New synthesis methods for polypropylene‐co‐ethylene‐propylene rubber

In this research, the reinforcement of polypropylene (PP) was studied using a new method that is more practical for synthesizing polypropylene‐block‐poly(ethylene‐propylene) copolymer (PP‐co‐EP), which can be used as a rubber toughening agent. This copolymer (PP‐co‐EP) could be synthesized by varying the feed condition and changing the feed gas in the batch reactor system using Ziegler–Natta catalysts system at a copolymerization temperature of 10°C. The ¹³C‐NMR tested by a 21.61‐ppm resonance peak indicated the incorporation of ethylene to propylene chains that could build up the microstructure of the block copolymer chain. Differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and dynamic mechanical analysis (DMA) results also confirmed these conclusions. Under these conditions, the morphology of copolymer trapped in PP matrix could be observed and the copolymer T_g would decrease when the amount of PP‐co‐EP was increased. DMA study also showed that PP‐co‐EP is good for the polypropylene reinforcement at low temperature. Moreover, the PP‐co‐EP content has an effect on the crystallinity and morphology of polymer blend, i.e., the crystallinity of polymer decreased when the PP‐co‐EP content increased, but tougher mechanical properties at low temperature were observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3609–3616, 2007     

Structure and morphology of polyethylene/polypropylene in‐reactor alloys synthesized by spherical high‐yield Ziegler–Natta catalyst

A series of spherical polyethylene/polypropylene (PE/PP) in‐reactor alloys were synthesized with spherical high‐yield Ziegler–Natta catalyst by sequential multistage polymerization in slurry. The morphology of PE/PP alloy granule was evaluated by optical microscopy, scanning electron microscopy, and transmission electron microscopy. The results show PE/PP in‐reactor alloy with excellent morphology, high porosity, and narrow distribution of the particle size. The PE/PP in‐reactor alloys show excellent mechanical properties with good balance between toughness and rigidity. It was fractionated into five fractions by temperature‐gradient extraction fractionation, and every fractionation was analyzed by FTIR, ¹³C‐NMR, DSC, and WAXD. The PE/PP in‐reactor alloy was found to contain mainly five portions: PP, PE, segmented copolymer with PP and PE segment of different length, ethylene‐b‐propylene copolymer, and an ethylene–propylene random copolymer. The characteristic chain structure leads to good compatibility between the fractions of the alloy that shows a multiphase structure. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2075–2085, 2007     

Crystallization,melting behavior,and morphology of BPP/HDPE blend

The crystallization, melting behavior, and morphology of a low ethylene content block propylene–ethylene copolymer (BPP) and a high-density polyethylene (HDPE) blend were studied. It was found that the existence of ethylene–propylene rubber (EPR) in BPP has more influence on the crystallization of HDPE than on that of PP. This leads to the decreasing of the melting temperature of the HDPE component in the blends. It is suggested that the EPR component in BPP shifted to the HDPE component during the blending process. The crystallinity of the HDPE phase in the blends decreased with increasing BPP content. The morphology of these blends was studied by polarized light microscopy (PLM) and SEM. For a BPP-rich blend, it was observed that the HDPE phase formed particles dispersed in the PP matrix. The amorphous EPR chains may penetrate into HDPE particles to form a transition layer. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 69: 2469–2475, 1998     

Toughening of PP/EPDM blend by compatibilization

To improve the mechanical properties of blends of polypropylene (PP) and terpolymer of ethylene–propylene–diene (EPDM), a triblock copolymer, (PP‐g‐MAH)‐co‐[PA‐6,6]‐co‐(EPDM‐g‐MAH), was synthesized by coupling reaction of maleic anhydride (MAH)‐grafted PP (PP‐g‐MAH), EPDM‐g‐MAH, and PA‐6,6. The newly prepared block copolymer brought about a physical interlocking between the blend components, and imparted a compatibilizing effect to the blends. Introducing the block copolymer to the blends up to 5 wt % lead to formation of a β‐form crystal. The wide‐angle X‐ray diffractograms measured in the region of 2θ between 10° and 50° ascertained that incorporating the block copolymer gave a new peak at 2θ = 15.8°. The new peak was assigned to the (300) plane spacings of the β‐hexagonal crystal structure. In addition, the block copolymer notably improved the low‐temperature impact property of the PP/EPDM blends. The optimum usage level of the compatibilizer proved to be 0.5 wt %. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1267–1274, 2000     

