Morphology and mechanical properties of polyamide‐6/K resin blends

Mechanical properties and morphological studies of compatibilized blends of polyamide‐6 (PA‐6)/K resin grafted with maleic anhydride (K‐g‐MAH) and PA‐6/K resin/K‐g‐MAH were investigated as functions of K resin/K‐g‐MAH and dispersed phase K resin concentrations, and all the blends were prepared using twin screw extruder followed by injection molding. Scanning electron microscopy (SEM) were used to assess the fracture surface morphology and the dispersion of the K resin in PA‐6 continuous phase, the results showing extensive deformation in presence of K‐g‐MAH, whereas, uncompatibilized PA‐6/K resin blends show dislodging of K resin domains from the PA‐6 matrix. Dynamic mechanical thermal analysis (DMTA) test reveals the partially miscibility of PA‐6 with K‐g‐MAH, and differential scanning calorimetry (DSC) results further identified that the introduction of K‐g‐MAH greatly improved the miscibility between PA‐6 and K resin. The mechanical properties of PA‐6/K resin blends and K‐g‐MAH were studied through bending, tensile, and impact properties. The Izod notch impact strength of PA‐6/K‐g‐MAH blends increase with the addition of K‐g‐MAH, when the K‐g‐MAH content adds up to 20 wt %, the impact strength is as more than 6.2 times as pure PA‐6, and accompanied with small decrease in the tensile and bending strength less than 12.9% and 17.5%, respectively. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

环氧树脂E-44反应增容尼龙6/废印刷电路板非金属粉复合材料的力学性能和热变形温度研究

用环氧树脂E-44作为反应性的增容剂,采用熔融共混方法制备了尼龙6(PA6)/废印刷电路板非金属粉(N-PCB)复合材料。研究了E-44用量、挤出温度以及N-PCB粉末的粒径大小对PA6/N-PCB复合材料力学性能和热变形温度的影响。对复合材料抽提残留物的红外分析实验结果表明E-44与PA6/N-PCB复合材料中PA6以及N-PCB粉末表面发生了化学键合。添加1.25份E-44的PA6/N-PCB复合材料与纯PA6相比,其拉伸强度、拉伸模量、弯曲强度和弯曲模量最大增幅分别为29%、49%、73%和72%,热变形温度提高了42.8℃,但其韧性降低。与未加增容剂相比,其拉伸强度、弯曲强度和缺口冲击强度最大增幅分别为9%、8%和43%,热变形温度提高了9.3℃。     

Micromechanical processes and failure phenomena in reactively compatibilized blends of polyamide 6 and styrenic polymers. II. Polyamide 6/styrene‐acrylonitrile copolymer blends

This work reports on morphological, mechanical, and micromechanical properties of polyamide 6 (PA 6), a styrene‐acrylonitrile copolymer (SAN), and their blends, which were reactively compatibilized using a styrene‐acrylonitrile maleic anhydride (SANMA) terpolymer. Transmission electron microscopy (TEM) investigations revealed the phase morphology of the blends, which is characterized by inclusions of the minor component in the matrix of the major phase. The blend with 50% PA 6 and 50% SAN depicted a cocontinuous morphology. Using a microtensile device for TEM, the samples were deformed under uniaxial loading in the “dry” state (characterized by a zero water content in the PA 6 phase) and in a “wet” state (with water in the PA 6 phase). Whereas the dry blends behaved brittle, the wet blends showed a larger ductility with the formation of deformation bands in the matrix (PA 6 or SAN), which were initiated by stress concentration at the SAN and PA 6 particles, respectively. In the interface of blends with a PA 6 matrix and SAN inclusions, two phenomena were observed: partial cavitation and debonding on the one hand and partial fibrillation on the other hand. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polystyrene and polyether polyurethane elastomer blends compatibilized by SMA: Morphology and mechanical properties

