Laser-ablated plasma for deposition of ZnO thin films on various substrates

We report optical and structural properties of ZnO films deposited by pulsed laser deposition technique on 1100) n-typesilicon and quartz substrates at various pressures of back ground gas. ZnO plasma was created using KrF laser 1248 nm) atvarious pressures of the ambient gas, oxygen. Laser induced plasma at varying fluence on the target was investigated using optical emission spectroscopy and 2-D images of the expanding plumes. X-ray diffraction, atomic force microscopy, and spectro-photometry were used to characterize as grown films.     

等离子体化学气相沉积类金刚石碳膜的特性及应用

类金刚石（DLC）膜是含有sp^3杂化态的亚稳态非晶碳膜，是具有极高的硬度、化学稳定性和光学透明性的半导体材料。这篇综述介绍了用等离子体化学气相沉积DLC膜的沉积方法、所制备薄膜的特性及应用，最后展望了DLC膜的发展趋势。     

PECVD法低温制备二氧化硅薄膜(英文)

针对金属层间介质以及MEMS等对氧化硅薄膜的需求,介绍了采用等离子增强型化学气相沉积(PECVD)技术,以SiH4和N2O为反应气体,低温制备SiO2薄膜的方法.利用椭偏仪和应力测试系统对制得的SiO2薄膜的厚度、折射率、均匀性以及应力等性能指标进行了测试,探讨了射频功率、反应腔室压力、气体流量比等关键工艺参数对SiO2薄膜性能的影响.结果表明:SiO2薄膜的折射率主要由N2O/SiH4的流量比决定,而薄膜均匀性主要受电极间距以及反应腔室压力的影响.通过优化工艺参数,在低温260℃下制备了折射率为1.45～1.52、均匀性为±0.64%、应力在-350～-16MPa可控的SiO2薄膜.采用该方法制备的SiO2薄膜均匀性好、结构致密、沉积速率快、沉积温度低且应力可控,可广泛应用于集成电路以及MEMS器件中.     

Growth of GaN films on nitrided GaAs substrates using hot-wire CVD

Epitaxial growth of cubic-type gallium nitride (c-GaN) by hot-wire CVD on GaAs(100) substrates was investigated. Prior to the epitaxial growth, a nitridation layer was formed using ammonia plasma generated by electron cyclotron resonance (ECR). It was found that the crystal phase of the epitaxial layer was predominantly determined by that of the nitrided layer. The best nitridation condition using ECR plasma for the growth of the GaN films with preponderant cubic-type structure was obtained.     

Growth, characterization, and properties of nanographene

A systematic study on nanographene grown directly on silicon dioxide substrates is reported. The growth is carried out in a remote plasma-enhanced chemical vapor deposition system at a low temperature of around 550 °C with methane gas as the carbon source. Atomic force microscopy is used to characterize the nanographene morphology, and Raman spectroscopy, X-ray photoelectron spectroscopy, and scanning tunneling microscopy are exploited to identify the in-plane sp(2) bonding structures of nanographene samples. Electrical transport properties are measured at various temperatures down to 4 K. Tunneling effects, minimal conductance at the charge-neutral point, sheet resistances, and Dirac point position at different channel lengths are investigated. In addition, nanographene film possesses high transmittance properties, as indicated by transmittance spectra. Nanographene devices are fabricated from rippled structures, and show great promise for strain-gauge sensor applications.     

Amorphous and nanocrystalline silicon growth on carbon nanotube substrates

In this study, smooth and conformal hydrogenated silicon thin films are examined and analyzed on various multi-walled carbon nanotube (MWCNT) substrates. The films are deposited using radio-frequency plasma-enhanced chemical vapor deposition with He dilution and parameters that are heavily in the γ regime. It is proposed that high-energy plasmas with limited penetration depth can induce crystallization to occur on MWCNT substrates of varying active surface areas. The samples presented exhibit properties that are promising for energy applications, including photovoltaics and lithium-ion batteries and have been studied using scanning electron microscopy, Raman spectroscopy, X-ray diffraction, UV-Vis spectrophotometry, four-point probe measurements, and Fourier transform infrared spectroscopy.     

MOCVD方法在Si衬底上低温生长ZnO薄膜

采用二乙基锌(DEZn)和氧化亚氮(N2O)作为锌源和氧源,在低温300℃,利用金属有机化学气相沉积(MOCVD)的方法在Si(100)衬底上制备了ZnO薄膜.通过优化氧锌比,ZnO薄膜为高度单一c轴方向生长.由光致发光谱和反射谱得知,ZnO薄膜的紫外发光峰位于388nm,具有很好的光透性,且其PL谱半峰宽为80meV.     