Study of crystallization and melting behavior of polypropylene‐block‐polyethylenes copolymers fractionated from polypropylene and polyethylene mixtures

A series of ethylene–propylene block copolymer fractions of differing compositions, while still retaining broad molecular weight distributions, were obtained by fractionation of polypropylene (PP) and polyethylene (PE) copolymers prepared by sequential polymerization of ethylene and propylene. The crystallization and melting behavior of the polypropylene‐block‐polyethylene fractions were studied. It was observed that the major component could suppress crystallization of the minor component, leading to a decrease in crystallinity and melting temperature. Non‐isothermal crystallization showed that crystallization of the ethylene block was less influenced by composition and cooling rate than the propylene block. At fast cooling rates, the ethylene block could crystallize prior to the propylene block. Isothermal crystallization kinetics experiments were also conducted. We found that the block copolymers with minor ethylene components had smaller Avrami exponents (n ≈ 1.0), hence indicating a reduced growth dimension of the PE crystals by the pre‐existing PP crystals. On the other hand, the ethylene block exhibited much larger Avrami exponents in those block copolymers with major ethylene contents. Copyright © 2004 Society of Chemical Industry     

Thermal analysis, X-ray and electron diffraction studies on crystalline phase transitions in solvent-treated poly(hexamethylene terephthalate)

The crystal polymorphism, transformation, and morphologies in chloroform solvent-cast poly(hexamethylene terephthalate) (PHT) were examined by using differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), and temperature in situ transmission electron microscopy (TEM). Solvent-induced crystallization of PHT at room temperature yielded an initial crystal of γ-form, as confirmed by WAXD. Upon DSC scanning, the original γ-form in PHT exhibited three endothermic peaks, whose origins and association were carefully analyzed. The first peak, much smaller than the other two, is in the temperature range of ca. 100-120 °C. It was found that the solvent-induced γ-form was transformed to β-form at 125 °C via a solid-to-solid transformation mechanism. In addition, WAXD showed that γ- and β-forms co-existed in the temperature range of 100-125 °C. These mixed crystal forms were further identified using TEM, and the selected-area electron diffraction (ED) patterns revealed that both γ- and β-form crystals co-existed and were packed within the same spherulite. Solid-solid transformation from the solvent-induced γ-form to β-form in PHT upon heat scanning was presented with evidence and discussed.     

Effect of the structure on the morphology and spherulitic growth kinetics of polyolefin in‐reactor alloys

Four polyolefin in‐reactor alloys with different compositions and structures were prepared by sequential polymerization. All the alloys were fractionated into five fractions: a random copolymer of ethylene and propylene (25°C fraction), an ethylene–propylene segmented copolymer (90°C fraction), an ethylene homopolymer (110°C fraction), an ethylene–propylene block copolymer (120°C fraction), and a propylene homopolymer plus a minor ethylene homopolymer of high molecular weight (>120°C fraction). The effect of the structure on the morphology and spherulitic growth kinetics of the polypropylene (PP) component in the alloys was investigated. The polyolefin alloys containing a suitable block copolymer fraction and a larger amount of PP had a more homogeneous morphology, and the crystalline particles were smaller. Quenching the polyolefin alloys led to smaller crystallites and a more homogeneous morphology as well. Isothermal crystallization was carried out above the melting temperature of polyethylene, and the growth of PP spherulites was monitored with polarized optical microscopy with a hot stage. The alloys with higher propylene contents exhibited a faster spherulitic growth rate. The fold surface free energy was derived, and it was found that a large amount of block copolymer fractions and random copolymer fractions could reduce the fold surface free energy. The structure of the alloys also affected the crystallization regime of PP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 632–638, 2005     

Influence of copolymerization conditions on the structure and properties of polyethylene/polypropylene/poly(ethylene‐co‐propylene) in‐reactor alloys synthesized in gas‐phase with spherical ziegler‐natta catalyst

A spherical TiCl₄/MgCl₂‐based catalyst was used in the synthesis of polyethylene/polypropylene/poly (ethylene‐co‐propylene) in‐reactor alloys by sequential homopolymerization of ethylene, homopolymerization of propylene, and copolymerization of ethylene and propylene in gas‐phase. Different conditions in the third stage, such as the pressure of ethylene–propylene mixture and the feed ratio of ethylene, were investigated, and their influences on the compositions, structural distribution and properties of the in‐reactor alloys were studied. Increasing the feed ratio of ethylene is favorable for forming random ethylene–propylene copolymer and segmented ethylene–propylene copolymer, however, slightly influences the formation of ethylene‐b‐propylene block copolymer and homopolyethylene. Raising the pressure of ethylene–propylene mixture results in the increment of segmented ethylene–propylene copolymer, ethylene‐b‐propylene block copolymer, and PE fractions, but exerts a slight influence on both the random copolymer and PP fractions. The impact strength of PE/PP/EPR in‐reactor alloys can be markedly improved by increasing the feed ratio of ethylene in the ethylene–propylene mixture or increasing the pressure of ethylene–propylene mixture. However, the flexural modulus decreases as the feed ratio of ethylene in the ethylene–propylene mixture or the pressure of ethylene–propylene mixture increases. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2481–2487, 2006     

Multilayered core–shell structure of the dispersed phase in high‐impact polypropylene

The multiphase morphology of high impact polypropylene (hiPP), which is a reactor blend of polypropylene (PP) with ethylene–propylene copolymer, was investigated by transmission electron microscopy, selected area electron diffraction, atomic force microscopy, and field‐emission scanning electron microscopy techniques in conjunction with an analysis of the hiPP composition and chain structure based on solvent fractionation, ¹³C‐NMR, and differential scanning calorimetry measurements. A multilayered core–shell structure of the dispersed phase of hiPP in solution‐cast films and the bulk was observed. The inner core was mainly composed of polyethylene (including its long blocks) together with part of PP, the intermediate layer was ethylene–propylene random copolymer, and the outer shell consisted of ethylene–propylene multiblock copolymers. The formation process and controlling factors of the multilayered core–shell structure are discussed. This kind of multiphase morphology of hiPP caused the material to possess both a high rigidity and high toughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

X-ray studies of multiple melting behavior of poly(butylene-2,6-naphthalate)

Multiple melting behavior of poly(butylene-2,6-naphthalate) (PBN) was studied with X-ray analysis and differential scanning calorimetry (DSC). Double endothermic peaks L and H attributed to the α-form crystal modification, a small peak attributed to the β-form crystal modification, and a new shoulder peak S at a lower temperature of peak H appeared in the DSC melting curves. Wide-angle X-ray diffraction patterns of the samples isothermally crystallized at 200 and 220 °C were obtained at a heating rate of 1 K min⁻¹, successively. In this heating process, change of crystal structure and increase of quantity of the β-form crystallites could not be observed up to the final melting. With increasing temperature, the diffraction intensity decreased gradually and then increased distinctly before a steep decrease due to the final melting. The X-ray analysis clearly proved the melt-recrystallization during heating. The β-form crystal modification was formed during slow heating process in the high temperature region.     

乙烯含量对无规共聚聚丙烯晶型及性能影响的研究

通过差示扫描量热分析、X射线衍射分析以及力学性能测试等方法,研究了不同乙烯含量的无规共聚聚丙烯（PPR）体系中,在添加定量β成核剂的条件下,乙烯含量对PPR结晶行为及热学、力学性能的影响。结果表明,PPR的熔点和结晶温度都随其乙烯含量的减少而升高;乙烯含量较少的体系,有利于β晶的形成;体系中β晶含量的提高,会使样品热变形温度提高,且冲击性能显著增强;乙烯含量的提高,增大了PPR β结晶的调控难度;实验室自制β成核剂,可使乙烯含量为0.25 %~5.1 %（质量分数,下同）的PPR中的β晶含量达到80 %以上。     

Structure and properties of polypropylene alloy in situ blends

A series of polypropylene (PP) alloys containing different ethylene contents have been prepared by the in situ sequential polymerization technique, using Ziegler–Natta catalyst (MgCl₂/TiCl₄/BMF; BMF is 9,9‐bis(methoxymethyl)fluorine, as an internal donor) without any external donor. The structure and properties of PP alloys obtained have been investigated by nuclear magnetic resonance, Fourier transform infrared spectroscopy, dynamic mechanical analysis, differential scanning calorimetry, and scanning electron microscopy (SEM). The results have suggested that PP alloys are the complex mixtures containing PP, the copolymer with long sequence ethylene chain, ethylene‐propylene rubber (EPR), and block copolymer etc. In the alloys, PP, EPR, and the copolymer with long sequence ethylene chain are partially compatible. The investigation of the mechanical properties indicates that notched Izod impact strength of PP alloy greatly increases at 16°C/?20°C in comparison with that of pure PP. The noticeable plastic deformation is observed in SEM photograph. The increase in the toughness, the mechanical strength of PP alloy decreases to a certain extent. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4804–4810, 2006     

