d), temperature at the maximum decomposition rate (T_dm), activation energy (E), decomposition reaction order (n), and pre-exponential factor (Z) of the five cellulose ethers were evaluated from common TG curves and high-resolution TG curves obtained experimentally. The decomposition reactions in nitrogen were found to be of first order for MC, EC, and HPMC with the average E and ln Z values of 135 kJ/mol and 25 min⁻¹, although there were slight differences depending on the analytical methods used. The thermostability of cellulose ethers in air is substantially lower than in nitrogen, and the decomposition mechanism is more complex. The respective average E, n, ln Z values for HEC in nitrogen/air were found to be 105/50 kJ/mol, 2.7/0.5, and 22/8.3 min⁻¹, from constant heating rate TG method. The respective average E, n, and ln Z values for three cellulose ethers (EC/MC/HPMC) in air are 123/144/147 kJ/mol, 2.0/1.8/2.2, 24/28/28 min⁻¹ by using high-resolution TG technique. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2927–2936, 1999     

Aerobic biodegradation of cellulose acetate

Two separate assay systems were used to evaluate the biodegradation potential of cellulose acetate: an in vitro enrichment cultivation technique (closed batch system), and a system in which cellulose diacetate (CDA) films were suspended in a wastewater treatment system (open continuous feed system). The in vitro assay employed a stable enrichment culture, which was initiated by inoculating a basal salts medium containing cellulose acetate with 5% (v/v) activated sludge. Microscopic examination revealed extensive degradation of CDA (DS = 2.5) fibers after 2–3 weeks of incubation. Characterization of the CA fibers recovered from inoculated flasks demonstrated a lower average degree of substitution and a change in the mol wt profiles. In vitro enrichments with CDA (DS = 1.7) films were able to degrade > 80% of the films in 4–5 days. Cellulose acetate (DS = 2.5) films required 10–12 days for extensive degradation. Films prepared from cellulose triacetate remained essentially unchanged after 28 days in the in vitro assay. The wastewater treatment assay was less active than the in vitro enrichment system. For example, approximately 27 days were required for 70% degradation of CDA (DS = 1.7) films to occur while CDA (DS = 2.5) films required approximately 10 weeks before significant degradation was obtained. Supporting evidence for the biodegradation potential of cellulose acetate was obtained through the conversion of cellulose [1-¹⁴C]-acetate to ¹⁴CO₂ in the in vitro assay. The results of this work demonstrate that cellulose acetate fibers and films are potentially biodegradable and that the rate of biodegradation is highly dependent on the degree of substitution. © 1993 John Wiley & Sons, Inc.     

Studies on thermal degradation of cellulose and cellulose phosphoramides

Reaction of cellulose with hexamethylphosphoric acid triamide has been investigated under various physical conditions. Dimethylamine hydrochloride was found to be an efficient catalyst for the system. The thermal degradation of cellulose and its phosphoramide products in air was studied by DTA, TG, and DTG techniques from ambient temperature to 500°C. The data were processed for the various thermodynamic parameters following the methods of Freeman and Carroll, of Broido, and of Dave and Chopra. The energies of activation, E_a, for the degradation for various cellulose phosphoramide samples were found to be in the range of 92–136 kJ mol^?1. These values were found to decrease with increase in the degree of substitution. A mechanism for the thermal degradation of cellulose phosphoramide has been proposed. The IR spectra of char residues of cellulose phosphoramide gave an indication of the formation of compounds containing C?O and P?O groups.     

Blends of cellulosic esters with poly(caprolactone): Characterization by DSC,DMA, and WAXS

Binary blends of poly(caprolactone) (PCL) with cellulosic esters [cellulose diacetate (CDA), cellulose acetate–butyrate (CAB), and cellulose triacetate (CTA)] were studied by using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and wide-angle X-ray scattering (WAXS) techniques, and qualitative comparison was made with the results obtained by polarizing optical microscopy. The PCL–CAB system was proved to be partially miscible, whereas PCL–CDA and PCL–CTA appeared to be immiscible. A double-melting behavior was showed for PCL–CAB and PCL–CTA blends. As these peaks did not shift by varying the heating rate of DSC runs, this behavior can be due to melting of two populations of crystals of PCL, which may be different in size. On the other hand, blends of PCL containing a low amount of CAB or CDA seem to develop more crystallinity for the PCL than this polymer alone. The solvent seems to have a certain influence on the thermal and morphological behaviors of the as-cast blends of these three systems, affecting the extent of crystallinity of PCL, as well as its T_m and ΔH_f. This finding is discussed in the light of WAXS and polarizing optical microscopy results. © 1994 John Wiley & Sons, Inc.     

