Impact of cathode channel depth on performance of direct methanol fuel cells

The major functions of bipolar plates in fuel cell systems are to transport effectively the reactants and the products to and from the electrodes, and to collect efficiently the current that is generated in the cell. A suitable approach to enhance the performance of the bipolar plate with respect to mass transport is to optimize the channel dimension and shape. In this study, the impact of the cathode channel depth on the performance of direct methanol fuel cells is investigated. When the channel depth of the bipolar plate is decreased from 1.0 to 0.3 mm, the cell performance increases and also remains stable during continuous operation of the cell. The decreased channel depth leads to an increase in the linear velocity of the reactants and products at a given volumetric flow rate that, in turn, facilitates their mass transport. Furthermore, in smaller channels (shallower channels), the pressure drop is increased and this can lead to an increase in partial pressure of the oxygen, which has a positive impact on cell performance. The effect of cathode channel depth on the transport behaviour of reactants and products is studied by means of employing the transparent plates, which are designed to monitor visually the flow of reactants and products in the cathode channels. Additionally, the pressure drop and linear velocity in the cell is calculated by using a computational fluid dynamics (CFD) technique.     

Investigation of water droplet kinetics and optimization of channel geometry for PEM fuel cell cathodes

The kinetics and transport mechanisms of water droplets in model flow field channels of a low temperature polymer electrolyte fuel cell were investigated. The pressure drop at different air flows was measured for different channel geometries in a graphite plate as employed for fuel cell bipolar plates. The minimum air flow required for the movement of a water droplet in the flow channel was identified. From the experimental findings, recommendations for the development of flow fields with high condensate removal capabilities combined with low pressure differences were drawn to allow for an efficient operation of PEM fuel cells.     

Performance analysis of a proton exchange membrane fuel cell using tree-shaped designs for flow distribution

The performance of a proton exchange membrane (PEM) fuel cell is directly associated to the flow channels design embedded in the bipolar plates. The flow field within a fuel cell must provide efficient mass transport with a reduced pressure drop through the flow channels in order to obtain a uniform current distribution and a high power density. In this investigation, three-dimensional fuel cell models are analyzed using computational fluid dynamics (CFD). The proposed flow fields are radially designed tree-shaped geometries that connect the center flow inlet to the perimeter of the fuel cell plate. Three flow geometries having different levels of bifurcation were investigated as flow channels for PEM fuel cells. The performance of the fuel cells is reported in polarization and power curves, and compared with that of fuel cells using conventional flow patterns such as serpentine and parallel channels. Results from the flow analysis indicate that tree-shaped flow patterns can provide a relatively low pressure drop as well as a uniform flow distribution. It was found that as the number of bifurcation levels increases, a larger active area can be utilized in order to generate higher power and current densities from the fuel cell with a negligible increase in pumping power.     

Numerical simulation of laminar flow development with heat and mass transfer in PEM fuel cell flow channels having oxygen and hydrogen suction at one channel wall

Numerical simulation has been carried out of the fluid flow, heat and mass transfer for the developing laminar flow in polymer electrolyte membrane (PEM) fuel cell cathode and anode flow channels, respectively. Each flow channel is considered to be composed of two parallel walls, one porous (simulating electrode surface) and one non‐porous, or impermeable, wall (simulating bipolar plate surface). Various flow situations have been analyzed, and the local and the averaged friction coefficient, Nusselt number for heat transfer and Sherwood number for mass transfer are determined for various flow conditions corresponding to different stoichiometries, operating current densities and operating pressures of the cell. The effect of suction or injection (blowing) wall boundary condition has also been investigated, corresponding to the oxygen consumption in the cathode and hydrogen consumption in the anode. Correlations for the averaged friction coefficient, Nusselt and Sherwood numbers are developed, which can be useful for PEM fuel cell modeling and design calculations. Copyright © 2010 John Wiley & Sons, Ltd.     

Development of a novel radial cathode flow field for PEMFC

This paper presents an innovative radial flow field design for PEMFC cathode flow plates. This new design, which is in the form of a radial flow field, replaces the standard rectangular flow channels in exchange for a set of flow control rings. The control rings allow for better flow distribution and use of the active area. The radial field constructed of aluminum and plated with gold for superior surface and conductive properties. This material was selected based on the results obtained from the performance of the standard flow channels of serpentine and parallel designs constructed of hydrophilic gold and typical hydrophobic graphite materials. It is shown that the new flow field design performs significantly better compared to the current standard parallel channels in a dry-air-flow environment. The polarization curves for a dry flow, however, show excessive membrane drying with the radial design. Humidifying the air flow improves the membrane hydration, and in the meantime, the fuel cell with the innovative radial flow field produces higher current compared to other channel designs, even the serpentine flow field. The water removal and mass transport capacity of the radial flow field was proven to be better than parallel and serpentine designs. This performance increase was achieved while maintaining the pressure drop nearly half of the pressure drop measured in the serpentine flow field.     

