Surface graft copolymerization of 2‐hydroxyethyl methacrylate onto low‐density polyethylene film through corona discharge in air

The corona discharge technique was explored as a means of forming chemically active sites on a low‐density polyethylene (LDPE) film surface. The active species thus prepared at atmospheric pressure in air was exploited to subsequently induce copolymerization of 2‐hydroxyethyl methacrylate (HEMA) onto LDPE film in aqueous solution. The results showed that with the corona discharge voltage, reaction temperature, and inhibitor concentration in the reaction solution the grafting degree increased to a maximum and then decreased. As the corona discharge time, reaction time, and HEMA concentration in the reaction solution increased, the grafting degree increased. With reaction conditions of a 5 vol % HEMA concentration, 50°C copolymerization temperature, and a 2.0‐h reaction time, the degree of grafting of the LDPE film reached a high value of 158.0 μg/cm² after treatment for 72 s with a 15‐kV voltage at 50 Hz. Some characteristic peaks of the grafted LDPE came into view at 1719 cm^?1 on attenuated total reflectance IR spectra (C?O in ester groups) and at 531 eV on electron spectroscopy for chemical analysis (ESCA) spectra (O_1s). The C_1s core level ESCA spectrum of HEMA‐grafted LDPE showed two strong peaks at ～286.6 eV (? C ? O? from hydroxyl groups and ester groups) and ～289.1 eV (O?C ? O? from ester groups), and the C atom ratio in the ? C? O? groups and O?C? O groups was 2:1. The hydrophilicity of the grafted LDPE film was remarkably improved compared to that of the ungrafted LDPE film. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2881–2887, 2001     

Graft copolymerization and characterization of 2‐hydroxyethyl methacrylate onto jute fiber by photoirradiation

UV radiation induced graft copolymerization of 2‐hydroxyethyl methacrylate onto natural lignocellulose (jute) fiber was carried out by two methods: simultaneous irradiation and grafting and preirradiation grafting. 1‐Hydroxycyclohexyl‐phenylketone was used as the photoinitiator in both methods. In the former method, the variation of the graft weight was measured for different values of radiation exposure time and the concentrations of both the monomer and photoinitiator. The latter method produced up to 76% graft weight compared to 45% obtained with the former method. The preirradiation method offers better control of the homopolymerization reaction compared to that afforded by the other method. The optimum value of the reaction parameters on the graft weight was evaluated. The mechanical properties of grafted samples were found to be drastically different from those of the as‐received ones and the effect was proportional to the percentage of graft weight. Differential scanning calorimetry studies showed that the percentage of graft add‐on of hydroxyethyl methacrylate with jute had a significant effect on the thermal properties. IR studies indicated the degree of grafting could be estimated by correlating the band intensities with the graft weight. The jute samples grafted with poly(hydroxyethyl methacrylate) at a level of 12% graft weight exhibited a maximum 20% increase in hydrophilicity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2898–2910, 2006     

Photoinitiated graft copolymerization of hydroxyethyl methacrylate onto cotton cellulose

The photoinitiated graft copolymerization of hydroxyethyl methacrylate (HEMA) onto cotton cellulose was studied using uranyl nitrate (UN) and ceric ammonium nitrate (CAN) photoinitiators. Optimization of various parameters of the graft-copolymerization reaction viz., time, temperature, initiator, and monomer concentration, was carried out. The optimized conditions of grafting were employed to cotton samples swollen in zinc chloride as well as sodium hydroxide. Graft add-on was found to be dependent on the nature of substrate and the concentrations of monomer and photoinitiator. UN was found to be the better photoinitiator, giving higher grafting with HEMA. The grafted samples showed initially decrease and then marginal increase in the moisture regain with increase in graft add-on. The dye uptake of both direct and reactive dyes decreased with increase in graft add-on.     

羟乙基纤维素与丙烯酸-2-羟基丙酯的反应规律

以硝酸铈铵/乙二胺四乙酸(CAN/EDTA)为引发剂,研究了羟乙基纤维素(HEC)与丙烯酸-2-羟基丙酯(HPA)的接枝共聚反应,讨论了单体浓度、引发剂浓度、反应温度、反应时间等因素对接枝率的影响,试验结果表明:在引发剂CAN和EDTA为22mmol/L,单体HPA为0.31mol/L,反应温度为40℃,反应时间为4h时,接枝率和接枝效率值最佳,并用红外光谱对接枝共聚物结构进行了鉴定。     

Simultaneous graft copolymerization of 2‐hydroxyethyl methacrylate and acrylic acid onto polydimethylsiloxane surfaces using a two‐step plasma treatment

Acrylic acid (AAc) and 2‐hydroxyethyl methacrylate (HEMA) mixtures were simultaneously grafted onto the surfaces of polydimethylsiloxane (PDMS) films using a two‐step oxygen plasma treatment (TSPT). The first step of this method includes: oxygen plasma pretreatment of the PDMS films, immersion in HEMA/AAc mixtures, removal from the mixtures, and drying. The second step was carried out by plasma copolymerization of preadsorbed reactive monomers on the surfaces of dried pretreated films. The effects of pretreatment and polymerization time length, monomer concentration, and ratio on peroxide formation and graft amount were studied. The films were characterized by attenuated total reflection Furrier transformer infrared (ATR‐FTIR) spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), zeta potential, surface tension, and water contact angle measurements. The ATR‐FTIR spectrum of the modified film after alkaline treatment showed the two new characteristic bands of PHEMA and PAAc. Both increase the polar part of surface tension (γ_p) after grafting and the evaluation of surface charge at pH 1.8, 7, and 12 confirmed the presence of polar groups on the surface of grafted films with a mixture of HEMA/AAc. Morphological studies using both AFM and SEM evaluation illustrated various amounts of grafted copolymer on the surface of PDMS films. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

微波法接枝改性天然胶乳的制备与表征

采用微波辐射的方法对天然浓缩胶乳进行接枝改性,单体选用甲基丙烯酸甲酯,考察了微波温度、时间、引发剂和单体用量对接枝率、接枝效率的影响,用傅里叶变换红外光谱仪、核磁共振波谱仪来表征接枝产物。结果表明,微波法接枝改性天然胶乳的方法是可行的;适宜的反应条件为:采用过硫酸钾和亚硫酸钠作为引发剂,其用量为0.4%(占橡胶质量的百分数),微波温度为80℃,反应时间为1～2h,单体与胶乳质量比为1∶1。     

Studies on graft copolymerization of cyclohexyl methacrylate onto chloroprene rubber

Graft copolymerization of cyclohexyl methacrylate (CMA) onto chloroprene rubber (CR) was carried out in toluene using benzoyl peroxide as an initiator. The graft copolymer was isolated from the gross polymer by extracting it with a butanone solution. Infrared (IR) spectra of the graft copolymer showed the occurrence of grafting. Optimization of various parameters of the grafting, namely, time, temperature, and initiator concentrations, was performed. The mechanical adhesive properties of the graft copolymer, CR-g-CMA, were measured and compared with those of the graft copolymer of methyl methacrylate (MMA) onto CR, CR-g-MMA. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1733–1737, 1997     

Graft copolymerization of hydroxyethyl methacrylate onto chitosan

Chitosan is a polysaccharide derived from chitin, which is commonly found in shellfish waste materials. The present work is concerned with the graft copolymerization of 2-hydroxyethylmethacrylate (HEMA) onto chitosan using thiocarbonation–potassium bromate for redox initiation. The combined effects of the principal reaction variables for the grafting reaction were studied systematically. This grafting reaction was studied with respect to percentages of graft yield (%G.Y.), homopolymer (%H.P.), and total conversion (%T.C.). A tentative polymerization mechanism is proposed. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 683–702, 2001     

Effect of ultrasonic irradiation on ceric‐salt‐initiated grafting of methyl methacrylate onto regenerated cellulose film

Effect of ultrasonic irradiation on ceric salt (Ce⁴⁺)‐initiated grafting of methyl methacrylate (MMA) on regenerated cellulose film (thickness = 20 μm) was investigated under an air atmosphere in water solvent at 60°C. The grafting system with the ultrasonic irradiation was characterized by higher percentage of grafting and graft efficiency than the system without the irradiation. Reaction of cellulose with Ce⁴⁺ was also accelerated by the ultrasonic irradiation. No accelerating effect of grafting due to the ultrasonic irradiation was observed for the system under reduced pressure of 5 torr. The effect of the ultrasonic irradiation on the average molecular weight of MMA‐grafted chains was also studied. Moreover, the surface layer of the resulting grafted films was examined by attenuated total reflection–infrared (ATR–IR) measurement and scanning electron microscopy (SEM) observation. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 251–258, 1999     

Hardness of irradiated hydroxyethyl methacrylate copolymer at elevated temperatures

The hardness of irradiated hydroxyethyl methacrylate (HEMA) copolymer at elevated temperatures was measured using a microhardness tester. The hardness increases with annealing time, and is attributed to the defects present in the molecular chains. The defects that control the hardness are related to the entanglement of polymer chain and follow a first order kinetics process. The relaxation time satisfies the Arrhenius equation, with constant activation energy of 25 kJ/mol independent of the irradiation dose. The results were compared with those of PMMA and LiF single crystals reported in the literature. The present findings are useful in the study of soft contact lens, kidney dialysis system, drug delivery system, and artificial liver support system. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Factorial experimental design for graft copolymerization of styrene and methyl methacrylate onto styrene–butadiene rubber

The graft copolymerization of styrene (ST) and methyl methacrylate (MMA) onto styrene–butadiene rubber (SBR) latex prepared by seeded emulsion polymerization has been studied under various reaction conditions using cumene hydroperoxide redox initiator. The mechanism of graft copolymerization has been investigated. The synthesized graft copolymers were purified and then characterized by proton nuclear magnetic resonance (¹H NMR) analysis. A 2 2 fractional factorial experimental design was applied to study the effects of the process variables such as the amount of initiator and emulsifier, the presence or absence of chain‐transfer agent, ST to MMA ratio, monomer to rubber ratio, and reaction temperature on the grafting efficiency. The analysis of the results from the design showed the sequence of the main effect on the observed response of the grafting of ST and MMA onto SBR and that the amount of chain‐transfer agent had a significant effect. Transmission electron microscopy was used to study the morphology of the graft copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2867–2874, 2006     

羧甲基甲壳素接枝甲基丙烯酸甲酯的制备及成膜性

通过高速搅拌,未使用乳化剂,制备了羧甲基甲壳素和甲基丙烯酸甲酯的接枝共聚物,避免了产物中引入乳化剂杂质。利用红外光谱对接枝共聚物进行了表征。考察了不同接枝率的产物在12种常见溶剂中的溶解性,结果表明,不同接枝率的接枝共聚物都有良好的水溶性,可以形成无色透明的膜,扩大了其实际应用价值。     

Graft copolymerization of polyethylene glycol methacrylate onto polyethylene film and its blood compatibility

In an attempt to produce surfaces that show low levels of adsorption of protein and adhesion of platelets, different molecular weights of polyethylene glycol methacrylate (PEG‐MA) were grafted onto polyethylene film by a preirradiation grafting process. The extent of grafting was found to be dependent on the storage condition of the irradiated polyethylene film, the preirradiated dose, reaction time and temperature, molecular weight of PEG‐MA, and the type of solvent. The grafting yield was found to decrease rapidly with storage time for irradiated polyethylene film stored at room temperature. On the other hand, the grafting yield in the irradiated polyethylene stored at −130°C remained nearly constant up to 20 days after irradiation. The grafting yield decreased with an increased PEG‐MA molecular weight. Human plasma protein was adsorbed onto control and PEG‐MA‐grafted polyethylene film surfaces, and the relative adsorbed amount of proteins on the surfaces was evaluated by electron spectroscopy for chemical analysis. The adsorbed protein and platelet adhesion on the polyethylene film surface decreased rapidly with the grafting yield. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 631–641, 1999     

Microwave irradiation copolymerization of superabsorbents from cornstarch and sodium acrylate

Sodium acrylate was grafted onto cornstarch by microwave irradiation to synthesize a superabsorbent, in which potassium persulfate (PPS) was used as the initiator and polyethyleneglycol diacrylate as the crosslinker. It was found that microwave irradiation could substantially accelerate the synthesis, without the need to remove O₂ or inhibitor. Catalyzed by p‐toluene sulfonic acid, polyethyleneglycol was esterified with acrylate to synthesize the crosslinker. An orthogonal test of L₉(3⁴) was designed to study the effects of relevant factors on absorbency and yield of products, including microwave power, irradiation time, initiator amount, and crosslinker content. Microwave power was believed to be the most significant factor affecting the swelling ratio and solubility of the product. Optimized experimental results showed that 10 min of microwave irradiation at 85–90 W could produce a cornstarch‐based superabsorbent with a swelling ratio of 520–620 g/g in distilled water and solubility of 8.5–9.5 wt %. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 264–269, 2005     

