Novel branched sulfonated poly(ether ether ketone)s membranes for direct methanol fuel cells

In this article, novel branched sulfonated poly(ether ether ketone)s (Br-SPEEK) containing various amounts of 1,3,5-tris(4-fluorobenzoyl)benzene as the branching agent have been successfully prepared. Compared with the traditional linear polymer membranes, the membranes prepared by Br-SPEEK showed improved mechanical strength, excellent dimensional stability and superior oxidative stability with similar proton conductivity. Notably, the Br-SPEEK-10 membrane began to break after 267 min in Fenton's reagent at 80 °C, which was 4 times longer than that of the L-SPEEK. Although the proton conductivity decreased with the addition of the branching agent, satisfying methanol permeability value was observed (down to 6.3 × 10⁻⁷ cm² s⁻¹), which was much lower than Nafion 117 (15.5 × 10⁻⁷ cm² s⁻¹). All the results indicated that the novel branched sulfonated poly(ether ether ketone)s membrane was potential candidate as proton conductive membranes for application in fuel cells.     

Sulfonated poly(ether ether ketone)/polybenzimidazole oligomer/epoxy resin composite membranes in situ polymerization for direct methanol fuel cell usages

A diamine-terminated polybenzimidazole oligomer (o-PBI) has been synthesized for introducing the benzimidazole groups (BI) into sulfonated poly(ether ether ketone) (SPEEK) membranes. SPEEK/o-PBI/4,4′-diglycidyl(3,3′,5,5′-tetramethylbiphenyl) epoxy resin (TMBP) composite membranes in situ polymerization has been prepared for the purpose of improving the performance of SPEEK with high ion-exchange capacities (IEC) for the usage in the direct methanol fuel cells (DMFCs). The composite membranes with three-dimensional network structure are obtained through a cross-linking reaction between PBI oligomer and TMBP and the acid-base interaction between sulfonic acid groups and benzimidazole groups. Resulting membranes show a significantly increasing of all of the properties, such as high proton conductivity (0.14 S cm⁻¹ at 80 °C), low methanol permeability (2.38 × 10⁻⁸ cm² s⁻¹), low water uptake (25.66% at 80 °C) and swelling ratio (4.11% at 80 °C), strong thermal and oxidative stability, and mechanical properties. Higher selectivity has been found for the composite membranes in comparison with SPEEK. Therefore, the SPEEK/o-PBI/TMBP composite membranes show a good potential in DMFCs usages.     

Novel sulfonated poly(ether ether ketone)s containing nitrile groups and their composite membranes for fuel cells

A series of novel sulfonated poly(ether ether ketone)s containing a cyanophenyl group (SPEEKCNxx) are prepared based on (4-cyano)phenylhydroquinone via nucleophilic substitution polycondensation reactions. To further improve their properties, novel composite membranes composed of sulfonated poly(ether ether ketone)s containing cyanophenyl group as an acidic component and aminated poly(aryl ether ketone) as a basic component are successfully prepared. Most of the membranes exhibit excellent thermal, oxidative and dimensional stability, low-swelling ratio, high proton conductivity, low methanol permeability and high selectivity. The proton conductivities of the membranes are close to Nafion 117 at room temperature. And especially, the values of SPEEKCN40 and its composite membranes are higher than Nafion 117 at 80 °C (0.17 S cm⁻¹ of Nafion, 0.26 S cm⁻¹ of SPEEKCN40, 0.20 S cm⁻¹ of SPEEKCN40-1, and 0.18 S cm⁻¹ of SPEEKCN40-2). Moreover, the methanol permeability is one order magnitude lower than that of Nafion 117. All the data prove that both copolymers and their composite membranes may be potential proton exchange membrane for fuel cells applications.     

Sulfonated titania submicrospheres-doped sulfonated poly(ether ether ketone) hybrid membranes with enhanced proton conductivity and reduced methanol permeability

Sulfonated titania submicrospheres (TiO₂-SO₃H) prepared through a facile chelation method are incorporated into sulfonated poly(ether ether ketone) (SPEEK) to fabricate organic-inorganic hybrid membranes with enhanced proton conductivity and reduced methanol permeability for potential use in direct methanol fuel cells (DMFCs). The pristine titania submicrospheres (TiO₂) with a uniform particle size are synthesized through a modified sol-gel method and sulfonated using 4,5-dihydroxy-1,3-benzenedisulfonic acid disodium salt as the sulfonation reagent. The sulfonation process is confirmed by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectra (XPS). The hybrid membranes are systematically characterized in terms of thermal property, mechanical property, ionic exchange capacity (IEC), swelling behavior, and microstructural features. The methanol barrier property and the proton conductivity of the SPEEK/TiO₂-SO₃H hybrid membranes are evaluated. The presence of the fillers reduces methanol crossover through the membrane. Compared with the unsulfonated TiO₂-doped membranes, the TiO₂-SO₃H-doped ones exhibit higher proton conductivity due to the additional sulfonic acid groups on the surface of TiO₂. The hybrid membrane doped with 15 wt.% TiO₂-SO₃H submicrospheres exhibits an acceptable proton conductivity of 0.053 S cm⁻¹ and a reduced methanol permeability of 4.19 × 10⁻⁷ cm² s⁻¹.     

Preparation and characterization of sulfonated poly(tetra phenyl ether ketone sulfone)s for proton exchange membrane fuel cell

Sulfonated poly(tetra phenyl ether ketone sulfone)s SPTPEKS were successfully synthesized for proton exchange membrane. Poly(tetra phenyl ether ketone sulfone)s PTPEKS were prepared by the 4,4′-dihydroxydiphenylsulfone with 1,2-bis(4-fluorobenzoyl)-3,4,5,6-tetraphenylbenzene (BFBTPB) and 4,4′-difluorodiphenylsulfone, respectively, at 210 °C using potassium carbonate in sulfolane. PTPEKS were followed by sulfonation using chlorosulfonic acid and concentrated sulfuric acid at two stage reactions. Different contents of sulfonated unit of SPTPEKS (17, 20, 23 mol% of BFBTPB) were studied by FT-IR, ¹H NMR spectroscopy, and thermo gravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water. The ion exchange capacity (IEC) and proton conductivity of SPTPEKS were evaluated with increase of degree of sulfonation. The water uptake of synthesized SPTPEKS membranes exhibit 25–61% compared with 28% of Nafion 211^®. The SPTPEKS membranes exhibit proton conductivities (25 °C) of 11.7–25.3 × 10⁻³ S/cm compared with 33.7 × 10⁻³ S/cm of Nafion 211^®.     

A facile approach to prepare self-cross-linkable sulfonated poly(ether ether ketone) membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone) containing hydroxyl groups (SPEEK-OH) has been prepared for use as a proton exchange membrane (PEM) by reducing the carbonyl groups on the main chain of the polymers. With the goal of reducing water uptake and methanol permeability, a facile thermal-cross-linking process is used to obtain the cross-linked membranes. The properties of the cross-linked membranes with different cross-linked density are measured and compared with the pristine membrane. Notably, SPEEK-4 with the highest cross-linked density shows a water uptake of 39% and a methanol permeability of 2.52 × 10⁻⁷ cm² s⁻¹, which are much lower than those of the pristine membrane (63.2% and 5.37 × 10⁻⁷ cm² s⁻¹, respectively). These results indicate that this simple approach is very effective to prepare cross-linked proton exchange membranes for reducing water uptake and methanol permeability.     

Crosslinked sulfonated poly(arylene ether ketone) membranes bearing quinoxaline and acid-base complex cross-linkages for fuel cell applications

A series of crosslinkable sulfonated poly(arylene ether ketone)s (SPAEKs) were synthesized by copolymerization of 4,4′-biphenol with 2,6-difluorobenzil and 5,5′-carbonyl-bis(2-fluorobenzene-sulfonate). A facile crosslinking method was successfully developed, based on the cyclocondensation reaction of benzil moieties in polymer chain with 3,3′-diaminobenzidine to form quinoxaline groups acting as covalent and acid-base ionic crosslinking. The uncrosslinked and crosslinked SPAEK membranes showed high mechanical properties and the isotropic membrane swelling, while the later became insoluble in tested polar aprotic solvents. The crosslinking significantly improved the membrane performance, i.e., the crosslinked membranes had the lower membrane dimensional change, lower methanol permeability and higher oxidative stability than the corresponding precursor membranes, with keeping the reasonably high proton conductivity. The crosslinked membrane (C-B4) with an ion exchange capacity of 2.02 mequiv. g⁻¹ showed a reasonably high proton conductivity of 111 mS cm⁻¹ with a low water uptake of 42 wt% at 80 °C. C-B4 exhibited a low methanol permeability of 0.55 × 10⁻⁶ cm² s⁻¹ for 32 wt% methanol solution at 25 °C. The crosslinked SPAEK membranes have potential for PEFC and DMFC applications.     