A flow channel design procedure for PEM fuel cells with effective water removal

Proper water management in polymer electrolyte membrane (PEM) fuel cells is critical to achieve the potential of PEM fuel cells. Membrane electrolyte requires full hydration in order to function as proton conductor, often achieved by fully humidifying the anode and cathode reactant gas streams. On the other hand, water is also produced in the cell due to electrochemical reaction. The combined effect is that liquid water forms in the cell structure and water flooding deteriorates the cell performance significantly. In the present study, a design procedure has been developed for flow channels on bipolar plates that can effectively remove water from the PEM fuel cells. The main design philosophy is based on the determination of an appropriate pressure drop along the flow channel so that all the liquid water in the cell is evaporated and removed from, or carried out of, the cell by the gas stream in the flow channel. At the same time, the gas stream in the flow channel is maintained fully saturated in order to prevent membrane electrolyte dehydration. Sample flow channels have been designed, manufactured and tested for five different cell sizes of 50, 100, 200, 300 and 441 cm². Similar cell performance has been measured for these five significantly different cell sizes, indicating that scaling of the PEM fuel cells is possible if liquid water flooding or membrane dehydration can be avoided during the cell operation. It is observed that no liquid water flows out of the cell at the anode and cathode channel exits for the present designed cells during the performance tests, and virtually no liquid water content in the cell structure has been measured by the neutron imaging technique. These measurements indicate that the present design procedure can provide flow channels that can effectively remove water in the PEM fuel cell structure.     

Optimal design of cathode flow channel for air-cooled PEMFC with open cathode

Air-cooled open-cathode low temperature proton exchange membrane fuel cell (AO-LTPEMFC) with low weight, small volume and compact system has become the new potential power source in the unmanned aerial vehicle (UAV). However, the desirable parameters of the cathode channel are a very important factor to influence the cell performance and the compact of the stack, which have the higher requirements put forward to the structural designs of the cathode channel of AO-LTPEMFC. Thus, some single AO-LTPEMFC fabricated with different width:0.9–1.5 mm, depth:1.1–1.5 mm, ratio (width/landing):1:0.7–1:1.3 and bending:0–10° of the cathode channel was investigated to optimize the cell performance and temperature distribution in the 2 mm plate and determine desirable design parameters. The results show that the different design parameters of the cathode channel affect the contact resistance, oxygen mass transfer of cathode and pressure drop in air flow. For AO-LTPEMFC, to keep the best performance, the cathode channel design parameters should be operated at appropriate width, as deep as possible, small ratio and bending. Through the comparison of various designs, combined with practice process, the optimum design size with width (1.1 mm) × depth (1.3 mm) × width/landing (1:0.7) × bending angel (θ) (5°) was obtained based on the 2 mm thickness of the bipolar plate, which could get the maximum performance and improve the compactness of system. Moreover, analysis in this study will provide a new guideline for the development of cathode flow field plate design in application.     

NUMERICAL analysis of the effects of current collector plate geometry on performance in a cylindrical PEM fuel cell

In this study, a numerical analysis was conducted to investigate the effects of current collector plate geometry on performance in a cylindrical PEM (Proton Exchange Membrane) fuel cell. For this purpose, 2 anode and cathode current collector plate geometries for each helix channel and straight channel were designed. Current collector plates with different geometries were combined with different sequences, and four different main model fuel cell geometries were created. Accordingly, anode and cathode current collector plates for Model-1, Model-2, Model-3, and Model-4 geometries were determined as straight-straight, helix-helix, straight-helix, and helix-straight, respectively. Using these model geometries, simulations were conducted for three different operating pressures, four different operating flow rates, and ten different operating voltages. It was observed that when helix flow channels were used instead of straight flow channels in current collection plate geometries, the flow density increased by approximately 63.18%. The results also revealed that the current density increased by approximately 206.9% when the fuel cell operating pressure increased. In addition, the power density increased as the operating pressure increased. As the gas flow to anode and cathode increased, a 19.05% increase in the current increase in the pressure difference was observed. As a result, the helix flow channel usage performed better than the straight flow channel for the parameters adopted in this study.     

