具有动态模式控制和斜波补偿的宽负载、多模式同步降压DC-DC转换器

A synchronous buck DC-DC converter with an adaptive multi-mode controller is proposed.In order to achieve high efficiency over its entire load range,pulse-width modulation(PWM),pulse-skip modulation(PSM) and pulse-frequency modulation(PFM) modes were integrated in the proposed DC-DC converter.With a highly accurate current sensor and a dynamic mode controller on chip,the converter can dynamically change among PWM, PSM and PFM control according to the load requirements.In addition,to avoid power device damage caused by inrush current at the start up state,a soft-start circuit is presented to suppress the inrush current.Furthermore,an adaptive slope compensation(SC) technique is proposed to stabilize the current programmed PWM controller for duty cycle passes over 50%,and improve the degraded load capability due to traditional slope compensation.The buck converter chip was simulated and manufactured under a 0.35μm standard CMOS process.Experimental results show that the chip can achieve 79%to 91%efficiency over the load range of 0.1 to 1000 mA.     

Design of high efficiency dual-mode buck DC-DC converter

A buck DC-DC switching regulator with high efficiency is implemented by automatically altering the modulation mode according to load current,and it can operate with an input range of 4.5 to 30 V.At light load current,the converter operates in skip mode.The converter enters PWM mode operation with increasing load current.It reduces the switching loss at light load and standby state,which results in prolonging battery lifetime and stand-by time.Meanwhile, externally adjustable soft-start minimizes the inru...     

一种带双重纹波补偿的10MHZ导通时间纹波控制降压型转化器

A 10 MHz ripple-based on-time controlled buck converter is presented.A novel low-cost dual ripple compensation,which consists of coupling capacitor compensation and passive equivalent series resistance compensation, is proposed to achieve a fast load transient response and robust stability simultaneously.Implemented in a 2P4M 0.35μm CMOS process,the converter achieves fix-frequency output with a ripple of below 10 mV and an overshoot of 10 mV at 400 mA step load transient response.With width optimization of the power transistors in an ultra-heavy load and PFM control in a light load,the efficiency stays at over 83%for a load range from 20 mA to 1.5 A and the peak efficiency reaches 90.16%.     

一种平均电流模式控制的单电感双输出型开关电源转换器

An integrated single-inductor dual-output （SIDO） switching DC-DC converter is presented. The outputs are specified with 1.2 V/400 mA and 1.8 V/200 mA. A decoupling small signal model is proposed to analyze the multi-loop system and to design the on-chip compensators. An average current control mode is introduced with lossless, continuous current detection. The converter has been fabricated in a 0.25μm 2P4M CMOS process. The power efficiency is 86% at a total output power of 840 mW while the output ripples are about 40 mV at an oscillator frequency of 600 kHz.     

A fixed frequency fast transient response DC-DC controller for VRM application Chen Mingyang(陈明阳), Zhao Menglian*(赵梦恋), Wu Xiaobo(吴晓波)

A 2V-10A fast transient response DC-DC buck controller based on fixed frequency hysteresis control is presented. A carefully designed output voltage filter detects the output capacitor current change which helps the controller to respond immediately after load changes. Adaptive hysteresis control guarantees the switching frequency to be the same as the reference frequency by using a CCII-composed circuit and current mirrors. The controller is designed and fabricated in a TSMC 0.35 μm process. Simulation and test results show that this con- troller achieves a 20 μs settling time in one single switching cycle when load current changes from 1 A to the full load condition at 10 A.     

A Dual-Mode Step-up DC/DC Converter IC with Current-Limiting and EMI Reduction Techniques

This paper presents a novel dual-mode step-up （boost） DC/DC converter. Pulse-frequency modulation （PFM） is used to improve the efficiency at light load. This converter can operate between pulse-width modulation （PWM） and pulse-frequency modulation. The converter will operate in PFM mode at light load and in PWM mode at heavy load. The maximum conversion efficiency of this converter is 96%. The conversion efficiency is greatly improved when load current is below 100 mA. Additionally, a soft-start circuit and a variable-sawtooth frequency circuit are proposed in this paper. The former is used to avoid the large switching current at the start up of the converter and the latter is utilized to reduce the EMI of the converter.     

一种具有动态零点补偿的电流模DC-DC降压型转换器

To achieve fast transient response for a DC-DC buck converter,an adaptive zero compensation circuit is presented.The compensation resistance is dynamically adjusted according to the different output load conditions, and achieves an adequate system phase margin under the different conditions.An improved capacitor multiplier circuit is adopted to realize the minimized compensation capacitance size.In addition,analysis of the small-signal model shows the correctness of the mechanism of the proposed adaptive zero compensation technique.A currentmode DC-DC buck converter with the proposed structure has been implemented in a 0.35μm CMOS process,and the die size is only 800×1040μm~2.The experimental results show that the transient undershoot/overshoot voltage and the recovery times do not exceed 40 mV and 30μs for a load current variation from 100 mA to 1 A.     

Load adaptive start-up scheme for synchronous boost DC-DC converter

This paper presents a load adaptive soft-start scheme through which the inductor current of the synchronous boost DC-DC converter can trace the load current at the start-up stage. This scheme effectively eliminates the inrush-current and over-shoot voltage and improves the load capability of the converter. According to the output voltage, the start-up process is divided into three phases and at each phase the inductor current is limited to match the load. In the pre-charge phase, a step-increasing constant current gives a smooth rise of the output voltage which avoids inrush current and ensures the converter successfully starts up at different load situations. An additional ring oscillator operation phase enables the converter to start up as low as 1.4 V. When the converter enters into the system loop soft-start phase, an output voltage and inductor current detection methods make the transition of the phases smooth and the inductor current and output voltage rise steadily. Effective protection circuits such as short-circuit protection, current limit circuit and over-temperature protection circuit are designed to guarantee the safety and reliability of the chip during the start-up process. The proposed start-up circuit is implemented in a synchronous boost DC-DC converter based on TSMC 0.35μm CMOS process with an input voltage range 1.4-4.2 V, and a steady output voltage 5 V, and the switching frequency is 1 MHz. Simulation results show that inrush current and overshoot voltage are suppressed with a load range from 0-2.1 A, and inductor current is as low as 259 mA when the output shorts to the ground.     

电流模降压变换器抗干扰电流采样电路设计

A novel anti-jamming integrated CMOS current-sensing circuit for current-mode buck regulators is presented. Based on the widely-used traditional current-sensing structure, anti-jamming performance is improved significantly by adding on-chip capacitors and one-shot circuit. Also the transient response is faster through the introduction of current offset. The circuit is concise, simple to implement and suits for SoC applications with single power supply. A dualoutput current-mode DC-DC buck converter with proposed structure has been fabricated with a 0.5 μm CMOS process for validation. In the 2.5–5.5 V input range, the two channels work steadily in the load current range of 0–600 mA. And the measured maximum efficiency is up to 96%.     

DCM,FSM,dead time and width controllers for a high frequency high efficiency buck DC-DC converter over a wide load range

This paper presents a width controller,a dead time controller,a discontinuous current mode(DCM) controller and a frequency skipping modulation(FSM) controller for a high frequency high efficiency buck DC-DC converter. To improve the efficiency over a wide load range,especially at high switching frequency,the dead time controller and width controller are applied to enhance the high load efficiency,while the DCM controller and FSM controller are proposed to increase the light load efficiency.The proposed D...     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks