Short wavelength (/spl lambda//spl sim/4.3 /spl mu/m) high-performance continuous-wave quantum-cascade lasers

We report continuous-wave (CW) operation of a 4.3-/spl mu/m quantum-cascade laser from 80 K to 313 K. For a high-reflectivity-coated 11-/spl mu/m-wide and 4-mm-long laser, CW output powers of 1.34 W at 80 K and 26 mW at 313 K are achieved. At 298 K, the CW threshold current density of 1.5 kA/cm/sup 2/ is observed with a CW output power of 166 mW and maximum wall-plug efficiency of 1.47%. The CW emission wavelength varies from 4.15 /spl mu/m at 80 K to 4.34 /spl mu/m at 298 K, corresponding to a temperature-tuning rate of 0.87 nm/K. The beam full-width at half-maximum values for the parallel and the perpendicular far-field patterns are 26/spl deg/ and 49/spl deg/ in CW mode, respectively.     

Ridge-width dependence on high-temperature continuous-wave quantum-cascade laser operation

We report continuous-wave (CW) operation of quantum-cascade lasers (/spl lambda/=6 /spl mu/m) up to a temperature of 313 K (40/spl deg/C). The maximum CW optical output powers range from 212 mW at 288 K to 22 mW at 313 K and are achieved with threshold current densities of 2.21 and 3.11 kA/cm/sup 2/, respectively, for a high-reflectivity-coated 12-/spl mu/m-wide and 2-mm-long laser. At room temperature (298 K), the power output is 145 mW at 0.87 A, corresponding to a power conversion efficiency of 1.68%. The maximum CW operating temperature of double-channel ridge waveguide lasers mounted epilayer-up on copper heatsinks is analyzed in terms of the ridge width, which is varied between 12 and 40 /spl mu/m. A clear trend of improved performance is observed as the ridge narrows.     

Low-threshold high-T/sub 0/ 1.3-/spl mu/m InAs quantum-dot lasers due to p-type modulation doping of the active region

P-type doping is used to demonstrate high-To, low-threshold 1-3 /spl mu/m InAs quantum-dot lasers. A 5-/spl mu/m-wide oxide confined stripe laser with a 700-/spl mu/m-long cavity exhibits a pulsed T/sub 0/ = 213 K (196 K CW) from 0/spl deg/C to 80/spl deg/C. At room temperature, the devices have a CW threshold current of /spl sim/4.4 mA with an output power over 15 mW. The threshold at 100/spl deg/C is 8.4 mA with an output power over 8 mW.     

High-Performance Continuous-Wave Operation of $lambda sim {hbox {4.6}}~mu{hbox {m}}$ Quantum-Cascade Lasers Above Room Temperature

We report the high-performance continuous-wave (CW) operation of 10-mum-wide quantum-cascade lasers (QCLs) emitting at lambda ~ 4.6mum, based on the GaInAs-AlInAs material without regrowth, in epilayer-up and -down bonding configurations. The operational characteristics of QCLs such as the maximum average power, peak output power, CW output power, and maximum CW operating temperature are investigated, depending on cavity length. Also, important device parameters, i.e., the waveguide loss, the transparency current density, the modal gain, and the internal quantum efficiency, are calculated from length-dependent results. For a high-reflectivity (HR) coated 4-mm-long cavity with epilayer-up bonding, the highest maximum average output power of 633 mW is measured at 65% duty cycle, with 469 mW still observed at 100%. The laser exhibits the maximum wall-plug efficiencies of 8.6% and 3.1% at 298 K, in pulsed and CW operatons, respectively. From 298 to 393 K, the temperature dependent threshold current density in pulsed operation shows a high characteristic temperature of 200 K. The use of an epilayer-down bonding further improves the device performance. A CW output power of 685 mW at 288 K is achieved for the 4-mm-long cavity. At 298 K, the output power of 590 mW, threshold current density of 1.52 kA/cm², and maximum wall-plug efficiency of 3.73% are obtained under CW mode, operating up to 363 K (90degC). For HR coated 3-mm-long cavities, laser characteristics across the same processed wafer show a good uniformity across the area of 21 cm², giving similar output powers, threshold current densities, and emission wavelengths. The CW beam full-width at half-maximum of far-field patterns are 25deg and 46deg for the parallel and the perpendicular directions, respectively.     

