Optimized solid-state synthesis of LiFePO4 cathode materials using ball-milling

Olivine-type LiFePO₄ cathode materials were synthesized by a solid-state reaction method and ball-milling. The ball-milling time, heating time and heating temperature are optimized. A heating temperature higher than 700 °C resulted in the appearance of impurity phase Fe₂P and growth of large particle, which was shown by high resolution X-ray diffraction and field emission scanning electron microscopy. The impurity phase Fe₂P exhibited a considerable capacity loss at the 1st cycle and a gradual increase in discharge capacity upon cycling. Moreover, it exhibited an excellent high-rate capacity of 104 mAh g⁻¹ at 3 C in spite of the large particle size. The optimum synthesis conditions for LiFePO₄ were ball-milling for 24 h and heat-treatment at 600 °C for 3 h. LiFePO₄/Li cells showed an enhanced cycling performance and a high discharge capacity of 160 mAh g⁻¹ at 0.1 C.     

Effect of mechanical activation process parameters on the properties of LiFePO4 cathode material

Pure, nano-sized LiFePO₄ and carbon-coated LiFePO₄ (LiFePO₄/C) positive electrode (cathode) materials are synthesized by a mechanical activation process that consists of high-energy ball milling and firing steps. The influence of the processing parameters such as firing temperature, firing time and ball-milling time on the structure, particle size, morphology and electrochemical performance of the active material is investigated. An increase in firing temperature causes a pronounced growth in particle size, especially above 600 °C. A firing time longer than 10 h at 600 °C results in particle agglomeration; whereas, a ball milling time longer than 15 h does not further reduce the particle size. The electrochemical properties also vary considerably depending on these parameters and the highest initial discharge capacity is obtained with a LiFePO₄/C sample prepared by ball milling for 15 h and firing for 10 h at 600 °C. Comparison of the cyclic voltammograms of LiFePO₄ and LiFePO₄/C shows enhanced reaction kinetics and reversibility for the carbon-coated sample. Good cycle performance is exhibited by LiFePO₄/C in lithium batteries cycled at room temperature. At the high current density of 2C, an initial discharge capacity of 125 mAh g⁻¹ (73.5% of theoretical capacity) is obtained with a low capacity fading of 0.18% per cycle over 55 cycles.     

Simple and fast synthesis of LiFePO4-C composite for lithium rechargeable batteries by ball-milling and microwave heating

A very simple and rapid method for synthesizing LiFePO₄-C composite has been developed by vibrant type ball-milling for 30 min and microwave heating for 2–4 min. X-ray diffraction and Mössbauer spectroscopy verify that well-crystallized LiFePO₄ without Fe³⁺ impurities is obtained. From laser particle size analysis and transmission electron microscopy, it is confirmed that a LiFePO₄-C composite with fine and uniform particle size (mean particle size ≤0.640 μm, D75 in volume distribution ≤0.592 μm) and with extremely uniform carbon distribution is prepared by vibrant type ball-milling and microwave heating. The LiFePO₄-C delivers a high initial discharge capacity of 161 mAh g⁻¹ at C/10 and shows very stable cycling behaviour.     

Effect of synthesis temperature on the properties of LiFePO4/C composites prepared by carbothermal reduction

LiFePO₄/C composite cathode materials were synthesized by carbothermal reduction method using inexpensive FePO₄ as raw materials and glucose as conductive additive and reducing agent. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and particle size analysis. Cyclic voltammetry (CV) and charge/discharge cycling performance were used to characterize their electrochemical properties. The results showed that the LiFePO₄/C composite synthesized at 650 °C for 9 h exhibited the most homogeneous particle size distribution. Residual carbon during processing was coated on LiFePO₄, resulting in the enhancement of the material's electronic properties. Electrochemical measurements showed that the discharge capacity first increased and then decreased with the increase of synthesis temperature. The optimal sample synthesized at 650 °C for 9 h exhibited a highest initial discharge capacity of 151.2 mA h g⁻¹ at 0.2 C rate and 144.1 mA h g⁻¹ at 1 C rate with satisfactory capacity retention rate.     

