Impact of synthesis conditions on the structure and performance of Li2FeSiO4

Three different synthesis techniques (hydrothermal synthesis, modified Pechini synthesis and Pechini synthesis) were successfully used for preparation of Li₂FeSiO₄ samples. The obtained samples possess some differences in the morphology and in the particle size, as well as in the presence of in situ formed carbon. The best electrochemical performance has been obtained with the smallest particles embedded into carbon matrix. Such a Li₂FeSiO₄/C composite contains the highest amounts of impurities (Fe₂O₃, SiO₂ and Li₂SiO₃) and only 68.8 at.% of iron is in the form of Fe^II as detected by Mössbauer spectroscopy, respectively. Despite the highest amount of impurities, the sample shows the highest reversible capacity (approximately 100 mAh g⁻¹ based on whole silicate-derived material). With the proper structuring of Li₂FeSiO₄/C composites, utilisation of large part of capacity is also possible at current densities corresponding to C/5 and C/2 cycling rate. A lower amount of impurities was found in the samples that do not contain any in situ carbon after synthesis. Among them, the highest purity is possessed by the sample prepared at 900 °C, as determined using Mössbauer spectroscopy. The results obtained by Mössbauer spectroscopy and XRD analysis indicate on the differences in the crystal structure between the thermally treated samples and the sample prepared by hydrothermal synthesis.     

Electrochemical properties of Li2ZrO3-coated silicon/graphite/carbon composite as anode material for lithium ion batteries

Silicon/graphite/disordered carbon (Si/G/DC) is coated by Li₂ZrO₃ using Zr(NO₃)₄·5H₂O and CH₃COOLi·2H₂O as coating reagents. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) are used to characterize Li₂ZrO₃-coated Si/G/DC composite. The Li₂ZrO₃-coated Si/G/DC composite exhibits a high reversible capacity with no capacity fading from 2nd to 70th cycle, indicating its excellent cycleability when used as anode materials for lithium ion batteries. A compact and stable solid-electrolyte interphase (SEI) layer is formed on the surface of Li₂ZrO₃-coated Si/G/DC electrode. Analysis of electrochemical impedance spectra (EIS) shows that the resistance of the coated material exhibits less variation during cycling, which indicates the integrity of electrode structure is kept during cycling. XPS shows that F and P elements do not appear in the SEI layers of Li₂ZrO₃-coated Si/G/DC electrode, while they have a relatively high content in SEI layers of Si/G/DC electrode. The improvement of Li₂ZrO₃-coated Si/G/DC is attributed to the decrease of lithium insertion depth and the formation of stable SEI film.     

Li2MSiO4 (M = Fe and/or Mn) cathode materials

Two iso-structural end members of the family of orthosilicates, i.e. Li₂MSiO₄ (M = Mn and Fe) and their solid solutions, were prepared and electrochemically characterized for potential use in Li-ion batteries. Due to the low specific conductivity (∼5 × 10⁻¹⁶ S cm⁻¹ for Li₂MnSiO₄ and ∼6 × 10⁻¹⁴ S cm⁻¹ for Li₂FeSiO₄ at room temperature), small particles in an intimate contact with a conducting phase (i.e. carbon) are needed. Li₂MSiO₄/C composites (M = Mn and/or Fe) prepared by the Pechini synthesis generally leads to 30–50 nm large particles embedded in a carbon matrix. The amount of carbon in the composite is close to 10 wt.% for the Li₂FeSiO₄/C composite and slightly more than 5 wt.% for the Li₂MnSiO₄/C composite. In situ XRD experiment confirms a structural collapse of Li₂MnSiO₄ and the observed structural stability is completely different for Li₂FeSiO₄, which undergoes a fully reversible two-phase transition. Solid solutions between Li₂MnSiO₄ and Li₂FeSiO₄ in principle lead to higher capacities (>1e⁻ per transition metal is feasible). For a long-term operation the cut-off voltage should be properly chosen. Electrochemical characterisation and in situ XRD experiments suggest the use of cut-off voltage close to 4.2 V.     

Nano Li4Ti5O12–LiMn2O4 batteries with high power capability and improved cycle-life

We report the effects of electrode thickness, cathode particle size and morphology, cathode carbon coating matching ratio and laminate structure on the electrochemical characteristics of nanosized Li₄Ti₅O₁₂–LiMn₂O₄ batteries. We show that a correct adjustment of these parameters resulted in significant improvements in power capability and cycle-life of such devices, making them competitive, low-cost and safe battery chemistry for next generation Li-ion batteries. In addition, Li₄Ti₅O₁₂ reversible specific capacity beyond three Li-ions intercalation is reported.     

Effects of roasting temperature and modification on properties of Li2FeSiO4/C cathode

Li₂FeSiO₄/C cathodes were synthesized by combination of wet-process method and solid-state reaction at high temperature, and effects of roasting temperature and modification on properties of the Li₂FeSiO₄/C cathode were investigated. The XRD patterns of the Li₂FeSiO₄/C samples indicate that all the samples are of good crystallinity, and a little Fe₃O₄ impurity was observed in them. The primary particle size rises as the roasting temperature increases from 600 to 750 °C. The Li₂FeSiO₄/C sample synthesized at 650 °C has good electrochemical performances with an initial discharge capacity of 144.9 mAh g⁻¹ and the discharge capacity remains 136.5 mAh g⁻¹ after 10 cycles. The performance of Li₂FeSiO₄/C cathode is further improved by modification of Ni substitution. The Li₂Fe_0.9Ni_0.1SiO₄/C composite cathode has an initial discharge capacity of 160.1 mAh g⁻¹, and the discharge capacity remains 153.9 mAh g⁻¹ after 10 cycles. The diffusion coefficient of lithium in Li₂FeSiO₄/C is 1.38 × 10⁻¹² cm² s⁻¹ while that in Li₂Fe_0.9Ni_0.1SiO₄/C reaches 3.34 × 10⁻¹² cm² s⁻¹.     

Li4Ti5O12/CNTs composite anode material for large capacity and high-rate lithium ion batteries

Li₄Ti₅O₁₂ sub-micro crystallites are synthesized by ball-milling and one-step sintering under different heat treatment temperature from 700 °C to 900 °C. The composite electrode of Li₄Ti₅O₁₂/carbon nanotubes (CNTs) is prepared by mixing powders of Li₄Ti₅O₁₂ and CNTs in different weight ratios. Before mixing, in order to disperse CNTs in Li₄Ti₅O₁₂ particles preferably, the CNTs are cut and dispersed by hyperacoustic shear method and the composite electrodes of low resistance of about 20–30 Ω are obtained. The composite electrodes have steady discharge platform of 1.54 V and large specific capacity, initial discharge capacities are 168, 200, 196, 176 mAh g⁻¹ in different Li₄Ti₅O₁₂:CNTs weight ratios of 94:1, 92:3, 90:5, 88:7 respectively at 0.1 C discharge rate for the Li₄Ti₅O₁₂ synthesized in an optimized heat treatment temperature of 800 °C. In our experimental range, the composite electrode in a CNTs weight ratio of 3:92 shows the best performance under different discharge rate such as the initial capacity is 200 mAh g⁻¹ with discharge capacities retention rate of nearly 100%. Its capacity is about 151 mAh g⁻¹ under 20 C rate discharge condition with excellent high-rate performance. There is almost no decline after 20th cycles under 10 C rate discharging condition.     

Synthesis of single crystalline Li0.44MnO2 nanowires with large specific capacity and good high current density property for a positive electrode of Li ion battery

The fabrication of single crystalline Li_0.44MnO₂ nanowires for the positive electrode of lithium ion battery is reported. The single crystalline Li_0.44MnO₂ nanowires are obtained by lithium exchange reaction of Na_0.44MnO₂ nanowires with high aspect ratio. The Li_0.44MnO₂ nanowires indicate both the large specific capacity of around 250 mAh g⁻¹ (1.5-4.5 V vs. Li/Li⁺) and the good high current density property for the positive electrode of lithium ion battery.     

High-density spherical Li4Ti5O12/C anode material with good rate capability for lithium ion batteries

Li₄Ti₅O₁₂ is a very promising anode material for lithium secondary batteries. To improve the material's rate capability and pile density is considered as the important researching direction. One effective way is to prepare powders composed of spherical particles containing carbon black. A novel technique has been developed to prepare spherical Li₄Ti₅O₁₂/C composite. The spherical precursor containing carbon black is prepared via an “outer gel” method, using TiOCl₂, C and NH₃ as the raw material. Spherical Li₄Ti₅O₁₂/C powders are synthesized by sintering the mixture of spherical precursor and Li₂CO₃ in N₂. The investigation of TG/DSC, SEM, XRD, Brunauer–Emmett–Teller (BET) testing, laser particle size analysis, tap-density testing and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂/C composite prepared by this method are spherical, has high tap-density and excellent rate capability. It is observed that the tap-density of spherical Li₄Ti₅O₁₂/C powders (the mass content of C is 4.8%) is as high as 1.71 g cm⁻³, which is remarkably higher than the non-spherical Li₄Ti₅O₁₂. Between 1.0 and 3.0 V versus Li, the initial discharge specific capacity of the sample is as high as 144.2 mAh g⁻¹, which is still 128.8 mAh g⁻¹ after 50 cycles at a current density of 1.6 mA cm⁻².     

Electrochemical characteristics of Li2−xVTiO4 rock salt phase in Li-ion batteries

Li_2−xVTiO₄/C sample with a disordered rock salt structure was successfully prepared by annealing at a temperature of 850 °C. The electrochemical oxidation in the first cycle occurs at voltages above 4 V vs. metallic lithium, while the shapes of the electrochemical curves in consequent reduction-oxidation processes show a monotonous change of the potential between the selected cut-off voltages. A linear combination fit of individual XANES spectra was used for the determination of the oxidation states of as prepared sample and intermediate states during oxidation and reduction. In the as-prepared sample, vanadium was found to be in the average oxidation state of V^3.5+ and was additionally oxidized to V^3.8+ by the electrochemical charging. During the discharge process, the vanadium oxidation state was reduced to V^3.0+. In situ X-ray diffraction patterns and EXAFS analysis suggest good structural stability during oxidation and reduction, which is also reflected in the cycling stability if batteries were cycled in the voltage window between 2.0 V and 4.4 V. Extension of the lower cut-off voltage to 1.0 V doubles the capacity retention with the improved capacity stability if compared with several high capacity vanadium based materials.     

Electrochemical performance of spinel LiMn2O4 cathode materials made by flame-assisted spray technology

Spinel lithium manganese oxide LiMn₂O₄ powders were synthesized by a flame-assisted spray technology (FAST) with a precursor solution consisting of stoichiometric amounts of LiNO₃ and Mn(NO₃)₂·4H₂O dissolved in methanol. The as-synthesized LiMn₂O₄ particles were non-agglomerated, and nanocrystalline. A small amount of Mn₃O₄was detected in the as-synthesized powder due to the decomposition of spinel LiMn₂O₄ at the high flame temperature. The impurity phase was removed with a post-annealing heat-treatment wherein the grain size of the annealed powder was 33 nm. The charge/discharge curves of both powders matched the characteristic plateaus of spinel LiMn₂O₄ at 3 V and 4 V vs. Li. However, the annealed powder showed a higher initial discharge capacity of 115 mAh g⁻¹ at 4 V. The test cell with annealed powder showed good rate capability between a voltage of 3.0 and 4.3 V and a first cycle coulombic efficiency of 96%. The low coulombic efficiency from capacity fading may be due to oxygen defects in the annealed powder. The results suggest that FAST holds potential for rapid production of uniform cathode materials with low-cost nitrate precursors and minimal energy input.     

Development of high power lithium-ion batteries: Layer Li[Ni0.4Co0.2Mn0.4]O2 and spinel Li[Li0.1Al0.05Mn1.85]O4

Layer Li[Ni_0.4Co_0.2Mn_0.4]O₂ and lithium excess spinel Li[Li_0.1Al_0.05Mn_1.85]O₄ were compared as positive electrode materials for high power lithium-ion batteries. Physical properties were examined by Rietveld refinement of X-ray diffraction pattern and scanning electron microscopic studies. From continuous charge and discharge tests at higher currents and different temperature environments using 3Ah class lithium-ion batteries, it was found that both materials presented plausible battery performances such as rate capability, cyclability at 60 °C at elevated temperature, and low temperature properties as well.     