Blends of polystyrene (PS) and the polyether polyurethane elastomer (PU‐et) were prepared by melt mixing using poly(styrene‐co‐maleic anhydride) (SMA) containing 7 wt % of maleic anhydride as a compatibilizer. The polyurethane in the blends was crosslinked using dicumyl peroxide or sulfur. The content of maleic anhydride was varied in the blends through the addition of different SMA amounts. The morphology of the blends was analyzed by SEM and a drastic reduction of both the domain size and its distribution was observed with increase of the anhydride content in the blends. The morphology of the PU‐et blends also showed dependence on the crosslinker agent used for the elastomer, and larger domains were obtained for the elastomer phase crosslinked with dicumyl peroxide. The mechanical properties of the blends were evaluated by flexural and impact strength tests. The blend containing 0.5 wt % of maleic anhydride and 20 wt % of PU‐et crosslinked with sulfur showed the highest strength impact, which was three times superior to the PS strength impact, and the blends containing 20 wt % of PU‐et crosslinked with dicumyl peroxide showed the highest deflection at break independent of the anhydride content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 830–837, 2002     

Improving transparency of stretched PET/MXD6 blends by modifying PET with isophthalate

Compatibilized blends of PET and MXD6 have good transparency because their refractive indices match closely. However, haziness is observed when the blends are stretched because stretching imparts greater refractive index anisotropy to PET than to MXD6. Analysis of the strain-dependent birefringence reveals that different molecular deformation models describe the intrinsic birefringence of PET and MXD6. This study focuses on reducing the intrinsic birefringence of PET by partially replacing terephthalate with isophthalate. Statistical copolymers are prepared by conventional copolymerization of the monomers. Alternatively, blocky copolymers are obtained by melt blending PET with poly(ethylene isophthalate) (PEI). A close refractive index match with stretched MXD6 is achieved with copolymers containing 15-20% isophthalate. Statistical copolymers in this composition range are not satisfactory for blending because they have low molecular weight and are difficult to stretch. However, blocky copolymers containing 15-20% isophthalate form blends that stretch readily. After biaxial stretching, transparency of blends with 10 wt% MXD6 approaches that of PET. Good transparency of the blends is validated with stretch-blown bottle walls. Oxygen transport measurements confirm that partial replacement of terephthalate with isophthalate does not affect the good gas barrier properties of biaxially stretched PET blends.     

Morphology and mechanical properties of PET/PE blends compatibilized by nanoclays: Effect of thermal stability of nanofiller organic modifier

Poly(ethylene terephtalate)/poly(ethylene) (PET/PE) blends (80/20 wt %) were prepared by melt‐extrusion and compatibilized by addition of nanoclays. Two commercially available organically modified montmorillonites (Cloisite© 10A and 30B) were chosen as reference and a third one was specially organomodified at lab scale with a thermally stable phosphonium surfactant using conventional cationic exchange reaction. The size of the dispersed polymer phase (PE droplets) and the ductility of the blends depend more on the thermal stability of the surfactant of the organomodified clay than on the enthalpic interactions between the blend components and the surfactants used for the modification of the clays. The highest mechanical properties (yield stress and elongation at break) and the better compatibilization efficiency (smallest dispersed PE droplets) were observed in the presence of phosphonium organomodified montmorillonite compared to other less thermally stable commercial organoclays. The analysis of the thermal stability, morphology, and mechanical properties of PET/PE blends containing the surfactants alone in the absence of clay made it possible to evidence separately the effects of the surfactant and of the nanofiller. The role of the surfactant as compatibilization agent was demonstrated. In the absence of nanofiller, the finest morphological and highest ductility were again obtained with the phosphonium surfactant which is the most thermally stable. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

环氧树脂E-44/HDPE-g-MAH增韧聚苯硫醚性能

将马来酸酐接枝高密度聚乙烯( HDPE-g-MAH)与聚苯硫醚(PPS)共混制成共混体系,体系采用环氧树脂E-44增容,考察共混物体系的热行为、力学性能、相形态、增韧机理.结果表明:PPS与HDPE-g-MAH的相容性有所改善,尤其是环氧树脂E-44的加入,使在增强增韧方面效果更加明显,体系的冲击韧性随着环氧树脂E-44含量的增加表现为先增强后降低.当环氧树脂E-44质量分数为6.5％时,共混体系的拉伸强度提高到52 MPa,冲击强度也达到7.5 kJ/m2.PPS/HDPE-g-MAH/E-44共混体系中,环氧树脂E-44作为增客剂和增韧剂提高PPS基体与HDPE-g-MAH的界面粘结能力,使其共混物达到增强增韧的效果.     