A simple,cheap soft synthesis routine for LiFePO4 using iron(III) raw material

An order olivine structure LiFePO₄ was synthesized with a simple rheological phase reaction (RPR) of LiOH·H₂O and FePO₄·4H₂O in the presence of PEG as a reductive agent and carbon source. A required amount of water was added to the starting materials to form the rheological precursor and decomposed at 700 °C to form the crystalline phase LiFePO₄ directly, without ball-milling, preparation of intermediates, pre-sintering and post-deposition treatment. Fine particles with an average particle size about 216 nm are examined by scanning electron microscopy (SEM) and optical particle size analyzer. An initial discharge capacity of 157 mAh g⁻¹ was achieved for the as-prepared LiFePO₄ material with a rate of 0.1C (17 mA g⁻¹), what's more, this material shows excellent specific capacity, charge–discharge efficiency and cycle efficiency at high current rates, almost no capacity loss can be observed up to 40 cycles with the rate of 1, 2 and 3C at room temperature. The simple, cheap process as well as the excellent high-rate performance makes this RPR method feasible commercially.     

Synthesis of carbon-coated LiFePO4 nanoparticles with high rate performance in lithium secondary batteries

A novel preparation technique was developed for synthesizing carbon-coated LiFePO₄ nanoparticles through a combination of spray pyrolysis (SP) with wet ball milling (WBM) followed by heat treatment. Using this technique, the preparation of carbon-coated LiFePO₄ nanoparticles was investigated for a wide range of process parameters such as ball-milling time and ball-to-powder ratio. The effect of process parameters on the physical and electrochemical properties of the LiFePO₄/C composite was then discussed through the results of X-ray diffraction (XRD) analysis, field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the Brunauer-Emmet-Teller (BET) method and the use of an electrochemical cell of Li|1 M LiClO₄ in EC:DEC = 1:1|LiFePO₄. The carbon-coated LiFePO₄ nanoparticles were prepared at 500 °C by SP and then milled at a rotating speed of 800 rpm, a ball-to-powder ratio of 40/0.5 and a ball-milling time of 3 h in an Ar atmosphere followed by heat treatment at 600 °C for 4 h in a N₂ + 3% H₂ atmosphere. SEM observation revealed that the particle size of LiFePO₄ was significantly affected by the process parameters. Furthermore, TEM observation revealed that the LiFePO₄ nanoparticles with a geometric mean diameter of 146 nm were coated with a thin carbon layer of several nanometers by the present method. Electrochemical measurement demonstrated that cells containing carbon-coated LiFePO₄ nanoparticles could deliver markedly improved battery performance in terms of discharge capacity, cycling stability and rate capability. The cells exhibited first discharge capacities of 165 mAh g⁻¹ at 0.1 C, 130 mAh g⁻¹ at 5 C, 105 mAh g⁻¹ at 20 C and 75 mAh g⁻¹ at 60 C with no capacity fading after 100 cycles.     

Study of LiFePO4 cathode materials coated with high surface area carbon

LiFePO₄ is a potential cathode material for 4 V lithium-ion batteries. Carbon-coated lithium iron phosphates were prepared using a high surface area carbon to react precursors through a solid-state process, during which LiFePO₄ particles were embedded in amorphous carbon. The carbonaceous materials were synthesized by the pyrolysis of peanut shells under argon, where they were carbonized in a two-step process that occurred between 573 and 873 K. The shells were also treated with a proprietary porogenic agent with the goal of altering the pore structure and surface area of the pyrolysis products. The electrochemical properties of the as-prepared LiFePO₄/C composite cathode materials were systematically characterized by X-ray diffraction, scanning electron microscope, element mapping, energy dispersive spectroscopy, Raman spectroscopy, and total organic carbon (TOC) analysis. In LiFePO₄/C composites, the carbon not only increases rate capability, but also stabilizes capacity. In fact, the capacity of the composites increased with the specific surface area of carbon. The best result was observed with a composite made of 8.0 wt.% with a specific surface area of 2099 m² g⁻¹. When high surface area carbon was used as a carbon source to produce LiFePO₄, overall conductivity increased from 10⁻⁸ to 10⁻⁴ S cm⁻¹, because the inhibition of particle growth during the final sintering process led to greater specific capacity, improved cycling properties and better rate capability compared to a pure olivine LiFePO₄ material.     

Cathode performance of olivine-type LiFePO4 synthesized by chemical lithiation

Chemical lithiation with LiI in acetonitrile was performed for amorphous FePO₄ synthesized from an equimolar aqueous suspension of iron powder and an aqueous solution of P₂O₅. An orthorhombic LiFePO₄ olivine structure was obtained by annealing a chemically lithiated sample at 550 °C for 5 h in Ar atmosphere. The average particle size remained at approximately 250 nm even after annealing. The lithium content in the sample was quantitatively confirmed by Li atomic absorption analysis and ⁵⁷Fe Mössbauer spectroscopy. While an amorphous FePO₄/carbon composite cathode has a monotonously decreasing charge–discharge profile with a reversible capacity of more than 140 mAh g⁻¹, the crystallized LiFePO₄/carbon composite shows a 3.4 V plateau corresponding to a two-phase reaction. This means that the lithium in the chemically lithiated sample is electrochemically active. Both amorphous FePO₄ and the chemically lithiated and annealed crystalline LiFePO₄ cathode materials showed good cyclability (more than 140 mAh g⁻¹ at the 40th cycle) and good discharge rate capability (more than 100 mAh g⁻¹ at 5.0 mA cm⁻²). In addition, the fast-charge performance was found to be comparable to that with LiCoO₂.     