掺硼非晶硅薄膜的微结构和电学性能研究

以硅烷(SiH4)和硼烷(B2H6)为气相反应先驱体，采用等离子体增强化学气相沉积法，(PECVD)制备出能应用于液晶光阀光导层的硼掺杂非晶氢硅薄膜。X射线衍射、原子力显微镜和光、暗电导测试表明，一定程度的硼掺杂提高了非晶氢硅薄膜的电导率、降低了非晶氢硅薄膜的光、暗电导比；硼掺杂促进薄膜晶态率的增加和硅晶粒尺寸的增大，薄膜的结晶状态将逐渐从非晶硅过渡到纳米硅，最后发展为多晶硅。红外吸收谱研究表明了大量的硼原子与硅、氢原子之间能形成某些形式的复合体，仅有少量硼元素对受主掺杂有贡献。     

Effects of oxygen on multiwall carbon nanotubes growth by PECVD

Multiwall carbon nanotubes (MWCNTs) were grown by dielectric barrier discharge (DBD)-type plasma enhanced chemical vapor deposition (PECVD) method in downstream. The temperature was 973 K and the compositions of gases were methane, hydrogen and oxygen in the total pressure of 0.05 MPa. The effect of O₂ concentration in the mixture on the configuration of carbon nanotubes (CNTs) was investigated in detail. Results from scanning electron microscope (SEM) and transmission electron microscope (TEM) showed that CNTs grown in CH₄/H₂ (38.6%/61.4%, volume) mixture have many defects and contained disordered graphitic materials. With the addition of appropriate amount of O₂ (∼0.67%), high-purity CNTs could be obtained. However, no CNT, even no carbon matrix existed under the condition of an excessive oxygen concentration (>1.0%, volume) in the mixture. In order to understand the role of O₂ during CNTs growth, optical emission spectroscopy (OES) was in-situ employed and the results predicted that the improvement of CNTs quality in O₂ addition was attributed to the effect of OH oxidation from the reaction of atomic oxygen with hydrogen in the plasma.     

The role of hydroxyl and atomic oxygen in multiwall carbon nanotube growth

Multiwall carbon nanotubes (CNTs) were grown by the plasma-enhanced chemical vapor deposition (PECVD) method in downstream on the p-Si (100) substrate. Besides precursors, methane as the carbon source and hydrogen as the ablation, oxygen or H₂O was alternatively inlet into the reactive chamber at the pressure of 0.05 MPa. Given characterizations of the tube structure and tube mass weight, the role of radical atomic O, hydroxyl and perhydroxyl in multiwall CNT growth was explored. In addition to a small amount of O₂ (∼0.67%) or H₂O (∼0.1%), it was found that a high quantity of pure nanotubes can be grown in the downstream. However, no nanotube could be formed or even the carbon matrix generated when the concentration of O₂ or H₂O exceeded a proper value in the mixture. The mechanism of multiwall CNT growth controlled by active radicals was explored in this paper.     

Characterization of a large area scanning PECVD deposition system with small size RF electrodes

We have conducted characterization of a scanning plasma enhanced chemical vapor deposition (PECVD) system for producing controlled non-uniform deposition or etching profiles. Both self-bias and plasma potential showed that the plasma conditions were disturbed significantly when the source was very close to the chamber wall but electron temperature and ion density were not affected significantly. It was found that a very thin but long tail of parasitic deposition was present over the entire large substrate. To eliminate the parasitic deposition an aperture (plasma guarding house) was constructed and was found to eliminate the parasitic plasma deposition. Deposited silicon nitride and silicon oxide thin films using the plasma guarding house in the scanning PECVD system showed very good optical properties similar to those obtained in conventional deposition methods. No multilayer structure was observed in TEM analysis on these films.     

甲烷浓度对金刚石薄膜质量的影响

纳米金刚石薄膜具有优异的性能,已在多个领域获得广泛应用.但微波等离子体化学气相沉积制备的金刚石薄膜质量却严重受沉积工艺的影响,为了深入了解沉积工艺对制备的金刚石薄膜质量的影响,本文详细研究了甲烷浓度对微波等离子体化学气相沉积( MPCVD)金刚石薄膜质量的影响,利用扫描电镜、X射线衍射、拉曼光谱以及原子力显微镜对其进行...     