Effects of supersonic treatment on the electrochemical properties and crystal structure of LiMn1.5Ni0.5O4 as a cathode material for Li ion batteries

The electrochemical properties and crystal structure of LiMn_1.5Ni_0.5O₄ treated with supersonic waves in an aqueous Ni-containing solution were investigated by performing charge-discharge tests, inductively coupled plasma (ICP) analysis, scanning electron microscopy (SEM), iodometry, X-ray diffraction (XRD), powder neutron diffraction and synchrotron powder XRD. The charge-discharge curve of LiMn_1.5Ni_0.5O₄ versus Li/Li⁺ has plateaus at 4.1 and 4.7 V. The 4.1 V versus Li/Li⁺ plateau due to the oxidation of Mn^3+/4+ was reduced by the supersonic treatment. During the charge-discharge cycling test at 25 °C, the supersonic treatment increased the discharge capacity of the 50th cycle. Rietveld analysis of the neutron diffraction patterns revealed that the Ni occupancy of the 4b site in LiMn_1.5Mn_0.5O₄, which is mainly occupied by Ni, was increased by the supersonic treatment. This result suggests that Ni²⁺ is partially substituted for Mn^3+/4+ during the supersonic treatment.     

Hydrothermal synthesis of Co2SnO4 nanocrystals as anode materials for Li-ion batteries

Cubic spinel Co₂SnO₄ nanocrystals are successfully synthesized via a simple hydrothermal reaction in alkaline solution. The effect of alkaline concentration, hydrothermal temperature, and hydrothermal time on the structure and morphology of the resultant products were investigated based on X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It is demonstrated that pure Co₂SnO₄ nanocrystals with good crystallinity can be obtained in NaOH solution (2.0 M) at 240 °C for 48 h. The galvanostatic charge/discharge and cyclic voltammetry were conducted to measure the electrochemical performance of the Co₂SnO₄ nanocrystals. It is shown that Co₂SnO₄ nanocrystals exhibit good electrochemical activity with high reversible capacity (charge capacity) of 1088.8 mAh g⁻¹ and good capacity retention as anode materials for Li-ion batteries, much better than that of bulk Co₂SnO₄ prepared by high temperature solid-state reaction.     

Effect of FePO4 coating on electrochemical and safety performance of LiCoO2 as cathode material for Li-ion batteries

LiCoO₂ was surface modified by a coprecipitation method followed by a high-temperature treatment in air. FePO₄-coated LiCoO₂ was characterized with various techniques such as X-ray diffraction (XRD), auger electron spectroscopy (AES), field emission scanning electron microscope (FE-SEM), energy dispersive spectroscopy (EDS), transmission electron microscope (TEM), electrochemical impedance spectroscopy (EIS), 3 C overcharge and hot-box safety experiments. For the 14500R-type cell, under a high charge cutoff voltage of 4.3 and 4.4 V, 3 wt.% FePO₄-coated LiCoO₂ exhibits good electrochemical properties with initial discharge specific capacities of 146 and 155 mAh g⁻¹ and capacity retention ratios of 88.7 and 82.5% after 400 cycles, respectively. Moreover, the anti-overcharge and thermal safety performance of LiCoO₂ is greatly enhanced. These improvements are attributed to the FePO₄ coating layer that hinders interaction between LiCoO₂ and electrolyte and stabilizes the structure of LiCoO₂. The FePO₄-coated LiCoO₂ could be a high performance cathode material for lithium-ion battery.     

Preparation and electrochemical investigation of Li2CoPO4F cathode material for lithium-ion batteries

In this paper, we report the electrochemical characteristics of a novel cathode material, Li₂CoPO₄F, prepared by solid-state reactions. The solid-state reaction mechanism involved in synthesizing the Li₂CoPO₄F also is analyzed in this paper. When cycled between 2.0 V and 5.0 V during cyclic voltammetry measurements, the Li₂CoPO₄F samples present one, fully reversible anodic reaction at 4.81 V. When cycled between 2.0 V and 5.5 V, peaks occurring at 4.81 V and 5.12 V in the first anodic scan evolved to one broad oxidative, mound-like pattern in subsequent cycles. Correspondingly, the X-ray diffraction (XRD) pattern of the Li₂CoPO₄F electrode discharged from 5.5 V to 2.0 V is slightly different from the patterns exhibited by a fresh sample and the sample discharged from 5.0 V to 2.0 V. This difference may correspond to a structural relaxation that appears above 5 V. In the constant current cycling measurements, the Li₂CoPO₄F samples exhibited a capacity as high as 109 mAh g⁻¹ and maintained a good cyclability between 2.0 V and 5.5 V vs. Li/Li⁺. XRD measurements confirmed that the discharged state is Li₂CoPO₄F. Combining these XRD results and electrochemical data proved that up to 1 mol Li⁺ is extractable when charged to 5.5 V.     

