Epoxy networks toughened by core–Shell particles: Influence of the particle structure and size on the rheological and mechanical properties

The core–shell particles considered were poly(butyl acrylate) core/epoxy groups functionalizing the poly(methyl methacrylate) shell. Physical and thermomechanical properties of benzyl dimethylamine (BDMA)‐catalyzed diglycidyl ether of bisphenol A (DGEBA)/dicyandiamine epoxy networks toughened with core–shell particles were studied. The blends were prepared under well‐defined processing conditions. The resulting properties were found to depend on the state of the dispersion of the particles in the prepolymer matrix before crosslinking. These particles were dispersed at different volume fractions in order to vary the interparticle distance. The relationships between the size of the core–shell particles and the level of toughening are reported. Static mechanical tests were performed in tension and compression modes on these core–shell polyepoxy blends. A slight decrease in the Young's modulus and an increase in the ability to plastic deformation were observed. Using linear fracture mechanics (LEFM), an improvement of the fracture properties (K_IC) was measured. By varying the volume fraction of core–shell particles, an optimum toughness improvement was found for an interparticle distance equal to 400 nm (with an average particle size of 600 nm). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 849–858, 1999     

Core–shell particles to toughen epoxy resins. I. Preparation and characterization of core–shell particles

A two-stage, multistep soapless emulsion polymerization was employed to prepare various sizes of reactive core–shell particles (CSPs) with butyl acrylate (BA) as the core and methyl methacrylate (MMA) copolymerizing with various concentrations of glycidyl methacrylate (GMA) as the shell. Ethylene glycol dimethacrylate (EGDMA) was used to crosslink either the core or shell. The number of epoxy groups in a particle of the prepared CSP measured by chemical titration was close to the calculated value based on the assumption that the added GMA participated in the entire polymerization unless it was higher than 29 mol %. Similar results were also found for their solid-state ^13C-NMR spectroscopy. The MMA/GMA copolymerized and EGDMA-crosslinked shell of the CSP had a maximum glass transition temperature (T_g) of 140°C, which was decreased with the content of GMA at a rate of −1°C/mol %. However, the shell without crosslinking had a maximum T_g of 127°C, which decreased at a rate of −0.83°C/mol %. The T_g of the interphasial region between the core and shell was 65°C, which was invariant with the design variables. The T_g of the BA core was −43°C, but it could be increased to −35°C by crosslinking with EGDMA. The T_g values of the core and shell were also invariant with the size of the CSP. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2069–2078, 1998     

Preparation and characterization of core–shell polystyrene and polymethylsilsesquioxane structure latex particles by seeded polymerization

Composite polystyrene and polymethylsilsesquioxane (PS‐PMSSQ) latices were prepared by hydrolysis and polycondensation of triethoxylmethylsilane (TEOMS) in the presence of PS seed latices, obtained by gamma ray induced polymerization. Morphology of the composite latex particles was observed by transmission electronic microscopy and their size distribution was measured by dynamic laser light scattering. It was found that if 1 wt% silicon‐containing surfactant (SCS) and 0.4 wt% dodecylbenzene sulphonic acid (DBSA) were both used, core–shell/PS‐PMSSQ latex particles could be prepared at 30 °C. The core–shell structure was further characterized by X‐ray photoelectron spectrometry. With 0.5 wt% SCS or 0.2 wt% DBSA, the capsulation was incomplete. At 0 and 90 °C, the PMSSQ phase penetrated into the seed particles. No core–shell structure was observed when DBSA was replaced by hydrochloric acid or SCS was replaced by poly(ethylene glycol) monooctylphenyl ether. Copyright © 2006 Society of Chemical Industry     

Preparation and characterization of core–shell polystyrene–polydimethylsiloxane particles by seeded polymerization

Nanometer scale particles of seed latex were successfully prepared by polymerization induced by gamma rays. By modification of the coupling agent 3‐methacryloxylpropyltrimethoxylsilane (MPS) at the surface of polystyrene (PSt) particles, polydimethylsiloxane (PDMS) was introduced outside the PSt particles and composite latex particles with a core–shell (PSt–PDMS) structure were successfully prepared. Because of the chemical bond linkage between the core and the shell, such a structure is stable. Direct evidence of the core–shell structure was observed by transmission electron microscopy (TEM). In addition the chemical bond linkage was confirmed by Fourier‐transfer infrared (FT‐IR) spectroscopy. An indirect proof of the core–shell structure was given by water absorption ratio determination of the different samples. Copyright © 2004 Society of Chemical Industry     