Synthesis of LiFePO4/C composite with high-rate performance by starch sol assisted rheological phase method

LiFePO₄/C composite was synthesized at 600 °C in an Ar atmosphere by a soluble starch sol assisted rheological phase method using home-made amorphous nano-FePO₄ as the iron source. XRD, SEM and TEM observations show that the LiFePO₄/C composite has good crystallinity, ultrafine sphere-like particles of 100-200 nm size and in situ carbon. The synthesized LiFePO₄ could inherit the morphology of FePO₄ precursor. The electrochemical performance of the LiFePO₄ by galvanostatic cycling studies demonstrates excellent high-rate cycle stability. The Li/LiFePO₄ cell displays a high initial discharge capacity of more than 157 mAh g⁻¹ at 0.2C and a little discharge capacity decreases from the first to the 80th cycle (>98.3%). Remarkably, even at a high current density of 30C, the cell still presents good cycle retention.     

Electrochemical properties of LiFePO4 prepared via hydrothermal route

LiFePO₄ as a cathode material for rechargeable lithium batteries was prepared by hydrothermal process at 170 °C under inert atmosphere. The starting materials were LiOH, FeSO₄, and (NH₄)₂HPO₄. The particle size of the obtained LiFePO₄ was 0.5 μm. The electrochemical properties of LiFePO₄ were characterized in a mixed solvent of ethylene carbonate and diethyl carbonate (1:1 in volume) containing 1.0 mol dm⁻³ LiClO₄. The hydrothermally synthesized LiFePO₄ exhibited a discharge capacity of 130 mA h g⁻¹, which was smaller than theoretical capacity (170 mA h g⁻¹). The annealing of LiFePO₄ at 400 °C in argon atmosphere was effective in increasing the discharge capacity. The discharge capacity of the annealed LiFePO₄ was 150 mA h g⁻¹.     

Synthesis and characterization of Carbon Nano Fiber/LiFePO4 composites for Li-ion batteries

Carbon Nano Fibers (CNFs) coated with LiFePO₄ particles have been prepared by a non-aqueous sol–gel technique. The functionalization of the CNFs by HNO₃ acid treatment has been confirmed by Raman and XPS analyses. The samples pure LiFePO₄ and LiFePO₄–CNF have been characterized by XRD, SEM, RAMAN, XPS and electrochemical analysis. The LiFePO₄–CNF sample shows better electrochemical performance compared to as-prepared LiFePO₄. LiFePO₄–CNF (10 wt.%) delivers a higher specific capacity (∼140 mAh g⁻¹) than LiFePO₄ with carbon black (25 wt.%) added after synthesis (∼120 mAh g⁻¹) at 0.1C.     

Effects of carbon coating and iron phosphides on the electrochemical properties of LiFePO4/C

Carbon coated LiFePO₄ (LiFePO₄/C) with different contents of high electron conductive iron phosphide phase was synthesized by an aqueous sol–gel method in a reductive sintering atmosphere. Different synthesis parameters were used for adjusting the microstructure and phase compositions of the products. The effects of the carbon coating and iron phosphides on the electrochemical properties of the LiFePO₄/C electrodes were studied by means of testing the discharge capacities at rates of 0.1–5C (1C = 170 mAh g⁻¹) and analyzing the CV curves. The results show that carbon coating in a content of 1.5 wt.% derived from the carbon source of ethylene glycol greatly decreases the particle size of LiFePO₄ in one order in the specific surface area, and significantly improves the rate capability of LiFePO₄. The effect of the content of FeP on the capacity of the carbon coated LiFePO₄ was different at different discharge rates. Increasing the content of FeP from 1.2 to 3.7 wt.% slightly decreases the capacity of LiFePO₄/C at low discharge rate (0.1C and 1C), but obviously increases the capacity of LiFePO₄/C when the discharge rate is increased to 5C. For the carbon free sample, even it also has 1.8 wt.% FeP, it still possesses poor capacity due to the large particle size of LiFePO₄ and the lack of conductivity. And too much iron phosphides lowers the discharge capacity of the electrode since they are inert for the deinsertion/insertion of lithium ion.     