高氯氯化聚乙烯对CR与MMA接枝共聚合的影响

以甲苯为溶剂,在９０℃条件下,研究了１０份氯含量为５７％的高氯氯化聚乙烯（ＨＣＰＥ）对１００份粘接型氯丁橡胶与７５份甲基丙烯酸甲酯（ＭＭＡ）接枝共聚合的影响。结果表明,该体系与无ＨＣＰＥ体系相比,ＭＭＡ转化率约提高４０％,产物接枝效率约高５０％,接枝度约高９０％。产物含有较高相对分子质量的级分,相对分子质量分布较宽,并且有较好的物理机械性能和较高粘接强度。     

Graft copolymerization of benzyl methacrylate onto wool fibers

Benzyl methacrylate (BzMA) was graft copolymerized onto wool fibers by using ammonium peroxydisulphate as the initiator. Grafted samples with different polymer add ons (from 7 to 180%) were obtained by varying the monomer concentration in the reaction system. Following grafting with BzMA, the X-ray diffraction peak at 20.2° slightly moved towards higher spacing values. Birefringence decreased, indicating a lower degree of molecular orientation of grafted wool fibers. The equilibrium regain values of grafted wool decreased with increasing add on. Tensile strength increased in the range 45–77% add on, while elongation at break decreased. Differential scanning calorimetry (DSC) and thermogravimetry (TG) measurements showed a higher thermal stability for grafted wool. Following grafting, the drop of dynamic storage modulus (E′) shifted to a lower temperature. Accordingly, the intensity of the loss modulus (E′) peak decreased, indicating that the thermally induced molecular motion was enhanced by grafting. Thermomechanical analysis (TMA) confirmed the increase in chain mobility for the grafted wool fibers. Above 35–40% add on, the presence of homopolymer on the surface of the wool fibers was identified by scanning electron microscopy. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 343–350, 1997     

Thermal‐initiated hydroxyethyl methacrylate functionalization of multiwalled carbon nanotubes

Multiwalled‐carbon nanotubes (MWCNTs) were functionalized via thermoinitiated free radical polymerization of 2‐hydroxyethyl methacrylate (HEMA) using benzoyl peroxide. Tip sonication was used during the polymerization reaction to separate agglomerated nanotubes. The functionalization was confirmed by control experiments and attenuated total reflectance Fourier transform infrared spectroscopy (ATR‐FTIR). Differential scanning calorimetry indicated that the addition of poly(HEMA)‐MWCNTs to a two‐component polyurethane coating will have little effect on the glass transition temperature of the coating. The poly(HEMA)‐functionalized MWCNTs formed large colloidal structures of highly dispersed nanotubes in both the nonsheared and sheared coatings as determined by atomic force microscopy. This study determined a quick and easy method to functionalize MWCNTs for incorporation into a two‐component polyurethane coating. A simple method for producing ordered structures of the MWCNTs via shear observed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Hydrogels based on gelatin poly(hydroxyethyl methacrylate) and poly(butyl acrylate) graft copolymer impregnated with fibrin

Gelatin was graft copolymerized with poly(hydroxyethyl methacrylate and butyl acrylate) and subsequently crosslinked with glutaraldehyde. Fibrin of bovine origin was incorporated onto this graft copolymer and characterized for the percentage of grafting. The infrared spectroscopy, mechanical strength, and water absorption capacity of the composite were also studied. This biomaterial can be used as a hemostat in many phases of surgery and as a wound dressing material. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:555–560, 1997     

New 2‐hydroxyethyl methacrylate resins with good swelling characteristics

2‐Hydroxyethyl methacrylate copolymers with styrene and series of the cross‐linkers (divinylbenzene and mono‐, di‐ and triethylene glycol dimethacrylates) with low cross‐linking degree (2–5 mol %) were obtained by suspension polymerization. Loading capacity of the resins, their glass transition temperature, and swelling characteristics in 20 solvents were analyzed depending on monomers composition. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1487–1493, 2006     

Hexavalent-chromium-initiated graft copolymerization of methyl methacrylate onto cellulose

Graft copolymerization of methyl methacrylate (MMA) onto cotton–cellulose has been carried out using hexavalent chromium Cr(VI) as initiator. Aqueous-methanolic solution of perchloric acid has been chosen as the reaction medium. The effect of monomer, initiator, acid, reaction medium, and temperature on the graft percentage has been found out. The reactions have also been carried out in the presence of polymerization, inhibitors, and retarders, such as hydroquinone and transition metal salts like CuSO₄, FeCl₃, etc. The grafted samples, after exhaustive separation of homopolymers and purification, were subjected to various chemical, mechanical, and thermal testings. The results of various analyses have been compared with the reference, and the improvement in the graft has been evaluated. A suitable mechanism for the grafting processes has been suggested, in accordance with the experimental results.