Synthesis and characterization of novel benzhydrol-containing poly(amide-imide)s

A series of novel benzhydrol-containing poly(amide-imide)s (PAIs) have been prepared from a new diimide-dicarboxylic acid, N,N′-bis(4-hydroxycarbonyl)-benzhydrol-3,3′,4,4′-tetracarboxydiimide (BHTDA-DIA), with various diamines by direct polycondensation using triphenyl phosphite and pyridine as condensing agents. The polymers obtained had inherent viscosities of 0.35–0.96 dl g⁻¹. All these PAIs, except polymer PAI-2, were soluble in N-methyl-2-pyrrolidinone and N,N-dimethylacetamide containing LiCl (1 wt%). Tough and flexible PAI films could be obtained by casting PAIs from their DMAc or NMP solutions, except for polymer PAI-2. The polymer films had a tensile strength of 93–111 MPa, an elongation at break range of 4–6%, and an initial modulus range of 2.7–3.8 GPa. The glass transition temperatures of most polymers were found to be above 255 °C. These polymers were fairly stable up to a temperature around or above 400 °C, and lost 10% weight in the range 426–507 °C in nitrogen and 423–515 °C in air. © 1999 Society of Chemical Industry     

Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of new soluble poly(ester‐imide)s containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide–diacid chloride (3) containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by treating 2,2′‐dimethyl‐4,4′‐diamino‐biphenylene with trimellitic anhydride followed by refluxing with thionyl chloride. Various new poly(ester‐imide)s were prepared from 3 with different bisphenols by solution polycondensation in nitrobenzene using pyridine as hydrogen chloride quencher at 170°C. Inherent viscosities of the poly(ester‐imide)s were found to range between 0.31 and 0.35 dL g^?1. All of the poly(ester‐imide)s, except the one containing pendent adamantyl group 5e, exhibited excellent solubility in the following solvents: N,N‐dimethylformamide, tetrahydrofuran, tetrachloroethane, dimethyl sulfoxide, N,N‐dimethylacetamide, N‐methyl‐2‐pyrrolidinone, m‐cresol, o‐chlorophenol, and chloroform. The polymers showed glass‐transition temperatures between 166 and 226°C. The 10% weight loss temperatures of the poly(ester‐imide)s, measured by TGA, were found to be in the range between 415 and 456°C in nitrogen. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2486–2493, 2004     

Synthesis and photo-induced transformation of helical aromatic polyamides consisting of axially dissymmetric biphenylene joints and azobenzene segments in the backbone

Wholly aromatic polyamides having a novel helical structure were prepared by the reaction of axially dissymmetric (R)- or (S)-6,6′-dimethylbiphenyl-2,2′-dicarbonyl chloride with aromatic diamines, which are soluble in common solvents such as tetrahydrofuran and N,N-dimethylformamide. Photo-irradiation of a tetrahydrofuran solution of the polymer obtained with 4,4′-diaminoazobenzene induced a change of the helical conformation because of the trans–cis isomerization of the azobenzene units in the polymer chain. No change in the specific rotation of the polymer was observed on heating at 100°C for 4h, indicating thermal stability of its helical structure. CD spectra showed that the helical conformation was maintained in methanesulphonic acid. © 1998 SCI.     

New poly(amide imide imide)s based on tetraimide dicarboxylic acid condensed from 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,m‐aminobenzoic acid,and 4,4″‐oxydianiline and various aromatic diamines

A series of new, organosoluble, and light‐colored poly(amide imide imide)s were synthesized from tetraimide dicarboxylic acid ( I ) and various aromatic diamines by direct polycondensation with triphenyl phosphite and pyridine as condensing agents. I was prepared by the azeotropic condensation of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, m‐aminobenzoic acid, and 4,4′‐oxydianiline at a 2/2/1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP)/toluene. The thin films cast from N,N‐dimethylacetamide (DMAc) had cutoff wavelengths shorter than 400 nm (365–394 nm) and color coordinate b* values between 13.10 and 36.07; these polymers were lighter in color than the analogous poly(amide imide)s and isomeric polymers. All of the polymers were readily soluble in a variety of organic solvents, including NMP, DMAc, N,N‐dimethylformamide, dimethyl sulfoxide, and even less polar dioxane and tetrahydrofuran. The cast films exhibited tensile strengths of 90–104 MPa, elongations at break of 7–22%, and initial moduli of 1.9–2.4 GPa. The glass‐transition temperatures of the polymers were recorded at 274–319°C. They had 10% weight losses at temperatures beyond 520°C and left more than a 50% residue even at 800°C in nitrogen. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 669–679, 2003     

