Miscibility between natural rubber and tackifiers. I. Phase diagrams of the blends of natural rubber with rosin and terpene resins

Natural rubber (NR) was blended in various ratios with 17 kinds of tackifiers, which were prepared from rosin and terpenes. The blends were heated to various temperatures (20–120°C) in order to investigate their miscibility. The blends were visually observed for transparency or opacity at each temperature and further observed under an optical microscope for any existence of phase-separated structure. Miscibility of the blends is illustrated as phase diagrams in this article. Phase diagrams of all blends investigated in this study were classified into four types: completely miscible, lower critical solution temperature, upper critical solution temperature, and completely immiscible. The miscible range of a blend system tends to become smaller as the molecular weight of a tackifier increases. The data also indicate that the esters of hydrogenated rosin and of disproportionated rosin show comparatively good miscibility with NR whereas polymerized rosin and its esters have poor compatibility with NR in most cases. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2191–2197, 1997     

Effects of miscibility on probe tack of natural-rubber-based pressure-sensitive adhesives

Natural rubber (NR) was blended in various ratios with 29 kinds of tackifier resins, which were prepared from rosin, terpenes, and petroleum. Miscibilities of all the blend systems were illustrated as phase diagrams in our previous articles. From these blend systems, we selected 7 systems having typical phase diagrams [completely miscible, completely immiscible, and lower critical solution temperature (LCST) types] and carried out measurements of probe tack. Probe tack values were measured at various rates of separation and temperatures to obtain master curves. In the case of miscible pressure sensitive adhesives (PSAs) at the condition of measurement, the peak position in the master curve of probe tack shifted to the lower velocity (higher temperature) as the tackifier content increased. On the contrary, immiscible PSAs had much smaller probe tack values than miscible ones and did not give manifest shift of peaks. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 771–776, 1998     

Rheological behavior of reactive blending of epoxidized natural rubber with cassava starch and epoxidized natural rubber with natural rubber and cassava starch

Epoxidized natural rubbers (ENR‐25 and ENR‐45) were prepared using the performic epoxidation method. Two‐component (ENR–cassava starch) and three‐component (ENR–NR–cassava starch) blends were prepared. ENR‐25 and ENR‐45 were blended with various quantities of gelatinized cassava starch in the latex state. The pure ENR exhibited lower shear stress and shear viscosity than those of the blends with cassava starch. Furthermore, the shear stress and shear viscosity were increased with an increase in the cassava starch concentration. The chemical interaction between the epoxide groups in the ENR and the hydroxyl groups in the cassava starch molecules might be the reason for the increasing trends of the shear stress and shear viscosity. The blends are classified as compatible blends because of the strong chemical bonding between different phases. SEM micrographs were used to clarify the compatibility. Power law behavior with pluglike flow profiles was observed for all sets of ENR–NR–cassava starch blends. Very low power law index values (<0.34) and highly pseudoplastic fluid behavior were also observed. The log additive rule was applied to plots of zero shear viscosity (consistency index) and the shear viscosity versus the concentration of ENR‐25. Positive deviation blending was observed, which indicates compatible blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1752–1762, 2004     

Novel ternary blends of natural rubber/linear low-density polyethylene/thermoplastic starch: influence of epoxide level of epoxidized natural rubber on blend properties

Novel degradable materials based on ternary blends of natural rubber (NR)/linear low-density polyethylene (LLDPE)/thermoplastic starch (TPS) were prepared via simple blending technique using three different types of natural rubber (i.e., unmodified natural rubber (RSS#3) and ENR with 25 and 50 mol% epoxide). The evolution of co-continuous phase morphology was first clarified for 50/50: NR/LLDPE blend. Then, 10 wt% of TPS was added to form 50/40/10: NR/LLDPE/TPS ternary blend, where TPS was the particulate dispersed phase in the NR/LLDPE matrix. The smallest TPS particles were observed in the ENR-50/LLDPE blend. This might be attributed to the chemical interactions of polar functional groups in ENR and TPS that enhanced their interfacial adhesion. We found that ternary blend of ENR-50/LLDPE/TPS exhibited higher 100 % modulus, tensile strength, hardness, storage modulus, complex viscosity and thermal properties compared with those of ENR-25/LLDPE/TPS and RSS#3/LLDPE/TPS ternary blends. Furthermore, lower melting temperature (T _m) and heat of crystallization of LLDPE (?H) were observed in ternary blend of ENR-50/LLDPE/TPS compared to the other ternary blends. Also, neat TPS exhibited the fastest biodegradation by weight loss during burial in soil for 2 or 6 months, while the ternary blends of NR/LLDPE/TPS exhibited higher weight loss compared to the neat NR and LLDPE. The lower weight loss of the ternary blends with ENR was likely due to the stronger chemical interfacial interactions. This proved that the blend with ENR had lower biodegradability than the blend with unmodified NR.     

