有机物在离子液体中无限稀释活度因子及液液界面张力的定量机构-性质关系

用PM3半经验量子化学方法计算了烷烃、烯烃和芳烃等的疏水性参数lgP、偶极矩、前线分子轨道能隙和水合能等结构描述符,与实验测定的烃类在1-丁基-3-甲基咪唑六氟磷酸盐（［C₄MIM］［PF₆］）、1-烯丙基-3-甲基咪唑四氟硼酸盐（［AMIM］［BF₄］）、1-异丁烯基-3-甲基咪唑四氟硼酸盐（［MPMIM］［BF₄］）和［MPMIM］［BF₄］-AgBF₄ 4种离子液体中的无限稀释活度因子进行定量结构-性质关系（QSPR）研究,建立的QSPR模型具有良好的关联和预测能力.同时测定了烃类等溶质与离子液体［C₄MIM］［PF₆］的液液界面张力,发现其与无限稀释活度因子有相似的变化趋势,据此采用同样的结构描述符,建立了溶质与［C₄MIM］［PF₆］界面张力的QSPR模型,模型的关联能力良好.     

Physical and electrochemical properties of 1-butyl-3-methylimidazolium bromide, 1-butyl-3-methylimidazolium iodide,and 1-butyl-3-methylimidazolium tetrafluoroborate

The density, viscosity, refractive index, heat capacity, heat of dilution, ionic conductivity, and electrochemical stability of 1-butyl-3-methylimidazolium bromide ([bmim][Br]), 1-butyl-3-methylimidazolium iodide ([bmim][I]), and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]) were measured at room temperature or over a temperature range of 293.2 to 323.2 K. The density and refractive index values of [bmim][I] appeared to be the highest among three ionic liquids (ILs). However, the experimental viscosity values of [bmim][Br] were higher than those of [bmim][BF₄], while the heat capacities and heats of dilution of [bmim][BF₄] were higher than those of [bmim][Br]. The cyclic voltammogram of [bmim][br] and [bmim][BF₄] indicated electrochemical windows in the stability range from 2.7 V of [bmim][[Br] to 4.7 V of [bmim][BF₄].     

Novel ionic liquids as reaction medium for ATRP of acrylonitrile in the absence of any ligand

Atom transfer radical polymerization (ATRP) of acrylonitrile (AN) with ethyl 2-bromoisobutyrate (EBiB) as the initiator was firstly approached in the absence of any ligand in three novel ionic liquids, 1-methylimidazolium acetate ([mim][AT]), 1-methylimidazolium valerate ([mim][VT]) and 1-methylimidazolium caproate ([mim][CT]), respectively. All the polymerizations in the ionic liquids proceeded in a well-controlled manner. The polymerization in [mim][AT] not only showed the best control of molecular weight and its distribution but also provided a rather rapid reaction rate with the molar ratio of [AN]:[FeBr₂]:[EBiB] at 200:2:1. The resulting polyacrylonitrile was successfully used as the macroinitiator to proceed the chain extension polymerization in [mim][AT]. After simple purification, all the ionic liquids and FeBr₂ could be recycled and reused and had no effect on the living nature of polymerization.     

含离子液体乙腈-正丙醇体系的等压汽液平衡

常压(101.3 kPa)下, 测定了如下体系的汽液平衡数据:乙腈-正丙醇-氯化1-苄基-3-甲基咪唑([BzMIM][Cl])、乙腈-正丙醇-溴化1-苄基-3-甲基咪唑([BzMIM][Br])、乙腈-正丙醇-溴化1-己基-3-甲基咪唑([HMIM][Br]), 考察了3种离子液体对乙腈-正丙醇体系相平衡行为的影响。实验结果表明, 3种离子液体都能够提高乙腈对正丙醇的相对挥发度, 3种离子液体提高相对挥发度的顺序为 [BzMIM][Cl] > [BzMIM][Br] > [HMIM][Br]。用NRTL模型对测得的汽液平衡数据进行了关联, 关联结果与实验结果具有良好的一致性。     

新型离子液体用于芳烃、烯烃与烷烃分离的初步研究

The separation of aromatic hydrocarbons or olefins from paraffins is very important in chemical industry. The volatile organic solvents used are usually harmful to environment and human health. As green solvents, room temperature ionic liquids are potential substitutes for the separation of hydrocarbon products. Activity coefficients at infinite dilution of hydrocarbon solutes, such as alkanes, hexenes,alkylbenzenes and styrene, in 1-butyl-3-methyl imidazolium hexafluorophosphate ( [BMIM] [PF6]), 1-allyl-3-methylimidazolium tetrafluoroborate ( [AMIM] [BF4] ), 1-isobutenyl-3-methylimidazolium tetrafluoroborate ( [MPMIM] [BF4]) and [MPMIM] [BF4] AgBF4 were determined by gas-liquid chromatography. The measurements were carried out at different temperatures between 298.15 K and 318. 15 K. The separation effects of these ionic liquids for olefin/paraffin, alkanes/benzene and hexene isomers were discussed.     

Extractive Desulfurization of Fuel Oils with Thiazolium-Based Ionic Liquids

A new class of green solvents, known as ionic liquids (ILs), has recently been the subject of intensive research on the extractive desulfurization of fuel oils because of the limitation of the traditional hydrodesulfurization method in catalytically removing thiophenic sulfur compounds. In this work, four thiazolium-based ILs, that is, 3-butyl-4-methylthiazolium dicyanamide ([BMTH][DCA]), 3-butyl-4-methylthiazolium thiocyanate ([BMTH][SCN]), 3-butyl-4-methylthiazolium hexafluorophosphate ([BMTH][PF₆]), and 3-butyl-4-methylthiazolium tetrafluoroborate ([BMTH][BF₄]), are synthesized. The extractive capability of these ILs in removing thiophene (TS) and dibenzothiophene (DBT) from model fuel oils is investigated. [BMTH][DCA] and [BMTH][SCN] present better extractive desulfurization capability than [BMTH][BF₄] and [BMTH][PF₆], which may be ascribed to the additional π?π interaction between –C≡N (in [BMTH][DCA] and [BMTH][SCN]) and thiophenic ring (in TS and DBT); DBT in diesel fuel is more efficiently extracted than TS in gasoline. [BMTH][DCA] offers the best desulfurization results, where 64% and 45% sulfur removal are obtained for DBT and TS, respectively, at IL:oil mass ratio of 1:1, 25°C, 20 min. [BMTH][DCA] is thus selected to systematically investigate the effects of temperature, IL:oil mass ratio, initial sulfur content, multiple-extraction, and IL regeneration on desulfurization. The mutual solubility of [BMTH][DCA] with fuel oil is also determined. It is observed that the desulfurization capability is not too sensitive to temperature and initial sulfur content, which is desired in industrial application; the sulfur contents in gasoline and diesel fuel are reduced from 558 ppm to 20 ppm (after 5 cycles) and from 547 ppm to 8 ppm (after 4 cycles), respectively. This work may show a new option for deep desulfurization of fuel oils.     

Novel homogeneous gel fibers and capillaries from blend of titanium tetrabutoxide and siloxane functionalized ionic liquid