New poly(amide–imide)s syntheses. 17. Preparation and properties of poly(amide–imide)s derived from N-phenyl-3,3-bis[4-(4-aminophenoxy)-phenyl]phthalimidine,trimellitic anhydride,and various aromatic diamines

A dicarboxylic acid ( 1 ) bearing two phthalimide rings was prepared by the condensation of N-phenyl-3,3-bis[4-(4-aminophenoxy)phenyl]phthalimidine and trimellitic anhydride. A new family of poly(amide–imide)s having inherent viscosities of 0.65–1.65 dl/g was prepared by the triphenyl phosphite activated polycondensation of the diimide–diacid 1 with various aromatic diamines in a medium consisting of N-methyl-2-pyrrolidone (NMP), pyridine, and calcium chloride. All the resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. The soluble poly(amide–imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range 249–340°C and the 10% weight loss temperatures were above 545°C in nitrogen.     

Liquid crystalline aromatic polyesters containing para-linked dimethylbiphenylene moieties

A series of liquid crystalline aromatic polyesters containing 3,3′-dimethylbiphenyl-4,4′-dicarboxylic acid and 3,4′-dimethyl-biphenyl-4,3′-dicarboxylic acid was prepared by a melt polycondensation procedure and characterized by elemental analysis, DSC and TMA measurements, and optical polarizing microscopy. An optimal composition of the copolymer having a melting temperature around 300°C is proposed and the rheological behavior is discussed. Most of the mechanical properties of this copolymer were found to be close to those of Vectra A950® used as a reference sample. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of novel polyamides containing sulfone‐ether linkages and xanthene cardo groups

In order to obtain polyamides with enhanced solubility and processability, as well as good mechanical and thermal properties, several novel polyamides containing sulfone‐ether linkages and xanthene cardo groups based on a new diamine monomer, 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene (BAPX), were investigated. The BAPX monomer was synthesized via a two‐step process consisting of an aromatic nucleophilic substitution reaction of readily available 4‐chloronitrobenzene with 9,9‐bis(4‐hydroxyphenyl)xanthene in the presence of potassium carbonate in N,N‐dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Four novel aromatic polyamides containing sulfone‐ether linkages and xanthene cardo groups with inherent viscosities between 0.98 and 1.22 dL g^?1 were prepared by low‐temperature polycondensation of BAPX with 4,4′‐sulfonyldibenzoyl chloride, 4,4′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride, 3,3′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride and 4,4′‐[sulfonyl‐bis(2,6‐dimethyl‐1,4‐phenyleneoxy)]dibenzoyl chloride in N,N‐dimethylacetamide (DMAc) solution containing pyridine. All these new polyamides were amorphous and readily soluble in various polar solvents such as DMAc and N‐methylpyrrolidone. These polymers showed relatively high glass transition temperatures in the range 238–298 °C, almost no weight loss up to 450 °C in air or nitrogen atmosphere, decomposition temperatures at 10% weight loss ranging from 472 to 523 °C and 465 to 512 °C in nitrogen and air, respectively, and char yields at 800 °C in nitrogen higher than 50 wt%. Transparent, flexible and tough films of these polymers cast from DMAc solution exhibited tensile strengths ranging from 78 to 87 MPa, elongations at break from 9 to 13% and initial moduli from 1.7 to 2.2 GPa. Primary characterization of these novel polyamides shows that they might serve as new candidates for processable high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Synthesis and study of new poly(ester‐imide)s containing triptycene groups