Distribution of carbon black in natural rubber/acrylic rubber blends

Distributions of carbon black in 30/70% (w/w) natural rubber (NR)/acrylic rubber (ACM) blends were investigated as a function of the carbon black content and type using a dynamic mechanical thermal analysis (DMTA) technique. Two different types of carbon black (N220 and N330) were used, and 10–50 phr carbon black was compounded to the rubber blends. From the DMTA thermograms of various blends, the weight fractions of carbon black in the NR and ACM phases were calculated. Carbon black was unevenly distributed in the rubber blend. It preferred to migrate into the NR phase, regardless of the amount of carbon black that was used. By increasing the carbon black content, the weight fraction of carbon black in the NR phase decreased whereas that in the ACM phase increased. A change in the type of carbon black from N220 to N330 significantly decreased the weight fraction of carbon black in the NR phase, but it was not sufficiently strong to affect the tensile properties and hardness of the rubber blend. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:248–256, 2006     

Rheological properties of recycled chlorinated polyethylene/natural rubber blends vulcanized by sulfur

Blends of elastomeric chlorinated polyethylene (CPE) and natural rubber (NR) with a blend composition ratio of 80/20 were prepared and recycled. Viscoelastic properties of the blends as a function of the recycling cycle were monitored. The results obtained revealed that, with an increase in the number of recycling cycles, a noticeable change in the viscoelastic properties of blends could be observed; that is, a decrease in the elastic contribution associated with a noticeable shift in the glass‐transition temperature of the NR phase of the blends was observed, implying a molecular change in the NR phase via a thermal chain‐scission mechanism. The influence of magnesium oxide (MgO) as an acid acceptor for CPE on the viscoelasticity of the blends was also investigated. Through a reduction of the amount of MgO, the molecular change was found to be more pronounced in NR than in CPE phases in a manner similar to the increase in the recycling cycles. An explanation of the changes in the viscoelastic properties of the blends with various MgO loadings and recycling cycles is proposed in terms of thermal degradation via a molecular chain‐scission mechanism taking place mainly in the NR phase. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology and dynamic mechanical properties of natural rubber/nitrile rubber blends containing trans‐polyoctylene rubber as a compatibilizer

The use of trans‐polyoctylene rubber (TOR) as a compatibilizer for blends of natural rubber (NR) and acrylonitrile‐butadiene rubber (NBR) was investigated using atomic force microscopy (AFM) and dynamic mechanical analysis (DMA). The NR/NBR blends containing varying proportions of TOR were prepared in an internal mixer. AFM micrographs of NR/NBR blend at 50/50 (w/w) composition showed heterogeneous phase morphology with NR as a matrix and NBR as a dispersed phase. Inclusion of TOR in the NR/NBR blend altered the phase morphology by reducing the size of the NBR phase. DMA of NR/NBR/TOR showed reduction in tan δ peak height of NBR and an increase in storage modulus E′ in the rubbery region for the NR/NBR blends. A comparison of the E′ obtained from experimental data with that from theoretical models was made to deduce the location of TOR in the blend. Based on the fittings of calculated and experimental values of E′, it was inferred that TOR was incorporated into the NR phase at lower proportion as well as at the interfacial region at higher proportion. The Cole–Cole plot illustrated the compatibilizing effect of TOR. Copyright © 2004 Society of Chemical Industry     

Miscibility Between Ethylene Vinyl Acetate Copolymers and Tackifier Resins

A series of ethylene vinyl acetate copolymer (EVA) were blended with various kinds of tackifiers and the miscibility between the components was investigated. The miscibility of the blend is illustrated as a phase diagram. The EVA and modified rosin systems tended to have a phase diagram with lower critical solution temperature (LCST), whereas the EVA and petroleum resin systems tended to have that with upper critical solution temperature (UCST). The phase diagrams of EVA/tackifier resins systematically changed as VAc content in the copolymer increased, which is accounted for by the classical Flory-Huggins theory.     