The preparation of ionogels by sol–gel processing has attracted much attention, because the final ceramic materials combine properties of both inorganic matrix (thermal and mechanical stability) and the ionic liquid (ionic conductivity). The aim of this study was to combine different imidazolium based ionic liquids (1-ethyl-3-methylimidazolium tetrafluoroborate [EMIM][BF₄], 1-butyl-3-methyl imidazolium tetrafluoroborate [BMIM][BF₄], 1-decyl-3-methylimidazolium tetrafluoroborate [DMIM][BF₄] and 1-methyl-3-[3′-(triethoxysilyl)propyl]imidazolium chloride MTICl) with titanium(IV) butoxide to prepare homogenous hybrid fibers through aqueous sol–gel reaction. The study showed that ionic liquid miscibility with metal alkoxide plays an important role in the preparation of homogenous fibers. Unlike simple imidazolium salts functionalized ionic liquid was dispersed homogenously in fibers, but the main advantage is derived from its chemical structure. New stable ionic liquid can be involved in sol–gel processes through ethoxy groups and as a result it associates with titanium alkoxide network by covalent bonding providing non-leaking ceramic hybrid material. Indirect and direct characterization studies of the product were carried out by energy-dispersive X-ray spectroscopy (EDX), silicon-29 nuclear magnetic resonance spectroscopy (²⁹Si NMR), scanning electron microscopy (SEM) and optical microscopies; also infrared spectra (IR) were recorded. Thermal analyses were performed by differential scanning calorimetry (DSC).     

Extractive Desulfurization of Fuel Oils with Dicyano(nitroso)methanide-based Ionic Liquids

The inability of traditional hydrodesulfurization (HDS) to effectively remove aromatic sulfur compounds such as thiophene (TS) and dibenzothiophene (DBT) has called for alternative methods to be studied, among which extractive desulfurization using ionic liquids (ILs) has attracted increasing interest. In this work, we prepared a new IL, 1-butyl-3-methylimidazolium dicyano(nitroso)methanide ([C₄mim][dcnm]), and investigated its extractive desulfurization for both model oils and real FCC gasoline, where model diesel fuel was composed of n-hexane and droplets of DBT and model gasoline was composed of n-hexane, toluene and droplets of TS. Other three [dcnm]-based ILs, 1-ethyl-3-methylimidazolium dicyano(nitroso)methanide ([C₂min][dcnm]), N-ethyl-N-methylpyrrolidinium dicyano(nitroso)methanide ([C₂mpyr][dcnm]), and N-butyl-N-methylpyrrolidinium dicyano(nitroso)methanide ([C₄mpyr][dcnm]), were also comparatively investigated. These [dcnm]-based ILs have low viscosity which favors the mass transfer and reduces the extractive equilibrium time, also are fluorine-free which avoids the corrosion by hydrogen fluoride from anion decomposition that occurs generally in fluorine-containing ILs. The desulfurization ability follows the order [C₄min][dcnm] > [C₄mpyr][dcnm] > [C₂min][dcnm] > [C₂mpyr][dcnm]. Typically, [C₄min][dcnm] is capable of removing 66% DBT and 53% TS from their respective model oils after one cycle (initial 500 ppm S, 25°C, 15 min, mass ratio of IL:oil 1:1), and < 10 ppm S-content can be obtained after 4 cycles. It was observed interestingly that the S-content in real FCC gasoline can be reduced from initial 250 ppm to < 30 ppm after 6 cycles using [C₄min][dcnm] as extractive reagent, which is better than some previous results for real feedstocks. Mutual solubility, extractive temperature, IL:oil mass ratio, multiple extraction, initial S-content, and regeneration were also studied. These dcnm-based ILs are competitive extractive reagents compared with some other ILs to remove those aromatic S-compounds from fuel oils.     

Retention mechanism of some solutes using ionic liquids as mobile phase modifier in RP-high-performance liquid chromatography (HPLC)

Two kinds of ionic liquid, 1-Hexyl-3-methylimidazolium tetrafluoroborate ([Hmim][BF₄]) and 1-Methyl-3-octylimidazolium tetrafluoroborate ([Omim][BF₄]), were used as additives in the linear solvation energy relationships (LSERs) model to investigate the fundamental chemical interactions governing the retention of nine aromatic compounds in acetonitrile/water mobile phases on a C₁₈ column. The effects of the [Hmim][BF₄] and [Omim][BF₄] were compared and the ability of the LSERs to account for the chemical interactions underlying solute retention was shown. A comparison of predicted and experimental retention factors suggests that LSER formalism is able to reproduce adequately the experimental retention factors of the solutes studied in the different experimental conditions investigated.     