A new triptycene‐containing dicarboxylic acid monomer was successfully synthesized by refluxing the diamine, bis(4‐aminophenoxy)phenyl triptycene with trimellitic anhydride in glacial acetic anhydride. A series of novel thermally stable poly(ester‐imide)s were prepared from dicarboxylic acid, bis(4‐trimellitimido phenoxy)phenyl triptycene with various diols by the direct polycondensation. The polymers were obtained in quantitative yields with inherent viscosities of 0.27–0.74 dL g^?1. The resulting polymers dissolved in N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethyl sulfoxide, and pyridine. These polymers were fairly stable up to a temperature >450°C and lost 10% weight in the range of 477°C and 575°C in nitrogen. The UV–V is absorption spectra revealed that most of the polymers had absorption maxima around 310 and 341 nm. POLYM. ENG. SCI., 54:2252–2257, 2014. © 2013 Society of Plastics Engineers     

Novel organosoluble poly(amide‐imide‐imide)s synthesized from new tetraimide‐dicarboxylic acid by condensation with 4,4′‐oxydiphthalic anhydride, 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene,trimellitic anhydride,and various aromatic diamines

A new monomer of tetraimide‐dicarboxylic acid (IV) was synthesized by starting from ring‐opening addition of 4,4′‐oxydiphthalic anhydride, trimellitic anhydride, and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene at a 1:2:2 molar ratio in N‐methyl‐2‐pyrrolidone (NMP). From this new monomer, a series of novel organosoluble poly(amide‐imide‐imide)s with inherent viscosities of 0.7–0.96 dL/g were prepared by triphenyl phosphite activated polycondensation from the tetraimide‐diacid with various aromatic diamines. All synthesized polymers were readily soluble in a variety of organic solvents such as NMP and N,N‐dimethylacetamide, and most of them were soluble even in less polar m‐cresol and pyridine. These polymers afforded tough, transparent, and flexible films with tensile strengths ranging from 99 to 125 MPa, elongations at break from 12 to 19%, and initial moduli from 1.6 to 2.4 GPa. The thermal properties and stability were also good with glass‐transition temperatures of 236–276°C and thermogravimetric analysis 10 wt % loss temperatures of 504–559°C in nitrogen and 499–544°C in air. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2854–2864, 2006     

Preparation and properties of novel soluble aromatic polyetherimides from 1,1′-bis[4-(3,4-dicarboxyphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane dianhydride and aromatic diamines

New aromatic polyetherimides containing the 1,1′-bis[4-(3,4-dicarboxyphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane dianhydride unit were prepared by a conventional two-step method from 1,1′-bis[4-(3,4-dicarboxyphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane dianhydride and several diamines. This procedure yielded high molecular weight polyetherimides with inherent viscosities of 0.22–1.29 dL/g. Most of the corresponding polyetherimides were soluble in organic solvents such as N-methyl-2-pyrrolidone, N, N-dimethylformamide, N,N-dimethylacetamide, and methylene chloride under ambient temperature. The glass transition temperatures (T_g) of these polymers were in the range of 207–264°C and the temperatures of 10% weight loss were over 520°C at a heating rate 20°C/min in nitrogen. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of some novel,soluble and light‐coloured,aromatic poly(amide–imide) copolymers

A new type of tetraimide‐dicarboxylic acid (I) was synthesized starting from the ring‐opening addition of m‐aminobenzoic acid (m‐ABA), 4,4′‐oxydiphthalic anhydride (ODPA) and 4,4′‐methylenedianiline (MDA) at a 2:2:1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP), followed by cyclodehydration to the diacid I. A series of soluble and light‐coloured poly(amide–imide–imide)s (III_a–j) was prepared by triphenyl phosphite‐activated polycondensation from the tetraimide‐diacid I with various aromatic diamines (II_a–j). All films cast from DMAc had cutoff wavelengths shorter than 400 nm (376–393 nm) and had b* values between 20.46 and 40.67; these polymers were much lighter in colour than those of the corresponding trimellitimide series. All polymers were readily soluble in a variety of organic solvents such as NMP, N,N‐dimethylacetamide, dimethyl sulfoxide, and even in the less polar m‐cresol and pyridine. Compared with those of corresponding ODPA–MDA polyimide, the solubilities of poly(amide–imide–imide)s III_a–j were greatly improved. Polymers III_a–j afforded tough, transparent, and flexible films, which had tensile strengths ranging from 82 to 105 MPa, elongations at break from 8 to 14%, and initial moduli from 2.0 to 2.2 GPa. The glass transition temperature of polymers were recorded at 255–288 °C. They had 10% weight loss at a temperature above 540 °C and left more than 60% residue even at 800 °C in nitrogen. © 2002 Society of Chemical Industry     