Low-threshold continuous-wave 1.5-/spl mu/m GaInNAsSb lasers grown on GaAs

We present the first continuous-wave (CW) edge-emitting lasers at 1.5 /spl mu/m grown on GaAs by molecular beam epitaxy (MBE). These single quantum well (QW) devices show dramatic improvement in all areas of device performance as compared to previous reports. CW output powers as high as 140 mW (both facets) were obtained from 20 /spl mu/m /spl times/ 2450 /spl mu/m ridge-waveguide lasers possessing a threshold current density of 1.06 kA/cm/sup 2/, external quantum efficiency of 31%, and characteristic temperature T/sub 0/ of 139 K from 10/spl deg/C-60/spl deg/C. The lasing wavelength shifted 0.58 nm/K, resulting in CW laser action at 1.52 /spl mu/m at 70/spl deg/C. This is the first report of CW GaAs-based laser operation beyond 1.5 /spl mu/m. Evidence of Auger recombination and intervalence band absorption was found over the range of operation and prevented CW operation above 70/spl deg/C. Maximum CW output power was limited by insufficient thermal heatsinking; however, devices with a highly reflective (HR) coating applied to one facet produced 707 mW of pulsed output power limited by the laser driver. Similar CW output powers are expected with more sophisticated packaging and further optimization of the gain region. It is expected that such lasers will find application in next-generation optical networks as pump lasers for Raman amplifiers or doped fiber amplifiers, and could displace InP-based lasers for applications from 1.2 to 1.6 /spl mu/m.     

Continuous-wave operation of GaInAs-AlGaAsSb quantum cascade lasers

We report on the demonstration of continuous-wave (CW) operation of GaInAs-AlGaAsSb quantum cascade (QC) lasers. By placing a 2.5-/spl mu/m-thick gold layer on both sides of the laser ridge to extract heat from the active region in the lateral direction, together with mounting the device epilayer down, we have achieved CW operation of GaInAs-AlGaAsSb QC lasers composed of 25 stages of active/injection regions. The maximum CW operating temperature of the lasers is 94 K, and the emission wavelength is around /spl lambda//spl sim/4.65 /spl mu/m. For a device with the size of 10/spl times/2000 /spl mu/m/sup 2/, the CW optical output power per facet is 13 mW at 42 K and 4 mW at 94 K. The CW threshold current density is 1.99 kA/cm/sup 2/ at 42 K, and 2.08 kA/cm/sup 2/ at 94 K, respectively.     

Type-II interband cascade lasers in the 4.3-4.7-/spl mu/m wavelength region

Operation of type-II interband cascade lasers in the 4.3-4.7-/spl mu/m wavelength region has been demonstrated at temperatures up to 240 K in pulsed mode. These lasers fabricated with 150-/spl mu/m-wide mesa stripes operated in continuous-wave (CW) mode up to a maximum temperature of 110 K, with an output power exceeding 30 mW/f and a threshold current density of about 41 A/cm/sup 2/ at 90 K. The maximum CW operation temperature of 110 K is largely limited by the high specific thermal resistance of the 150-/spl mu/m-wide broad area lasers. A 20-/spl mu/m-wide mesa stripe laser was able to operate in CW mode at higher temperatures up to 125 K as a result of the reduced specific thermal resistance of a smaller device.     

Improved CW operation of GaAs-based QC lasers: T/sub max/= 150 K

We present a substantial improvement in the CW performance of GaAs-based quantum cascade lasers with operation up to 150 K. This has been achieved through suitable changes in device processing of a well-characterized laser. The technology optimizes the current injection in the laser by reducing the size of the active stripe whilst maintaining a strong coupling of the optical mode to preserve low current densities. The reduction of total dissipated power is critical for these lasers to operate CW. At 77 K, the maximum CW optical power is 80 mW, threshold current is 470 mA, slope efficiency is 141 mW/A, and lasing wavelength /spl lambda//spl sim/10.3 /spl mu/m.     

