Hybrid supercapacitor based on MnO2 and columned FeOOH using Li2SO4 electrolyte solution

The nano-sized columned β-FeOOH was prepared by the hydrolysis process and its electrochemical capacitance performance was evaluated for the first time in Li₂SO₄ solution. A hybrid supercapacitor based on MnO₂ positive electrode and FeOOH negative electrode in Li₂SO₄ electrolyte solution was designed. The electrochemical tests demonstrated that the hybrid supercapacitor has a energy density of 12 Wh kg⁻¹ and a power density of 3700 W kg⁻¹ based on the total weight of the electrode active materials with a voltage range 0–1.85 V. This hybrid supercapacitor also exhibits a good cycling performance and keeps 85% of initial capacity over 2000 cycles.     

Electrochemical capacitance of NiO/Ru0.35V0.65O2 asymmetric electrochemical capacitor

A designed asymmetric hybrid electrochemical capacitor was presented where NiO and Ru_0.35V_0.65O₂ as the positive and negative electrode, respectively, both stored charge through reversible faradic pseudocapacitive reactions of the anions (OH⁻) with electroactive materials. And the two electrodes had been individually tested in 1 M KOH aqueous electrolyte to define the adequate balance of the active materials in the hybrid system as well as the working voltage of the capacitor based on them. The electrochemical tests demonstrated that the maximum specific capacitance and energy density of the asymmetric hybrid electrochemical capacitor were 102.6 F g⁻¹ and 41.2 Wh kg⁻¹, respectively, delivered at a current density of 7.5 A cm⁻². And the specific energy density decreased to 23.0 Wh kg⁻¹ when the specific power density increased up to 1416.7 W kg⁻¹. The hybrid electrochemical capacitor also exhibited a good electrochemical stability with 83.5% of the initial capacitance over consecutive 1500 cycle numbers.     

A cheap asymmetric supercapacitor with high energy at high power: Activated carbon//K0.27MnO2·0.6H2O

Studies of the electrochemical behavior of K_0.27MnO₂·0.6H₂O in K₂SO₄ show the reversible intercalation/deintercalation of K⁺-ions in the lattice. An asymmetric supercapacitor activated carbon (AC)/0.5 mol l⁻¹ K₂SO₄/K_0.27MnO₂·0.6H₂O was assembled and tested successfully. It shows an energy density of 25.3 Wh kg⁻¹ at a power density of 140 W kg⁻¹; at the same time it keeps a very good rate behavior with an energy density of 17.6 Wh kg⁻¹ at a power density of 2 kW kg⁻¹ based on the total mass of the active electrode materials, which is higher than that of AC/0.5 mol l⁻¹ Li₂SO₄/LiMn₂O₄. In addition, this asymmetric supercapacitor shows excellent cycling behavior without the need to remove oxygen from the electrolyte solution. This can be ascribed in part to the stability of the lamellar structure of K_0.27MnO₂·0.6H₂O. This asymmetric aqueous capacitor has great promise for practical applications due to high energy density at high power density.     

Hybrid supercapacitor with nano-TiP2O7 as intercalation electrode

Nano-size (≤100 nm) TiP₂O₇ is prepared by the urea assisted combustion synthesis, at 450 and 900 °C. The compound is characterized by powder X-ray diffraction, Rietveld refinement, high resolution transmission electron microscopy and surface area methods. Lithium cycling properties by way of galvanostatic cycling and cyclic voltammetry (CV) showed a reversible and stable capacity of 60 (±3) mAh g⁻¹ (0.5 mole of Li) up to 100 cycles, when cycled at 15 mA g⁻¹ between 2-3.4 V vs. Li. Non-aqueous hybrid supercapacitor, TiP₂O₇ (as anode) and activated carbon (AC) (as cathode) has been studied by galvanostatic cycling and CV in the range, 0-3 V at 31 mA g⁻¹ and exhibited a specific discharge capacitance of 29 (±1) F g⁻¹stable in the range, 100-500 cycles. The Ragone plot shows a deliverable maximum of 13 Wh kg⁻¹ and 371 W kg⁻¹ energy and power density, respectively.     