Melt rheological properties of reactive compatibilized HDPE/PET blends

Melt rheological properties of high density polyethylene and poly(ethylene terephthalate) (HDPE/PET) blends compatibilized by an ethylene–butyl acrylate–glycidyl methacrylate terpolymer (EBAGMA) were studied by means of a HAAKE torque rheometer and a capillary rheometer. The phase morphology of the blends was evaluated by a scanning electron microscope (SEM). The results showed that the melts of blends behave pseudoplasticity. The addition of EBAGMA strengthens the interfacial adhesion between HDPE and PET and improves the phase dispersion due to reactive compatibilization. It was observed that the balance torque, melt viscosity, and sensitivity of melt viscosity to shear rate of the melts increase with increasing content of EBAGMA, but the melt flow index and activation energy decrease. At the same time, the plasticizing time is shortened indicating that the processability of the compatibilized blends has been improved. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Oxygen permeation through films of compatibilized polypropylene/polyamide 6 blends

Polypropylene/polyamide 6 blends were prepared by melt mixing, without or with the addition of a suitable commercial product, a polypropylene grafted with 1% maleic anhydride, used as an interfacial modifier. The oxygen permeation through their films was studied as a function of temperature and the effect of the presence of the compatibilizer on the barrier properties of the material was examined. In addition, the diffusion coefficients were measured. The relationships between transport parameters and blend morphology were investigated by microscopic observations, together with chemical etchings, and a simple model was applied for interpreting the experimental permeation data. Differential scanning calorimetry was used in the determination of the degree of crystallinity of the blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1941–1949, 1999     

HDPE／PA—6防渗合金的研制及应用

本文介绍了阻隔容器用HDPE/PA-6防渗合金的工艺技术,包括配方选择、相容剂的选择及最佳工艺条件的确定。将制成的改性粒料吹塑成小型中空容器,并进行了二甲苯、汽油防渗试验。     

尼龙-6合金及应用

综述了国外目前已商品化尼龙 6合金的特性及应用,对各种尼龙 6合金的相容剂及正在研究开发的尼龙 6合金作了介绍,简述了国内尼龙 6合金的现状,展望了尼龙 6合金的发展前景     

Morphology of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized by a methyl methacrylate/maleic anhydride copolymer

The morphologies of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized with a methyl methacrylate/maleic anhydride copolymer, with 3–20 wt % maleic anhydride, were examined by transmission electron microscopy. Some staining techniques were employed for identifying the various phases. The binary blends were immiscible and exhibited poor mechanical properties that stemmed from the unfavorable interactions among their molecular segments. This produced an unstable and coarse phase morphology and weak interfaces among the phases in the solid state. The presence of the copolymer in the blends clearly led to a more efficient dispersion of the acrylonitrile–butadiene–styrene phase and consequently optimized Izod impact properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3512–3518, 2003     

An investigation on recycled PET/PP and recycled PET/PP‐EP compatibilized blends: Rheological,morphological, and mechanical properties

The effectiveness of P(E‐co‐MA‐co‐GMA) as a compatibilizer for recycled PET/PP and recycled PET/PP‐EP (polypropylene (ethylene‐propylene) heterophase copolymer) blends was investigated by means of morphological (scanning electron microscopy), rheological (small amplitude oscillatory shear), mechanical (tensile, flexural and impact tests), and thermal (differential scanning calorimetry) properties. Compatibilizer concentration ranged from 1 to 5 wt % with respect to the whole blend. All blends were obtained in a 90/10 composition using a twin screw extruder. Compatibilization effects for PETr/PP‐EP were more pronounced due to ethylene segments present in both PP‐EP and P(E‐co‐EA‐co‐GMA). PETr/PP‐EP has shown greater dispersed phase size reduction, a more solid‐like complex viscosity behavior and larger storage modulus at low frequencies in relation to PETr/PP blend. For both investigated blends, mechanical properties indicated an improvement in both elongation at break and impact strength with increasing compatibilizer content. PETr/PP‐EP blends showed improved performance for the same level of compatibilizer content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41892.     