Synthesis and electrochemical properties of olivine LiFePO4 prepared by a carbothermal reduction method

LiFePO₄/C composite cathode material was prepared by carbothermal reduction method, which uses NH₄H₂PO₄, Li₂CO₃ and cheap Fe₂O₃ as starting materials, acetylene black and glucose as carbon sources. The precursor of LiFePO₄/C was characterized by differential thermal analysis and thermogravimetry. X-ray diffraction (XRD), scanning electron microscopy (SEM) micrographs showed that the LiFePO₄/C is olivine-type phase, and the addition of the carbon reduced the LiFePO₄ grain size. The carbon is dispersed between the grains, ensuring a good electronic contact. The products sintered at 700 °C for 8 h with glucose as carbon source possessed excellent electrochemical performance. The synthesized LiFePO₄ composites showed a high electrochemical capacity of 159.3 mAh g⁻¹ at 0.1 C rate, and the capacity fading is only 2.2% after 30 cycles.     

Structural and electrochemical properties of Cl-doped LiFePO4/C

Cl-doped LiFePO₄/C cathode materials were synthesized through a carbothermal reduction route, and the microstructure and electrochemical performances were systematically studied. Cl-doped LiFePO₄/C cathode materials presented a high discharge capacity of ∼90 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. Electrochemical impedance spectroscopy and cyclic voltamperometry indicated the optimized electrochemical reaction and Li⁺ diffusion in the bulk of LiFePO₄ due to Cl-doping. The improved Li⁺ diffusion capability is attributed to the microstructure modification of LiFePO₄ via Cl-doping.     

PPy doped PEG conducting polymer films synthesized on LiFePO4 particles

In this work, polyethyleneglycole (PEG) is introduced into polypyrrole (PPy) film coated on LiFePO₄ powder particles to promote the properties of cathode material for lithium-ion batteries. The enhancement of the electrochemical activity by the substitution of a carbon with electrochemically active polymer is investigated. Films of the PPy doped with the PEG were prepared by the chemical oxidative polymerization of pyrrole (Py) monomer. PEG has been added as an additive during polymerization process to improve mechanical and structural properties of the PPy in final PPy/PEG-LiFePO₄ cathode material. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge/discharge measurements were employed to characterize the electrochemical properties of PPy/PEG-LiFePO₄ material. The electrochemical performance of PPy-LiFePO₄ electrodes was greatly improved by introduction of PEG into the PPy films. Charge/discharge measurements confirmed the increase in capacity when applying PEG in PPy. The morphology and particle sizes of the prepared cathode powder material were investigated by scanning electron microscopy (SEM) and particle size analysis (PSA). Distribution of PPy and PPy/PEG films onto the LiFePO₄ particles surface was studied by time of flight secondary ion mass spectrometry (TOF-SIMS). In addition to polymeric coating layer on the surface of PPy-LiFePO₄ composite particles, some PPy unequally distributed between the particles was found. The median diameter value is 4.92 μm for PPy-LiFePO₄ sample. TOF-SIMS measurements and SEM images confirmed that thickness of polypyrrole coating on LiFePO₄ particles is about 100 nm.     

LiCr0.2Ni0.4Mn1.4O4 spinels exhibiting huge rate capability at 25 and 55 °C: Analysis of the effect of the particle size

The comparison of the rate capability of LiCr_0.2Ni_0.4Mn_1.4O₄ spinels synthesized by the sucrose aided combustion method at 900, 950 and 1000 °C is presented. XRD and TEM studies show that the spinel cubic structure remains unchanged on heating but the particle size is notably modified. Indeed, it increases from 695 nm at 900 °C to 1465 nm at 1000 °C. The electrochemical properties have been evaluated by galvanostatic cycling at 25 and 55 °C between 1 C and 60 C discharge rates. At both temperatures, all samples exhibit high working voltage (∼4.7 V), elevated capacity (∼140 mAh g⁻¹) and high cyclability (capacity retention ∼99% after 50 cycles even at 55 °C). The samples also have huge rate capability. They retain more than 70% of their maximum capacity at the very fast rate of 60 C. The effect of the particle size on the rate capability at 25 and at 55 °C has been investigated. It was demonstrated that LiCr_0.2Ni_0.4Mn_1.4O₄ annealed at 900 °C, with the lowest particle size, has the best electrochemical performances. In fact, among the LiNi_0.5Mn_1.5O₄-based cathodes, SAC900 exhibits the highest rate capability ever published. This spinel, able to deliver 31,000 W kg⁻¹ at 25 °C and 27,500 W kg⁻¹ at 55 °C is a really promising cathode for high-power Li-ion battery.     