Low threshold high-power room-temperature continuous-wave operation diode laser emitting at 2.26 /spl mu/m

Diode lasers emitting at 2.26 /spl mu/m, based on the InGaAsSb-AlGaAsSb materials system, are reported. These devices exhibit high internal quantum efficiency of 78% and low threshold current density of 184.5 A/cm/sup 2/ for a 2-mm-long cavity. Output power up to 700 mW (/spl ap/550 mW) has been obtained at 280 K (300 K) in continuous-wave operation with 100 /spl mu/m/spl times/1 mm lasers. These devices have been coated with an antireflection on the output facet and are mounted epilayer down on a copper block. The working temperature was maintained by a thermoelectric Peltier cooling element.     

Continuous-wave operation of terahertz quantum-cascade lasers

We report continuous-wave (CW) operation of a 4.4-THz quantum-cascade laser grown in the GaAs-AlGaAs materials system by molecular beam epitaxy. The device operates at 4 K with a threshold current of 160 mA, and an output power of /spl sim/25 /spl mu/W. In pulsed mode, the maximum operating temperature is 52 K, with a threshold current of 108 mA at 4 K. CW lasing was achieved by using a small cavity ridge area (60/spl times/600 /spl mu/m), and by coating one of the laser facets. These two features allowed for a substantial decrease of the threshold current and therefore reduced detrimental heating effects. The role played by the lateral resistance of the 800-nm GaAs layer underneath the active region was also investigated. Experimental data is presented showing that the temperature of the active region, which eventually hinders CW lasing, can be substantially influenced by the value of this lateral resistance.     

Low-temperature optimized vertical-cavity lasers with submilliamp threshold currents over the 77-370 K temperature range

We demonstrate an extended temperature range (77-370 K) of continuous wave (CW) operation for dielectrically-apertured double-intracavity-contacted vertical-cavity InGaAs strained QW lasers optimized for operation at cryogenic temperatures. Superior performance is achieved through the alignment of the cavity mode with the gain of the first and second quantized subbands at 77 K and room temperature, respectively. This design results in submilliamp threshold currents over a 77-370 K temperature range for 5.4-/spl mu/m diameter lasers. The threshold is 120 /spl mu/A and the output power is >8 mW at 77 K.     

Continuous-wave operation of GaInAsSb-GaSb type-II ridge waveguide lasers emitting at 2.8 /spl mu/m

We have realized compressively strained GaInAsSb-GaSb type-II double quantum-well lasers with an emission wavelength of 2.8 /spl mu/m. Using broad area devices, an internal absorption of 9.8 cm/sup -1/ and an internal quantum efficiency of 0.57 is determined. For the increase of the threshold current with temperature, a T/sub 0/ of 44 K is obtained. Narrow ridge waveguide lasers show continuous-wave laser operation at temperatures up to 45 /spl deg/C, with room-temperature (RT) threshold current of 37 mA. At RT, the maximum optical output power per facet of an uncoated 800/spl times/7 /spl mu/m/sup 2/ ridge waveguide laser exceeds 8 mW.     

Room-temperature continuous-wave laser operation of electrically-pumped 1.55 /spl mu/m VECSEL

A report is presented on room-temperature (RT) continuous-wave (CW) laser emission at 1.55 /spl mu/m of an all InP-based electrically-pumped vertical external-cavity surface-emitting laser (EP-VECSEL). Threshold currents of 1.4 kA/cm/sup 2/ and output powers of up to 0.3 mW were measured under CW operation at RT. A maximum output power of 2.7 mW has been obtained in quasi-CW operation at a heatsink temperature of 10.5/spl deg/C. This first result demonstrates that EP-VECSELs are a potential candidate for the realisation of compact vertical-cavity emitting sources.     

Vertical-cavity surface-emitting lasers in the 8-/spl mu/m midinfrared spectral range with continuous-wave and pulsed emission

Continuous-wave (CW) as well as pulsed-laser emission from a midinfrared (/spl lambda/=7.92 /spl mu/m) IV-VI vertical-cavity surface-emitting laser at 1.8 K is presented. The high-finesse microcavity, containing PbSe as an active medium, was optically pumped with a carbon monoxide laser at a wavelength of 5.28 /spl mu/m (1894 cm/sup -1/) in either CW or Q-switched mode. The maximum achieved CW power was 4.8 mW and pulsed peak powers were up to 23 W. Linewidths are considerably narrower than 0.10 cm/sup -1/, corresponding to 0.6 nm.     