Hygrothermal aging and fracture behavior of styrene‐acrylonitrile/acrylate based core–shell rubber toughened poly(butylene terephthalate)

A study of hygrothermal aging in terms of the kinetics of moisture absorption by poly(butylene terephthalate) (PBT) and styrene‐acrylonitrile/acrylate based core–shell rubber (CSR) toughened PBT (PBT‐CSR) was undertaken. The diffusion of water into the PBT compounds with various CSR contents was investigated by immersion of specimens in water at temperatures between 30 and 90°C. It was observed that the equilibrium moisture content and the diffusion coefficient of the PBT both increased with increasing CSR content. The fracture behaviors of the PBT and PBT‐CSR were investigated. The focus of investigation was on the effect of an internal parameter (rubber content) and external parameters (testing temperature, deformation rates, and hygrothermal aging) on the fracture behavior of these materials. The fracture response of the various materials was evaluated by the fracture toughness and energy measured on static‐loaded compact tension specimens. The tensile and fracture behavior of PBT and PBT‐CSR was affected by both the internal and external parameters. On its own the CSR impact modifier failed to improve the toughness of PBT at either high testing speed or subambient temperature (−40°C). Based on the dynamic mechanical analysis study, the CSR is believed to behave as a rigid particulate filler in the PBT that consequently reduces the ductility of the PBT. All the materials tested showed poor retention of the tensile and fracture properties upon exposure to hygrothermal aging at 90°C, and these properties could not be restored by subsequent drying. This was attributed to severe hydrolytic degradation of the PBT that caused permanent damage to the materials. The failure modes of PBT and PBT‐CSR were assessed by fractographic studies in a scanning electron microscope. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2470–2481, 1999     

A continuous tubular reactor for core–shell latex particles

High solids content poly(butyl acrylate)/poly(methyl methacrylate) core–shell latex particles were produced using miniemulsion polymerisation in a continuous linear tubular reactor. The resulting products were and shown to be comparable to a batch process. Final solids contents of 41 and 48 wt.% were shown to be possible in a simple tubular reactor. Differential scanning calorimeter analysis indicated that core–shell particles were formed under these conditions. © 2011 Canadian Society for Chemical Engineering     

Surface modification effects of core–shell rubber particles on the toughening of poly(butylene terephthalate)

We toughened poly(butylene terephthalate) (PBT) by loading core–shell rubber (CSR) type impact modifiers, consisting of a rubbery poly(n‐butyl acrylate) core and a rigid poly(methyl methacrylate) shell. To optimize the dispersion of CSR particles into the PBT matrix during melt compounding, the shell surface was modified with different grafting ratios of glycidyl methacrylate (GMA) reactive with PBT chain ends. In PBT blends with a 20 wt % CSR loading, the dispersed rubbery phases showed discernible shapes depending on the grafted GMA content, from predetermined spheres with 0.25 ± 0.05 μm diameters to their aggregates in the 2–3 μm diameter range. As a result, the interparticle spacing (τ) could be controlled from 0.25 to 4.0 μm in the PBT blends containing the fixed rubber loading. The Izod impact strengths of these samples increased significantly below τ = 0.4 μm. Additional thermal and morphological analyses strongly supported the hypothesis that the marked increase in toughness of the blends was related to less ordered lamellar formation of the PBT matrix under the confined geometry. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Surface immobilisation of fluorinated polystyrene‐acrylate latex nanoparticles with core–shell structure by crosslinking

Fluorinated polystyrene‐acrylate (PSA) latex nanoparticles with core–shell structure were synthesised by two‐stage seeded emulsion polymerisation method in the presence of reactive emulsifier DNS‐86. Diallyl phthalate (DAP) and Vinyltriethoxysilicone (VTES) were used as crosslinking agent to immobilise the fluorinated copolymer on the surface of the latex film. Fourier transform infrared spectroscopy (FTIR) spectra show that fluorine and siloxane monomers were effectively involved in the emulsion copolymerisation. Transmission electron microscope (TEM) observation shows that the prepared emulsion particles had a core–shell structure with fluorinated copolymer in the shell. X‐ray photoelectron spectroscopy (XPS) analysis reveals that fluorine atom has the tendency of migrating to the film–air interface and the incorporation of VTES helps the migration of fluorine atom towards the film–air interface. Water contact angle (WCA) test proved that DAP and VTES as crosslinking agent can immobilise the fluorinated copolymer on the surface of the latex films. © 2011 Canadian Society for Chemical Engineering     