Cross-linked membranes based on sulfonated poly (ether ether ketone) (SPEEK)/Nafion for direct methanol fuel cells (DMFCs)

A series of cross-linked membranes based on SPEEK/Nafion have been prepared to improve methanol resistance and dimension stability of SPEEK membrane for the usage in the direct methanol fuel cells (DMFCs). Sulfonated diamine monomer is synthesized and used as cross-linker to improve the dispersion of Nafion in the composite membranes and decrease the negative effect of cross-linking on proton conductivity of membranes. FT-IR analysis shows that the cross-linking reaction is performed successfully. The effects of different contents of Nafion on the properties of cross-linked membranes are investigated in detail. All the cross-linked membranes show lower methanol permeability and better dimensional stability compared with the pristine SPEEK membrane. SPEEK-N30 with the 30 wt % Nafion shows a methanol permeability of 0.73 × 10⁻⁶ cm² s⁻¹ and a water uptake of 24.4% at 25 °C, which are lower than those of the pristine membrane. Meanwhile, the proton conductivity of SPEEK-N30 still remains at 0.041 S cm⁻¹ at 25 °C, which is comparable to that of the pristine SPEEK membrane. All the results indicate that these cross-linked membranes based on SPEEK/Nafion show good prospect for the use as proton exchange membranes.     

Preparation of main-chain-type and side-chain-type sulfonated poly(ether ether ketone) membranes for direct methanol fuel cell applications

Novel main-chain-type and side-chain-type sulphonated poly(ether ether ketone)s (MS-SPEEKs) are synthesised by reacting the sulphonic acid groups of pristine SPEEKs with 2-aminoethanesulphonic acid to improve the nano-phase separated morphology of the material. ¹H NMR and FT-IR spectroscopy are employed to determine the structure and composition of main-chain-type and side-chain-type sulphonated polymers. Flexible and tough membranes with reasonable thermal properties are obtained. The MS-SPEEKs show good hydrolytic stability, and water uptake values ranging from 15% to 30% are observed. Compared to Nafion 117^®, the methanol permeability of the MS-SPEEKs is dramatically reduced to 8.83 × 10⁻⁸ cm² s⁻¹ to 3.31 × 10⁻⁷ cm² s⁻¹. The proton conductivity increases with increasing temperature, reaching 0.013-0.182 S cm⁻¹. A maximum power density and open circuit voltage of 115 mW cm⁻² and 0.830 V are obtained at 80 °C, respectively, which is significantly greater than the values generated with Nafion 117^®. The introduction of pendent side-chain-type sulphonic acid groups increases the single-cell performance by more than approximately 20%; thus, the lower water diffusivity, methanol permeability, electro-osmotic drag coefficient and high cell performance indicated that MS-SPEEK is a promising candidate for DMFC applications.     

Crosslinked sulfonated poly(ether ether ketone) proton exchange membranes for direct methanol fuel cell applications

In the present study, a series of the crosslinked sulfonated poly(ether ether ketone) (SPEEK) proton exchange membranes were prepared. The photochemical crosslinking of the SPEEK membranes was carried out by dissolving benzophenone and triethylamine photo-initiator system in the membrane casting solution and then exposing the resulting membranes after solvent evaporation to UV light. The physical and transport properties of crosslinked membranes were investigated. The membrane performance can be controlled by adjusting the photoirradiation time. The experimental results showed that the crosslinked SPEEK membranes with photoirradiation 10 min had the optimum performance for proton exchange membranes (PEMs). Compared with the non-crosslinked SPEEK membranes, the crosslinked SPEEK membranes with photoirradiation 10 min markedly improved thermal stabilities and mechanical properties as well as hydrolytic and oxidative stabilities, greatly reduced water uptake and methanol diffusion coefficients with only slight sacrifice in proton conductivities. Therefore, the crosslinked SPEEK membranes with photoirradiation 10 min were particularly promising as proton exchange membranes for direct methanol fuel cell (DMFC) applications.     