Design and simulation of a novel bipolar plate based on lung‐shaped bio‐inspired flow pattern for PEM fuel cell

Finding the optimal flow pattern in bipolar plates of a proton exchange membrane is a crucial step for enhancing the performance of the device. This design plays a critical role in fluid mass transport through microporous layers, charge transfer through conductive media, management of the liquid water produced in microchannels, and microporous layers and heat management in fuel cells. This article investigates different types of common flow patterns in bipolar plates while considering a uniform pressure and velocity distribution as well as a uniform distribution of reactants through all the surfaces of the catalyst layer as the design criteria so that there would be a consistent electron production by the catalyst layer. Then, by identifying the important parameters in achieving the best performance of a fuel cell, a microfluidic flow pattern is inspired from the lungs in the human body, and an innovative bipolar plate is suggested, which was not proposed before. Afterwards, numerical simulations were carried out using computational fluid dynamics methods, and the mentioned bipolar plate called lung‐shaped bipolar plate was modeled. Simulations in this research showed that the lung‐shaped microfluidic flow pattern is an appropriate flow pattern to gain maximum power and energy density. In other words, the best polarization curve and power density curve are obtained by using the lung‐shaped bipolar plate in a proton exchange membrane fuel cell compared with previously suggested patterns. Copyright © 2017 John Wiley & Sons, Ltd.     

Three-dimensional computational fluid dynamics modeling of anode-supported planar SOFC

Modeling plays a very important role in the development of fuel cells and fuel cell systems. The aim of this work is to investigate the electrochemical processes of a Solid Oxide Fuel Cell (SOFC) and to evaluate the performance of the proposed SOFC design. For this aim a three-dimensional Computational Fluid Dynamics (CFD) model has been developed for an anode-supported planar SOFC with corrugated bipolar plates serving as gas channels and current collector. The conservation of mass, momentum, energy and species is solved by using the commercial CFD code FLUENT in the developed model. The add-on FLUENT SOFC module is implemented for modeling the electrochemical reactions, loss mechanisms and related electric parameters throughout the cell. The distributions of temperature, flow velocity, pressure and gaseous (fuel and air) concentrations through the cell structure and gas channels is investigated. The relevant fuel cell variables such as the potential and current distribution over the cell and fuel utilization are calculated and studied. The modeling results indicate that, for the proposed SOFC design, reasonably uniform distributions of current density over the active cell area can be achieved. The geometry of the cathode gas channel has a substantial effect on the oxygen distribution and thus the overall cell performance. Methods for arriving at improved cell designs are discussed.     

Influence of geometric parameters of the flow fields on the performance of a PEM fuel cell. A review

The proton Exchange membrane fuel cell (PEMFC) performance depends not only on many factors including the operation conditions, transport phenomena inside the cell and kinetics of the electrochemical reactions, but also in its physical components; membrane electrode assembling (MEA) and bipolar plates (BPs). Among the PEM stack components, bipolar plates are considered one of the crucial ones, as they provide one of the most important issues regarding the performance of a stack, the homogeneous distribution of the reactive gases all over the catalyst surface and bipolar plate areas through, the so call, flow channels; physical flow patterns or paths fabricated on the BPs surfaces to guide the gases all along the BPs for its correct distribution. The failure in flow distribution among different unit cells may severely influence the fuel cell stack performance. Thus, to overcome such possible failures, the design of more efficient flow channels has received considerable attention in the research community for the last decade.     

质子交换膜燃料电池双极板的设计与模拟分析

质子交换膜燃料电池是直接将化学能转换为电能的装置,双极板上的流道结构对燃料电池的工作性能具有较大的影响。根据应用要求设计了具有平行流道、蛇形流道及希尔伯特分形流道的双极板结构,模拟计算了氢气在不同类型的流道和气体扩散层中的分布状态,分析了燃料电池的输出电流密度和功率密度随电极间电压的变化特点,比较了不同的流道结构对燃料电池输出电流密度的影响,以及不同的工作温度及气体压强的情况下,燃料电池输出电流密度随温度及压强的变化规律。     

Numerical simulation of two-phase flow in a multi-gas channel of a proton exchange membrane fuel cell

Understanding the two-phase distribution characteristics within the multi-gas channel of a fuel cell is important for improving fuel cell performance. In the paper, the volume of fluid model is used to predict the dynamic behaviour of water in the multi-gas channel, analyze the pressure drop, velocity distribution, and flow resistance coefficient between different channels, and investigate the influence of operating conditions, surface wettability and channel structure on the two-phase distribution characteristics in the channel. The results show that water undergoes the processes of growth, separation, single droplet transport, wall impact, droplet collision, liquid film formation, and liquid film transport in the multi-gas channel. Inlet velocity and surface wettability significantly affect the pressure drop, water saturation, and surface water coverage. As the inlet velocity and gas diffusion layer surface wettability increase, the flow resistance coefficient and unevenness of the distribution decrease, indicating that the in-channel flow distribution homogeneity is enhanced. The rectangular channel has better water removal and flow distribution uniformity than the tapered channel, and the unevenness of distribution decreases significantly with decreasing rectangular width, from 0.15715 to 0.00315. The research work is a guide to understanding water transport in multi-gas channels, accelerating water removal, and improving inter-channel flow distribution uniformity.     