聚氨酯丙烯酸酯/环氧丙烯酸酯分散体系的制备

用水性聚氨酯丙烯酸酯改性环氧丙烯酸酯,制备了聚氨酯丙烯酸酯/环氧丙烯酸酯分散体系。随着分散体中聚氨酯丙烯酸酯浓度的增加,体系稳定性增加,当其浓度达到30%时,可制得稳定的分散体系。这种分散体系可作为一种紫外光固化水性涂料,其涂膜的耐磨性、柔韧性都比环氧丙烯酸酯涂膜增强,而硬度变化不大。     

Influence of core–shell rubber particles synthesized with different initiation systems on the impact toughness of modified polystyrene

Core–shell poly(butadiene‐graft‐styrene) (PB‐g‐PS) rubber particles were synthesized with different initiation systems by emulsion grafting polymerization. These initiation systems included the redox initiators and an oil‐soluble initiator, 1,2‐azobisisobutyronitrile (AIBN). Then the PB‐g‐PS impact modifiers were blended with polystyrene (PS) to prepare the PS/PB‐g‐PS blends. In the condition of the same tensile yield strength on both samples, the Izod test showed that the notched impact strength of PS/PB‐g‐PS(AIBN) was 237.8 J/m, almost 7 times than that of the PS/PB‐g‐PS(redox) blend, 37.2 J/m. From transmission electron microscope (TEM) photographs, using the redox initiators, some microphase PS zones existed in the core of PB rubber particles, which is called “internal‐grafting.” This grafting way was inefficient on toughening. However, using AIBN as initiator, a great scale of PS subinclusion was seen within the PB particle core, and this microstructure increased the effective volume fraction of the rubber phase with a result of improving the toughness of modified polystyrene. The dynamic mechanical analysis (DMA) on both samples showed that the glass transition temperature (T_g) of rubber phase of PS/PB‐g‐PS(AIBN) was lower than that of PS/PB‐g‐PS(redox). As a result, the PB‐g‐PS(AIBN) had better toughening efficiency on modified polystyrene than the PB‐g‐PS(redox), which accorded with the Kerner approximate equation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 738–744, 2007     

Effect of acrylic core–shell rubber particles on the particulate flow and toughening of PVC

Different types of acrylic core–shell rubber particles with a poly(butyl acrylate) (PBA) core and a grafted poly(methyl methacrylate) (PMMA) shell were synthesized. The average size of acrylic core–shell latex particles ranged from 100 to 170 nm in diameter, having the core gel content in the range of 35–80%. The melt blending behavior of the poly(vinyl chloride) (PVC) and the acrylic core–shell rubber materials having different average particle sizes and gel contents was investigated in a batch mixing process. Although the torque curves showed that the particulate flow of the PVC in the blends was dominant, some differences were observed when the size and gel content of the particles varied. This behavior can be attributed to differences in the plasticizing effect and dispersion state of various types of core–shell rubber particles, which can vary the gelatin process of the PVC in the mixing tool. On the other hand, the highest toughening efficiency was obtained using core–shell rubber particles with the smallest particle size (i.e., 100 nm). The results showed that increasing the gel content of the core–shell impact modifiers with the same particle size improved the particle dispersion state in the PVC matrix. The toughening efficiency decreased for the blends containing 100 and 170 nm rubber particles as the gel content increased. Nevertheless, unexpected behavior was observed for the blends containing 140 nm rubber particles. It was found that a high level of toughness could be achieved if the acrylic core–shell rubber particles as small as 100 nm had a lower gel content. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of core–shell glass bead/polysulfone microspheres with two‐step sol–gel process

Core–shell microspheres made from glass beads as the core phase and polysulfone (PSf) as the shell phase can act as an absorbent in the separation process or a supporter for chemical reactions. Based on phase‐inversion principles, a two‐step sol–gel method was developed in this work in which ether was added first and H₂O was added second to a PSf‐containing dimethyformamide (DMF) solution to help PSf solidify on the surface of glass beads. The results from scanning electron microscopy, Fourier transform IR, and X‐ray photoelectron spectroscopy showed that a dense layer of PSf (thin to several microns) was coated on the glass beads and the core–shell microspheres were almost monodispersed. The utilization percentages of the glass beads and PSf were high as 100 and 80%, respectively. The thickness of the PSf membrane was calculated to be about 4.3 μm. To obtain well‐monodispersed microspheres, the practical volume ratio of ether to DMF was recommended to be larger than 4.5. The results suggested that the two‐step sol–gel method is a highly efficient process for preparation of glass bead/PSf core–shell microspheres. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3365–3369, 2006     