Effects of dopant on the electrochemical performance of Li4Ti5O12 as electrode material for lithium ion batteries

The effects of dopant on the electrochemical properties of spinel-type Li_3.95M_0.15Ti_4.9O₁₂ (M = Al, Ga, Co) and Li_3.9Mg_0.1Al_0.15Ti_4.85O₁₂ were systematically investigated. Charge–discharge cycling were performed at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.3 and 0.5 V, the experimental results showed that Al³⁺ dopant greatly improved the reversible capacity and cycling stability over the pristine Li₄Ti₅O₁₂. The substitution of the Ga³⁺ slightly increased the capacity of the Li₄Ti₅O₁₂, but did not essentially alleviate the degradation of cycling stability. Dopants such as Co³⁺ and Mg²⁺ to some extent worsened the electrochemical performance of the Li₄Ti₅O₁₂.     

The study of Mg2Si/carbon composites as anode materials for lithium ion batteries

The study of Mg₂Si/C composites as anode materials for lithium ion batteries is reported in this paper. Firstly, Mg₂Si was synthesized by mechanically activated annealing (MAA) technique and the preparing conditions for pure Mg₂Si alloy were investigated and optimized. Then the composite materials of Mg₂Si and carbon materials such as CNTs and CMS with different ratios were prepared by the followed ball-milling techniques. Their electrochemical performances were compared by the galvanostatically charge/discharge and EIS experiments. The pure Mg₂Si alloy delivers a large initial capacity, but the capacity decreases rapidly with cycling. In contrast, the composites show good cyclic stability and deliver a reversible capacity of about 400 mAh g⁻¹ with 40% carbon in the composite. The results of EIS indicate that the composite of Mg₂Si/CMS has better interface stability than that of pure Mg₂Si materials.     

Effect of Co3(PO4)2 coating on Li[Co0.1Ni0.15Li0.2Mn0.55]O2 cathode material for lithium rechargeable batteries

To prepare a high-capacity cathode material with improved electrochemical performance for lithium rechargeable batteries, Co₃(PO₄)₂ nanoparticles are coated on the surface of powdered Li[Co_0.1Ni_0.15Li_0.2Mn_0.55]O₂, which is synthesized by a simple combustion method. The coated powder prepared under proper conditions for Co₃(PO₄)₂ content and annealing temperature shows an optimum coating layer that consists of a Li_xCoPO₄ phase formed by reaction with lithium impurities during heat treatment. A sample coated with 3 wt.% Co₃(PO₄)₂ and annealed at 800 °C proves to be the best in terms of specific capacity, cycle performance and rate capability. Thermal stability is also enhanced by the coating, as demonstrated a decrease in the onset temperature and/or the heat generated during thermal runaway.     

Fabrication and electrochemical properties of three-dimensional net architectures of anatase TiO2 and spinel Li4Ti5O12 nanofibers

As a new type of electrodes engineering method with three-dimensional (3D) architecture for 3D rechargeable lithium ion batteries, an electrospinning has been successfully employed to prepare 3D net architectures of anatase TiO₂ and spinel Li₄Ti₅O₁₂ nanofibers. Scanning electron microscopy, X-ray diffraction, cyclic voltammetry and the discharge/charge measurements were used to characterize their structures and electrochemical properties. Our results demonstrated that 3D architectures stacked from a cross-bar array of electrospun anatase TiO₂ nanofibers could be accomplished but were destroyed after the insertion of Li ion. Significantly, spinel Li₄Ti₅O₁₂ could be selected as one of promise candidates for the realization of 3D batteries considering its structure stability of 3D spinel Li₄Ti₅O₁₂ nanofibers associated with well cyclability.