Investigation of bio-inspired flow channel designs for bipolar plates in proton exchange membrane fuel cells

Proton exchange membrane (PEM) fuel cell performance is directly related to the flow channel design on bipolar plates. Power gains can be found by varying the type, size, or arrangement of channels. The objective of this paper is to present two new flow channel patterns: a leaf design and a lung design. These bio-inspired designs combine the advantages of the existing serpentine and interdigitated patterns with inspiration from patterns found in nature. Both numerical simulation and experimental testing have been conducted to investigate the effects of two new flow channel patterns on fuel cell performance. From the numerical simulation, it was found that there is a lower pressure drop from the inlet to outlet in the leaf or lung design than the existing serpentine or interdigitated flow patterns. The flow diffusion to the gas diffusion layer was found be to more uniform for the new flow channel patterns. A 25 cm² fuel cell was assembled and tested for four different flow channels: leaf, lung, serpentine and interdigitated. The polarization curve has been obtained under different operating conditions. It was found that the fuel cell with either leaf or lung design performs better than the convectional flow channel design under the same operating conditions. Both the leaf and lung design show improvements over previous designs by up to 30% in peak power density.     

Development of cylindrical PEM fuel cells with semi-cylindrical cathode current collectors

Proton exchange membrane (PEM) fuel cells are attractive because of advantages such as low-temperature operation, no emission of harmful gases and high efficiency. However, the bipolar plates used in the state-of-the-art planar architecture are costly and increase the dead weight of the cell. In addition, the flow channels in the planar fuel cell increase the difficulty in removing the water produced in the cathode during cell operation. Cylindrical PEM fuel cells, on the other hand, do not require bipolar plates and there is no need for precisely machined flow channels. Thus, cylindrical PEM fuel cells are cheap, efficient in water management, and possess higher volumetric and gravimetric power density compared to planar PEM fuel cells. The design of a cylindrical fuel cell is very simple, but the fabrication of the same is fairly complex. In this work, a novel cathode current collector design for cylindrical PEM fuel cell has been developed. The cell performance was limited by low open circuit voltage and high ohmic resistance. The open circuit voltage of the cell is increased from 0.85 V to 0.95 V using an acrylic based adhesive to seal the membrane edges. The contact resistance of the cell is reduced from 75 mOhm to 50 mOhm by increasing the contact pressure on the membrane electrode assembly and it is further reduced to 30 mOhm by gold coating the current collectors. Furthermore, a cumulative 40% increase in peak power has been achieved from the optimization of cathode rib width and hydrogen flow rate. The optimized cell delivered a current density of 400 mA/cm² at 0.6 V and peak power of 2 W, which is appreciable considering the fact that the cell is air-breathing and operated with very minimal subsystems.     

Numerical evaluation of a PEM fuel cell with conventional flow fields adapted to tubular plates

In this research a 3D numerical study on a PEM fuel cell model with tubular plates is presented. The study is focused on the performance evaluation of three flow fields with cylindrical geometry (serpentine, interdigitated and straight channels) in a fuel cell. These designs are proposed not only with the aim to reduce the pressure losses that conventional designs exhibit with rectangular flow fields but also to improve the mass transport processes that take place in the fuel cell cathode. A commercial computational fluid dynamics (CFD) code was used to solve the numerical model. From the numerical solution of the fluid mechanics equations and the electrochemical model of Butler-Volmer different analysis of pressure losses, species concentration, current density, temperature and ionic conductivity were carried out. The results were obtained at the flow channels and the catalyst layers as well as in the gas diffusion layers and the membrane interfaces. Numerical results showed that cylindrical channel configurations reduced the pressure losses in the cell due to the gradual reduction of the angle at the flow path and the twist of the channel, thus facilitating the expulsion of liquid water from the gas diffusion layers and in turn promoting a high oxygen concentration at the triple phase boundary of the catalyst layers. Moreover, numerical results were compared to polarization curves and the literature data reported for similar designs. These results demonstrated that conventional flow field designs applied to conventional tubular plates have some advantages over the rectangular designs, such as uniform pressure and current density distributions among others, therefore they could be considered for fuel cell designs in portable applications.     