Molecular structure and transport dynamics in Nafion and sulfonated poly(ether ether ketone ketone) membranes

An atomistic simulation technique is performed to investigate the molecular structure and transport dynamics inside a hydrated Nafion membrane and a hydrated sulfonated poly(ether ether ketone ketone) (SPEEKK) membrane. The simulation system consists of the representative fragments of the polymer electrolytes, hydronium ions and solvent molecules, such as water plus methanol molecules. Simulation results show that the hydrated SPEEKK has less phase separation among hydrophobic and hydrophilic regions in comparison with the Nafion. Those water channels formed in the SPEEKK are much narrower compared to those in the Nafion. These characteristics lead to a lower mobility of hydronium ions and water molecules and hence relatively lower diffusion coefficient of methanol in the SPEEKK. It results in the reduction of the methanol permeation problem in direct methanol fuel cells.     

Nafion/nitrated sulfonated poly(ether ether ketone) membranes for direct methanol fuel cells

Sulfonated poly(ether ether ketone)s (SPEEKs) are substituted on the main chain of the polymer by nitro groups and blended with Nafion^® to attain composite membranes. The sulfonation, nitration and blending are achieved with a simple, inexpensive process, and the blended membranes containing the nitrated SPEEKs reveal a liquid-liquid phase separation. The blended membranes have a lower water uptake compared to recast Nafion^®, and the methanol permeability is reduced significantly to 4.29 × 10⁻⁷-5.34 × 10⁻⁷ cm² s⁻¹ for various contents of nitrated SPEEK for S63N17, and 4.72 × 10⁻⁷-7.11 × 10⁻⁷ cm² s⁻¹ for S63N38, with a maximum proton conductivity of ∼0.085 S cm⁻¹. This study examines the single-cell performance at 80 °C of Nafion^®/nitrated SPEEK membranes with various contents of nitrated SPEEK and a degree of nitration of 23-25 mW cm⁻² for S63N17 and 24-29 mW cm⁻² for S63N38. Both the power density and open circuit voltage are higher than those of Nafion^® 115 and recast Nafion^®.     

Preparation of nitrated sulfonated poly(ether ether ketone) membranes for reducing methanol permeability in direct methanol fuel cell applications

Sulfonated poly(ether ether ketone)s (SPEEKs) were further substituted on the polymer main chain by nitration. All sulfonation and nitration were achieved with an inexpensive and simple post substitute reaction. The nitrated SPEEKs have a high glass transition temperature and thermal decomposition temperature, and a lower water uptake than SPEEK, which provides sufficient mechanical strength without swelling in the direct methanol fuel cell (DMFC) application. The methanol permeability of nitrated SPEEKS is reduced to 1.76 × 10⁻⁷ cm² s⁻¹ for S53N22 and 1.86 × 10⁻⁷ cm² s⁻¹ for S63N17 with no loss of conductivity in the DMFC application, and a proton conductivity that reached 0.026 S cm⁻¹. The nitrated SPEEK membranes satisfy the requirements of proton-exchange membranes for the DMFC.     

Sulfonated poly(ether ether ketone) as an ionomer for direct methanol fuel cell electrodes

Sulfonated poly(ether ether ketone) has been investigated as an ionomer in the catalyst layer for direct methanol fuel cells (DMFC). The performance in DMFC, electrochemical active area (by cyclic voltammetry), and limiting capacitance (by impedance spectroscopy) have been evaluated as a function of the ion exchange capacity (IEC) and content (wt.%) of the SPEEK ionomer in the catalyst layer. The optimum IEC value and SPEEK ionomer content in the electrodes are found to be, respectively, 1.33 meq. g⁻¹ and 20 wt.%. The membrane-electrode assemblies (MEA) fabricated with SPEEK membrane and SPEEK ionomer in the electrodes are found to exhibit superior performance in DMFC compared to that fabricated with Nafion ionomer due to lower interfacial resistance in the MEA as well as larger electrochemical active area. The MEAs with SPEEK membrane and SPEEK ionomer also exhibit better performance than that with Nafion 115 membrane and Nafion ionomer due to lower methanol crossover and better electrode kinetics.     