Aggregation Behavior of Imidazolium-Based Amino Acid Ionic Liquid Surfactants in Aqueous Solution: The Effect of Amino Acid Counterions

Three kinds of imidazolium-based amino acid ionic liquid surfactants (AAILS), 1-tetradecyl-3-methylimidazolium _L-aminopropionic acid salt ([C₁₄mim][Ala]), 1-tetradecyl-3-methylimidazolium _L-2-pyrrolidinecarboxylic acid salt ([C₁₄mim][Pro]), and 1-tetradecyl-3-methylimidazolium _L-aminohydrocinnamic acid salt ([C₁₄mim][Phe]), were synthesized by employing natural amino acids as counterions. Their adsorption and self-aggregation behaviors in aqueous solution were investigated systematically by means of surface tension and electrical conductivity measurements. Surface tension results indicate that surface properties and micellization behavior of AAILS are significantly affected by counterions. The micellization of [C₁₄mim][Pro] and [C₁₄mim][Phe] is entropy-driven at low temperatures but enthalpy-driven at high temperatures, whereas [C₁₄mim][Ala] is enthalpy-driven throughout the whole temperature range, owing to the variation in hydrophobicity and size of amino acid counterions. The surface activity of [C₁₄mim][Phe] is superior to that of conventional imidazolium-based ionic liquid surfactants with the same hydrocarbon chain length, 1-tetradecyl-3-methylimidazolium bromide (C₁₄mimBr), indicating that the aromatic counterion can promote the micellar formation process.     

An investigation of silver electrodeposition from ionic liquids: Influence of atmospheric water uptake on the silver electrodeposition mechanism and film morphology

The electrodeposition of silver from two ionic liquids, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF₄]) and N-butyl-N-methyl-pyrrolidinium bis(trifluoromethanesulfonyl)imide ([C₄mPyr][TFSI]), and an aqueous KNO₃ solution on a glassy carbon electrode was undertaken. It was found by cyclic voltammetry that the electrodeposition of silver proceeds through nucleation–growth kinetics. Analysis of chronoamperometric data indicated that the nucleation–growth mechanism is instantaneous at all potentials in the case of [BMIm][BF₄] and [C₄mPyr][TFSI], and instantaneous at low overpotentials tending to progressive at high overpotentials for KNO₃. Significantly, under ambient conditions, the silver electrodeposition mechanism changes to progressive nucleation and growth in [C₄mPyr][TFSI], which is attributed to the uptake of atmospheric water in the IL. It was found that these differences in the growth mechanism impact significantly on the morphology of the resultant electrodeposit which is characterised ex situ by scanning electron microscopy and X-ray diffraction.     

Complete conversion of cellulose to water soluble substances by pretreatment with ionic liquids

Pretreatment of cellulose to water soluble substances (WSS) can enhance its efficient conversion in water solvent, such as ethanol fermentation. In this work, we found ionic liquid (IL), 1-methyl-3-methylimidazolium dimethylphosphate ([Mmim][DMP]), could convert efficiently cellulose to obtain WSS, and the product WSS and IL mixture could be separated by ethanol anti-solvent way. Effects of ILs, time, temperature and water on cellulose conversion were investigated. NMR, FTIR, XRD and SEM were employed to study the mechanism of cellulose conversion with ILs. The results indicate that [Mmim][DMP] has a greater ability to interact with cellulose than [Bmim][Cl] under the same conditions. Cellulose can be completely converted into WSS in [Mmim][DMP] under all the investigated temperatures from 140 to 160 °C. Increasing temperature is beneficial to the conversion rate of cellulose. But the presence of water can decrease the conversion rate of cellulose. During the treatment by [Mmim][DMP], the hydroxyls of cellulose can form hydrogen bonds with both anion and cation of [Mmim][DMP], and after the treatment the inter- and intramolecular hydrogen bonds of cellulose and the compact structure of cellulose are collapsed.     