Numerical study of water management in the air flow channel of a PEM fuel cell cathode

The water management in the air flow channel of a proton exchange membrane (PEM) fuel cell cathode is numerically investigated using the FLUENT software package. By enabling the volume of fraction (VOF) model, the air–water two-phase flow can be simulated under different operating conditions. The effects of channel surface hydrophilicity, channel geometry, and air inlet velocity on water behavior, water content inside the channel, and two-phase pressure drop are discussed in detail. The results of the quasi-steady-state simulations show that: (1) the hydrophilicity of reactant flow channel surface is critical for water management in order to facilitate water transport along channel surfaces or edges; (2) hydrophilic surfaces also increase pressure drop due to liquid water spreading; (3) a sharp corner channel design could benefit water management because it facilitates water accumulation and provides paths for water transport along channel surface opposite to gas diffusion layer; (4) the two-phase pressure drop inside the air flow channel increases almost linearly with increasing air inlet velocity.     

Flow channel shape optimum design for hydroformed metal bipolar plate in PEM fuel cell

Bipolar plate is one of the most important and costliest components of polymer electrolyte membrane (PEM) fuel cells. Micro-hydroforming is a promising process to reduce the manufacturing cost of PEM fuel cell bipolar plates made of metal sheets. As for hydroformed bipolar plates, the main defect is the rupture because of the thinning of metal sheet during the forming process. The flow channel section decides whether high quality hydroformed bipolar plates can be successively achieved or not. Meanwhile, it is also the key factor that is related with the reaction efficiency of the fuel cell stacks. In order to obtain the optimum flow channel section design prior the experimental campaign, some key geometric dimensions (channel depth, channel width, rib width and transition radius) of flow channel section, which are related with both reaction efficiency and formability, are extracted and parameterized as the design variables. By design of experiments (DOE) methods and an adoptive simulated annealing (ASA) optimization method, an optimization model of flow channel section design for hydroformed metal bipolar plate is proposed. Optimization results show that the optimum dimension values for channel depth, channel width, rib width and transition radius are 0.5, 1.0, 1. 6 and 0.5 mm, respectively with the highest reaction efficiency (79%) and the acceptable formability (1.0). Consequently, their use would lead to improved fuel cell efficiency for low cost hydroformed metal bipolar plates.     

Numerical investigation of transport phenomena in high temperature proton exchange membrane fuel cells with different flow field designs

In this work, a three-dimensional, non-isothermal, steady-state model for high temperature proton exchange membrane fuel cells with phosphoric acid polybenzimidazole membrane has been developed using computational fluid dynamics. The importance of the gas flow field design on the transport characteristics and cell performance is revealed by solving the mass, momentum, species, energy, and charge conservation equations. The numerical results show that the best cell performance is provided by the fuel cell with serpentine flow channel flow field. However, the pressure drop is also very high due to the large length of the serpentine channel. In addition, the velocity, oxygen mass fraction, and temperature distributions are unevenly distributed over the entire active area of the fuel cell having straight channels with small manifolds, especially at low cell voltages when a large amount of oxygen is required. The cell performance and durability can be significantly affected by the uniformity of the reactants within the fuel cell. It is suggested that the flow field configurations must be optimized to obtain uniform distributions of the reactants, maximize the cell performance, and minimize the pressure drop penalty. The present results provide detailed information about transport characteristics within fuel cells and give guidelines for design and manufacturing of current collectors.     

Materials and design development for bipolar/end plates in fuel cells

Bipolar/end plate is one of the most important and costliest components of the fuel cell stack and accounts to more than 80% of the total weight of the stack. In the present work, we focus on the development of alternative materials and design concepts for these plates. A prototype one-cell polymer electrolyte membrane (PEM) fuel cell stack made out of SS-316 bipolar/end plate was fabricated and assembled. The use of porous material in the gas flow-field of bipolar/end plates was proposed, and the performance of these was compared to the conventional channel type of design. Three different porous materials were investigated, viz. Ni–Cr metal foam (50 PPI), SS-316 metal foam (20 PPI), and the carbon cloth. It was seen that the performance of fuel cell with Ni–Cr metal foam was highest, and decreased in the order SS-316 metal foam, conventional multi-parallel flow-field channel design and carbon cloth. This trend was explained based on the effective permeability of the gas flow-field in the bipolar/end plates. The use of metal foams with low permeability values resulted in an increased pressure drop across the flow-field which enhanced the cell performance.