Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.     

异端基遥爪聚乙二醇的合成

采用3种新式引发剂,即2-(苄氧基）乙醇钾、2-(四氢-2H-吡喃-2-氧基)乙醇钾、单丙烯基乙二醇钾引发环氧乙烷阴离子开环聚合,反应条件为25 ℃、48 h、醇与萘钾摩尔比例1∶1,得到3种异端基遥爪聚乙二醇。以2-(苄氧基）乙醇钾引发聚合所得产物为起始物,经一系列反应,得到两种两端均为活性基团的异端基遥爪聚乙二醇,这种方法具有普适性。通过1HNMR及GPC手段,表征了产物的结构、分子量及分子量分布。结果表明可以得到高产率、分子量可控且分布窄的异端基遥爪聚乙二醇。     

Properties of Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline Conductive Films: The Effect of Poly(ethylene glycol) Diglycidyl Ether

The effect of polyaniline and poly(ethylene glycol) diglycidyl ether on tensile properties, morphology, thermal degradation, and electrical conductivity of poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films was studied. The poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films were prepared using a solution casting technique at room temperature until a homogeneous solution was produced. Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline/poly(ethylene glycol) diglycidyl ether conductive films exhibit higher electrical properties, tensile strength, modulus of elasticity but lower final decomposition temperature than poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films. Scanning electron microscopy morphology showed that the polyaniline more widely dispersed in the poly(vinyl chloride)/poly(ethylene oxide) blends with the addition of poly(ethylene glycol) diglycidyl ether as surface modifier.     

Preparation of physical gel consisting of syndiotactic polystyrene and poly(ethylene glycol)

Syndiotactic polystyrene (s-PS) was blended with poly(ethylene glycol) (PEG) in 1,2-dichloroethane (DCE) solvent. The mixture became a homogeneous solution at 155 °C depending on the composition ratio of PEG to DCE. When the solution was cooled at the rate of 5 °C/min to room temperature, a thermoreversible gelation was occurred. Wide angle X-ray diffraction (WAXD) measurements revealed that the polymer chain of s-PS in the obtained gel was crystallized with a helical conformation, while that in the non-gelated sample was done with an all-trans planar zigzag conformation.After drying gelated samples at 70 °C for 24 h, a novel polymer blend type of the physical gel consisting of s-PS and PEG was obtained. Dynamic mechanical analysis (DMA) revealed that the physical gel had a high modulus and a long elastic plateau in the temperature range of −80-270 °C.     

Miscibility of dextran and poly(ethylene glycol) in dilute aqueous solutions. II. Effect of temperature and composition

The miscibility of dextran (Dx) with poly(ethylene glycol) (PEG) was investigated in dilute aqueous solutions by viscometry. Homopolymers of Dx and PEG and their blends with Dx/PEG ratios of 10/90, 25/75, 50/50, 75/25, and 90/10 were studied at 25, 30, 35, 40, and 45°C in bidistilled and deionized water. Starting with the classical Huggins equation, the results of the viscosity behavior of each parent polymer and their blends were interpreted in terms of miscibility parameters, Δk, Δb, α, β, ΔB, and μ. On the basis of the sign convention involved in these criteria, miscibility between Dx and PEG was found to increase with the weight fraction of PEG in the blend composition and temperature. The fourier transform infrared (FTIR) analysis is also used to investigate the miscibility of the polymer pairs. The existence of specific interactions between Dx and PEG was demonstrated by FTIR spectroscopy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4587–4594, 2006     

Surface modification of poly(ethylene terephthalate) film by coating with poly(ethylene glycol)‐grafted polystyrene

The poly(ethylene glycol) (PEG)‐grafted styrene (St) copolymer, which was formed as a nanosphere, was used as an agent to modify the surface of poly(ethylene terephthalate) (PET) film. The graft copolymer was dissolved into chloroform and coated onto the PET film by dip–coating method. The coated amount depends on the content ratios of PEG and St, the solution concentration, and the coating cycles. The graft copolymers having a low molecular weight of PEG‐ or St‐rich content was fairly stable on washing in sodium dodecyl sulfate (SDS) aqueous solution. It was confirmed that the PET surface easily altered its surface property by the coating of the graft copolymers. The contact angles of the films coated with the graft copolymers were very high (ca. 105–120°). The coated film has good antistatic electric property, which agreed with PEG content. The best condition of coating is a one‐cycle coating of 1% (w/v) graft copolymer solution. The coated surface had water‐repellency and antistatic electric property at the same time. The graft copolymer consisted of a PEG macromonomer; St was successfully coated onto PET surfaces, and the desirable properties of both of PEG macromonomer and PSt were exhibited as a novel function of the coated PE film. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1524–1530, 1999     