Physical and electrochemical properties of lithium-doped 1-butyl-3-methylimidazolium salts

Two well known room temperature ionic liquids (RTILs), 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF₄]) and 1-butyl-3-methylimidazolium iodide ([BMIm][I]), were synthesized. Their physical properties such as reflective indices, densities, viscosities, heat capacities, and heats of dilution were measured. The overall properties of [BMIm][BF₄] obtained after two-step reactions were superior to those of the IL with a halide anion. The incorporation of lithium ions using lithium tetrafluoroborate (LiBF₄) in each IL was carried out and ionic conductivities as a function of temperature and Li ion concentration were investigated. The isothermal conductivity graph showed a parabolic curve shape suggesting that the maximum values exist at a specific concentration condition while they continuously increased as the temperature increased. The conductivities reached as high as 10⁻³ S·cm⁻¹.     

Cu(I)-Based Ionic Liquids as Potential Absorbents to Separate Propylene and Propane

The absorption of propylene and propane in Cu(I)-based ionic liquids, i.e., 1-butyl-3-methylimidazolium chloride/CuCl ([Bmim][Cl]/CuCl), N-Methyl pyrrolidone chloride/CuCl ([HNMP][Cl]/CuCl), and tricaprylmethylammonium thiocyanate/CuSCN ([A336][SCN]/CuSCN), are investigated in this work. It is observed that such Cu(I)-based ionic liquids, especially Bmim-based ionic liquids, present good absorption capability for propylene and good selectivity over propane, e.g., 1.0 kilogram [Bmim][Cl]/CuCl is able to absorb 0.08 mol propylene while only 0.006 mol propane at 25°C and 1.3 bar with the selectivity of 13. The effects of pressure, Cu⁺ concentration, and temperature on the absorption are investigated; in addition, the absorption kinetics of propylene by [Bmim][Cl]/CuCl is obtained. The much higher absorption capability for propylene than propane is ascribed to the π-complexation between propylene and Cu⁺. This work shows that the absorption by Cu(I)-based ionic liquids is an potential alternative method for traditional cryogenic distillation with high energy cost to separate propylene and propane.     

Raman Microscopic Study of Japanese Beech (Fagus crenata) As Treated with the Ionic Liquid, 1-Ethyl-3-Methylimidazolium Chloride

The chemical changes in various morphological regions of Japanese beech (Fagus crenata) upon treatment with the ionic liquid 1-ethyl-3-methylimidazolium chloride ([C2mim][Cl]), which preferentially dissolves cellulose, have been investigated by Raman microscopy. The reactivity of polysaccharides and lignin with [C2mim][Cl] differed depending on the types of wood tissues. Chemical components in parenchyma cells showed higher resistance to degradation upon [C2mim][Cl] treatment than wood fiber and vessel. In addition, the lignin structure was partially degraded or modified by [C2mim][Cl] treatment, and its binding mode was complicated; nevertheless, lignin was stable in [C2mim][Cl].     

Thermal and electrochemical properties of morpholinium salts with bromide anion

The present work is a study of the thermal properties and electrochemical stabilities of N-ethyl-N-methylmorpholinium bromide ([Mor_1,2][Br]), N-butyl-N-methylmorpholinium bromide ([Mor1_1,4][Br]), N-octyl-N-methylmorpholinium bromide ([Mor1_1,8][Br]), N-dodecyl-N-methylmorpholinium bromide ([Mor1_1,12][Br]), and N,N-dihydroxyethylmorpholinium bromide ([DHEMor][Br]). The melting points, decomposition temperatures, and electrochemical stabilities of the salts were measured by DSC (differential scanning calorimetry), TGA (thermogravimetric analysis), and CV (cyclic voltammogram), respectively. All salts were decomposed below approximately 230.00 °C and their melting points were above 100.00 °C except [DHEMor][Br], which melted at 75.17 °C. [DHEMor][Br] appeared to possess the most wide liquid-phase range between melting point and decomposition temperature. The electrochemical windows of salts ranged from 3.3 V for [Mor_1,8][Br] to 3.6 V for [Mor_1,4][Br] and thus did not show any noticeable variation with cations used for salt synthesis.     