Miscibility Between Ethylene Vinyl Acetate Copolymers and Tackifier Resins

A series of ethylene vinyl acetate copolymer (EVA) were blended with various kinds of tackifiers and the miscibility between the components was investigated. The miscibility of the blend is illustrated as a phase diagram. The EVA and modified rosin systems tended to have a phase diagram with lower critical solution temperature (LCST), whereas the EVA and petroleum resin systems tended to have that with upper critical solution temperature (UCST). The phase diagrams of EVA/tackifier resins systematically changed as VAc content in the copolymer increased, which is accounted for by the classical Flory-Huggins theory.     

Influences of the phenolic curative content and blend proportions on the properties of dynamically vulcanized natural rubber/acrylonitrile–butadiene–styrene blends

The vulcanization of natural rubber (NR)‐blended acrylonitrile–butadiene–styrene (ABS) was carried out with a phenolic curing agent by a melt‐mixing process. The NR compound was first prepared before blending with ABS. The effects of the phenolic curative contents (10, 15, and 20 phr) and blend proportions (NR/ABS ratio = 50 : 50, 60 : 40, and 70 : 30) on the mechanical, dynamic, thermal, and morphological properties of the vulcanized NR/ABS blends were investigated. The tensile strength and hardness of the blends increased with increasing ABS content, whereas the elongation at break decreased. The strength property resulting from the thermoplastic component and the vulcanized NR was an essential component for improving the elasticity of the blends. These blends showed a greater elastic response than the neat ABS. The thermal stability of the blends increased with increasing ABS component. Scanning electron micrographs of the blends showed a two‐phase morphology system. The vulcanized 60 : 40 NR/ABS blend with 15‐phr phenolic resin showed a uniform styrene‐co‐acrylonitrile phase dispersed in the vulcanized NR phase; it provided better dispersion between the NR and ABS phases, and this resulted in superior elastic properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42520.     

Dichlorocarbene modification of natural rubber and its role as a modifier in blends of natural rubber and hydrogenated nitrile rubber

Dichlorocarbene modification of natural rubber (NR) carried out by alkaline hydrolysis of chloroform in presence of cetyl trimethyl ammonium bromide as phase‐transfer catalyst was investigated. Extent of chemical reaction was characterized by estimation of chlorine content and FTIR studies. Rate of dichlorocarbene addition depends on the time and temperature of reaction. Reaction carried out at 60°C for 2 h yielded a material with a chlorine content of 15%. Chemical modification of NR was accompanied by introduction of chlorine through cyclopropyl ring to the main chain of NR as revealed from FTIR studies. As level of chlorination increased, the physical nature of NR changed from a soft flexible state to a hard nontacky form. Blends of NR with hydrogenated nitrile rubber (HNBR) containing three to seven parts of dichlorocarbene‐modified NR (DCNR) of chlorine content 15% could be prepared by conventional mill mixing. Incorporation of DCNR into blends of NR and HNBR promoted polar interaction between the chlorine segments and acrylonitrile segments of the blend as shown from the shift in characteristic IR absorption peaks and shift in T_g from DSC studies. As a consequence, DCNR acted as an interface modifier in blends of NR and HNBR. Blends of NR and HNBR containing DCNR showed a considerable improvement in cure behavior, physical properties, and ageing characteristics in oil, ozone, and high temperature compared to pure blends of NR and HNBR. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4401–4409, 2006     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Mechanical properties and blend compatibility of natural rubber –chlorosulfonated polyethylene blends