Plasticization of cellulose diacetate by reaction with maleic anhydride,glycerol, and citrate esters during melt processing

To accomplish the stable internal plasticization of cellulose diacetate (CDA), maleic anhydride (MAH) and glycerol (Gly) were used as reactive plasticizers. The plasticization method used was based on a melt‐processing reaction of CDA with MAH and Gly. MAH and Gly (MG)‐plasticized CDA showed stiff and brittle properties; that is, low elongation at break and high modulus. Thus, citrate esters were used as coplasticizers to improve physical properties. The resulted plasticized materials were optically clear, and showed attractive mechanical properties. The grafting of MG oligoesters to the free hydroxyl groups in CDA and their homo‐oligomerization were accelerated by two‐step kneading process, and verified by FTIR and GPC measurements. Differential scanning calorimeter (DSC) analysis revealed decreases of 80–100°C in the glass transition temperature (T_g) of CDA by these plasticizations. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 243–250, 2001     

High‐resolution thermogravimetry of cellulose esters

Cellulose dinitrate (CDN), cellulose diacetate (CDA), and cellulose triacetate (CTA) were subjected to high‐resolution thermogravimetry (TG) at a variable heating rate in air. The TG curves, the derivative TG curves, the second derivative TG curves, and heating rate curves are discussed. The thermal degradation temperature and kinetic parameters are presented and compared to those obtained with traditional TG at a constant heating rate. The degradation process of the cellulose esters is speculated. Among the three cellulose esters, CDN exhibits the lowest degradation temperature of (213°C) but the largest degradation activation energy of (237–269 kJ/mol). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 573–578, 1999     

Thermogravimetry of Thermoplastic Polyimide Powders under Four Different Atmospheres

Thermal degradation of a thermoplastic polyimide ( TPI ) fine powder was studied in nitrogen, helium, argon, and air, from room temperature to 790°C by a high‐resolution thermogravimetry (TG) at a variable heating rate in response to changes in the weight‐loss rate of the sample and also by traditional TG. In the three inert atmospheres, the high‐resolution TG found a two‐step degradation process with higher resolution for the TPI , which was hardly ever revealed by a traditional TG for the TPI and other similar polyimides. On the contrary, only a traditional TG in air observed a two‐step degradation process for the TPI . The initial thermal degradation temperature T_d, the temperatures at the maximum weight‐loss rate T_dm1 and T_dm2, the first maximum weight‐loss rate (dα/dT)_m1, as well as the degradation activation energy of the TPI all increase with the variation of testing atmosphere in the following order: in nitrogen < in helium < in argon < in air, but the char yield at 700°C appears to increase in a different order: in air < in helium < in argon < in nitrogen.     

Preparation and properties of chemical cellulose from ascidian tunic and their regenerated cellulose fibers

Chemical cellulose (dissolving pulp) was prepared from ascidian tunic by modified paper‐pulp process (prehydrolysis with acidic aqueous solution of H₂SO₄, digestion with alkali aqueous solution of NaOH/Na₂S, bleaching with aqueous NaOCl solution, and washing with acetone/water). The α‐ cellulose content and the degree of polymerization (DPw) of the chemical cellulose was about 98 wt % and 918, respectively. The Japanese Industrial Standard (JIS) whiteness of the chemical cellulose was about 98%. From the X‐ray diffraction patterns and ¹³C‐NMR spectrum, it was found that the chemical cellulose obtained here has cellulose Iβ crystal structure. A new regenerated cellulose fiber was prepared from the chemical cellulose by dry–wet spinning using N‐methylmorpholine‐ N‐oxide (NMMO)/water (87/13 wt %) as solvent. The new regenerated cellulose fiber prepared in this study has a higher ratio of wet‐to‐dry strength (<0.97) than commercially regenerated cellulose fibers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1634–1643, 2002.     

Characterisation of cellulose treated by the steam explosion method. Part 3: Effect of crystal forms (cellulose I,II and III) of original cellulose on changes in morphology,degree of polymerisaion,solubility and supermolecular structure by steam explosion

An attempt was made to clarify the effect of the crystal form of untreated cellulose on the morphological and structural changes of cellulose during steam explosion treatment (steam pressure P = 2.9MPa (T = 508K), treatment time t = 15-300 s). For this purpose, the crystal form of soft wood pulp (cellulose I) was converted by solid-to-solid transition, with minimal unavoidable change in other structural characteristics including morphology and average degree of polymerisation, into cellulose II or cellulose III. It was proved by both X-ray and solid-state cross-polarisation/magic-angle sample-spinning (CP/MAS) ¹³C NMR analyses that even a simple addition of water at room temperature brought about a significant structural change in the steam-untreated cellulose samples. The solubility towards 9.1 wt% aqueous sodium hydroxide, S_a, of the cellulose samples of crystal forms I and III could be improved from 31-33% up to almost 100% by selecting appropriate steam explosion conditions (for example, P = 2.9MPa, t = 30 s). Such a magnificent increase in S_a by the steam explosion treatment was not observed for the cellulose II sample, even under the rather severe conditions of the steam explosion treatment at which the cellulose III crystal was converted to a large extent to cellulose I, as confirmed by X-ray diffraction. X-ray diffraction analysis showed that crystallisation of samples with cellulose I or II crystal occurred to some extent during the steam explosion treatment. Contrary to this, the degree of breakdown of the intramolecular hydrogen bond O₃…O'₅, as estimated by CP/MAS ¹³C NMR analysis, significantly increased for cellulose I and I11 during the treatment. The decrease in the viscosity-average degree of polymerisation, P, observed for all treated samples can be roughly categorised into two or three steps of the first-order decomposition reaction with different reaction rates.     

Preparation and characterization of the copolymer containing N‐pyridyl bi(methacryl)imide unit

The copolymer of methacrylic acid anhydride and N‐2‐pyridyl bi(methacryl)imide was prepared based on the reaction of polymethacrylic acid with 2‐pyridylamine. The molecular structure was characterized by ¹H‐NMR, FTIR, UV–Vis, and circular dichroism techniques. The physical properties of polymethacrylic acid change significantly after an introduction of 6 mol % N‐2‐pyridyl bi(methacryl)imide unit. In particular, the thermal degradation of the polymer was systematically studied in flowing nitrogen and air from room temperature to 800°C by thermogravimetry at a constant heating rate of 10°C/min. In both atmospheres, a four‐stage degradation process of the copolymer of methacrylic acid anhydride and N‐2‐pyridyl bi(methacryl)imide was revealed. The initial thermal degradation temperature T_d, and the first, second, and third temperatures at the maximum weight‐loss rate T_dm1, T_dm2, and T_dm3 all decrease with decreasing sample size or changing testing atmosphere from nitrogen to air, but the fourth temperature at the maximum weight‐loss rate T_dm4 increases. The maximum weight‐loss rate, char yield at elevated temperature, four‐stage decomposition process, and three kinetic parameters of the thermal degradation were discussed in detail. It is suggested that the copolymer of methacrylic acid anhydride and N‐2‐pyridyl bi(methacryl)imide exhibits low thermal stability and multistage degradation characteristics. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1673–1678, 2002     