聚乙二醇/聚己内酯三嵌段共聚物的合成与表征

以甲苯二异氰酸酯 (TDI)为偶联剂 ,合成了聚乙二醇 (PEG) /聚己内酯 (PCL)两亲性三嵌段共聚物 (PEG-b-PCL -b -PEG ,PECL) ,采用IR、1 H-NMR、DSC和WAXD分析和研究了PECL的结构与性能。实验结果表明 ,PECL的结构和组成与设计相一致 ,结晶度和熔点均低于均聚物 ,且随着PECL中PCL嵌段含量的增加 ,PCL嵌段熔点升高。透射电镜照片显示PECL纳米粒呈核 /壳结构的球形。     

阴离子表面活性剂对聚乙二醇水溶液粘度的影响

测定了聚乙二醇（PEG）在十二烷基硫酸钠（SDS）和琥珀酸双-2-乙己酯磺酸钠（AOT）水溶液中的粘度,讨论了SDS和AOT在水溶液中聚集形态的差异对PEG与SDS和AOT相互作用的不同影响,结果表明：PEG-SDS与PEG-AOT体系粘度均明显增加,而PEG-SDS与PEG-AOT体系粘度变化机制不同,根本原因是表面活性剂在高分子溶液中聚集行为不同,SDS分子在PEG链上聚集,形成类胶束,使高分子链带电,表现出聚电解质的粘度行为;PEG链吸附于AOT囊泡,不同PEG链对囊泡的吸附可能造成高分子链更加伸展,PEG特性粘数增大,使溶液粘度上升。     

Miscibility and crystallization of poly(ethylene oxide) and poly(ε-caprolactone) blends

Blends of poly(ethylene oxide) (PEO) with poly(ε-caprolactone) (PCL), both semicrystalline polymers, were prepared by co-dissolving the two polyesters in chloroform and casting the mixture. Phase contrast microscopy was used to probe the miscibility of PEOB/PCL blends. Experimental results indicated that PEO was immiscible with PCL because the melt was biphasic. Crystallization of PEO/PCL blends was studied by differential scanning calorimetry and analyzed by the Avrami equation. The crystallization rate of PEO decreased with the increase of PCL in the blends while the crystallization mechanism did not change. In the case of the isothermal crystallization of PCL, the crystallization mechanism did not change, and the change in the crystallization rate was not very big, or almost constant with the addition of PEO, compared with the change of the crystallization rate of PEO.     

Biodegradable polymer blends of poly(lactic acid) and poly(ethylene glycol)

Poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) were melt-blended and extruded into films in the PLA/PEG ratios of 100/0, 90/10, 70/30, 50/50, and 30/70. It was concluded from the differential scanning calorimetry and dynamic mechanical analysis results that PLA/PEG blends range from miscible to partially miscible, depending on the concentration. Below 50% PEG content the PEG plasticized the PLA, yielding higher elongations and lower modulus values. Above 50% PEG content the blend morphology was driven by the increasing crystallinity of PEG, resulting in an increase in modulus and a corresponding decrease in elongation at break. The tensile strength was found to decrease in a linear fashion with increasing PEG content. Results obtained from enzymatic degradation show that the weight loss for all of the blends was significantly greater than that for the pure PLA. When the PEG content was 30% or lower, weight loss was found to be primarily due to enzymatic degradation of the PLA. Above 30% PEG content, the weight loss was found to be mainly due to the dissolution of PEG. During hydrolytic degradation, for PLA/PEG blends up to 30% PEG, weight loss occurs as a combination of degradation of PLA and dissolution of PEG. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1495–1505, 1997     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Controlled release of fluorouracil (5-FU) from chitosan-co-poly(ethylene glycol)/ poly(glycerol sebacate)-co-poly(ethylene glycol)-coated iron oxide

A blend of polyglycerol sebacate-poly ethylene glygol/chitosan-poly ethylene glycol-coated iron oxide (PGS-PEG/CS-PEG@Fe₃O₄) nanoparticles for 5FU delivery was prepared by reverse ultrasonic emulsification method. To enhance polymers’ solubility, PEG was grafted. Chemical characterization was performed through Fourier transformed infrared and proton nuclear magnetic resonance spectra. In vitro assay revealed that release profile of 5FU-loaded PGS-PEG/CS-PEG@Fe₃O₄ is sustained. Moreover, cytotoxicity was analyzed on HT29 cell line at the presence of external magnetic field using the lactate dehydrogenase and Alamar Blue. Results illustrate that (PGS-PEG/CS-PEG@Fe₃O₄) is promising to use as a carrier for 5FU anticancer agent with sustained tailored release.     