A new cheap asymmetric aqueous supercapacitor: Activated carbon//NaMnO2

A new cheap asymmetric supercapacitor based on activated carbon (AC) and NaMnO₂ as electrodes and aqueous Na₂SO₄ solution as electrolyte was assembled. It shows an energy density of 19.5 Wh kg⁻¹ at a power density of 130 W kg⁻¹ based on the total mass of the active electrode materials and an excellent cycling behavior. This asymmetric aqueous AC//NaMnO₂ capacitor is promising for practical applications due to its low price, easy preparation of NaMnO₂ and friendliness to environment.     

Electrochemical supercapacitor behavior of Ni3(Fe(CN)6)2(H2O) nanoparticles

Nanosized Ni₃(Fe(CN)₆)₂(H₂O) was prepared by a simple co-precipitation method. The electrochemical properties of the sample as the electrode material for supercapacitor were studied by cyclic voltammetry (CV), constant charge/discharge tests and electrochemical impedance spectroscopy (EIS). A specific capacitance of 574.7 F g⁻¹ was obtained at the current density of 0.2 A g⁻¹ in the potential range from 0.3 V to 0.6 V in 1 M KNO₃ electrolyte. Approximately 87.46% of specific discharge capacitance was remained at the current density of 1.4 A g⁻¹ after 1000 cycles.     

Electrochemical performance of carbon-coated lithium manganese silicate for asymmetric hybrid supercapacitors

Nanoscale carbon-coated Li₂MnSiO₄ powder is prepared using a conventional solid-state method and can be used as the negative electrode in a Li₂MnSiO₄/activated carbon (AC) hybrid supercapacitor. Carbon-coated Li₂MnSiO₄ material presents a well-developed orthorhombic crystal structure with a Pmn2₁ space group, although there is a small impurity of MnO. The maximum specific capacitance of the Li₂MnSiO₄/AC hybrid supercapacitor is 43.2 F g⁻¹ at 1 mA cm⁻² current density. The cell delivers a specific energy as high as 54 Wh kg⁻¹ at a specific power of 150 W kg⁻¹ and also exhibits an excellent cycle performance with more than 99% columbic efficiency and the maintenance of 85% of its initial capacitance after 1000 cycles.     

Dual functions of activated carbon in a positive electrode for MnO2-based hybrid supercapacitor

Utilizing the dual functions of activated carbon (AC) both as a conductive agent and an active substance of a positive electrode, a hybrid supercapacitor (AC-MnO₂&AC) with a composite of manganese dioxide (MnO₂) and activated carbon as the positive electrode (MnO₂&AC) and AC as the negative electrode is fabricated, which integrates approximate symmetric and asymmetric behaviors in the distinct parts of 2 V operating windows. MnO₂ in the positive electrode and AC in the negative electrode together form a pure asymmetric structure, which extends the operating voltage to 2 V due to the compensatory effect of opposite over-potentials. In the range of 0-1.1 V, both AC in the positive and negative electrode assemble as a symmetric structure via a parallel connection which offers more capacitance and less internal resistance. The optimal mass proportions of electrodes are calculated though a mathematical process. In a stable operating window of 2 V, the capacitance of AC-MnO₂&AC can reach 33.2 F g⁻¹. After 2500 cycles, maximum energy density is 18.2 Wh kg⁻¹ with a 4% loss compared to the initial cycle. The power density is 10.1 kW kg⁻¹ with an 8% loss.     