Preparation of core–shell particles by dispersion polymerization with a poly(ethylene oxide) macroazoinitiator

A macroazoinitiator (MAI) containing a poly(ethylene oxide) (PEO) block was used with a methyl methacrylate monomer to prepare polymer particles in ethanol/H₂O solutions. The effects of the monomer/MAI ratio (RMI) and H₂O content in the solutions on the molecular weight, particle diameters, and chemical structure of the resulting polymer particles were investigated. The reaction mixtures showed three kinds of states, which were milky colloid solutions, macrogels and/or precipitations, and clear solutions. The colloid solutions were obtained in the solutions with an H₂O content of about 50–90 vol % and a RMI of 20–400. In the colloid solutions, core–shell nanospheres consisting of PEO shells and poly(methyl methacrylate) (PMMA) cores were predominantly obtained. In the specific conditions close to the area of gel and/or precipitation formation, particles connected about 0.5–5 μm in length were obtained. Multiblock copolymers nanospheres tended to be obtained with lower RMIs, and PMMA‐PEO‐PMMA tri‐bloc and/or PMMA‐PEO di‐block copolymer nanospheres were obtained with higher RMIs. The solubility of the monomer and the generated polymer in solutions may have affected the polymerization development and the state of the products. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of core–shell nanosilica/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) latex

A core–shell nanosilica (nano‐SiO₂)/fluorinated acrylic copolymer latex, where nano‐SiO₂ served as the core and a copolymer of butyl acrylate, methyl methacrylate, and 2,2,2‐trifluoroethyl methacrylate (TFEMA) served as the shell, was synthesized in this study by seed emulsion polymerization. The compatibility between the core and shell was enhanced by the introduction of vinyl trimethoxysilane on the surface of nano‐SiO₂. The morphology and particle size of the nano‐SiO₂/poly(methyl methacrylate–butyl acrylate–2,2,2‐trifluoroethyl methacrylate) [P(MMA–BA–TFEMA)] core–shell latex were characterized by transmission electron microscopy. The properties and surface energy of films formed by the nano‐SiO₂/P(MMA–BA–TFEMA) latex were analyzed by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy/energy‐dispersive X‐ray spectroscopy, and static contact angle measurement. The analyzed results indicate that the nano‐SiO₂/P(MMA–BA–TFEMA) latex presented uniform spherical core–shell particles about 45 nm in diameter. Favorable characteristics in the latex film and the lowest surface energy were obtained with 30 wt % TFEMA; this was due to the optimal migration of fluorine to the surface during film formation. The mechanical properties of the films were significantly improved by 1.0–1.5 wt % modified nano‐SiO₂. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of epoxy resin on the properties of maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer toughened polyamide 6 blends

Maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer (ABS‐g‐MA) was used as an impact modifier of polyamide 6 (PA6). Epoxy resin was introduced into PA6/ABS‐g‐MA blends to further improve their properties. Notched Izod impact tests showed that the impact strength of PA6/ABS‐g‐MA could be improved from 253 to 800 J/m with the addition of epoxy resin when the ABS‐g‐MA content was set at 25 wt %. Differential scanning calorimetry results showed that the addition of epoxy resin made the crystallization temperature and melting temperature shift to lower temperatures; this indicated the decrease in the PA6 crystallization ability. Dynamic mechanical analysis testing showed that the addition of epoxy resin induced the glass‐transition temperature of PA6 and the styrene‐co‐acrylonitrile copolymer phase to shift to higher temperatures due to the chemical reactions between PA6, ABS‐g‐MA, and epoxy resin. The scanning electron microscopy results indicated that the ABS‐g‐MA copolymer dispersed into the PA6 matrix uniformly and that the phase morphology of the PA6/ABS‐g‐MA blends did not change with the addition of the epoxy resin. Transmission electron microscopy showed that the epoxy resin did not change the deformation mechanisms of the PA6/ABS‐g‐MA blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Emulsion polymerization of styrene and DEAEMA with a core–shell structure