Synthesis and properties of novel soluble aromatic polyamides containing 4-aryl-2,6-diphenylpyridine moieties and pendant fluorinated phenoxy groups

Three diamine monomers containing pyridine groups were prepared via the modified Chichibabin reaction of aromatic aldehydes with 4′-nitroacetophenone, followed by reduction with hydrazine hydrate in the presence of Pd/C. Novel aromatic polyamides containing 4-aryl-2,6-diphenylpyridine moieties and pendant fluorinated phenoxy groups were synthesized from these diamines and two fluorinated isophthaloyl dichlorides by the low temperature solution polycondensation in N,N-dimethylacetamide (DMAc). All the polymers are amorphous and readily soluble in strong polar organic solvents such as DMAc, N-methyl-2-pyrrolidinone (NMP), N,N-dimethylformamide (DMF), and dimethyl sulfoxide (DMSO) at room temperature. The resulting polymers showed glass transition temperatures between 270 and 314 °C and 5 % weight loss temperatures ranging from 442 °C to 475 °C, and char yields at 800 °C higher than 53 % in nitrogen. These polyamides could be cast into transparent, flexible and strong films from DMAc solution with tensile strengths of 72.5–87.3 MPa, tensile moduli of 2.35–2.87 GPa, and elongations at break of 5.3–9.5 %. The polyamide films exhibited low dielectric constants of 3.21–3.54 (1 MHz), low water uptakes in the range of 1.17–1.38 %, and high transparency with an ultraviolet-visible absorption cut-off wavelength in the 380–391 nm range.     

Synthesis and characterization of liquid crystalline ionomers with polymethylhydrosiloxane main-chain- and side-chain-containing sulfonic acid groups

A novel thermotropic side-chain liquid crystalline ionomer (LCI) containing sulfonic acid groups on the side-chain was synthesized by graft copolymerization of mesogenic monomer 4-allyloxy-benzoxy-4′-methoxyphenyl (ABM) and nonemesogenic monomer 4-allyloxy-azobenzene sulfonic acid (AABS) upon polymethylhydrosiloxane (PMHS). The chemical structures of the polymers were confirmed by IR spectroscopy. DSC and TGA were used to measure the thermal properties of those polymers and the mesogenic properties were characterized by polarized optical micrography (POM), DSC, and WAXD. The clearing point temperature (T_c) of these liquid crystalline ionomers was enhanced 50–60°C compared with the polymer without ionic groups. The LCIs exhibit a broad smectic mesogenic region of 80–90°C; the thermal stability below 200°C of the polymers decreases with increasing sulfonic acid concentration. The inherent viscosity of 0.5% solutions decreased with increasing sulfonic acid concentration in the polymer chains. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1555–1561, 1998     

Synthesis and characterization of organosoluble poly(arylate‐imide)s prepared from direct polycondensation of bis(trimellitimide)‐diacids and various bisphenols

Three diimide‐diacids, 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane ( I‐A ), 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]propane ( I‐B ), and 5,5′‐bis[4‐ (4‐trimellitimidophenoxy)phenyl]hexahydro‐4,7‐methanoindan ( I‐C ), were prepared by the azeotropic condensation of trimellitic anhydride with three analogous diamines. Three series of alternating aromatic poly(arylate‐imide)s, having inherent viscosities of 0.41–0.82 dL/g, were synthesized from these diimide‐diacids ( I‐A , I‐B , and I‐C ) with various bisphenols by direct polycondensation using diphenyl chlorophosphate and pyridine as condensing agents. All of the polymers were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, and even in the less polar tetrahydrofuran. These polymers could be cast into transparent and tough films, which had strength at break values ranging from 73 to 98 MPa, elongation at break from 6 to 11%, and initial modulus from 1.6 to 2.2 GPa. The softening temperatures of the polymers were recorded at 145–248°C. They had 10% weight loss at a temperature above 450°C and left 35–51% residue even at 800°C in nitrogen. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3818–3825, 2003     

Synthesis and properties of new aromatic poly(ester‐imide)s derived from 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl) pyridine and various dihydroxy compounds

A novel class of wholly aromatic poly(ester‐imide)s, having a biphenylene pendant group, with inherent viscosities of 0.32–0.49 dL g^?1 was prepared by the diphenylchlorophosphate‐activated direct polyesterification of the preformed imide‐ring‐containing diacid, 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine (1) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A reference diacid, 2,6‐bis(trimellitimido)pyridine (2) without a biphenylene pendant group and two phenylene rings in the backbone, was also synthesized for comparison purposes. At first, with due attention to structural similarity and to compare the characterization data, a model compound (3) was synthesized by the reaction of compound 1 with two mole equivalents of phenol. Moreover, the optimum condition of polymerization reactions was obtained via a study of the model compound synthesis. All of the resulting polymers were characterized by Fourier transform infrared and ¹H NMR spectroscopy and elemental analysis. The ultraviolet λ_max values of the poly(ester‐imide)s were also determined. All of the resulting polymers exhibited excellent solubility in common organic solvents, such as pyridine, chloroform, tetrahydrofuran, and m‐cresol, as well as in polar organic solvents, such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide. The crystalline nature of the polymers obtained was evaluated by means of wide‐angle X‐ray diffraction. The resulting poly(ester‐imide)s showed nearly an amorphous nature, except poly(ester‐imide) derived from 4,4′‐dihydroxy biphenyl. The glass transition temperatures (T_g) of the polymers determined by differential scanning calorimetry thermograms were in the range 298–342 °C. The 10% weight loss temperatures (T_10%) from thermogravimetric analysis curves were found to be in the range 433–471 °C in nitrogen. Films of the polymers were also prepared by casting the solutions. Copyright © 2006 Society of Chemical Industry     

Synthesis and characterization of novel polyaspartimides derived from 2,2′‐dimethyl‐4,4′‐bis(4‐maleimidophenoxy)biphenyl and various diamines

A novel bismaleimide, 2,2′‐dimethyl‐4,4′‐bis(4‐maleimidophenoxy)biphenyl, containing noncoplanar 2,2′‐dimethylbiphenylene and flexible ether units in the polymer backbone was synthesized from 2,2′‐dimethyl‐4,4′‐bis(4‐aminophenoxy)biphenyl with maleic anhydride. The bismaleimide was reacted with 11 diamines using m‐cresol as a solvent and glacial acetic acid as a catalyst to produce novel polyaspartimides. Polymers were identified by elemental analysis and infrared spectroscopy, and characterized by solubility test, X‐ray diffraction, and thermal analysis (differential scanning calorimetry and thermogravimetric analysis). The inherent viscosities of the polymers varied from 0.22 to 0.48 dL g⁻¹ in concentration of 1.0 g dL⁻¹ of N,N‐dimethylformamide. All polymers are soluble in N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethylsulfoxide, pyridine, m‐cresol, and tetrahydrofuran. The polymers, except PASI‐4, had moderate glass transition temperature in the range of 188°–226°C and good thermo‐oxidative stability, losing 10% mass in the range of 375°–426°C in air and 357°–415°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 279–286, 1999     

Synthesis and characterization of new polyamides containing p‐phenylenediacryloyl moieties in the main chain