High energy density PbO2/activated carbon asymmetric electrochemical capacitor based on lead dioxide electrode with three-dimensional porous titanium substrate

A PbO₂/AC asymmetric electrochemical capacitor (AEC) with energy density as high as 49.4 Wh kg⁻¹, power density of 433.2 W kg⁻¹ and specific capacitance of 135.2 F g⁻¹ was fabricated with PbO₂ electrodeposited on three-dimensional porous titanium (3D-Ti/PbO₂) and activated carbon. The high electrochemical active surface of 3D-Ti/PbO₂ resulted in high specific capacity making it suitable for use as positive electrode in PbO₂/AC AEC. The fabricated AEC demonstrated good power performance with an energy density conservation of 30 Wh kg⁻¹ at power density of 2078 W kg⁻¹. The fabricated AEC also showed excellent cycling stability with capacitance retention of 99.2% after 1000 cycles.     

Enhancement of the energy storage properties of supercapacitors using graphene nanosheets dispersed with metal oxide-loaded carbon nanotubes

Graphene nanosheets (GNs) dispersed with SnO₂ nanoparticles loaded multiwalled carbon nanotubes (SnO₂-MWCNTs) were investigated as electrode materials for supercapacitors. SnO₂-MWCNTs were obtained by a chemical method followed by calcination. GNs/SnO₂-MWCNTs nanocomposites were prepared by ultrasonication of the GNs and SnO₂-MWCNTs. Electrochemical double layer capacitors were fabricated using the composite as the electrode material and aqueous KOH as the electrolyte. Electrochemical performance of the composite electrodes were compared to that of pure GNs electrodes and the results are discussed. Electrochemical measurements show that the maximum specific capacitance, power density and energy density obtained for supercapacitor using GNs/SnO₂-MWCNTs nanocomposite electrodes were respectively 224 F g⁻¹, 17.6 kW kg⁻¹ and 31 Wh kg⁻¹. The fabricated supercapacitor device exhibited excellent cycle life with ∼81% of the initial specific capacitance retained after 6000 cycles. The results suggest that the hybrid composite is a promising supercapacitor electrode material.     

A dye-sensitized photo-supercapacitor based on PProDOT-Et2 thick films

A photo-rechargeable supercapacitor (photo-supercapacitor, or PSC) is studied using a N3-dye adsorbed TiO₂ photoelectrode and PProDOT-Et₂ poly(3,3-diethyl-3,4-dihydro-2H-thieno-[3,4-b][1,4]dioxepine) polymer films as supercapacitor materials for electron storage. The PSC device, comprising a dye-sensitized solar cell (DSSC) and a supercapacitor (SC), can store the photo-to-electric energy. The PProDOT-Et₂ films are potentiostatically electropolymerized to form thick films (ca. 0.5 mm) with a specific capacitance of ca. 6.5 F cm⁻². A symmetrical (p/p) supercapacitor, with PProDOT-Et₂ coated on both electrodes, is also characterized before fabricating the three-electrode PSC. The PSC is tested under light illumination of 100 mW cm⁻², and attaining a photocharged voltage of 0.75 V and a discharged energy density of 21.3 μWh cm⁻².     

An asymmetric anthraquinone-modified carbon/ruthenium oxide supercapacitor

An asymmetric supercapacitor with improved energy and power density, relative to a symmetric Ru oxide device, has been constructed with anthraquinone-modified carbon fabric (Spectracarb 2225) as the negative electrode and Ru oxide as the positive electrode. The performance of the supercapacitor was characterized by cyclic voltammetry and constant current discharging. Use of the anthraquinone-modified electrode extends the negative potential limit that can be used, relative to Ru oxide, and allows higher cell voltages to be used. The maximum energy density obtained was 26.7 Wh kg⁻¹ and an energy density of 12.7 Wh kg⁻¹ was obtained at a 0.8 A cm⁻² discharge rate and average power density of 17.3 kW kg⁻¹. The C-AQ/Ru oxide supercapacitor requires 64% less Ru relative to a symmetric Ru oxide supercapacitor.     