Natural rubber (NR) was blended with chlorosulfonated polyethylene (CSM) with various formulation and blend ratios (NR/CSM: 80/20 –20/80, wt/wt). Rubber blends were prepared by using a two‐roll mill and vulcanized in a compression mold to obtain the 2 mm‐thick sheets. Tensile properties, tear resistance, thermal aging resistance, ozone resistance, and oil resistance were determined according to ASTM. Compatible NR/CSM blends are derived from certain blends containing 20–30% CSM without adding any compatibilizing agent. Tensile and tear strength of NR‐rich blends for certain formulations show positive deviation from the rule of mixture. Thermal aging resistance depends on formulation and blend ratio, while ozone and oil resistance of the blends increase with CSM content. Homogenizing agents used were Stuktol®60NS and Epoxyprene®25. Stuktol®60NS tends to decrease the mechanical properties of the blends and shows no significant effect on blend morphology. Addition of 5–10 phr of epoxidized natural rubber (ENR, Epoxyprene® 25) increases tensile strength, thermal aging resistance, and ozone resistance of the blends. It is found that ENR acts as a compatibilizer of the NR/CSM blends by decreasing both CSM particle size diameter and α transition temperature of CSM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 127–140, 2006     

Mechanical properties of thermoplastic elastomeric blends of chitosan and natural rubber latex

Thermoplastic chitosan/natural rubber blends (Cs/NR) were prepared from natural rubber latex and chitosan by solution casting technique. The blends were characterized by mechanical analysis (stress–strain) and the mechanical properties were found to vary with chitosan/natural rubber ratios. Experimental values were compared with different theoretical models. Effect of thermal aging on mechanical properties was also investigated. Dicumyl peroxide was used as the crosslinking agent. The effect of crosslinking on mechanical properties of Cs/NR has also been studied. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Blending of natural rubber with linear low-density polyethylene

Blends of natural rubber (NR) with linear low-density polyethylene (LLDPE) were prepared by melt blending of the materials in a plasticorder mixer at various temperatures around the melting point of LLDPE and at various mixing rates. The optimum processing conditions were a temperature of about 135°C and a mixing rate of 55 rpm. The tensile properties, stress and strain, of the blend had improved significantly with the addition of liquid natural rubber (LNR) into the blend. For blends with compositions around 50% NR, about 10–15% LNR produced the most significant improvement in the physical properties. Welldispersed plastic particles in a rubber matrix were strongly indicated in these samples. Scanning electron micrographs (SEM) of the samples also indicated an increase in the homogeneity of the mixes with the addition of LNR. A single glass transition temperature of about?55°C for the blend was observed via dynamic mechanical analysis (DMA). Interfacial linking between the NR and LLDPE phases was attributed to the presence of active groups on the polyisoprene chain of LNR, which induced the interphase reaction between the NR and LLDPE phases. © 1995 John Wiley & Sons, Inc.     

Development of novel elastomeric blends containing natural rubber and ultra-low-density polyethylene

This study sought to develop novel elastomeric compounds using natural rubber (NR) and ultra-low-density polyethylene (ULDPE). Blends were prepared by means of a two-roll mill for three ratios (70/30, 60/40, and 50/50 NR/ULDPE). Conventional vulcanization was performed in a compression mold. The physical and mechanical properties of the blend were determined according to ASTM standards. The results were compared with those obtained from NR blended with styrene-butadiene rubber (SBR). The morphological examinations with scanning electron microscopy indicated that ULDPE was compatible with NR; thus, the addition of a compatibilizer was not necessary. The cocontinuous phase was dominant in the NR/ULDPE blend containing 50 and 60 wt % NR. The tensile properties, tear resistance, and aging resistance of the NR/ULDPE blends were found to be superior to those of NR/SBR blends. On the other hand, the abrasion and flex cracking resistances of the NR/ULDPE blend were inferior to those exhibited by SBR blends but the Mooney viscosity and resilience of both blends fell in the same range. However, the addition of dicumyl peroxide appeared to have caused crosslinking of the ULDPE phase in the blend, which in turn increased the tensile properties and abrasion and aging resistance. The properties of the tertiary NR/SBR/ULDPE blend were investigated as well. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 650–660, 2001     

Thermoplastic elastomers-based natural rubber and thermoplastic polyurethane blends

Thermoplastic elastomers based on the blends of thermoplastic polyurethane (TPU) and natural rubber were prepared by a simple blend technique. The influence of the two different types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends was investigated. The main aim of this study was to improve heat resistance and damping properties, and also to prepare the TPU material with low hardness by blending with various amounts of natural rubber. It was found that the TPU/ENR blends exhibited superior modulus, hardness, shear viscosity, stress relaxation behavior and heat-resistant properties compared to the blends with TPU and unmodified NR. This was attributed to higher chemical interaction between the polar functional groups of ENR and TPU by improving the interfacial adhesion. It was also found that the ENR/TPU blends exhibited finer grain morphology than the blends with unmodified NR. Furthermore, lower tension set, damping factor (Tan ??) and hardness, but higher degradation temperature, were observed in natural rubber/TPU blends compared to pure TPU. This proves the formation of TPU material with high heat resistance, low hardness and better damping properties. However, the blends with higher proportion of natural rubber exhibited lower tensile strength and elongation at break.     

Novel dynamic vulcanization of polyethylene and ozonolysed natural rubber blends: Effect of curing system and blending ratio

Dynamic vulcanization was studied in terms of the change in α‐relaxation temperatures of the LDPE matrix, morphology, and mechanical properties of LDPE/ozonolysed NR blends which were vulcanized at various blend ratios and with different curing systems, i.e., peroxide and sulfur systems. The ozonolysed NR with M _w = 8.30 × 10⁵ g mol⁻¹ and M _n = 2.62 × 10⁵ g mol⁻¹, prepared by the in situ ozonolysis reaction of natural rubber latex, was used in this study. The significant change in the α‐relaxation temperature of LDPE in the LDPE/ozonolysed NR, dynamically vulcanized using the sulfur system, suggested that sulfur vulcanization of the blend gave a higher degree of crosslink density than using peroxide and corresponded with the improved damping property and homogenous phase morphology. However, the peroxide cured blends of LDPE/ozonolyzed NR gave more improvement of tensile strength and elongation at break than the sulfur cured system. Furthermore, the mechanical properties of tensile strength, elongation at break, and damping were improved by increasing the ozonolyzed natural rubber content in both DCP and sulfur cured blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Stress‐relaxation behavior of natural rubber/polystyrene and natural rubber/polystyrene/natural rubber‐graft‐polystyrene blends

We studied the stress‐relaxation behavior of natural rubber (NR)/polystyrene (PS) blends in tension. The effects of strain level, composition, compatibilizer loading, and aging on the stress‐relaxation behavior were investigated in detail. The dispersed/matrix phase morphology always showed a two‐stage mechanism. On the other hand, the cocontinuos morphology showed a single‐stage mechanism. The addition of a compatibilizer (NR‐g‐PS) into 50/50 blends changed the blend morphology to a matrix/dispersed phase structure. As a result, a two‐step relaxation mechanism was found in the compatibilized blends. A three‐stage mechanism was observed at very high loadings of the compatibilizer (above the critical micelle concentration), where the compatibilizer formed micelles in the continuous phase. The aged samples showed a two‐stage relaxation mechanism. The rate of relaxation increased with strain levels. The aging produced interesting effects on the relaxation pattern. The rate of relaxation increased with temperature due to the degradation of the samples. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Cure characteristics and mechanical properties of hydrogenated natural rubber/natural rubber blends

The cure characteristics and mechanical properties of blends consisting of hydrogenated natural rubber (HNR) and natural rubber (NR) blends were investigated. The HNR/NR blends at 50/50 wt ratio were vulcanized using various cure systems: peroxide vulcanization, conventional vulcanization with peroxide, and efficient vulcanization with peroxide. The HNR/NR vulcanizates cured by the combination of peroxide and sulfur donor (tetramethylthiuram disulfide, TMTD) in the efficient vulcanization with peroxide exhibited the best mechanical properties. It was also found that the hydrogenation level of HNR did not affect the tensile strength of the vulcanizates. The tensile strength of the blends decreased with increasing HNR content because of the higher incompatibility to cause the noncoherency behavior between NR and HNR. However, the HNR/NR vulcanizate at 50/50 wt ratio showed the maximum ultimate elongation corresponding to a co‐continuous morphology as attested to by scanning electron micrographs. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009