The use of DTA to study spontanceous ignition of cellulose

The use of differential thermal analysis has enabled spontaneous ignition behaviour of cotton cellulose to be investigate. The temperature. T_i, at which the onset of spontaneous ignition occurs is recorded as a function of the oxygen concentration of the flowing oxygen-nitrogen atmosphere to which the cellulose sample is exposed in the DTA furnace, when heated at a defined heating rate. The dependence of T_i, on heating rate has enabled the activation energy, E_p, of the rate-determining flammable pyrolysis product reaction to the determined using both a previously derived simple kinetic model and the technique of Ozawa. E_p, increases from a lower limiting value of 112 kJ mol^?1 at zero oxygen concentration to an asymptote value of 169 kJ mol^?1 at oxygen volume concentrations above 30%. This effect is described in terms of oxygen catalysis of competing pyrolysis routes. At a given heating rate, increased oxygen concentration reduces T_i. A plot of 1/T_i versus In [O₂] gives two liner regions which intersect at an oxygen concentration of about 20%, suggesting that two combustion mechanisms exist, one above and the other below this value. Below this concentration, which is similar to the conventional limiting oxygen for cellulose, significant char remains, suggesting that ignition of gaseous products only occurs. If the difference in slopes is sttributed to the variations in E_p with oxygen concentration, then a value for the activation energy of gaseous product oxidation, E_ox = 215 kJ mol^?1 is derived.     

New methods for acylation of pure and sawdust‐extracted cellulose by fatty acid derivatives—Thermal and mechanical analyses of cellulose‐based plastic films

This work deals with the synthesis of cellulosic plastic films obtained in homogeneous conditions by microwave‐induced acylation of commercial or chestnut tree sawdust cellulose by fatty acids. The acylation reaction was studied according to N,N‐dimethyl‐4‐aminopyridine (DMAP) amount, DMAP simultaneously playing the role of catalyst and proton trapping base. This study clearly showed that DMAP does not influence degrees of substitution (DS), massic, and molar yields. Plastic films synthesized in the absence of DMAP showed a decrease in mechanical behavior. Organic (tributylamine) or inorganic bases (CaCO₃, Na₂CO₃) were then added to replace DMAP basic activity, and no changes were observed. Concerning thermal and mechanical properties of plastics obtained with various bases, glass transition temperatures (T_g) and degradation temperature (T_d) were found constant whatever the base, and the best mechanical properties were obtained for films synthesized in the presence of CaCO₃. The same remarks were made concerning the valorization of chestnut tree sawdust cellulose. Microbial biodegradation of plastic films with DS = 2.2 led to a loss of their mechanical behaviors. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1266–1278, 2005     

Plasticization of cellulose diacetate by graft copolymerization of ε‐caprolactone and lactic acid

Graft copolymerization of ε‐caprolactone (CL) and lactic acid (LA) onto cellulose diacetate (CDA) at the residual hydroxyl positions was conducted to obtain thermoplastic CDA. The effects of the reaction temperature and time and the CL/LA molar ratio in the feed on the progress of the graft copolymerization were investigated. The molecular weight of CDA was increased by this graft copolymerization. The oxycaproyl and lactyl molar substitutions (MS_CL and MS_LA, respectively) in grafted CDA (g‐CDA) were determined through ¹H‐NMR spectral analysis. These MS values were controllable by changing the reaction conditions adequately. The flow temperature and melt viscosity of g‐CDA decreased with an increase in the total substitution of MS_CL and MS_LA, and transparent polymer sheets could be obtained from the resulting g‐CDA by hot pressing at around 200°C without adding any plasticizer. The mechanical properties of the molded g‐CDA samples varied widely, depending on the different combinations of the MS_CL and MS_LA values; the g‐CDA sheets became elastic when the MS_CL was larger than the MS_LA, and their tensile strengths were enhanced as the MS_LA was increased. It was thus found that CDA was successfully plasticized by this graft copolymerization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2621–2628, 2002     

Characterization and free radical polymerization of liquid crystalline acrylic acid/cellulose diacetate and N-vinyl-2-pyrrolidinone/cellulose diacetate solutions

Polymerizations of liquid crystalline solutions of cellulose diacetate (CDA) in acrylic acid (AA) and N-vinyl-2-pyrrolidinone (NVP) were conducted in an attempt to prepare molecular composites (polymer blends) processing a rigid rod polymer with liquid crystalline orientation. CDA was found to form liquid crystalline solutions in both AA and NVP at concentrations avove 40 wt% CDA. Polymerization of anisotropic 50 wt% CDA-AA and CDA-NVP solutions occurred with considerable retention of the starting solution anisotropy and yielded homogeneous blends (1 T_g) when the rate of polymerization was fast relative to the phase separation of the free radically polymerizing AA or NVP with CDA. Slow polymerizations lead to phase separated blends (2 T_g).     