Compared structure and morphology of nylon-12 and 10-polyurethane lamellar crystals

A comparative study of the structure and morphology of nylon-12 and 10-polyurethane (10-PUR) lamellar crystals, was carried out. Lamellar crystals were obtained by isothermal crystallization from diluted solution. Electron diffraction of lamellae combined with WAXS data recorded from crystal sediments indicated that nylon-12 crystallized in either α-form or γ-form according to the solvent chosen for crystallization. The α-form was the crystal modification predominant in doubly oriented films of nylon-12 prepared by epitaxial crystallization. On the contrary, 10-PUR invariably crystallized in α-form regardless crystallization conditions. The α-form of nylon-12 and 10-PUR shared the same crystal structure with hydrogen-bonded sheets made of antiparallel chains and stacked with progressive shifting along both b and c directions. Lamellar crystals of nylon-12 in γ-form and 10-PUR in α-form displayed similar morphological features but only the former appeared to be sensitive to temperature. Upon heating the nylon-12 crystals near to melting, the real-time WAXS analysis evidenced the occurrence of a partial γ-to-α crystal transition, and in situ AFM observations revealed the appearing of more or less regular ridges on the crystal surface. None of these changes were observed in 10-PUR crystals when subjected to similar treatment.     

Structural characterization of reactor blends of polypropylene and ethylene‐propylene rubber

Blends of isotactic polypropylene (PP), ethylene‐propylene rubber copolymer (EPR), and ethylene‐propylene crystalline copolymer (EPC) can be produced through in situ polymerization processes directly in the reactor and blends with different structure and composition can be obtained. In this work we studied the structure of five reactor‐made blends of PP, EPR, and EPC produced by a Ziegler‐Natta catalyst system. The composition of EPR was related to the ratio between ethylene and propylene used in the copolymerization step. The ethylene content in the EPR was in the range of 50–70 mol %. The crystallization behavior of PP and EPC in the blends was influenced by the presence of the rubber, and some specific interactions between the components could be established. By preparative temperature rising elution fractionation (P‐TREF) analysis, the isolation and characterization of crystalline EPC fractions were made. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2155–2162, 2004     

Crystallization Behavior of the Blends of Isotactic Polypropylene and Ethylene-Propylene Blocky Copolymers

Two ethylene-propylene copolymer fractions (EP90 and EP120) were separated from a polypropylene in-reactor alloy by extraction with n-octane at different temperatures. ¹³C-NMR shows that these two fractions have a blocky structure and WAXD reveals that both ethylene and propylene sequences in these two fractions are crystallizable. However, EP90 has higher propylene content and the average length of propylene sequences is longer. These two fractions were blended with isotactic polypropylene (PP) at various proportions, respectively, and crystallization behavior and morphology of the blends were investigated. It is found that both EP90 and EP120 are partially compatible with PP. The phase-separated domains have a nucleation effect on crystallization of PP, leading to increase in crystallization temperature and crystallinity of PP in the blends. EP90 and EP120 also affect the relative content of β crystals in an irregular way. The number of EP90-rich domains in PP/EP90 blends is larger than that of EP120-rich domains in PP/EP120 blends, but the size of EP90-rich domains is smaller, indicating that EP90 has better compatibility with PP than EP120. Spherulites are formed in all the blends. The data were analyzed with Hoffman-Lauritzen theory of crystallization regime and the free energy of the folding surface (σ_e) was derived. Addition of EP90 and EP120 has little effect on the transition temperature from regime II to regime III. The value of σ_e for the PP/EP90 blends is similar to that of neat PP, but σ_e of the PP/EP120 blends is a little higher than that of neat PP.     