Critical properties and acentric factors of ionic liquids

Since most ionic liquids (ILs) decompose before reaching their critical state, the experimental measurement of their critical properties are not possible. In this study, the critical temperatures, critical pressures and acentric factors of ten commonly investigated ILs were determined by making an optimum fit of the calculated vapor-liquid equilibrium data of binary mixtures of CO₂+IL to the experimental values found in literature. For this purpose, the Peng-Robinson equation of state (PR EoS) and the differential evolution optimization method were used. The ILs considered were 1-ethyl-3-methylimidazolium hexafluorophosphate ([emim][PF₆]), 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([emim][Tf₂N]), 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]), 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([bmim][Tf₂N]), 1-hexyl-3-methylimidazolium tetrafluoroborate ([hmim][BF₄]), 1-hexyl-3-methylimidazolium hexafluorophosphate ([hmim][PF₆]), 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([hmim][Tf₂N]), 1-octyl-3-methylimidazolium tetrafluoroborate ([omim][BF₄]) and 1-octyl-3-methylimidazolium hexafluorophosphate ([omim][PF₆]). To evaluate the ability of the determined parameters in predicting the phase behavior of systems other than the systems that were used for parameter optimization, both sets of parameters obtained in this work and that of Valderrama et al. were used to predict bubble-point pressures of CHF₃+[bmim][PF₆] (by using the PR EoS and the Soave-Redlich-Kwong equation of state. The bubble-point pressures of CO₂+IL systems optimized in this study by the PR EoS were also determined using the Soave-Redlich-Kwong equation of state (SRK EoS). In addition, liquid densities of pure ILs were predicted using a generalized correlation proposed by Valderrama and Abu-Shark. In all cases, the various predicted properties of these ten ILs, were in better agreement with the experimental data, using the critical properties and acentric factor obtained in this study, compared to the values suggested by Valderrama et al.     

Ionic liquids as entrainer in extractive distillation for effectively separating 1-propanol–water azeotropic mixture

Economically separating 1-propanol(NPA) from water is an emergent issue for producing pharmaceutical intermediates such as n-propyl acetate, n-propylamine and so on. In this work, fourionic liquids(ILs) 1-ethyl-3-methylimidazolium thiocyanate([EMIM][SCN]), 1-butyl-3-methylimidazolium tetrafluoroborate([BMIM][BF₄]), 1,3-dimethylimidazolium methylsulfate([MMIM][MS]), 1,3-dimethylimidazolium dimethylphosphate([MMIM][DMP]) were introduced as potential entrainers for separating NPA–water a...     

乙腈+水+离子液体等压汽液平衡测定与计算

采用改进的Ellis平衡蒸馏仪测定了乙腈+水+1-乙基-3-甲基咪唑磷酸二乙酯盐([EMIM][DEP])、乙腈+水+{1-乙基-3-甲基咪唑醋酸盐([EMIM][OAC])+[EMIM][DEP]}常压(101.3 kPa)等压汽液平衡(VLE)数据。实验结果表明，备选离子液体可促进水+乙腈混合物的分离并消除其共沸点。借助NRTL模型成功关联了含离子液体的三元和四元VLE实验数据，获得了乙腈-[EMIM][DEP]、水-[EMIM][DEP]和[EMIM][OAC]-[EMIM][DEP]二元交互作用参数。应用COSMO-SAC预测了实验VLE，结果令人满意。量化计算表明可与水形成强相互作用的离子液体更易促进乙腈与水的分离。     

Vapor pressure measurement and correlation of acetonitrile+1-butyl-3-methylimidazolium chloride,+1-butyl-3-methylimidazolium tetrafluoroborate,and+1-hexyl-3-methylimidazolium chloride

Vapor pressures were measured for acetonitrile+1-butyl-3-methylimidazolium chloride ([C4mim][Cl]),+1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim][BF4]) and+1-hexyl-3-methylimidazolium chloride ...