PA-6/UHMWP/EHDPE-g-MAH共混合金的形态结构与性能的研究

通过SEM观察和机械性能测试,研究了PA 6 UHMWPE HDPE g MAH共混合金的形态结构和性能。结果表明:加入HDPE g MAH可有效地改善共混物的相容性,增强两相界面间的粘结强度,降低分散相尺寸;同时还改善了共混物的机械性能,降低了熔体流动速率,提高了常温和低温冲击强度,降低了吸水率。     

Evaluation of the Effectiveness of New Compatibilizers Based on EBAGMA‐LDPE and EBAGMA‐PET Masterbatches for LDPE/PET Blends

The present paper is aimed to evaluate the efficiency of two masterbatches, i.e., EBAGMA/LDPE (MB1) and EBAGMA/PET (MB2) with 50/50 w/w composition, prepared by melt mixing and used as new compatibilizers for blends of LDPE/PET. The morphology, the mechanical and the thermal properties of LDPE/PET/MB1 and LDPE/PET/MB2 ternary blends have been investigated. Morphological investigation by SEM of LDPE/PET/MB1 ternary blends showed a finer dispersion of PET in LDPE matrix with a better interfacial adhesion compared to those of both LDPE/PET/MB2 and binary LDPE/PET blends. The results also indicated a substantial improvement in both elongation at break and impact strength, while the Young's modulus decreased. Moreover, the thermal properties showed a decrease of the crystallization phenomena of PET in LDPE/PET/MB1 blend, thus confirming the good dispersion of PET particles into the continuous phase of LDPE matrix, leading to the conclusion that MB1 could be an efficient compatibilizer for LDPE/PET system.

     

Effects of compatibilization of oxidized polypropylene on PP blends of PP/PA6 and PP/talc

The influence of compatibilization on the dynamic mechanical properties of polypropylene (PP) binary blends with polyamide‐6 (PA6), Talc, and oxidized PP (OPP) was investigated. The oxidation of PP homopolymer was performed in a internal mixer by using air as a oxidizing agent (under atmospheric pressure) and dodecanol‐1 as an accelerator at 180°C for 6½ h [Abdouss, M.; Sharifi‐Sanjani, N.; Bataille, P. J Appl Polym Sci 1999, 36, 10]. In the blends, OPP was used as a blend component and compared with PP over the whole concentration range. Pressed film blends of PP/OPP, PP/OPP/Talc, and PP/OPP/PA6 were examined by dynamic mechanical analyzer, thermal gravimetry analysis, and scanning electron microscopy. Mechanical properties such as tensile strength, modulus of elasticity, elongation, melt flow index, and hardness of the blends were measured. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2871–2883, 2004     

Morphology and rheology of HDPE/LCP blends compatibilized by a novel PE-g-LCP copolymer

A novel graft copolymer (PE-g-LCP) consisting of polyethylene (PE) backbones and liquid crystalline polymer (LCP) branches was synthesized via reactive blending of an acrylic acid-functionalized PE (Escor 5000 by Exxon) with a semiflexible LCP (SBH 1 : 1 : 2 by Eniricerche S.p.A.). The crude reactive blending product (COP) was shown by investigation of the fractions soluble in boiling toluene and xylene and of the residue to contain unreacted Escor and SBH, together with the graft copolymer forming the interphase. The compatibilizing activity of COP for PE/SBH blends, compared to that of pure Escor, was investigated using two PE grades. The COP addition into 80/20 PE/SBH blends caused a much stronger reduction of the SBH droplet dimensions and morphology stabilization than did that of pure Escor. The rheological behavior of the samples showed that COP leads to a slight increase of interfacial adhesion in the melt as well and that the effect is more pronounced when lower molar mass PE grade is used as the blend matrix. Melt-spinning tests demonstrated that deformation of the SBH droplets into highly oriented fibrils can be obtained for the blends of lower molar mass PE, compatibilized with small amounts of the novel PE-g-SBH copolymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2069–2077, 1999     