Six new polyamides 8a–f containing p‐phenylenediacryloyl moieties in the main chain were prepared by the direct polycondensation reaction of bis(p‐amidobenzoic acid)‐p‐phenylene diacrylic acid 6 with 1,4‐diphenylene diamine 7a , 1,3‐diamino toluene 7b , 1,5‐diamino naphthalene 7c , 4,4′‐diamino diphenyl ether 7d , 4,4′‐diamino diphenyl sulfone 7e , and 3,3′‐diamino diphenylsulfone 7f by using thionyl chloride, N‐methyl‐2‐pyrolidone, and pyridine as condensing agents. These new polymers 8a–f were obtained in high yield and inherent viscosity between 0.35–0.65 dL/g. The resulting polyamides were characterized by elemental analysis, viscosity measurements, thermal gravimetric analysis (TGA and DTG), solubility test, FTIR and UV–vis spectroscopy. Diacid acid 6 as a new monomer containing p‐phenylenediacryloyl moiety was synthesized by using a three‐step reaction. First, p‐phenylenediacrylic acid 3 was prepared by reaction of terephthal aldehyde 1 with malonic acid 2 in the presence of pyridine, then diacid 3 was converted to p‐phenylenediacryloyl chloride 4 by reaction with thionyl chloride. Finally, bis(p‐amidobenzoic acid)‐p‐phenylene diacrylic acid 6 was prepared by the condensation reaction of phenylenediacryloyl chloride 4 with p‐aminobenzoic acid 5 . © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

High‐optical transparency and low‐dielectric constant of new organosoluble polyamides containing trifluoromethyl and xanthene groups

A series of fluorinated polyamides was prepared directly by low‐temperature polycondensation of a new cardo diacid chloride, 9,9‐bis[4‐(4‐chloroformylphenoxy)phenyl]xanthene (BCPX), with various diamines containing trifluoromethyl substituents in N,N‐dimethylacetamide (DMAc). Almost all polyamides showed excellent solubility in amide‐type solvents such as DMAc and could also be dissolved in pyridine, m‐cresol, and tetrahydrofuran. These polymers had inherent viscosities between 0.77 and 1.31 dL g^?1, and their weight‐average molecular weights and number‐average molecular weights were in the range of 69,000–102,000 and 41,000–59,000, respectively. The resulting polymers showed glass transition temperatures between 240–258°C and 10% weight loss temperatures ranging from 484°C to 517°C and 410°C to 456°C in nitrogen and air, respectively, and char yields at 800°C in nitrogen higher than 55%. All polymers were amorphous and could be cast into transparent, light‐colored, and flexible films with tensile strengths of 81–100 MPa, elongations at break of 8–12%, and tensile modulus of 1.6–2.1 GPa. These polymers had low‐dielectric constants of 3.34–3.65 (100 kHz), low‐moisture absorption in the range of 0.76–1.91%, and high transparency with an ultraviolet–visible absorption cut‐off wavelength in the 322–340 nm range. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of fluorine and nitrile containing polyimides

A series of polyimides were synthesized from new diamine, Bis [4,4′‐amino‐5,5′ trifluoromethyl phenoxy‐(hexafluoro isopropylidine) phenoxy phenyl] benzonitrile [BATFB] and various aromatic tetracarboxylic anhydrides by thermal and chemical imidization routes. The BATFB was synthesized in two steps by nucleophilic displacement reaction of 2,6‐dichloro benzonitrile, 4,4′‐(hexafluoro isopropylidine) diphenol and 2‐amino‐5‐fluoro benzotrifluoride in the presence of anhydrous potassium carbonate in N,N′‐dimethyl acetamide (DMAc) and the structure was confirmed by FTIR spectroscopy and CHNSO analyzer. The polymers were characterized by FTIR spectroscopy and thermal analysis were performed by differential scanning calorimetry and thermogravimetric analysis methods. The prepared polyimides had glass transition temperatures between 230 and 290°C and their 10% weight loss were recorded in the range 550–590°C in N₂ atmosphere. Majority of polymers are found to be soluble in most of the organic solvents such as DMSO, DMF, DMAc, m‐cresol, and THF even at room temperature and few becomes soluble on heating. The prepared polyimides showed water uptake values 0.34–0.54 wt % at room temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3455–3461, 2006