Kinetics of isothermal and non‐isothermal degradation of cellulose: model‐based and model‐free methods

BACKGROUND: The kinetics of the thermal decomposition of cellulosic materials is of interest from the viewpoint of flame retardancy for safety, optimization of incineration processes and reducing energy production from fossil sources and associated pollution. One essential step in these processes is the thermal degradation through mass and energy transport, which determines the rate of evolution of various types of products from cellulosic materials. RESULTS: Kinetic parameters have been determined using various model‐based and model‐free methods in the thermal degradation of cellulose up to 700 °C in helium atmosphere. The values of the activation energy obtained in isothermal processes and non‐isothermal processes have been found to be not far from each other. From the integral method, the random nucleation (F₁)‐type mechanism has been found most probable for cellulose degradation having an activation energy, E_a, in the range 156.5–166.5 kJ mol^?1, lnA = 20–23 min^?1, for first‐order reaction during its decomposition process at heating rates of 2, 5 and 10 °C min^?1. Based on the high correlation coefficient, many types of mechanisms seem equally good for non‐isothermal degradation of cellulose. CONCLUSION: The linear correlation coefficient has a limitation for verifying the correctness of a reaction mechanism in the study of degradation kinetics. Therefore, the correctness of a mechanism should be considered on the basis of comparing the kinetic parameters obtained from isothermal as well as non‐isothermal methods. Copyright © 2008 Society of Chemical Industry     

Comparison of various solvents for determination of intrinsic viscosity and viscometric constants for cellulose

Different solvents used to determine the intrinsic viscosity and the viscometic constants, a and K, published in the literature for cellulose, were compared. The various parameters affecting the viscometric constants were also evaluated. The main conclusions obtained from the experimental data available in the literature are that (1) the intrinsic viscosities in various solvents are ordered as follows: [η]_LiCl/DMAc > [η]_NH3/NH4SCN ≥ [η]_FeTNa > [η]_CED > [η]_Cadoxen > [η]_Cuoxam; (2) the reported intrinsic viscosities and molecular weights for cellulose are lower than the true value due to degradation of cellulose in the solvents; (3) the rate of degradation was the smallest in LiCl/DMAc and NH₃/NH₄SCN, moderate in cadoexn and FeTNa, and the highest in CED and cuoxam; (4) the plot of log K versus exponent a was linear and inversely related; (5) the curve was used for estimation of the constant K for cellulose in a solvent (NH3/NH4SCN) with a known exponent a; and (6) among various reported solvents, LiCl/DMAc and NH₃/NH₄SCN are advantageous over other solvents because of a complete dissolution of the polymer with a negligible reduction in its intrinsic viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2189–2193, 2002     

New epoxy resins. I. The stability of epoxy–trialkoxyboroxines triaryloxyboroxine system

A polymer with high aromaticity and/or cyclic ring structures chain backbone usually has high heat, thermal, and flame resistance. Two diglycidyl ethers of bisphenols were prepared from 4,4′ isopropylidenediphenol (DGEBA) and 9,9-bis(4-hydroxyphenyl) fluorene (DGEBF) for evaluation. Four boroxines—trimethoxyboroxine (TMB), triethoxyboroxine (TEB), triisopropoxyboroxine (TIPB) and triphenoxyboroxine (TPB)—were used as the curing agents. DGEBA and DGEBF cured with various boroxines indicate that the trend for their respective glass transition temperature (T_g's), degradation temperatures (T_d's), and gel fractions are TMB-cured epoxy ≈ TEB-cured epoxy < TIPB cured epoxy < TPB cured epoxy. The DGEBF system usually has a higher T_g, T_d, gel fraction, oxygen index (OI), and char yield than the related DGEBA system. DGEBF/DGEBA (80/20 mol ratio) shows a synergistic effect in regard to char formation. This effect exists not only in the copolymer system but also in blended homopolymers of the separately cured resins. A modified mechanism for the polymerization of phenyl glycidyl ether (PGE) with TMB has been proposed.     