Micromechanical processes and failure phenomena in reactively compatibilized blends of polyamide 6 and styrenic polymers. I. Polyamide 6/acrylonitrile– butadiene–styrene copolymer blends

In this work, in situ investigations of the micromechanical properties of reactively compatibilized blends of polyamide 6 (PA6) and an acrylonitrile–butadiene–styrene copolymer (ABS) were performed with transmission electron microscopy. Three PA6/ABS blends were prepared with a disperse morphology (inclusions of PA6 or ABS) and with a cocontinuous structure. The objective of this work was to study the deformation of the inclusions and the interface between the PA6 phase and the ABS phase. Our transmission electron microscopy investigations revealed that the morphology of the blends was strongly influenced by the asymmetric nature of the interface between PA6 and ABS. In the blends with a PA6 matrix, the interface between PA6 and the ABS inclusions was deformed in tensile deformation under uniaxial loading. A strong influence of the PA6 water content on the (micro)mechanical behavior was observed. Although the “dry” blends behaved in a brittle fashion, the “wet” blends behaved in a ductile fashion with the formation of deformation bands in the matrix (PA6 or ABS), which were initiated by stress concentration at the particles (ABS or PA6, respectively). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A study on the effects of SEBS‐g‐MAH on the phase morphology and mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends

In this work, five ternary blends based on 70% by weight (wt %) of polypropylene (PP) with 30% wt of polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene)(SEBS) dispersed phase consists of 15 wt % PC and 15 wt % reactive (maleic anhydride grafted) and nonreactive SEBS mixtures at various ratios were prepared in a co‐rotating twin screw extruder. scanning electron microscopy (SEM) micrographs showed that the blends containing only nonreactive SEBS exhibited a fine dispersion of core‐shell particles. With decreasing the SEBS/SEBS‐g‐Maleic Anhydride (MAH) weight ratio, the morphology changed from the core‐shell particles to a mixed of core‐shell, rod‐like and individual particles. This variation in phase morphology affected the thermal and mechanical properties of the blends. DSC results showed that the blends containing only nonreactive SEBS exhibited a minimum in degree of crystallinity due to the homogeneous nucleation of core‐shell particles. Mechanical testing showed that in the SEBS/SEBS‐g‐MAH weight ratio of 50/50, the modulus and impact strength increased compared with the PP matrix while the yield stress had minimum difference with that of PP matrix. These effects could be attributed to the formation of those especial microstructures revealed by the SEM studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and mechanical properties of polypropylene/high‐impact polystyrene blends from postconsumer plastic waste

The compatibilizing effect of the triblock copolymer poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS) on the morphological and mechanical properties of virgin and recycled polypropylene (PP)/high‐impact polystyrene (HIPS) blends was studied, with the properties optimized for rigid composite films. The components of the blend were obtained from municipal plastic waste, PP being acquired from mineral water bottles (PP_b) and HIPS from disposable cups. These materials were preground, washed only with water, dried with hot air, and ground again (PP_b) or agglutinated (HIPS). Blends with three different weight ratios of PP_b and HIPS (6:1, 6:2, and 6:3) were prepared, and three different concentrations of SEBS (5, 6, and 7 wt %) were used for investigations of its compatibilizing effect. Scanning electron microscopy showed that SEBS reduced the diameter of dispersed HIPS particles in the globular and fibril shapes and improved the adhesion between the disperse phase and the matrix. However, SEBS interactions with PP_b and HIPS influenced the mechanical properties of the compatibilized PP_b/HIPS/SEBS blends. An adequate composition of PP/HIPS, for both virgin and recycled blends, for applications in composite films with characteristics similar to those of synthetic paper was obtained with a minimal amount of SEBS and a maximal HIPS/PP ratio in the range of concentrations studied. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2861–2867, 2003