Ultraviolet-induced crosslinking of solid poly(ethylene oxide)

Poly(ethylene oxide) (PEO) of molecular weight from 200,000 to 2,000,000 was crosslinked by exposure to ultraviolet radiation with a high-pressure 150 W mercury lamp. Photochemical crosslinking of PEO proceeds in the presence of photoinitiators such as benzophenone and acetophenone which act as a hydrogen-abstracting agent. Gel fraction yield exceeds 90%, and the number-average molecular weight between crosslinks determined by equilibrium swelling in chloroform varies from 3,000 to 100,000. The degree of crosslinking can be controlled by changing the irradiation temperature. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2299–2307, 1997     

Miscibility and crystallization in crystalline/crystalline blends of poly(butylene succinate)/poly(ethylene oxide)

Miscibility and crystallization behavior have been investigated in blends of poly(butylene succinate) (PBSU) and poly(ethylene oxide) (PEO), both semicrystalline polymers, by differential scanning calorimetry and optical microscopy. Experimental results indicate that PBSU is miscible with PEO as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer-polymer interaction parameter, obtained from the melting depression of the high-T_m component PBSU using the Flory-Huggins equation, is composition dependent, and its value is always negative. This indicates that PBSU/PEO blends are thermodynamically miscible in the melt. The morphological study of the isothermal crystallization at 95 °C (where only PBSU crystallized) showed the similar crystallization behavior as in amorphous/crystalline blends. Much more attention has been paid to the crystallization and morphology of the low-T_m component PEO, which was studied through both one-step and two-step crystallization. It was found that the crystallization of PEO was affected clearly by the presence of the crystals of PBSU formed through different crystallization processes. The two components crystallized sequentially not simultaneously when the blends were quenched from the melt directly to 50 °C (one-step crystallization), and the PEO spherulites crystallized within the matrix of the crystals of the preexisted PBSU phase. Crystallization at 95 °C followed by quenching to 50 °C (two-step crystallization) also showed the similar crystallization behavior as in one-step crystallization. However, the radial growth rate of the PEO spherulites was reduced significantly in two-step crystallization than in one-step crystallization.     

Biodegradable polymer blends of poly(3-hydroxybutyrate) and poly(DL-lactide)-co-poly(ethylene glycol)

The melting and crystallization behavior and phase morphology of poly(3-hydroxybutyrate) (PHB) and poly(DL-lactide)-co-poly(ethylene glycol) (PELA) blends were studied by DSC, SEM, and polarizing optical microscopy. The melting temperatures of PHB in the blends showed a slight shift, and the melting enthalpy of the blends decreased linearly with the increase of PELA content. The glass transition temperatures of PHB/PELA (60/40), (40/60), and (20/80) blends were found at about 30°C, close to that of the pure PELA component, during DSC heating runs for the original samples and samples after cooling from the melt at a rate of 20°C/min. After a DSC cooling run at a rate of 100°C/min, the blends showed glass transitions in the range of 10–30°C. Uniform distribution of two phases in the blends was observed by SEM. The crystallization of PHB in the blends from both the melt and the glassy state was affected by the PELA component. When crystallized from the melt during the DSC nonisothermal crystallization run at a rate of 20°C/min, the temperatures of crystallization decreased with the increase of PELA content. Compared with pure PHB, the cold crystallization peaks of PHB in the blends shifted to higher temperatures. Well-defined spherulites of PHB were found in both pure PHB and the blends with PHB content of 80 or 60%. The growth of spherulites of PHB in the blends was affected significantly by 60% PELA content. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1849–1856, 1997     

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide) and poly(propylene oxide)

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide (PEO) and poly(propylene oxide) (PPO) was evaluated by building up temperature-concentration phase diagrams. We have studied bifunctional triblock copolymers (HO-PEO-PPO-PEO-OH) and monofunctional diblock copolymers (R-PEO-PPO-OH and R-PPO-PEO-OH, where R length is linear C₄ and C_12–14). The cloud points of the polymer solutions depended on EO/PO ratio, polarity, R length and position of the hydrophilic and hydrophobic segments along the molecule. Such factors influence on the solutions behavior was also analyzed in terms of critical micelle concentration (CMC), which was obtained from surface tension vs. concentration plots. Salts (NaCl and KCl) added into the polymer solutions change the solvent polarity decreasing the cloud points. On the other hand, the cloud points of the polymer solutions increased as a hydrotrope (sodium p-toluenesulfonate) was added. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1767–1772, 1997     

Crystallization and phase separation in blends of high stereoregular poly(lactide) with poly(ethylene glycol)