Intercalation of PF6 anion into graphitic carbon with nano pore for dual carbon cell with high capacity

Intercalation property of PF₆⁻ into graphitic carbon was studied for a hybrid capacitor with different ratio of cathode and anode amount. Graphene sheet distance increased with increasing PF₆⁻ intercalation amount and it saturated at 0.4 nm at high applied potential, which is corresponded to stage 2 structure. On the other hand, it was found that nano size pore into graphene sheet was introduced at higher applied potential with 20 times larger anode carbon and this nano porous carbon shows a large capacity for intercalation capacity of 147 mAh g⁻¹. The estimated energy density of the hybrid capacitor using carbon with nano bubble structure was ca. 400 Wh kg⁻¹.     

Graphene-MnO2 and graphene asymmetrical electrochemical capacitor with a high energy density in aqueous electrolyte

The graphene-manganese oxide hybrid material has been prepared by solution-phase assembly of aqueous dispersions of graphene nanosheets and manganese oxide nanosheets at room temperature. The morphology and structure of the obtained material are examined by scanning electron microscopy, transition electron microscopy, X-ray diffraction and N₂ adsorption-desorption. Electrochemical properties are characterized by cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy. An asymmetric electrochemical capacitor with high energy and power densities based on the graphene-manganese oxide hybrid material as positive electrode and graphene as negative electrode in a neutral aqueous Na₂SO₄ solution as electrolyte is assembled. The asymmetrical electrochemical capacitor could cycle reversibly in a voltage of 0-1.7 V and give an energy density of 10.03 Wh kg⁻¹ even at an average power density of 2.53 kW kg⁻¹. Moreover, the asymmetrical electrochemical capacitor exhibit excellent cycle stability, and the capacitance retention of the asymmetrical electrochemical capacitor is 69% after repeating the galvanostatic charge-discharge test at the constant current density of 2230 mA g⁻¹ for 10,000 cycles.     

Characterization of MnFe2O4/LiMn2O4 aqueous asymmetric supercapacitor

A new type of asymmetric supercapacitor containing a MnFe₂O₄ negative electrode and a LiMn₂O₄ positive electrode in aqueous LiNO₃ electrolyte has been synthesized and characterized. The nanocrystalline MnFe₂O₄ anode material has a specific capacitance of 99 F g⁻¹ and the LiMn₂O₄ cathode a specific capacity of 130-100 mAh g⁻¹ under 10-100 C rate. The cell has a maximum operating voltage window of ca. 1.3 V, limited by irreversible reaction of MnFe₂O₄ toward reducing potential. The specific power and specific energy of the full-cell increase with increasing anode-to-cathode mass ratio (A/C) and saturate at A/C ∼4.0, which gives specific cell energies, based on total mass of the two electrodes, of 10 and 5.5 Wh kg⁻¹ at 0.3 and 1.8 kW kg⁻¹, respectively. The cell shows good cycling stability and exhibits significantly slower self-discharge rate than either the MnFe₂O₄ symmetric cell or the other asymmetric cells having the same cathode but different anode materials, including activated carbon fiber and MnO₂.     

Rate-controlling species for the sintering of LiTi2(PO4)3

A series of Li deficient LiTi₂(PO₄)₃ samples were prepared and sintered and the density was measured to determine the rate-controlling species for sintering of LiTi₂(PO₄)₃. It was observed that as the Li content decreased the density decreased. This result suggests that oxygen does not control sintering. A comparison of the LiTi₂(PO₄)₃ sintering data to sintering and diffusion data in olivine, which exhibits a similar framework structure to LiTi₂(PO₄)₃, suggests that P is the species which controls sintering. This suggestion was confirmed by the density results of a Li excess LiTi₂(PO₄)₃ sample.     