Room-temperature low-threshold type-II quantum-well lasers at 4.5 /spl mu/m

We report optically pumped InAs-InGaSb-InAs-AlSb type-II quantum-well lasers at 3.84-4.48 /spl mu/m. Lasing was observed at temperatures up to 300 K with a characteristic temperature T/sub 0/ of 61.6 K. The average absorbed threshold power was only 0.7 mW at 220 K, and 2.7 mW at 300 K with a pulselength of 650 ns and a repetition rate of 2 kHz. At 49 K, the continuous-wave (CW) output power was 4.2 mW/facet with an absorbed threshold pump power of 31.5 mW and an absorbed pump power of 62 mW, indicating a differential quantum efficiency of 54% for two facets.     

Continuous-wave operation of quantum cascade laser emitting near 5.6 /spl mu/m

Buried heterostructure quantum cascade lasers emitting at 5.64 /spl mu/m are presented. Continuous-wave (CW) operation has been achieved at -30/spl deg/C for junction down mounted devices with both facets coated. A 750 /spl mu/m-long laser exhibited 3 mW of CW power with a threshold current density of 5.4 kA/cm/sup 2/.     

High-power ridge waveguide InGaAsN lasers fabricated with pulsed anodic oxidation

High-power InGaAsN triple-quantum-well strain-compensated lasers grown by metal-organic chemical vapor deposition were fabricated with pulsed anodic oxidation. A maximum light power output of 145 mW was obtained from a 4-/spl mu/m ridge waveguide uncoated laser diode in continuous-wave (CW) mode at room temperature. The devices operated in CW mode up to 130/spl deg/C with a characteristic temperature of 138 K in range of 20/spl deg/C-90/spl deg/C.     

Electrically pumped room temperature CW VCSELs with 2.3 /spl mu/m emission wavelength

Continuous wave (CW) operation at room temperature of electrically pumped InGaAlAs/InP vertical-cavity surface-emitting lasers (VCSELs) at emission wavelengths as high as 2.3 /spl mu/m is demonstrated for the first time. Devices with 15 /spl mu/m active region diameter show a maximum output power of 0.75 mW at 20/spl deg/C and a maximum CW operating temperature of 45/spl deg/C.     

MOVPE-grown GaInNAs VCSELs at 1.3 /spl mu/m with conventional mirror design approach

1.3 /spl mu/m oxide confined GaInNAs VCSELs designed using the same design philosophy used for standard 850 nm VCSELs is presented. The VCSELs have doped mirrors, with graded and highly doped interfaces, and are fabricated using production-friendly procedures. Multimode VCSELs (11 /spl mu/m oxide aperture) with an emission wavelength of 1287 nm have a threshold current of 3 mA and produce 1 mW of output power at 20/spl deg/C. The maximum operating temperature is 95/spl deg/C. Emission at 1303 nm with 1 mW of output power and a threshold current of 7 mA has been observed from VCSELs with a larger detuning between the gain peak and the cavity resonance.     

1.3-/spl mu/m Vertical-cavity surface-emitting lasers with double-bonded GaAs-AlAs Bragg mirrors

We demonstrate, for the first time, double-bonded AlGaInAs strain-compensated quantum-well 1.3-/spl mu/m vertical-cavity surface-emitting lasers (VCSELs). GaAs-AlAs Bragg mirrors were wafer-bonded on both sides of a cavity containing the AlGaInAs strain-compensated multiple-quantum-well active layers sandwiched by two InP layers. The lasers have operated under pulsed conditions at room temperature. A record low pulsed threshold current density of 4.2 kA/cm/sup 2/ and a highest maximum light output power greater than 4.6 mW have been achieved. The maximum threshold current characteristic temperature T/sub 0/ of 132 K is the best for any long wavelength VCSELs. The laser operated in a single-longitudinal mode, with a side-mode suppression ratio of more than 40 dB, which is the best results for 1.3-/spl mu/m VCSELs.