The effect of cooling rate on crystallization and subsequent aging of high stereoregular poly(lactide) (PLA) blended with poly(ethylene glycol) (PEG) was studied by thermal analysis and by direct observation of the solid state structure with atomic force microscopy (AFM). Blending with PEG accelerated crystallization of PLA. When a PLA/PEG 70/30 (wt/wt) blend was slowly cooled from the melt, PLA crystallized first as large spherulites followed by crystallization of PEG. The extent of PLA crystallization depended on the cooling rate, however, for a given blend composition the PEG crystallinity was proportional to PLA crystallinity. The partially crystallized blend obtained with a cooling rate of 30 °C min⁻¹ consisted of large spherulites dispersed in a homogeneous matrix. The blend was not stable at ambient temperature. With time, epitaxial crystallization of PEG on the edges of the spherulites depleted the surrounding region of PEG, which created a vitrified region surrounding the spherulites. Further from the spherulites, the homogeneous amorphous phase underwent phase separation with formation of a more rigid PLA-rich phase and a less-rigid PEG-rich phase. Decreasing the amount of PEG in the blend decreased the crystallization rate of PLA and increased the nucleation density. The amount of PLA crystallinity did not depend on blend composition, however, PEG crystallinity decreased to the extent that PEG did not crystallize in a PLA/PEG 90/10 (wt/wt) blend.     

Improved processability and performance of biomedical devices with poly(lactic acid)/poly(ethylene glycol) blends

To improve the processability of micropolymer‐based devices used for biomedical applications, poly(lactic acid) (PLA) was melt‐blended with poly(ethylene glycol)s (PEGs) of different molecular weights (MWs; weight‐average MWs = 200, 800, 2000, and 4000; these PEGS are referred to as PEG200, PEG800, PEG2000, and PEG4000, respectively, in this article). The thermal properties, mechanical properties, and rheological properties of the PLA and the PLA–PEG blends were investigated. The tensile samples’ morphologies showed that the low‐MW PEGs filled molds well. The rheological properties confirmed that the low‐MW PEGs decreased the complex viscosity, and improved the processability. With decreasing PEG MW, the PLA glass‐transition temperature decreased. The nanoindenter data show that the addition of PEG decreased the modulus and hardness of PLA. The morphologies of the tensile samples showed that with increasing PEG MW, the thicknesses of the core layers increased gradually. The elongation at break was improved by approximately 247% with the addition of PEG200. Such methods can produce easily processed biological materials for producing biomedical products. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45194.     

Glycerol-modified poly(vinyl alcohol)/poly(ethylene glycol) self-healing hydrogel for artificial cartilage

Poly(vinyl alcohol) (PVA) hydrogels have shown potential applications in bionic articular cartilage due to their tissue-like viscoelasticity, good biocompatibility and low friction. However, their lack of adequate mechanical properties is a key obstacle for PVA hydrogels to replace natural cartilage. In this study, poly(ethylene glycol) (PEG) and glycerol were introduced into PVA, and a PVA/PEG–glycerol composite hydrogel was synthesized using a mixing physical crosslinking method. The mechanical properties, hydrophilicity and tribological behavior of the PVA/PEG–glycerol hydrogel were investigated by changing the concentration of glycerol in PEG. The results showed that the tensile strength of the hydrogel reached 26.6 MPa at 270% elongation at break with 20 wt% of glycerol plasticizer, which satisfied the demand of natural cartilage. In addition, the excellent hydrophilicity of glycerol provides good lubricating properties for the composite gel under dry friction. Meanwhile, self-healing and cellular immunity assays demonstrated that the composite gel could have good self-healing ability and excellent biocompatibility even in the absence of external stimuli. This study provides a new candidate material for the design of articular cartilage, which has the potential to facilitate advances in artificial joint cartilage repair. © 2022 Society of Industrial Chemistry.     

Associative properties of perfluorooctyl end‐functionalized polystyrene–poly(ethylene oxide) diblock copolymers

The synthesis of 2,2,3,3‐tetrahydro‐perfluoroundecanoyl end‐functionalized polystyrene–poly(ethylene oxide) block (PS‐block‐PEO‐R_F) copolymers and their matching PS‐block‐PEO diblock copolymers was carried out by sequential anionic polymerization. Viscometry and ¹⁹F NMR studies show that the PS‐block‐PEO copolymers, in contrast to their matching PS‐block‐PEO‐R_F copolymers, exhibit a micellar rather than the associative behavior seen for the latter. However, the presence of an excess of fluorinated acid, used for end‐functionalization, produces a reduction of the associative behavior above the overlap concentration, with the fluorinated acid acting like a surfactant. A competition may also occur between PS—and R_F—mediated micellization. Copyright © 2004 Society of Chemical Industry