Morphology and electrical properties of carbon coated LiFePO4 cathode materials

Core-shell LiFePO₄@C composites were synthesized successfully from FePO₄/C precursor using the polyvinyl alcohol (PVA) as the reducing agent, followed by a chemical vapor deposition (CVD) assisted solid-state reaction in the presence of Li₂CO₃. Some physical and chemical properties of the products were characterized by X-ray powder diffraction (XRD), Raman, SEM, TEM techniques. The effect of morphology and electrochemical properties of the composites were thoroughly investigated. XRD patterns showed that LiFePO₄ has an order olivine structure with space group of Pnma. TEM micrographs exhibited that the LiFePO₄ particles encapsulated with 3-nm thick carbon shells. The powders were homogeneous with grain size of about 0.8 μm. Compared with those synthesized by traditional organic carbon source mixed method, LiFePO₄@C composite synthesized by CVD method exhibited better discharge capacity at initial 155.4 and 135.8 mAh g⁻¹ at 0.1C and 1C rate, respectively. It is revealed that the carbon layer coated on the surface of LiFePO₄ and the amorphous carbon wrapping and connecting the particles enhanced the electronic conductivity and rate performances of the cathode materials.     

Effects of TiO2 coating on high-temperature cycle performance of LiFePO4-based lithium-ion batteries

LiFePO₄ particles were coated with TiO₂ (molar ratio = 3%) via a sol–gel process, and the effects of the coating on cycle performance of LiFePO₄ cathode at 55 °C against either a Li or a C (mesocarbon microbead) anode were investigated. It was found that, while the coating reduces capacity fading of the LiFePO₄/Li cell, it imposes a deteriorating effect on the LiFePO₄/C cell. Analyses on cell impedance and electrode surface morphology and composition showed that the oxide coating reduced Fe dissolution from the LiFePO₄ cathode and hence alleviated the impedance increase associated with the erosion process. This leads to reduced capacity fading as observed for the LiFePO₄/Li cell. However, the oxide coating itself was eroded upon cycling, and the dissolved Ti ions were subsequently reduced at the anode surface. Ti deposit on the C anode was found to be more active than Fe in catalyzing the formation of the solid-electrolyte interphase (SEI) layer, causing accelerated capacity decay for the LiFePO₄/C cell. The results point out the importance of evaluating the effect of cathode coating material on the anode side, which has generally been overlooked in the past studies.     

A novel sol-gel method based on FePO4·2H2O to synthesize submicrometer structured LiFePO4/C cathode material

Carbon coated LiFePO₄/C cathode material is synthesized with a novel sol-gel method, using cheap FePO₄·2H₂O as both iron and phosphorus sources and oxalic acid (H₂C₂O₄·2H₂O) as both complexant and reductant. In H₂C₂O₄ solution, FePO₄·2H₂O is very simple to form transparent sols without controlling the pH value. Pure submicrometer structured LiFePO₄ crystal is obtained with a particle size ranging from 100 to 500 nm, which is also uniformly coated with a carbon layer, about 2.6 nm in thickness. The as-synthesized LiFePO₄/C sample exhibits high initial discharge capacity 160.5 mAh g⁻¹ at 0.1 C rate, with a capacity retention of 98.7% after 50th cycle. The material also shows good high-rate discharge performances, about 106 mAh g⁻¹ at 10 C rate. The improved electrochemical properties of as-synthesized LiFePO₄/C are ascribed to its submicrometer scale particles and low electrochemical impedance. The sol-gel method may be of great interest in the practical application of LiFePO₄/C cathode material.     

Improved high-rate charge/discharge performances of LiFePO4/C via V-doping

V-doped LiFePO₄/C cathode materials were prepared through a carbothermal reduction route. The microstructure was characterized by X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy. The electrochemical Li⁺ intercalation performances of V-doped LiFePO₄/C were compared with those of undoped one through galvanostatic intermittent titration technique, cyclic voltamperometry, and electrochemical impedance spectrum. V-doped LiFePO₄/C showed a high discharge capacity of ∼70 mAh g⁻¹ at the rate of 20 C (3400 mA g⁻¹) at room temperature. The significantly improved high-rate charge/discharge capacity is attributed to the increase of Li⁺ ion “effective” diffusion capability.