Li3V2(PO4)3 cathode material synthesized by chemical reduction and lithiation method

The monoclinic-type Li₃V₂(PO₄)₃ cathode material was synthesized via calcining amorphous Li₃V₂(PO₄)₃ obtained by chemical reduction and lithiation of V₂O₅ using oxalic acid as reducer and lithium carbonate as lithium source in alcohol solution. The amorphous Li₃V₂(PO₄)₃ precursor was characterized by using TG–DSC and XPS. The results showed that the V⁵⁺ was reduced to V³⁺ by oxalic acid at ambient temperature and pressure. The prepared Li₃V₂(PO₄)₃ was characterized by XRD and SEM. The results indicated the Li₃V₂(PO₄)₃ powder had good crystallinity and mesoporous morphology with an average diameter of about 30 nm. The pure Li₃V₂(PO₄)₃ exhibits a stable discharge capacity of 130.08 mAh g⁻¹ at 0.1 C (14 mA g⁻¹).     

LiCr0.2Ni0.4Mn1.4O4 spinels exhibiting huge rate capability at 25 and 55 °C: Analysis of the effect of the particle size

The comparison of the rate capability of LiCr_0.2Ni_0.4Mn_1.4O₄ spinels synthesized by the sucrose aided combustion method at 900, 950 and 1000 °C is presented. XRD and TEM studies show that the spinel cubic structure remains unchanged on heating but the particle size is notably modified. Indeed, it increases from 695 nm at 900 °C to 1465 nm at 1000 °C. The electrochemical properties have been evaluated by galvanostatic cycling at 25 and 55 °C between 1 C and 60 C discharge rates. At both temperatures, all samples exhibit high working voltage (∼4.7 V), elevated capacity (∼140 mAh g⁻¹) and high cyclability (capacity retention ∼99% after 50 cycles even at 55 °C). The samples also have huge rate capability. They retain more than 70% of their maximum capacity at the very fast rate of 60 C. The effect of the particle size on the rate capability at 25 and at 55 °C has been investigated. It was demonstrated that LiCr_0.2Ni_0.4Mn_1.4O₄ annealed at 900 °C, with the lowest particle size, has the best electrochemical performances. In fact, among the LiNi_0.5Mn_1.5O₄-based cathodes, SAC900 exhibits the highest rate capability ever published. This spinel, able to deliver 31,000 W kg⁻¹ at 25 °C and 27,500 W kg⁻¹ at 55 °C is a really promising cathode for high-power Li-ion battery.     

A high energy Li-ion battery based on nanosized LiNi0.5Mn1.5O4 cathode material

The electrochemical performance of a Li-ion battery made from nanometric, highly crystalline LiNi_0.5Mn_1.5O₄ as positive electrode and mesoporous carbon microbeads (MCMBs) as negative electrode was assessed. The best performance was obtained by using a slight excess of spinel (a cathode/anode mole ratio of 1.3) and lithium bis-oxalate borate (LiBOB) instead of LiPF₆ as an electrolyte salt. Higher spinel contents caused the formation of metallic Li in the carbon and the rapid degradation of battery performance as a result. The calculated output energy was 322 Wh kg⁻¹ which is higher than the value reported for the LiMn₂O₄/C cell (250 Wh kg⁻¹).     

Asymmetric capacitor based on superior porous Ni-Zn-Co oxide/hydroxide and carbon electrodes

Hierarchical porous multi-phase Ni-Zn-Co oxide/hydroxide is synthesized by using metal-organic framework-5 (MOF-5) as the template. Hierarchical porous carbon is obtained by the facile direct decomposition of the MOF-5 framework with phenolic resin. The structures and textures are characterized by X-ray diffraction, high-resolution transmission electron microscopy, scanning electron microscopy, and nitrogen sorption at 77 K. An asymmetric capacitor incorporating the Ni-Zn-Co oxide/hydroxide as the positive electrode and the porous carbon as the negative electrode is fabricated. A maximum energy density of 41.65 Wh kg⁻¹ is obtained, which outperforms many other available asymmetric capacitors. The asymmetric capacitor also shows a good high-rate performance, possessing an energy density of 16.62 Wh kg⁻¹ at the power density of about 2900 W kg⁻¹.