PECVD法生长的氧化锡薄膜的结构与性能研究

非化学计量的二氧化锡是一种 n 型半导体材料,具有良好的光电特性。本文用等离子增强化学气相沉积(PECVD)法生长 SnO_(2-x)薄膜,并进行了生长条件与其结构和性能的研究。结果表明:不同的淀积条件,可以获得从多晶到非晶态不同结构、化学稳定性良好、可见光透射率高、具有不同电导率的 SnO_(2-x)薄膜材料。     

微波等离子体化学气相沉积技术制备金刚石薄膜的研究

介绍了微波等离子体化学气相沉积法（MPCVD）制备金刚石薄膜的研究情况，重点论述了该法的制备工艺对金刚石薄膜质量的影响及其制备金刚石薄膜的应用前景。     

热丝CVD法低温制备的多晶硅薄膜质量对衬底依赖性的研究

以SiH4和H2作为反应气体,采用HWCVD的方法分别在石英玻璃、AZO、Si（100）和Si（111）衬底上制备了多晶硅薄膜。利用X射线衍射（XRD）,拉曼（Raman）光谱和傅里叶红外（FT-IR）吸收光谱研究了不同衬底对多晶硅薄膜的择优取向、晶化率和应力的影响,用SEM观察了多晶硅薄膜的表面形貌。研究发现在4种衬底上生长的多晶硅薄膜均为（111）择优取向。单晶硅片对多晶硅薄膜有很强的诱导作用,并且Si（111）的诱导作用优于Si（100）的诱导作用。AZO对多晶硅薄膜生长也有一定的诱导作用。通过计算薄膜晶态比,得到除以石英为衬底的样品外,其它3种样品的晶态比均在90%以上,尤其以单晶硅片为衬底的样品更高。石英玻璃、AZO和Si（100）上生长的多晶硅薄膜中均存在压应力。     

Initiated chemical vapor deposition of polymer films on nonplanar substrates

Thin polymer films are deposited on nonplanar geometries via initiated chemical vapor deposition (iCVD). Films in microtrenches exhibit step coverage of 0.85 for the highest aspect ratio trench studied here. An analytical model shows that the sticking probability of the initiating radical is a function of monomer surface concentration and takes values between 1.1 × 10^− 2 and 5.0 × 10^− 2 for the conditions studied here. These results indicate that iCVD proceeds via reaction of a vapor phase initiating radical with a surface adsorbed monomer. The high degree of conformality allows iCVD to be used to create patterns with features less than 10 µm by physically masking the substrate.     

Fast and uniform growth of graphene glass using confined-flow chemical vapor deposition and its unique applications

Fast and uniform growth of high-quality graphene on conventional glass is of great importance for practical applications of graphene glass. We report herein a confined-flow chemical vapor deposition (CVD) approach for the high-efficiency fabrication of graphene glass. The key feature of our approach is the fabrication of a 2–4 μm wide gap above the glass substrate, with plenty of stumbling blocks; this gap was found to significantly increase the collision probability of the carbon precursors and reactive fragments between one another and with the glass surface. As a result, the growth rate of graphene glass increased remarkably, together with an improvement in the growth quality and uniformity as compared to those in the conventional gas flow CVD technique. These high-quality graphene glasses exhibited an excellent defogging performance with much higher defogging speed and higher stability compared to those previously reported. The graphene sapphire glass was found to be an ideal substrate for growing uniform and ultra-smooth aluminum nitride thin films without the tedious pre-deposition of a buffer layer. The presented confined-flow CVD approach offers a simple and low-cost route for the mass production of graphene glass, which is believed to promote the practical applications of various graphene glasses.

Open image in new window

     

柔性衬底铝掺杂氧化锌透明导电膜的特性研究

室温下采用射频磁控溅射法在有机薄膜－聚丙烯己二酯（polypropylene adipate,PPA)衬底上制备出了ZnO:Al(AZO)透明导电膜。其它制备参数保持不变的条件下通过改变淀积时间得到厚度不同的薄膜，并对不同厚度AZO薄膜的结构特性、光学特性和电学特性进行了研究。     

微波等离子体化学气相沉积法在硅片上同时生长碳化硅和金刚石

研究了衬底温度、核化密度、衬底表而预处理等工艺参数对微波等离子体化学气相沉积法在硅片上同时生长碳化硅和金刚石的影响.采用扫描电镜、X-射线衍射、喇曼光谱和红外光谱对样品进行了表征.结果表明:从高核化密度生长的金刚石膜中探测不到碳化硅;不论对硅衬底进行抛光预处理还是未抛光预处理,从低核化密度牛长的金刚石厚膜中总能探测到碳化硅.碳化硅生长在硅衬底上未被金刚石覆盖的地方,或者是在金刚石晶核之间的空洞处.碳化硅形成和金刚石生长是同时发生的两个竞争过程.此研究结果为制备金刚石和碳化砟复合材料提供了一种新的方法.     

等离子热丝化学气相沉积金刚石膜工艺参数研究

采用等离子热丝化学气相沉积(PHFCVD)装置进行了金刚石薄膜的制备实验。实验条件为：氢气流量为200sccm,甲烷流量为2～12sccm,基体温度为700～900℃,偏压为0～400V,真空室压力为4kPa。通过实验得出了甲烷含量、基体温度和偏压对沉积金刚石膜的影响,并运用扫描电子显微镜(SEM)、原子力显微镜(AFM)和X射线衍射(XRD)等测试方法对金刚石薄膜进行了观察分析。