Nafion-assisted cross-linking of sulfonated poly(arylene ether ketone) bearing carboxylic acid groups and their composite membranes for fuel cells

In this study, a new type of cross-linked composite membrane is prepared and considered for its potential applications in direct methanol fuel cell. Nafion and sulfonated poly(arylene ether ketone) bearing carboxylic acid groups (SPAEK-C) are blended and subsequently cross-linked by a Friedel-Craft reaction using the carboxylic acid groups in the SPAEK-C to achieve lower methanol permeability. The perfluoroalkyl sulfonic acid groups of Nafion act as a benign solid catalyst, which assist the cross-linking of SPAEK-C. The physical and chemical characterizations of the cross-linked composite membranes are performed by varying the contents of SPAEK-C. The c-Nafion-15% membrane exhibits appropriate water uptake (10.49-25.22%), low methanol permeability (2.57 × 10⁻⁷ cm² s⁻¹), and high proton conductivity (0.179 S cm⁻¹ at 80 °C). DSC and FTIR analyze suggest the cross-linking reaction. These results show that the self-cross-linking of SPAEK-C in the Nafion membrane can effectively reduce methanol permeability while maintaining high proton conductivity.     

Novel modification method to prepare crosslinked sulfonated poly(ether ether ketone)/silica hybrid membranes for fuel cells

Crosslinked organic-inorganic hybrid membranes are prepared from hydroxyl-functionalized sulfonated poly(ether ether ketone) (SPEEK) and various amounts of silica with the aims to improve dimensional stability and methanol resistance. The partially hydroxyl-functionalized SPEEK is prepared by the reduction of some benzophenone moieties of SPEEK into the corresponding benzhydrol moieties which is then reacted with (3-isocyanatopropyl)triethoxysilane (ICPTES) to get a side chained polymer bearing triethoxysilyl groups. These groups are subsequently co-hydrolyzed with tetraethoxysilane (TEOS) and allow the membrane to form a crosslinked network via a sol-gel process. The obtained hybrid membranes with covalent bonds between organic and inorganic phases exhibit much lower methanol swelling ratio and water uptake. With the increase of silica content, the methanol permeability coefficient of the hybrid membranes decreases at first and then increased. At silica content of about 6 wt.%, the methanol permeability coefficient reaches a minimum of 7.15 × 10⁻⁷ cm² s⁻¹, a 5-fold decrease compared with that of the pristine SPEEK. Despite the fact that the proton conductivity is decreased to some extent as a result of introduction of the silica, the hybrid membranes with silica content of 4-8 wt.% shows higher selectivity than Nafion117.     

Modification of sulfonated poly(ether ether ketone) proton exchange membrane for reducing methanol crossover

A drawback of sulfonated aromatic main-chain polymers such as sulfonated poly(ether ether ketone)s (SPEEKs) is their high methanol crossover when the proton conductivity is sufficient for direct methanol fuel cell (DMFC) applications. To overcome this disadvantage, in this paper, the SPEEK substrate was coated with the crosslinked chitosan (CS) barrier layer to form the two-layer composite membranes. Scanning electron microscope (SEM) micrographs showed that the CS layer was tightly adhered on the SPEEK substrate and the thickness of CS layer could be adjusted by varying the concentration of CS solution. It was noticed that with the increment of thickness of CS layer, the methanol diffusion coefficient of the composite membranes significantly dropped from 3.15 × 10⁻⁶ to 2.81 × 10⁻⁷ cm² s⁻¹ at 25 °C which was about one order of magnitude lower than those of the pure SPEEK and Nafion^® 117 membranes. In addition to the effective methanol barrier, the composite membranes possessed adequate thermal stability (the 5% weight lose temperature exceeded 240 °C) and good proton conductivity. The proton conductivity of all composite membranes was in the order of 10⁻² S cm⁻¹ and increased with the elevation of temperature. Furthermore, the composite membranes exhibited much higher selectivity (conductivity/methanol diffusion coefficient) compared with the pure SPEEK and Nafion^® 117 membranes. These results indicated that introducing the crosslinked CS layer onto the SPEEK surface was an effective method for improving the performance of the SPEEK membrane, especially for reducing the methanol crossover.     