Chain structure and mechanical properties of polyethylene/polypropylene/poly(ethylene‐co‐propylene)in‐reactor alloys synthesized with a spherical Ziegler–Natta catalyst by gas‐phase polymerization

Two polyethylene/polypropylene/poly(ethylene‐co‐propylene) in‐reactor alloy samples with a good polymer particle morphology were synthesized by sequential multistage gas‐phase polymerization with a spherical Ziegler–Natta catalyst. The alloys showed excellent mechanical properties, including both toughness and stiffness. With temperature‐gradient extraction fractionation, both alloys were fractionated into five fractions. The chain structures of the fractions were studied with Fourier transform infrared, ¹³C‐NMR, and thermal analysis. The alloys were mainly composed of polyethylene, polyethylene‐b‐polypropylene block copolymer, and polypropylene. There also were minor amounts of an ethylene–propylene segmented copolymer with very low crystallinity and an ethylene–propylene random copolymer. The block copolymer fraction accounted for more than 44 wt % of the alloys. The coexistence of these components with different structures was apparently the key factor resulting in the excellent toughness–stiffness balance of the materials. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 640–647, 2005     

升温淋洗分级研究聚丙烯流延膜专用料的微观结构及热学表征

采用升温淋洗分级技术分离了2种聚丙烯流延膜(CPP)专用料(CPP1、CPP2),通过红外光谱仪、差示扫描量热仪和高温凝胶色谱对2种样品的链结构、熔融和结晶行为进行了表征,确定了产品各级分的分子结构信息.结果表明,对于低温(<100℃)级分,CPP1样品中其含量为9.29％(质量分数,下同),CPP2样品中其含量为26...     

Isothermal crystallization of isotactic polypropylene blended with low molecular weight atactic polypropylene. Part I. Thermal properties and morphology development

The thermal properties and morphology development of isotactic polypropylene (iPP) homopolymer and blended with low molecules weigh atactic polypropylene (aPP) at different isothermal crystallization temperature were studied with differential scanning calorimeter and wide-angle X-ray scattering. The results of DSC show that aPP is local miscible with iPP in the amorphous region and presented a phase transition temperature at T_c=120 °C. However, below this transition temperature, imperfect α-form crystal were obtained and leading to two endotherms. While, above this transition temperature, more perfect α- and γ-form crystals were formed which only a single endotherm was observed. In addition, the results of WAXD indicate that the contents of the γ-form of iPP remarkably depend both on the aPP content and isothermal crystallization temperature. Pure iPP crystallized was characterized by the appearance of α- and γ-forms coexisting. Moreover, the highest intensity of second peak, i.e. the (0 0 8) of γ-form coexisting with (0 4 0) of α-form, and crystallinity were obtained for blended with 20% of aPP, the γ-form content almost disappeared for iPP/aPP blended with 50% aPP content. Therefore, detailed analysis of the WAXD patterns indicates that at small amount aPP lead to increasing the crystallinity of iPP blend, at larger amount aPP, while decreases crystallinity of iPP blends with increasing aPP content. On the other hand, the normalized crystallinity of iPP molecules increases with increasing aPP content. These results describe that the diluent aPP molecular promotes growth rate of iPP because the diluent aPP molecular increases the mobility of iPP and reduces the entanglement between iPP molecules during crystallization.     

Fractionation and characterization of an ethylene–propylene copolymer produced with a MgCl2/SiO2/TiCl4/diester‐type ziegler–natta catalyst

An ethylene–propylene copolymer synthesized with a Ziegler–Natta catalyst was fractionated by a combination of dissolution/precipitation and temperature‐gradient extraction fractionation. The fractions were characterized with ¹³C‐NMR, differential scanning calorimetry, and wide‐angle X‐ray diffraction. The fractionation was carried out mainly with respect to the content of ethylene, but the crystallizable propylene sequences could also exert an influence on the fractionation. The copolymer contained a series of components with wide variations in the compositions. With an increase in the ethylene content, the structure of the fractions became blockier and blockier, and the fraction extracted at 111°C had the blockiest structure. A further increase in the ethylene content led to a decrease in the length and number of the propylene sequences. Differential scanning calorimetry results showed that the composition distribution in single fractions was not homogeneous, and multiple melting peaks were observed. Wide‐angle X‐ray diffraction results revealed both polyethylene and polypropylene crystals in most of the fractions. Short propylene sequences could be included in the polyethylene crystals, and short ethylene sequences could also be incorporated into the polypropylene crystals. The incorporation of propylene sequences into polyethylene crystals strongly depended on the sequence distribution and crystallization conditions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008