Polystyrene–poly(N,N‐diethylamino ethyl methacrylate) (PS–PDEAEMA) particles with a core–shell morphology were prepared by seeded emulsion polymerization. Poly(oxyethylene) (POE) (n = 15 and 30) nonyl phenol and sodium lauryl sulfate (SLS) were used as emulsifiers. These two emulsifiers were selected in order to study the effect of nonionic and ionic emulsifiers on the reaction because of the basic character of DEAEMA. The core–shell morphology was investigated independently in the presence of water‐soluble potassium persulfate (KPS) and of oil‐soluble azobisisobutyronitrile (AIBN). The morphologic structure of the particles was studied using scanning electron microscopy and transmission electron microscopy. The latex particles and the polymers were characterized by differential scanning analysis, thermogravimetric analysis, and gel permeation chromatography. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1977–1985, 2000     

Core–shell latex containing fluorinated polymer rich in shell

Core–shell latex with polyacrylate rich in core and fluoropolymer rich in shell was prepared by semicontinuous emulsion polymerization in the presence of mixed emulsifiers. The solids content of the latex was about 25 wt %. The polymerization conditions for the latex were discussed. The morphology of latex particles was characterized by transmission electron microscopy and the surface properties were determined by the Wilhelmy method. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1147–1153, 2002     

Characterization of stabilized porous magnetite core–shell nanogel composites based on crosslinked acrylamide/sodium acrylate copolymers

Stabilized and dispersed superparamagnetic porous nanogels based on sodium acrylate (AA‐Na) and acrylamide (AM) in a surfactant‐free aqueous system were synthesized via solution polymerization at room temperature. The formation of magnetite nanoparticles was confirmed and their properties characterized using Fourier transform infrared spectroscopy. Extensive characterization of the magnetic polymer particles using transmission electron microscopy (TEM), dynamic light scattering and zeta potential measurements revealed that Fe₃O₄ nanoparticles were incorporated into the shells of poly(AM/AA‐Na). The average particle size was 5–8 nm as determined from TEM. AM/AA‐Na nanoparticles with a diameter of about 11 nm were effectively assembled onto the negatively charged surface of the as‐synthesized Fe₃O₄ nanoparticles via electrostatic interaction. Crosslinked magnetite nanocomposites were prepared by in situ development of surface‐modified magnetite nanoparticles in an AM/AA‐Na hydrogel. Scanning electron microscopy was used to study the surface morphology of the prepared composites. The morphology, phase composition and crystallinity of the prepared nanocomposites were characterized. Atomic force microscopy and argon adsorption–desorption measurements of Fe₃O₄.AM/AA indicated that the architecture of the polymer network can be a hollow porous sphere or a solid phase, depending on the AA‐Na content. © 2013 Society of Chemical Industry     

Synthesis and characterization of urethane/acrylate composite latex

Polyurethane dispersion and urethane/acrylate composite latex were synthesized and characterized by using a particle size analyzer, gel permeation chromatograph (GPC), Fourier transform infrared spectroscopy coupled with attenuated total reflectance (FTIR‐ATR), dynamic mechanical analysis (DMA), and instron test machine. The amount of solvent and dimethylolpropionic acid (DMPA) used during synthesis of polyurethane resin straightway affected the average particle size and stability of aqueous polyurethane dispersion. The particle size of polyurethane dispersion had nothing to do with that of composite latex. FTIR‐ATR analyses displayed both air‐facing and substrate‐facing surfaces, containing more polyurethane component than the average composition. Some crosslinking reactions occurred in preparing urethane/acrylic composite latex, as indicated by FTIR analyses and solvent extraction. DMA demonstrated three glass transitions for the film from composite latex. Instron tests exhibited better film performance properties for the composite latex than for the corresponding blend latex. A possible particle growth mechanism for preparing urethane/acrylate composite latex was proposed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1620–1628, 2002; DOI 10.1002/app.10526     

Preparation of core–shell latex for the pigmented ink of textile inkjet printing

A core–shell latex comprising poly(butyl acrylate) as core and poly(styrene‐methyl methacrylate) as shell was synthesized by emulsion polymerization using allyloxy nonylphenoxy propanol polyoxyethylene ether ammonium sulfonate (ANPS) as emulsifier. Transmission electron microscope, differential scanning calorimeter, and thermogravimetric analyses suggested the prepared latex had a core–shell structure. The particle size of the core–shell latex was about 102.8 nm with a molar ratio of butylacrylate, methyl methacrylate, and styrene at 6 : 2 : 2, a mass ratio of ANPS and monomers, ammonium persulfate and monomers at 15% and 1.0%, respectively. The core–shell latex showed high centrifugal stability and excellent freeze‐thaw stability. The clogging nozzle rate of the pigmented ink containing 20 wt % core–shell latex was small, whereas the printed fabrics with this pigmented ink exhibited high rub and washing fastness. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013