The effective methanol-blocking and proton conductivity membranes based on sulfonated poly (ether ether ketone ketone) and polyorganosilicon with functional groups

To solve the conflict between high proton conductivity and low methanol crossover of pristine sulfonated aromatic polymer membranes, the polyorganosilicon doped sulfonated poly (ether ether ketone ketone) (SPEEKK) composite membranes were prepared by introducing polyorganosilicon additive with various functional groups into SPEEKK in this study. Scanning electron microcopy (SEM) images showed the obtained membranes were compact. No apparent agglomerations, cracks and pinholes were observed in the SEM images of composite membranes. The good compatibility between polymer and additive led to the interconnection, thus producing new materials with great characteristics and enhanced performance. Besides, the dual crosslinked structure could be formed in composite membranes through the condensation of silanols and the strong interaction between matrix and additive. The formation of dual crosslinked structure optimized the water absorption, enhanced the hydrolytic stability and oxidative stability of membranes. Especially, the incorporation of additive improved the strength and flexibility of composite membranes at the same time, meaning that the life of the composite membranes might be extended during the fuel cell operation. Meanwhile, the proton conductivity improved with increasing additive content due to the loading of more available acidic groups. It is noteworthy that at 25% additive loading, the proton conductivity reached a maximum value of 5.4 × 10⁻² S cm⁻¹ at 25 °C, which exceeded the corresponding value of Nafion^@ 117 (5.0 × 10⁻² S cm⁻¹) under same experimental conditions. The composite membrane with 20 wt% additive was found to produce the highest selectivity (1.22 × 10⁵ S cm⁻³) with proton conductivity of 4.70 × 10⁻² S cm⁻¹ and methanol diffusion coefficient of 3.85 × 10⁻⁷ cm² s⁻¹, suggesting its best potential as proton exchange membrane for direct methanol fuel cell application. The main novelty of our work is providing a feasible and environment-friendly way to prepare the self-made polyorganosilicon with various functional groups and introducing it into SPEEKK to fabricate the dual crosslinked membranes. This design produces new materials with outstanding performance.     

Synthesis and characterization of novel sulfonated poly(arylene ether ketone) copolymers with pendant carboxylic acid groups for proton exchange membranes

A series of novel side-chain-type sulfonated poly(arylene ether ketone)s with pendant carboxylic acid groups copolymers (C-SPAEKs) were synthesized by direct copolymerization of sodium 5,5′-carbonyl-bis(2-fluorobenzenesulfonate), 4,4′-difluorobenzophenone and 4,4′-bis(4-hydroxyphenyl) valeric acid (DPA). The expected structure of the sulfonated copolymers was confirmed by FT-IR and ¹H NMR. Membranes with good thermal and mechanical stability could be obtained by solvent cast process. It should be noted that the proton conductivity of these copolymers with high sulfonatation degree (DS > 0.6) was higher than 0.03 S cm⁻¹ and increased with increasing temperature. At 80 °C, the conductivity of C-SPAEK-3 (DS = 0.6) and C-SPAEK-4 (DS = 0.8) reached up to 0.12 and 0.16 S cm⁻¹, respectively, which were higher than that of Nafion 117 (0.10 S cm⁻¹). Moreover, their methanol permeability was much lower than that of Nafion 117. These results showed that the synthesized materials might have potential applications as the proton exchange membranes for DMFCs.     

Cross-linked poly(arylene ether ketone) electrolyte membranes with enhanced proton conduction for fuel cells

A new class of covalently cross-linkable poly(arylene ether ketone)s (cPAEKs) with sulfonic acid groups on both the backbone and pedant positions were synthesized. 3-Amino-1,5-napthalene disulfonic acid salt was chosen as a strong sulfonating agent for the preparation of csPAEK membranes with high sulfonation degree (SD). The major advantage of synthesized membranes is their exceptionally high-proton conductivities but still maintaining low methanol permeability and water uptake. All csPAEK membranes exhibited higher proton conductivity than Nafion^®117 over the temperature range of 40–90 °C. For example, among these membranes, csPAEK0 with the lowest SD shows a proton conductivities of 0.071 S cm⁻¹ at 40 °C and 0.118 S cm⁻¹ at 90 °C, which are higher than those of Nafion^®117 (0.057 S cm⁻¹ at 40 °C and 0.108 S cm⁻¹ at 90 °C). More interestingly, csPAEK0 appears to have a low water uptake, with values of only 22% at 40 °C and 27% at 90 °C, indicating high dimensional stability in hot water. Moreover, in many cases, csPAEK membranes with 15% cross-linking degree (CD) exhibited low methanol permeability, good thermal stability, and showed very high strain at break. The superior proton conduction, methanol permeation, and water uptake properties of the prepared membranes are of significant interest for both PEMFCs and DMFCs applications.