High-resolution thermogravimetry of liquid crystalline copoly(p-oxybenzoate–ethylene terephthalate–m-oxybenzoate)

Thermotropic liquid crystalline terpolymers consisting of three units of p-oxybenzoate (B), ethylene terephthalate (E), and m-oxybenzoate (M), were investigated through high-resolution thermogravimetry to evaluate their stability and kinetic parameters of thermal degradation in nitrogen and air. Overall activation energy data of the first major decomposition was calculated through three calculating methods. Thermal degradation occurs in three major steps in both nitrogen and air. Three kinds of degradation temperatures (T_d, T_m1, T_m2) are slightly higher and the first maximum weight-loss rates are slightly lower in nitrogen than in air, suggesting a higher thermostability in nitrogen. The thermal degradation temperatures range from 450 to 457°C in nitrogen and 441 to 447°C in air and increase with increasing B-unit content at a fixed M-unit content of 5 mol %. The temperatures at the first maximum weight loss rate range from 452 to 466°C in nitrogen and 444 to 449°C in air and increase slightly with an increase in B-unit content. The first and second maximum weight-loss rates are maintained at almost 9.2–10.8 and 4.0–6.1%/min in nitrogen (11.2–12.0 and 3.9–4.2%/min in air) and vary slightly with copolymer composition. The residues after the first major step of degradation are predicted on the basis of the complete exclusion of ester and ethylene groups and hydrogen atoms and compared with those observed experimentally. The char yields at 500°C in both nitrogen and air are larger than 42.6 wt % and increase with increasing B-unit content. However, the char yields at 800°C in nitrogen and air are different. The activation energy and ln(pre-exponential factor) for the first major decomposition are slightly higher in nitrogen than in air and increase with an increase in B-unit content at a given M-unit content of 5 mol %. There is no regular variation in the decomposition order with the variation of copolymer composition and testing atmosphere. The activation energy, decomposition order, and ln(pre-exponential factor) of the thermal degradation for the terpolymers are located in the ranges of 212–263 kJ mol⁻¹, 2.4–3.5, 33–41 min⁻¹, respectively. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2911–2919, 1999     

Improvement in impact strength of modified cardanol‐bonded cellulose thermoplastic resin by adding modified silicones

The impact strength of cellulose diacetate (CDA) bonded with a modified cardanol (3‐pentadecylphenoxy acetic acid: PAA) was greatly improved up to 9 kJ/m² by adding a relatively small amount of modified silicones while suppressing a decrease in bending strength. In our recent research, this thermoplastic resin (PAA‐bonded CDA) exhibited high rigidity, glass transition temperature, and water resistance. However, its impact strength was insufficient for use in durable products. Therefore, silicones modified with polyether, amino, and epoxy groups were investigated as possible ways to improve the impact strength. The results show that adding polyether‐modified silicone (polyether silicone) with moderate polarity relative to PAA‐bonded CDA resulted in shearing deformation greatly enhances its impact strength while maintaining other properties, including glass transition temperature (T_g), water resistance, and thermoplasticity. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40366.     

High‐resolution thermogravimetry of polyethersulfone chips in four atmospheres

Thermal degradation and kinetics of polyethersulfone (PES) chips were studied in air, nitrogen, helium, and argon from room temperature to 790°C by high‐resolution thermogravimetry (TG) at a variable heating rate in response to changes in the sample's degradation rate. In the four atmospheres, a two‐step degradation process in air, argon, and helium or a three‐step degradation process in nitrogen of the PES were found in this investigation. In particular, the three‐step degradation process in nitrogen of the PES revealed by the high‐resolution TG was hardly ever observed by a traditional TG. The initial thermal degradation temperature of the PES increases with the testing atmosphere in the following order: air < argon < helium < nitrogen but the activation energy of the first major degradation of PES increases in a different order: argon < nitrogen < helium < air. The degradation temperature, the temperature at the maximum weight‐loss rate, the maximum weight‐loss rate [(dα/dT)_m1 and (dα/dT)_m2], char yield at 790°C, and activation energy of the first major degradation process obtained by the high‐resolution TG were compared with those by traditional TG. The PES exhibits the largest (dα/dT)_m1 and the greatest char yield at 790°C in helium but the largest (dα/dT)_m2 and smallest char yield in air. A significant dependency of the thermal decomposition of the polymers on the physicochemical properties (density, thermal conductivity, and oxidative ability) of the testing atmospheres is elaborated for the first time. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3631–3637, 2003